Search Documents

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By J. M. Gregg, C. J. Persellin, I. D. Somerville, E. A. Atekwana, K. L. Shelton

"Zn-Pb sulfide mineralization at Abbeytown mine and Twigspark quarry comprise the only known car¬bonate-hosted base metal sulfide deposits in the Sligo syncline, northwest Ireland. Limestone sedimentation occurred uniformly throughout the region during the Early Carboniferous (Mississippian) as observed by field relationships and lithofacies; however, petrographic and stable isotope evidence indicate that host-rock dolomitization occurred under different conditions at localities to the west and east of the Ox Mountains inlier, suggesting significant uplift and geologic isolation of these areas prior to dolomitization. Localized fluid flow systems are thought to be responsible for sulfide mineralization and associated epigenetic carbonate cements. West of the Ox Mountains inlier at Abbeytown, evidence of three geochemically distinct fluids are observed: (1) a lower-temperature, lower-salinity fluid (70°-130-°C, 4-9 wt.% equiv. NaCl); (2) a lower-temperature, higher-salinity fluid (70°-140°C, 15-24 wt.% equiv. NaCl); and (3) a higher-temperature, moderate-salinity fluid (165°-220°C, 8-14 wt.% equiv. NaCl). Similar fluid types were observed at the Twigspark deposit. The source of the higher-salinity fluid is likely seawater evaporated to near the point of halite precipitation. The higher-temperature fluid is thought to have been derived from deep circulation of basinal brines. It is speculated that mixing of the higher-salinity fluid with the high-temperature fluid was vital for ore formation at Abbeytown because fluid inclusions in sphalerite have homogenization temperatures and salinity values that fall along a mixing trajectory of these end member fluids. Also, areas where the high-salinity end member fluid is absent are barren of sulfides. Less complex fluid systems are indicated for sites east of the Ox Mountains inlier where no sulfide mineralization was observed. Data from base metal sulfide prospects in northwest Ireland indicate no connection with the regionally extensive flow system thought to be responsible for Zn-Pb deposits throughout the Irish Midlands.Les minéralisations en sulfures de Zn-Pb de la mine Abbeytown et de la carrière Twigspark sont les seules gîtes de métaux usuels à encaissant carbonaté connus dans le synclinal de Sligo, au nord-ouest de l’Irlande. Ces carbonates se sont déposés d’une manière uniforme dans la région au Carbonifère inférieur (Mississippien) tel que l’indiquent les relations de terrain et les lithofaçiès; les données pétrographiques et d’isotopes stables indiquent toutefois que la dolomitisation de l’encaissant s’est faite sous des conditions différentes aux localités situées à l’ouest ou à l’est de la boutonnière des Ox Mountains, ce qui suggère un soulèvement et une isolation géologique significative de ces secteurs avant la dolomitisation. L’action de systèmes de circulation locaux sont considérés être à l’origine de la minéralisation sulfurée et des ciments carbonatés épigénétiques qui leur sont associés. À Abbeytown, à l’ouest de la boutonnière des Ox Mountains, on note les effets de trois fluides géochimiquement distincts: (1) un fluide à basse température peu salin (70°-130°C, 4-9% poids équivalent NaCl); (2) un fluide à basse température fortement salin (70°-140°C, 15-24% poids équivalent NaCl); and (3) un fluide formé à plus haute température et salinité modérée (165°-220°C, 8-14% poids équivalent NaCl). Des fluides similaires ont été observés au gîte Twigspark. La source présumée du fluide le plus salin est de l’eau de mer amenée par évaporation près du point de précipitation de la halite. Le fluide à plus haute température est probablement dérivé de la circulation profonde de saumures dérivées d’un bas¬sin sédimentaire. Il est possible que le mélange du fluide à haute salinité avec celui à haute température ait joué un rôle central dans la genèse de la minéralisation d’Abbeytown parce que les températures d’homogénéisation et les valeurs de salinité des inclusions fluide"

Jan 1, 2009

By Rudy Beltrán, Kellyn Cristobal

El presente trabajo muestra las mejoras realizadas en nuestras operaciones mineras, respecto a disminuir los accidentes que se han venido presentando en diversas minas a nivel nacional, relacionadas al uso de los calibradores para controlar el espesor del shotcrete (concreto lanzado), donde el personal se expone a la línea de fuego cuando el concreto aún se encuentra en proceso de fraguado para alcanzar las resistencias iniciales de sostenimiento. Ante esta problemática, se ha diseñado un mecanismo automatizado que se encuentra adaptado al equipo robot lanzador de concreto, el cual elimina la exposición del personal durante este proceso y ademas asegura la calidad del espesor de shotcrete aplicado en las labores mineras.

Sep 29, 2023

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By Arthur R. MacPherson

Este capítulo revisa las etapas que deben seguirse desde el momento de considerar la molienda autógena en el desarrollo de un nuevo depósito de mineral o en la expansión de una planta existente, hasta la compra de un molino autógeno. En este caso el término autógeno incluye: semi-autógeno, molinos de pebbles secundarios y molino de bolos (trozos), así como los sistemas de molienda autógena total. También se han incluido las alternativas por vía húmeda y seca. Antes de programar el ensayo debe decidirse cuantas muestras brutas son requeridas para calcular propiamente las posibilidades de molienda autógena del depósito. También ha de tomarse la decisión, de como y donde deben tomarse las muestras, por ejemplo: planta piloto situada en el sitio de localización de la planta o en otro lugar establecido; molienda en húmedo y/o en seco....etc. En el mismo programa del ensayo se obtendrán ciertos datos fundamentales. Los ensayos deberán incluir un trabajo suficiente. para determinar cuál de las moliendas, totalmente autógena o semi-autógena, debe utilizarse; y qué tipo produce la máxima eficacia en la potencia consumida. También, los otros datos pertinentes deben ser recolectados, como por ejemplo: potencias, tonelajes, alimentación, carga, tamaño del producto, carga circulante, etc. Si es necesaria una molienda secundaria para obtener el tamano final, la decisión de qué molienda debe emplearse (molino de pebbles o molino de bolas) puede requerirse un ensayo de trabajo adicional. Finalmente, la concentración del mineral puede jugar un papel importante en la selección del circuito y debería ser una parte del ensayo final una vez que se ha establecido la molienda. Para determinar qué tipo de molinos pueden satisfacer los requerimientos establecidos por la planta piloto, debe tomarse una escala para ciertos datos como: potencia del molino, consumo de acero, simple o doble etapa de molienda, tipo de molino secundario. Para asegurar un posterior entendimiento del depósito de mineral y sus características de molienda, deberán efectuarse algunos trabajos adicionales a pequena escala utilizando pequeñas muestras y molinos para producir unos datos comparables de molienda. También, algunos ensayos tales como medio de molienda óptimo, e índice de trabajo, deberán ser completados.

Jan 1, 1982

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

By Dennis J. Riley

A. This outline addresses what a sub-contractor, or a subsub-contractor should do to get paid in the event the general contractor or building owner files for bankruptcy. B. Negotiating payment terms. Progress payments vs. "pay when paid". How a sub or subsub can avoid financing the contract. C. Court interpretation of "pay when paid" clauses allow postponement not excusal of payment. See, e.g., Seal Tite Corporation v. Ehret. Inc., 589 F. Supp. 701 (D.N.J. 1984) (where the court held that the general contractor could not delay payment indefinitely to the subcontractor in the event of non-payment from the owner); United Plate Glass Co. v. Metal Industries. Inc., 525 A.2d 468 (Commw. Ct. Pa. 1987) (where the court held that payment from owner was not a condition precedent to paying subcontractor but instead a timing mechanism indicating when payment should be made); But see. Straham v. Landis Construction Co., 499 So. 2d 417 (La. App. 4 Cir. 1986) (where the court strictly interpreted the "pay when paid" clause).

Jan 1, 1991

A New Technology of Applying SLon-2500 Magnetic Separator to Recover Iron Concentrate from Abandoned Tails

Sep 13, 2010

By Geraldo Lúcio de Faria

O sucesso do transporte ferroviário depende, entre outras coisas, da integridade física dos componentes metálicos empregados na via permanente. Um dos mais importantes é o trilho, pois falhas catastróficas deste componente podem gerar graves acidentes. No intuito de desenvolver aços com bom desempenho para esta aplicação, estudos têm sido desenvolvidos para se entender os efeitos de composição química e histórico de processamento termomecânico sobre a microestrutura e propriedades mecânicas dos aços. Neste contexto, este trabalho caracterizou microestruturalmente dois aços de aplicação ferroviária, sendo um Standard e um Premium. Amostras representativas destes aços foram submetidas a ensaios dilatométricos e a cinética de transformação de fases austenita-perlita foi investigada. Por meio dos resultados obtidos, foi possível concluir que o aço Premium estudado possui microestrutura mais refinada e que este efeito é devido, principalmente, à menor concentração de Mn em sua composição química. O menor teor de Mn facilita a nucleação de cementita eutetóide, possibilitando a formação de perlita em tempos mais curtos e temperaturas mais baixas do que no aço Standard. Isto possibilita que o aço Premium, em seu processo de fabricação, possa ser resfriado a taxas mais elevadas do que o Standard sem formação de martensita, justificando sua estrutura mais refinada.

Aug 17, 2017

By Guomin Jiang

Potassium ferrate is an excellent multifunctional reagent for wastewater treatment, but its preparation is crucial. The improved hypochlorite oxidation method was used to prepare potassium ferrate in this study. Iron nitrate, the preferred iron source, was added into hypochlorite solution and then the stabilization agent was added during the purification process of product. The influence of available chlorine content, iron molecular proportion, reaction temperature and reaction time on potassium ferrate preparation was investigated. The optimal condition for potassium ferrate preparation is 15% of available chlorine content , 0.6 of iron molecular proportion , 30i of reaction temperature , 45min of reaction time. The yield of potassium ferrate is about 67% with high purity (> 99%). The structure and performances of the product was characterized by XRD, EDX, SEM, TG and IR and the results show that the prepared product is consistent with the properties of potassium ferrate(VI).

Jan 1, 2010

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By Miguel A. Huamán G.

Los estudios realizados en la última década señalan que los depósitos estratoligados y estratiformes del contacto Mitu Pucará, se relacionan con el evento conocido como "volcanogénico regional", donde se realiza la reactivación del "nuevo volcánico" a través del depósito de la mineralización piritosa y polimetálica. Posteriormente dichos yacimientos piritosos son transformados hasta atravesar los plegamientos, fallamientos, intrusiones y la mineralización cretásico-terciaria. En este sentido, el presente texto señala la reinterpretación genética de dichos yacimientos, considerando las evidencias volcanogénicas, el volumen general de mineral que contienen, distribución y su importancia económica que tienen en la región central del Perú.

Nov 24, 1986

By B. Anameric, S. K. Kawatra, K. B. Rundman

The iron nugget process is an economical, environmentally friendly, cokeless, single-step pig iron making process. Residence time dependent process requirements for production of pig iron nuggets at a fixed furnace temperature (1425 C) were investigated. Three chemically and physically different products were produced after complete reduction to iron, depending on the residence time in the furnace. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets (PIN). The increase in the carbon content of the system as a function of residence time was detected by optical microscopy and Microhardness measurements. Sufficient carbon dissolution for the production of pig iron nuggets was obtained after 40 minutes residence time. The pig iron nuggets produced had chemical and physical properties similar to blast furnace pig iron. They were liquid state products and slag was completely separated from the metal.

Jan 1, 2005

By R. S. Dean

As set forth in the decision of the Trail Smelter Arbitral Tribunal, dated April 16, 1938 This Tribunal is constituted under and its powers are derived from and limited by the convention between the United States of America and the Dominion of Canada signed at Ottawa, April 15, 1935, duly ratified by the two parties and ratification exchanged at Ottawa, August 3, 1935 (hereinafter termed "the Convention") . . . The duty imposed upon the Tribunal by the Convention was to "finally decide" the following questions: (1) Whether damage caused by the Trail Smelter in the State of Washington has occurred since the first day of January 1932, and, if so, what indemnity should be paid therefor? (2) In the event of the answer to the first part of the preceding Question being in the affirmative, whether the Trail Smelter should be required to refrain from causing damage in the State of Washington in the future and, if so, to what extent? (3) In the light of the answer to the preceding Question, what measures or regime, if any, should be adopted or maintained by the Trail Smelter? (4) What indemnity or compensation, if any, should be paid on account of any decision or decisions rendered by the Tribunal pursuant to the next two preceding Questions? In this decision reported to the Government of the United States of America and to the Government of the Dominion of Canada, the Tribunal answered the first question in its entirety and reserved decision on the other three questions in accordance with the following extract from their decision

Jan 1, 1944

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Lars Richter, Franz-Werner Gerressen

"The Eglinton Crosstown Line was conceived as the Eglinton Crosstown LRT, a partially underground light rail line, announced in 2007 as part of the Transit City plan, which included the implementation of six other light rail lines across Toronto.There were 43 stops planned for the Eglinton Crosstown LRT, 13 of which would be underground . For those underground stations a lot of specialty foundation works needed to be carried out. King piles, soldier piles with lagging and secant piles were mainly required fulfilling the tasks of installing the retaining wall system.The paper will focus on the original design and alternative solutions, discussing the benefits and limits of these. It will also explain the installation process in general as well as some specific features related to specific site conditions, e.g. limits in installation depth, soil characteristics etc. The required equipment will be explained showing the benefits and limits.INTRODUCTIONThe Eglinton Crosstown project is a 19-kilometre LRT line that will bring much needed relief to the transit woes of Torontonians. Traversing the city in an east-west slice across the midtown artery of Eglinton Avenue, the Crosstown rail line involves a combination of 15 underground stations and 10 atgrade surface stops. It is one of the largest transit infrastructure projects under way in North America today. Aecon has joined partners ACS Infrastructure Canada, Ellis Don, and SNC-Lavalin to form Crosslinx Transit Solutions (Crosslinx).As with many of today’s mega public transportation projects, the Crosstown LRT follows the Public- Private Partnership (P3) model. Aecon is an equal partner in the $5.3-billion Crosslinx consortium to develop the Eglinton Crosstown LRT project in Toronto. Upon the LRT's completion in 2021, Metrolinx, the region’s transit authority and also the project client/owner, will turn to the Toronto Transit Commission (TTC) to operate it. The impact of this highly anticipated LRT line on commuters in the Greater Toronto Area (GTA) is expected to be dramatic and immediate once the first train leaves the station five years from now. In fact, Metrolinx is estimating that within its first 10 years of service, the Crosstown line will be carrying 5,500 passengers per hour (in peak direction) and making 100 million passenger trips annually."

Jan 1, 2017

The Bureau of Mines recognized the need for a demonstration program to distribute and apply existing information regarding the illumination of working places in mines. This report details the performance of illumination systems which were installed on several different types of mining machinery.

Jan 1, 1978

By S. Ripke

Between 2002 and 2004, the performance of a six million ton per year iron ore beneficiation plant dropped significantly. In a classic case of “who done it,” was it the mine, the concentrator, an ore change, or something else? While average annual final product grade decreased 8% (indicated by an increase in silicate gangue from 2.76% to 2.99%), the weight recovery also decreased by 8% (from 37.92% to 34.79%). This represents a loss of 832,000 tons of iron ore worth about $16 million for the two year period! The concentrator had been optimized to produce a high grade wet concentrate as feed to the dry side of the plant. But, did optimizing an individual unit operation’s grade give the best overall plant performance? In this paper, the investigation and solution to this mystery will be revealed.

Jan 1, 2007

By Maurizio Siepi

The realisation of most of the civil engineering works is subordinate to the execution of consolidation works, in order to improve the soil physical-mechanics characteristics. The works classifiable with the term "Soil Improvement" can be realised using several technologies, among which the Deep Mixing Method is distinguished for his remarkable flexibility and productivity characteristics. The Deep Mixing Method is a process whereby a rotary drilling machine mechanically drills a constant diameter hole while cement slurry is injected into the soil at high pressure. The process combines state of the art construction techniques merging mechanical and hydraulic mixing energies at the tool bit. The result is a soil-cement column of engineered strength, consistency and dimension. Whereby the soil cement column formation process is controlled by a computerised device, the result is a speedy installation, thorough mixing, and a high degree of control, repeatability and documentation.

Jan 1, 2002