Search Documents

By Barry T. Kilbourn

There is a continuous quest for better-performing materials, for example, to withstand higher temperatures, to resist more efficiently degradation or to be electrically conductive under extreme conditions. The oxides, and similar compounds, of the lanthanides and yttrium can, in some cases, help provide such behavior. Other advanced materials, such as hydrocarbon catalysts, optical ceramics or sensitive phosphors, may also require these oxides for some essential function. The role of the oxides in a wide variety of technologies, some novel and developing, will be reviewed and the underlying physico-chemical principles, the common threads, between several less well-known and apparently unrelated uses discussed.

Jan 1, 1989

By D. Nozadze

A new method of isothermal electro-contact diffusion welding of layered composites under pressure is offered. The scheme is developed and laboratory installation is created on which preproduction models of the layered composite of steel and aluminum is produced. A new method of electro-contact hot deformation is proposed for realization of diffusion welding by pressure of stratified blanks providing high-temperature isothermal process. In this case a rolling process or composite pressing is meshed with simultaneous electric current transmission in deformation center. Considering that a resistance of transient layer far exceeds the resistances of composite components, the heat release takes place intensively just in this layer. As the surfaces are approached over a distance of inter-atomic forces, the energy of boundary atoms easily reaches the energy threshold of capture with a formation of qualitatively new metallic bond. Proposed method, providing isothermal process in deformation center, excludes a necessity of previous preparation and prevention of surfaces. In this case strength of layer connection may approximate or exceed strength limit of cladding layer.

Jan 1, 2006

By Gerardo R. Alvear

The ability to efficiently remove impurities contained in concentrates is a key point to consider when selecting copper smelting technology for new plants or modernisation projects. Volatilisation of impurities such As and Sb should occur as early as possible in the process, and preferably in the smelting furnace, so that they do not impact on downstream unit operations. The ISASMELTTM process has been demonstrated to remove impurities efficiently, through high levels of volatilisation. This behaviour is promoted by attributes of the process such as the strong bath agitation, and the flexible nature of the process design, allowing the operator to choose the optimal matte grade for impurity partitioning, and the positive effect of the moisture content in the feed. This paper presents the distribution of minor elements in the copper ISASMELTTM furnace. Distribution impurities of As, Sb, Pb, Zn and Co observed in the ISASMELTTM furnace at Mount Isa Smelter are reported. Then, based on plant results and thermodynamic considerations, the potential application of ISASMELTTM technology for processing complex concentrates is discussed.

Jan 1, 2006

By Han Ilhan

This paper discusses and describes aspects of a cost effective and safe tailings impoundment selection. In light of the current low metal prices and recent tailings embankment failures around the world, it is becoming extremely more important to develop tailings impoundment design that balance cost efficiency with safety. The paper will present critical design components associated with a tailings impoundment which need to be addressed during the planning phase. Procedures for identifying various tailings impoundment alternatives, and evaluation and selection of alternatives are presented.

Jan 1, 1999

By O. Nakai

In the copper electrorefining process, the quality of the starting sheet is one of the basic factors for producing high quality copper cathodes. A highly automated and advanced facility for the production of copper starting sheets was constructed at the Toyo Copper Refinery in 1992, bringing various improvements into an automatic stripping system using stainless steel mother blanks. In 1998, the refinery expanded the tankhouse by another 128 commercial cells, and introduced 64 polymer concrete cells in a first stage conversion. As a result, the Toyo Copper Refinery now has the capacity to produce 103,200 t/y of cathode copper. Construction has led to great improvements in the materials handling facilities and computer associated short-circuit detection technology. This report summarizes the improvements made in the quality of the cathodes and in plant productivity.

Jan 1, 1999

By E. M. Timoshenko

Autoclave technology can be effectively used for liberation of complex mineral raw materials to transfer valuable constituents into solution for their subsequent recovery or to refine feed material in order to remove deleterious impurities, e.g. arsenic. The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs, high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: - Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); - Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially at the stage of liberation (chemical upgrading) of raw materials are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent).

Jan 1, 2006

By L. L. Ludwig, S. E. James, B. L. Motycka

Significant modifications to the electrolytic zinc plant operated by Big River Zinc Corporation were made at the end of the 1990's resulting in increased capacity and improved efficiencies. A new cell room, with the innovative use of acid-resistant concrete cells and a modern ventilation system, was installed to raise the capacity from 80,000 tonne/y to 106,000 tonne/y of finished zinc. Improvements to the leaching section include the conversion from a single to a two-step process, with associated equipment changes, to improve the quality of the residues produced. Another key change is the construction of a facility to allow the use of zinc oxides from secondary sources as a feed to the plant. This paper describes these improvements and the current operations.

Jan 1, 2000

By L. N. Ertzeva

The process for thermal treatment of current pyrrhotite concentrate in reducing environment with the use of disperse metal iron as an iron-bearing additive (optimal volume 20-30%), with downstream magnetic separation of the calcine, has been studied. The reduction process has been performed in conditions emulating those of both tube and fluidize-bed furnaces.

Jan 1, 2006

By K. Watling

Vibrational spectra of surface and solution compounds formed during cyclic voltammetry of a gold electrode in a deoxygenated 0.01 mol dm-3 NaCN solution have been examined using surface-enhanced Raman scattering (SERS) spectroscopy. The presence of cyanide at the electrode surface was indicated by Raman bands characteristic of the carbon-nitrogen stretch, CN.. Chemisorption of cyanide on the gold surface was evidenced by the presence of vibrational modes due to gold-carbon stretching, AuC, and gold-carbon-nitrogen bending, AuCN. Prior to the disappearance of the surface cyanide stretch band, a limiting value of the CN was obtained, the same as the value reported for adsorbed cyanide. Effects upon the voltammetry and vibrational modes of surface species due to additions of silver and lead to the gold-cyanide system have been observed.

Jan 1, 2003

By Daniel Gauthier, Patrick Sharrock, Cedric Verwilghen, Gilles Flamant, Ange Nzihou, Jocelyn Ramaroson

Clean processes are needed to dispose of many wastes. The incineration of 1 ton of municipal solid waste generates 6000 Nm3 of combustion gases contaminated with heavy metals and other pollutants. Gas scrubbing processes are required to clean incineration fumes in order not to transfer pollution to the atmosphere. We are investigating the use of Hydroxylapatite (Ca-HA) particles for use as sorbent for the removal of volatile heavy metals. We have carried out the synthesis of Ca-HA by two precipitation methods from solution and obtained solids with specific surface areas reaching more than 100 m2/g. Preliminary adsorption experiments were conducted in a horizontal furnace by mixing Ca-HA with 5% by weight of cadmium chloride in solid state. The mixture was heated to 600°C under air atmosphere during 6 hours. Chemical analysis of the solids confirmed that 85 % of the cadmium was retained in the solid phase. Such laboratory results showed that Ca-HA is capable of adsorbing cadmium chloride vapors, and pilot scale studies confirmed cadmium abatement in an industrial context.

Jan 1, 2008

By Anjali Talekar

Low temperature heat capacities of pentaerythritol [PE: C(CH2OH)4], pentaglycerine [PG: (CH3)C(CH2OH)3], and 2-amino-2-methyl-1,3-propanediol [AMPL: (NH2)(CH3)C(CH2OH)2]have been determined by adiabatic calorimetry from 3 K to 300 K. To the best of our knowledge, this is the first reported heat capacity measurement below 280 K for PE and AMPL. The Debye temperatures for these organic crystals have also been determined and compared with other alcohol derivatives of neopentane.

Jan 1, 2006

By K. Osseo-Asare

Rate laws for the hydrogen reduction of metal ions are typically of the form: [r = -d[M(II)]/dt = k[M(II)]xPy2H] where k is an apparent rate constant, [M(II)] and PH2 represent dissolved metal concentration and hydrogen pressure respectively, while x = 0 - 1 and y = 0.5 - 2. Half-order dependences have been reported for some M(II)/H2 systems; however, no satisfactory explanations have been offered. In an effort to bridge this gap in our understanding, the published precipitation rate data (for M(II) = Cu(II), Ni(II), and Co(II)) are reviewed (with emphasis on the reported reaction orders) and compared with the corresponding but limited electrochemical polarization data. Based on the available literature on the electrochemical kinetics of the M/M(II) and H2/H+ systems it is demonstrated theoretically that, under certain conditions (e.g., in the presence of electron-conducting solids), the rate of the M(II)/H2 reaction can be expressed as: [-d[M2+]/dt = k[M2+]2/1P2/12H] It is concluded that electrochemical processes probably play an important role in the hydrogen reduction of metal ions, especially for systems that involve heterogeneous catalysis.

Jan 1, 2003

By Vinod K. Namilakonda

In situ synthesis of discontinuously reinforced aluminum alloy metal matrix composites was investigated. Aluminum alloy (A356: Al-7 wt% Si) was reinforced with dispersed AlN particles. Thermodynamic calculations were made for the composition determination of various phases formed during bubbling of NH3 gas into the Al alloy melts in the temperature range 1173-1473 K. Experiments were carried out for in situ production of AlN particles with the reaction between Al melt and NH3 gas in high temperature resistance furnace at 1473 K. The products were characterized using SEM, EDS and XRD. Effect of bubbling time of NH3 gas on the AlN formed in the composites was studied. The amount of AlN reinforcement in the Al alloy composites was observed to be in the range of 5 to 35 wt%. Good agreement was observed between the experimental and thermodynamic calculated data on the composition of AlN in Al alloy composites.

Jan 1, 2006

By H. Roberts, C. Hassall

The opening years of the new millennium will be characterised by the closure of many lead and zinc mines because of reserve depletion. However, weak commodity prices through the second half of the 1990s have slowed project evaluation and have made it difficult to raise finances for the development of new mines required to replace lost output and to meet increasing demand for metal in the future. Growth of lead and zinc demand will be determined by the pace of global economic activity, especially in the emerging economies. How rapidly demand grows will have a key bearing on the possible shortfall in mine output and the response of prices to the implied tightening of metal supplies early in the new millennium. These issues are the focus of a discussion of the critical lead and zinc supply developments which will unfold post 2000, taking into account project lead times and the role that recycled metal plays in meeting market demand.

Jan 1, 2000

By M. A. Llavona

The study of the formation and components of copper patina and its conservation has assumed great importance. The changing environment has accelerated the processes of patinas degradation; thus, the exhaustive study of factors capable of affecting the patina formation, growth and durability has assumed great importance for the industrial activity of copper. The main components of the patina, oxides, chlorides, nitrates and sulfates, have been determined; the effect of physical, chemical and microbiological factors on patina formation, particularly the influence of acid rain, natural organic matter, particles and microorganisms have been defined. The effect of different electrolytic solutions that accelerate the formation of copper patinas has been determined, and a review of the state of knowledge of the formation and evolution of metal patinas has been made.

Jan 1, 1999

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By B. J. Beaudry

The effect of various levels of purity of the rare earth fluorides and the calcium reductant used to prepare rare earth metals were determined. Metals which have low melting points such as La, Ce, Pr and Nd are not purified by distillation or sublimation. Impurities in the reactants remain as contaminants in these metals. Gd, Tb, Y and Lu which have slightly higher vapor pressures at their melting points than the first four metals are usually distilled to remove the Ta or W impurity introduced by the crucible and are purified slightly with respect to 0 and N by distillation. Rare earth metals that have high vapor pressures such as Sc, Dy, Ho and Er can be purified with respect to 0, N, C, as well as Ta or W by sublimation. The most volatile rare earth metals Sm, Eu, Tm and Yb are readily purified by sublimation and are usually prepared by a reduction-distillation process directly from the oxide. The importance of each step of the processes in determining the final purity of the individual rare earth metals is discussed.

Jan 1, 1989

By Romeo U. Pagador

After privatization in 1999, PASAR Corporation initiated a plant modernization program to optimize the performance of the smelter by increasing plant availability. This initiative required operational adjustments to the converting and anode furnace procedures, to support the higher throughput in the flash furnace, while continuing to meet government environmental regulations. The major shift in production direction was to eliminate the 30-35 day maintenance shutdown every two years, and replace it with a 15-day shutdown. This paper discusses the changes implemented in the converter and anode operation that have resulted in an increase of 10% in flash furnace throughput, an 18% increase in blister output, to 170 tonnes per cycle, and a converter campaign tonnage increase of 10%. Since privatization, PASAR has instituted a series of ?management of change? programs that have facilitated an industrial cultural change needed to achieve the company?s vision, mission and strategic goals.

Jan 1, 2005

By R. Togashi, S. Kuramochi, T. Yamada

In 1972, the Akita Zinc Co., Ltd. commenced operations with an annual capacity of 86,000 tonnes of electrolytic zinc, and it has operated with an annual capacity of 156,000 t-Zn since 1974. The business surroundings for non-ferrous metals production have become more severe with the high Yen rate for the dollar and low domestic demand in the last few years. Consequently, the company tried to survive with some improvements and succeeded to reduce operating costs and to improve profitability as follows: 1) expansion of its production capacity to. 196,000 t-Zn annually, 2) saving man-power by the introduction of fully-automated machines for cathode handling in the cellhouse, 3) improvement of the hematite process by means of the recovery of rare-metals. These improvements made Akita Zinc a competitive refinery in the modern world. We have been trying to improve the operations more and more. One of the challenges is to purify the iron oxide made in the hematite process by applying an As removal process, which is coming into operation in the near future.

Jan 1, 2000

By G. Ríos

Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975 the old blast furnaces were replaced by the Outokumpu FSF technology. During the last 30 years, through several expansions and technical modifications, the production has increased up to 300,000 tpy of new copper. This paper describes the developments on the control of impurities that have been made to fit new situations, such as a new artificial gypsum plant, a new electrolyte treatment plant or different secondary materials handling management.

Jan 1, 2006