Search Documents

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By J. M. Girard

Ground control problems at surface mining operations can occur for a variety of reasons. Stress, gravity loading, rock strength, geology, pore pressure, weather effects, underground workings, and many other factors contribute to slope instabilities that range from small rock falls to massive slides of material. While some of these failures can he predicted or controlled by preventive measures, each year many completely unexpected failures occur. Current methods for monitoring generally involve measuring displacements at a few, selected points in and around the suspected area of instability. While most of the displacements along these points will be in a downslope direction, freeze-thaw cycles of water-filled joints, horizontal stresses or pressure, buoyancy in saturated soils, human measurement errors, or other situations can produce deformation in almost any direction, even without any instability in the slope. Determination of which, if any of the observed movements represents a potential hazard is essential.

Jan 1, 1998

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term "burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the futures of high frequency, great strength and shallow depth of the beginning burst have been found. There ere some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003

By Klaus Opolony

The German coal industry operates a multi-seam extraction system, with average working depths currently around 1,000 meters. The gate roads serving the longwalls are often used for a second time - a practice which has the advantage of allowing several panels to be extracted with a minimum of roadway drivage work. This preference for re-using gate roads is based on a number of factors: such an arrangement a) prevents the strata pressures in the subsequent panels from being adversely affected by the presence of support pillars, b) helps achieve the target of full mineral extraction and c) allows the roadways to be used for air conditioning and ventilation purposes as part of an advancing longwall system. This paper explains the planning procedure required for a rectangular rockbolted roadway, using as an example a gate road in the 3 meter-thick D2/C seam at Lippe colliery, and describes the subsequent operating experience. Here special attention is focused on modem procedures and techniques for mine roadway planning. The investigation also examines the part played by the mine ventilation system and the available machine technology, which are particularly important parameters for the design of the T-junction areas and support system. Keywords: multiple seam extraction, longwall mining, roadway drivage, roof bolting, roadside pack system, hydraulic frame type support.

Jan 1, 2002

By Laxminarayan Holla

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

Virtually all mineable Appalachian coal seams exist in a multi-seam environment. This makes it inevitable that most seams will eventually experience interaction induced ground control and mining problems. Indeed, it has been estimated that every working face will experience interaction effects from previous or current workings at least once during its lifetime (1), and that these problems are considerably exaggerated when seams are in close proximity -- a distance of less than 110 feet. The continued increase in multi-seam problems has resulted in considerable research activities over many years (2,3,4,1). Theoretical analysis, numerical and physical model studies, statistical and empirical analysis of numerous interaction related field data have been applied to multi-seam mining situations and have identified many useful trends and design criteria (4,5,6,7). To fully utilize research results and transfer multi-seam mining technology to field engineers, a design model -- USEAM was constructed (8). This model, designed for close seam under-mining situations, was computerized to facilitate utilization. In the current research, a new computer program "MSEAM" was developed to produce a model for both under- and overmining close seam situations. It is hoped that both of these software packages will aid field engineers in using important interactive design criteria to gain a better understanding of interaction mechanisms. Through advance planning with these programs, detrimental interaction may be avoided and minimized, and occasionally a design can be selected which will allow interaction effects to be utilized to the benefit of mining operations.

Jan 1, 1987

By R. J. Morrell

The Bureau of Mines developed a ground support system for use with an underground coal auger. The system consists of inflatable airbags that are inserted in the holes as they are drilled, and then gradually deflated to provide controlled roof caving. This paper presents results of laboratory and field tests of the system that show it to be technically feasible.

Jan 1, 1988

By Alan Peacock

Shield supports have been in use in the USA underground mines since 1975, and their development in the intervening time has been progressive and inovative. Specialized techniques are used to optimize their performance in a particular application and to design the component parts.

Jan 1, 1981

By H. N. Maleki

Extensive measurements and underground observations in three Western U. S. coal mines are integrated in this paper to determine in-situ pillar load-deformation characteristics for narrow (30 it wide, 80 ft long) pillars in two-entry gate road systems. In spite of similarities in the regional geology, coal pillar laboratory mechanical properties and gate pillar geometries, the pillar peak strength, post-failure behavior, and failure mechanism were shown to be significantly different. Pillar peak strength was shown to be dependent on depth at one site, approaching burst-prone stress levels of 4000 psi. At another site, the pillar peak strength was lower because of lower confinement; this was related to the higher frequency of cleats and the lower friction- al properties of the roof/floor and coal contact. Two failure mechanisms were identified - one in the pillar, and the other in the mine floor. The roof stability was good at all three sites because of the thick-bedded nature of the roof strata and limited total gate span in a two-entry system. Existing pillar design techniques were shown to be inadequate for design, requiring adjustments for depth of cover, cleat frequency, and roof /floor frictional properties.

Jan 1, 1988

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

By Bruce Hebblewhite, Jim Galvin

"A coal burst occurred on 15 April, 2014 at the Austar Coal Mine, located west of Newcastle, NSW, Australia. The burst resulted in fatal injuries to two men working as part of the mining crew at the development face. At the time, a continuous miner was being used to mine a longwall development gate road through heavily structured coal, at a depth of approximately 550m. A number of pre-cursor bumps had occurred on previous shifts, emanating from the coal ribs of the roadway, in proximity to the coal face.This paper reviews the geological, geotechnical and mining conditions and circumstances leading up to the coal burst event; and presents and discusses the available evidence and possible interpretations relating to the geomechanical behaviour mechanisms that may have been critical factors in this incident. The paper also discusses some key technical and operational considerations of ground support systems and mining practices and strategies needed for operating in such conditions in the future.INTRODUCTIONAustar Coal Mine is an underground longwall coal mine located near Cessnock in the Hunter Valley of New South Wales (NSW), Australia and is the only underground mine still extracting the Greta Seam in this region. The mine was the first in Australia to adopt the Chinese-developed Longwall Top Coal Caving (LTCC) method for thick seam extraction. Typically seam thickness ranges from 4m to 7m and depth of mining from 480m to 560m, with future mining planned down to depths of up to 700m, making it one of the deepest operating coal mines in Australia.On 15 April 2014, a pressure burst occurred in the left hand rib at the active mining face of B Heading, 2 to 3 cut-through, Maingate A9 panel, during development of the gateroads for the ninth longwall top coal caving panel. Strata in the general vicinity was affected by disturbed geology and multiple geological structures. Figure 1 shows a section of the mine plan as at October 2014 (six months after the accident), indicating the current longwall extraction panel (AS) and the development panel A9 where the accident occurred. (Note: Neither development nor longwall face positions changed significantly between the time of the accident and the date of this plan). At the time of the accident the current longwall face was in excess of 1,000m away from the Maingate A9 development panel face position."

Jan 1, 2016

By Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (l) study the interaction between MRS's and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS's have capacities of 5,340 and 7,120 kN (600 and 800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS's help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-scam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4) geologic structures, and (5) panel layout designs and mining practice. Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts ate needed.

Jan 1, 2001

By Anil Mahyera

Under contract to the Bureau of Mines, a roofbolting machine has been developed which will: control torque on the bolthead to within 4 percent of a set point, control thrust to a low level (150 lbf), and implement a tightening method to minimize variability due to bolt tension decay of a group of bolts caused by differing anchor creep rates. This bolter was used to determine bolthead and thread friction factors, and to determine the effect of adding a hardened washer to the bolt assembly on the uniformity of bolt tension in the laboratory and field. Recommendations for torquing speed, bolt lubrication, use of hardened washers, and thrust level on the bolthead are made. The relationship of this system to Improved roof control is discussed, along with additional work that remains to be performed. Patent Notice Patents are pending which protect the hardware and methods of controlling tension decay as discussed in this paper.

Jan 1, 1981

By L. Munsamy

The bulk of primary mining at the Anglo Coal's Bank Colliery was carried out by drill and blast method, in a bord and pillar layout exploiting the No. 2 Seam. Secondary extraction, top/bottom coaling, also took place using both the drill and blast (D&B) method and continuous miners (CM). Extensive mining in this seam resulted in the risk of sterilising the No. 4 Seam reserves. Therefore, multiseam design guidelines established by Salamon and Oravecz (8) were re-evaluated in light of the low safety factors and the low pillar width to mining height ratios of pillars in the No. 2 Seam. Two and three dimensional (2D & 3D) numerical modelling was carried out to quantify and verify the parameters that influence the multiseam mining. The modelling was conducted primarily in two dimensions (plane strain), with 3D models to confirm the validity of the 2D results. A panel risk assessment flow chart was developed to assess the panels with respect to pillar failure and multiseam mining. This flow chart was extended into the evaluation of risk of surface subsidence using the current rock engineering knowledge. The aim of this risk assessment tool is to assess all underground workings at Anglo Coal collieries simply and rapidly. The identification of high-risk areas would warrant further investigation and possible backfilling to reduce the risk of pillar failures ensuring that reserves in the No. 4 and 5 Seams above are intact.

Jan 1, 2004

By Douglas C. Peters

Part of the ground control research at the U.S. Bureau of Mines is involved with improving ground control data collection and analysis methods. A geographic information system (GIs) is being used within this research effort to standardize the data collected and provide a common graphical and tabular format and analysis system for researchers to access information on underground coal mines. In addition, GIS's can perform relational analyses on multiple map and tabular data sets which are not possible through map-creation or CAD packages or through data bases alone. In addition to standardizing ground control analyses, there is an increasing need for rapid analysis of ground control data in connection with increasing production rates at longwall mines. The examination of a large number of interrelated parameters and their impact on short-term mine safety and productivity under the time constraints imposed by rapid production requires computer-aided techniques. A GIs provides the means to quickly, quantitatively, and reproducibly evaluate mine-wide conditions. This overview of GI8 techniques for mine data integration and analysis, using a mine in Colorado as an example site, will cover the input of data into a GIs, including mine-wide monitoring system data and general data such as roof control plans and geology. The methods to geographically reference these data sets and retrieve and combine them also will be covered. Automation of such processes briefly will be reviewed to allow future users to automate their mine data analyses.

Jan 1, 1990

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

By S. Paul Singh

The implications of blast damage are harmful in both economic and physical sense. To understand the mysterious nature of blast damage assessment and prediction, field work was done by driving an experimental tunnel in the bench of a quartzite quarry. On the basis of the blast vibration monitoring records, a model was developed to predict the PPV at different distances from a blasthole. Critical particle velocity for damage and the output of the prediction model were used to delineate the extent of damage for different explosives. The predictory model was tested by designing a special blast and the burdens for the back holes have been recommended. The relationship between the critical particle velocity for "Fall Off' and the critical particle velocity for damage has been established. The existing criteria for blast damage have also been renewed in this paper.

Jan 1, 1993

By Zhanjing Yu

In this paper, an equation is developed to characterize the relationship between the UBC and plate size using a boundary integral approach. The equation was validated by the results from mo& than seventy (70) plate loading tests of different sizes conducted in various underground coal mines throughout the Illinois Coal Basin. The equation indicates that the UBC decreases as the plate size increases. The fundamental solution for this boundary integral problems is the Boussinesq equation. The load exerted by the plate on the floor surface is assumed to be uniformly distributed. Both normal and tangential loads are considered. It is also assumed that the floor fails in shear in a plate loading test. The equation may provide the mine operators with a useful tool to obtain from a plate load test of any plate size the UBC value required by the regulations.

Jan 1, 1993

By K. F. Unrug

A new testing technique for the determination of the rock strength from portable rock tester is proposed. It is a quick and economical method that can determine the rock strength with reasonable accuracy in different conditions. This method is based on the application of portable rock tester working at the principle of forcing steel ball into the rock surface. The correlation between laboratory measured compressive and/or tensile strength and rack tester reading has been determined in terms of the three-controlling parameters: (1). diameter of indentation &'the testing sample, (2). diameter of indentation-on the reference bar, (3). Brine11 hardness number of reference bar.

Jan 1, 1990