Search Documents

By R. J. Sheets

In 2009, the Gold Quarry openpit mine experienced multiple large-scale slope failures of the upper east highwall that reduced gold ore extraction for nearly 18 months. The slope failures occurred within a weak, consolidated sedimentary sequence that exhibits strength characteristics that are transitional between soil and rock. Instability initiated as mining exposed the lower, high plasticity subunits of the Carlin Formation. This deformation created preferential flow paths that allowed ground water from the upper sandy subunits to infiltrate low-permeability, clay-rich subunits, thereby enhancing deformation of the slope toe, which, in turn, destabilized the upper portion of the highwall. The outcome was a 160 m high slope failure that had a lateral run-out of 850 m. The effort to return the pit to ore production required geotechnical and hydrogeological investigations and the preliminary remediation mining activity to be concurrent. This required the development of detailed safety procedures and a requirement to modify the remediation design as new results were obtained. An initial challenge was to mitigate a near vertical, 90 m headscarp with localized, blast-induced slope failures. Back-analyses with numerical modeling software indicated that the failure surface could be shallower, which contradicted the initial failure interpretations. Eventually, drilling results confirmed this alternative failure geometry. The final remediation design incorporated shallower slope geometries and an approximately 3 Mt buttress along the base of the Carlin Formation and bedrock contact to reinforce the subunits with residual strength properties. The results are a stable highwall within the Carlin Formation following nearly 10 years of repeated slope failures, and an example of the necessity to conduct appropriate geotechnical and hydrogeological studies during the early stages of a new layback evaluation or new openpit development.

By Hernán Alvarado

"En los últimos años, la minería ha utilizado los relaves de concentradora, previamente deslamados como material de relleno en las labores subterraneas. Sin embargo, el tonelaje disponible por este sistema no satisface lasnecesidades de relleno de la mina. En ese sentido, el presente texto señala la aplicabilidad del sistema complementario en la mina Francois. Por ello, se han considerado dos sistemas principales para la recuperación y tratamiento de los relaves antiguos: Dragado e Hidráulica. Estos sistemas contienen un equipo de extracción y dilución del relave antiguo, equipo de bombeo, estación de tratamiento para los relaves antiguos, el equipo de almacenamiento y dosaje y equipo de bombeo. Las variantes de los dos sistemas son: equipos, densidades del relave y volumen de agua. De forma que la cantidad de agua recuperada de los relaves de flotación es suficiente para operar el circuito con cualesquiera de los sistemas propuestos. "

Sep 1, 1964

Pese a tener cajas sólidas en su estructura, algunas vetas desarrollan un relleno frágil, ocasionando problemas futuros de sostenimiento para el "corte y relleno" de los mismos. Por ello, se utilizó el método de los "Square Sets", donde además de ser costoso, implicaba eliminar una proporción de la roca encajonante y diluía el contenido metálico de los filones. En ese sentido, el objetivo del texto es señalar la viabilidad del "método Cornish"como método alternativo, económico, de rendimiento óptimo y que no presenta riesgos para el personal o la labor realizada. Este método es aplicable en aquellas vetas uniformes no falladas, que tengan desde una potencia pequeña hasta aquella que sea posible apuntalar, así como en aquellas que requieran sostenimiento del techo en la veta mima o donde se realizen Shrinkages. El proceso del método se basa en la preparación de los tajeos, luego en la explotación(perforación y disparos), enmaderado, relleno del tajeo, recuperación de madera, las variantes en la preparación del tajeo y la recuperación del mineral. La única desventaja que ofrece este método es su peligrosidad, dado que si se aplica en zonas inadecuadas o sin la supervisión que garantice el cumplimiento de las normas preventivas, es preferible el uso de los "Square Sets". Sin embargo, la aplicación del método resulta mucho más productiva en rendimiento teórico puesto que alcanza de 7 a 10 toneladas por tarea de 8 horas y responde satisfactoriamente siempre y cuando las condiciones de las vetas lo permita.

Jul 20, 1957

The Australian Gas Light. Company was established in 1837, the first gas being sent out from the Kent Street Works, then the headquarters, in 1841. Mortlake Works were opened in 1886, and has since grown to the vast undertaking inspected by members of the Institute.The Kent Street Works were closed in 1921. The area of the, company's property at Mortlake is 117 acres.Some interesting figures from the statistics of the company's activities for 1937 are:-

Jan 1, 1938

By Fernández H. Carlos

Debido que el subproducto en la etapa de lixiviación de las calcinas de zinc, alcanza un 18% de plomo y 40% de plata en la refinería de Cajamarquilla, es necesario la recuperación de sus elementos valiosos a través de un procedimiento hidrometalúrgico donde se obtengan extracciones en plomo y plata del orden de 85% respectivamente. En este sentido, el texto señala la solubilidad del plomo y la plata en una solución con excesos de iones cloruros y así someter al residuo a una lixiviación ácido clorurante de altas temperaturas y con presencia de un agente oxidante. Una vez obtenida la solución, se divide el plomo y la plata por cementaciones sucesivas con polvo de zinc. Finalmente, se determina la factibilidad del procedimiento para la extracción de los elementos valiosos del residuo y se disminuye los costos de la refinación del zinc.

Nov 8, 1984

By Vincent Tirolo

Two separate secant pile cofferdams were constructed as part of an extensive rehabilitation and modernization of the New York City Transit's Lexington Avenue/Third Avenue IND Station at 53rd Street in Manhattan. Major high rise structures and outpatient hospital facilities bordered the site. The roadway is an important east-west corridor in mid-Manhattan. In order to perform the construction of new escalator and elevator shafts over 250 linear feet of secant wall was installed to the top of rock or to the existing subway roof. Much of the secant wall was constructed from below a temporary roadway decking system using a low headroom rig. The roadway decking system was supported on shallow spread footings. The secant piles were drilled using crawler mounted hydraulic rotary drill rigs. The secant wall provided a watertight, rigid cofferdam that minimized settlement and other disruptions to existing structures and utilities. During later stages of the project the secant wall also supported the roadway decking system.

Jan 1, 2003

By Lucas Barcelos Dias

A demanda por materiais ecológicos vem crescendo exponencialmente nos últimos anos. O potencial destes produtos é dado tanto pela versatilidade em seu uso quanto pela sua disponibilidade na natureza. Um dos materiais em expansão é o OSB (Oriented Strand Board), utilizado na vedação do Steel Frame. O trabalho tem como objetivo substituir em três porcentagens 15%, 30%, 45% das tiras de madeira do OSB convencional pela fibra do epicarpo do coco de babaçu (FECB), a fim de melhorar a resistência mecânica. Os resultados obtidos na chapa de 11 mm incorporada com FECB apresentaram resistência a tração entre 15 e 26 MPa e de flexão entre 42 e 75 MPa, tornando assim superiores ao produto encontrado no mercado.

Oct 30, 2017

By Rafael Wilson Soares Ladeira

Realizar manutenções preditivas de forma cada vez mais assertiva é um dos benefícios da atual evolução dos sistemas produtivos industriais conhecida como Indústria 4.0. A Sotreq - revendedora Caterpillar - oferece um serviço de análise de fluidos a partir da coleta periódica para máquinas operantes em campo. Com os resultados das medições, especialistas atribuem às amostras um nível de criticidade, justificativas e recomendações. Neste trabalho propõe-se uma solução que aumentou a eficiência desse processo através da utilização de modelos de Machine Learning treinados com as análises já realizadas que automatizam a classificação e a geração do texto de diagnóstico para novas amostras. As predições do sistema foram consideradas bem sucedidas, com métricas de sensibilidade e especificidade acima de 88%.

Oct 30, 2017

By Gualberto Carpio

El presente texto señala la metodología desarrollada en Tintaya para la identificación de posibles proyectos, los cuales están enfocados con los objetivos del negocio y del líder del área ya que comparten metas comunes de mejoramiento. Esta mejora alcanzada con Six Sigma, solo es posible con el soporte del plan estratégico de la compañía y por ende, se hace énfasis en la correlación que existe con los proyectos a desarrollar en todas las áreas. En este sentido, el plan estratégico es alineado y controlado por indicadores clave de desempeño (KPIs) de primer, segundo y tercer nivel, los cuales indirectamente norman el desarrollo de los proyectos planteando metas de costos, incremento de producción, productividad, reducción de tiempos de ciclo, etc.

Sep 19, 2006

By Georg Petersen

El Perú es un país rico en diversidad de metales empleados en los campos de la minería, metalurgia, orfebrería y artesanía durante los tiempos pre-históricos. Dichos metales son: oro (objetos laminados por martilleo, repujados, pulidos, vaciados, soldados y dorados), plata (objetos trabajados de la misma manera que los de oro), cobre (objetos en diversas formas, como son discos, recipientes, herramientas y armas, en muchos casos dorados y/o plateados) y el azogue (cinabrio usado preferentemente para pintar las caras de los guerreros, las máscaras de los fardos funerarios y las caras de las mujeres nobles, costumbre que se generalizó a principios de la época colonial). De otro lado, existen otros cuatro metales que se emplearon en cantidades pequeñas como: fierro, platino, plomo, estaño.

Nov 1, 1970

By José Luis Vitteri

Dado que se generan largas colas de los camiones mineros en los puntos de carga, es necesario revisar las causas principales que la originan. Entre estas tenemos: el desconocimiento de la variabilidad y sus efectos nocivos y la aceptación de que el mínimo costo de operación se obtiene con la mayor utilización de la excavadora. En este sentido, el presente texto describe el manejo de la variabilidad en los procesos de carguío y transporte con equipos pesados a través del estudio de sus causas, de forma que la única manera correcta de reducir el perjuicio de la variabilidad en el transporte, es manipulando la frecuencia inicial de los camiones.

Oct 1, 2013

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

U.S. demand for building and construction materials, such as construction aggregate, gypsum, and cement, remained strong in 1989. Cement imports declined slightly, representing about 17% of apparent consumption compared with 19% in 1988. Mexico, supplying 29% of the total, was the primary source of imports, followed by Canada with 21 %, Japan with 14%, and Spain and Greece with 10% each. Mexico was also the target of an antidumping petition, filed by producers in Arizona, Florida, New Mexico, and Texas, alleging that Mexican cement was being sold in these areas at less than fair value. This was the second petition filed against Mexico in the last 3 years. The International Trade Commission made a preliminary determination that the cement industry in these regions was materially injured by Mexican imports. U.S. demand improved for construction aggregate for the fourth consecutive year and was at a near-record level. The U.S. gypsum industry performed well, even though new housing starts decreased for the third consecutive year. Increased U.S. exports of gypsum wallboard and strength in the remodeling markets offset the impact of declining housing starts.

Jan 1, 1990

GENTLEMEN, lt is with much pleasure I meet you tonight at this the second meeting of the Australasian Institute of Mining Engineers, held in Western Australia, and I sincerely thank you for the honour you have conferred upon me in electing me as your President. I greatly appreciate the distinction, and will endeavour to fulfil the duties of the office to the best of my ability, and hope to prove a worthy successor to those gentlemen who have held the position before me. On behalf of the local members of the Institute, I extend a hearty welcome to the members from the other States of the Commonwealth, who have come so far to attend this meeting, and also to the non-members whom we have invited this evening. We are especially pleased to have Mr. Gregory, our Minister of Mines and Railways, and the Government and School of Mines officials with us; and I take this opportunity to thank the Premier, Mr. Gregory, and the Government officials for the assistance given us, and for doing so much to make the visit of our members from the other States so pleasant and instructive. I have also to thank the Mayor and Councillors of Kalgoorlie for the courtesy and hospitality given to our members, which is much appreciated.I assume you want me to follow the time-honoured custom of giving a Presidential address...

Jan 1, 1909

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By Williams K. C

This paper presents a brief account of the plant which has been developed at Port Pirie to recover, by vacuum distillation, the greater part of the zinc content of desilverized lead. The present plant is an experimental unit, which is run in conjunction with the normal refinery practice, but can be cut out of the circuit. It will shortly be dismantled and duplicate units will be built on the sites chosen for the final plant installation.The unit described here has treated flows of 16 to 37 tons per hour of desilverized lead, to recover 90 to 95 per cent of the zinc contained in it. It is not intended here to detail all aspects of the vacuum dezincing operation, nor the developments which precededthe adoption of this design. The essential features of the present plant will be described and, where these are peculiar to the present experimental location, the intended alteration for the final plant will also be mentioned. OUTLINE OF PLANT AND PROCESSLead issues from the continuous desilverizing kettle at about 350° C. containing about 0·57 per cent Zn. It is conveyed by a tiled launder to the preheater, where it is heated to 580-620° C.Hot lead from the preheater enters the vacuum vessel via a barometric leg. From a reservoir holding about 19 tons of lead it falls by gravity in a thin film exposed to high vacuum (20-50 microns)3 and leaves the vessel via a barometric leg, entering the lead pot. The lead leaves this pot at 540-560° C., containing 0·03 to 0·06 per cent Zn, which is removed, together with residual antimony of 0.02 to 0·06 per cent, by a separate final refining process.

Jan 1, 1956

By Guillermo Velarde

El presente trabajo describe el proceso de irrigación del mineral con la solución lixiviante en los flujos unitarios en la lixiviación de minerales. Fue necesario conceptuar el término demanda de lixiviante para expresar el requerimiento de volumen lixiviante o utilización en una condición de adición extrema (alta) o límite, que la cinética puede todavía responder. Este concepto fue fundamental para evaluar los próximos los flujos de irrigación a los niveles máximos desde el punto de vista cinético. La demanda de lixiviante y la etapa controlante del proceso en cualquier momento de la lixiviación pueden ser estimadas práctica y confiablemente con el rate m3/kg Cu, lo que permite actuar calculadamente en la irrigación y posibilita agregar otra acción para elevar la temperatura de la pila.

Sep 13, 2001

By Rodríguez V. Raymundo E.

El presente trabajo describe la evaluación del uso de brocas tricónicas como herramientas principales de perforación en el yacimiento minero de Cerro Verde, Arequipa. La óptima utilización de esta herramienta representa el 30% de los costos totales de perforación, los cuales se ven reflejados en los factores de análisis a considerar para la superación de performances y las perspectivas que se aplicarán en el futuro para alcanzar mejores rendimientos y bajar los costos de perforación.

Oct 14, 1980

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By Raúl Daniel López

Un objetivo de seguridad y calidad en los moldes de la colada continua de Siderar fue la de tener un menisco estable y controlado. A lo largo de los distintos periodos de inversiones y mejoras, el control de nivel de Siderar logro como objetivo contener su variación de nivel de acero en el molde en un rango de variación menor a +/-2 mm y con una velocidad de cambio inferior a 1,5 m/segundos. Esta etapa trajo una relativa mejora en los aspectos mencionados (calidad y continuidad operativa) pero el hecho de tener como sistema de medición de nivel un sistema radiactivo (fuente Co60 y contador de centelleo) mantenía serias limitaciones en ambos rubros dado que este sistema no diferencia la interface escoria /polvo colador con el menisco de acero. Este trabajo tratará de mostrar y contar las tareas de desarrollo y aplicación de esta nueva tecnología, hoy vigente en la nueva Colada Continua N° 2 (CCD2) y en etapa de puesta en marcha de la CCD1.

Aug 15, 2017