Search Documents

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By S. Que

Local community acceptance is a key aspect of planning and managing mining projects, whether through sustainability assessment and reporting or corporate social responsibility programs. However, there has been very little research to understand the determinants of community acceptance. This paper seeks to identify key mine characteristics and demographic factors that influence individual acceptance of mining projects. Six demographic factors and 16 mine characteristics were selected based on literature review. Four of the six demographics factors were confirmed to be significantly (p < 0.05) correlated with people?s attitude of the importance of the mine characteristics. All sixteen mine characteristics are identified as important factors. The most important mining factors are Job opportunities, water shortage or pollution, air pollution and land pollution. Both the mining and control groups have same opinion of 12 mining characteristics and differ on four (infrastructure improvement, labor shortage for other businesses, noise pollution, and mine life). During design and management of mines, this data can be used as a reference. This result will facilitate better choice experiment (survey) design for discrete choice modeling. Such discrete choice models can provide a viable framework for data-driven community engagement and sustainable mine management.

Feb 23, 2014

By C. S. Simons

The aphorism that provided the title of this paper is probably a couple of hundred years old, but it still expresses a fundamental truth in the metals industry. This truth will be illustrated through a brief review of the major developments in the extractive metallurgy of the oxidized ores of nickel - the "laterite" ores. While the details to be discussed are for the most part specific to nickel, a close parallel with other commodities - particularly in recent years - will be apparent even to those whose interest in nickel itself is slight. Thus it is hoped that this paper will be stimulating, at the least, to anyone who is concerned with the implementation of process improvement, "Invention" in the present context means any change from "conventional" process technology that shows a reasonable chance of reducing costs, increasing revenues, or both, in the production of a commodity. This can be anything from a simple rearrangement of flowsheet steps to a completely different basis for processing. And the result may reduce costs by more efficient use of energy or labor or reagents; may increase revenues by better recovery of the primary product or by introducing the recovery of previously ignored by-products; may insure sales volume (and thereby cash flow) through higher product purity or an improved product form. "Necessity" is the perceived need to attain at least one of these classes of results. This perception of necessity, however, varies widely from management to management and from project to project.

Jan 1, 1983

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By David W. Wisecarver

The U.S. Bureau of Mines, in cooperation with U.S. Borax and Chemical Corporation and the Kennecott Copper Corporation, has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of microseismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron Mine near Boron, California, and the Rimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nevada. Microsesimic noise rates in stable inactive mining areas are between 0 and 10 noises/ hour; the rates in stable active mining areas are between 10 and 50 noises/hour; and the rate in unstable areas is as high as 2500 noises/ hour. High microseismic noise rates in the Liberty Pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic tech¬nique is applicable to large pit walls, and that the wide band, wide range microseismic equipment appears to be suitable for open-pit investigations.

Jan 1, 1969

By Zhonglin Ye, Guangping Dai, Ba Zhang, Yonggang Wei, Shiwei Zhou, Bo Li, Hua Wang

Decreasing copper content in slag is critical for improving copper recovery, where apparent viscosity is the main factor affecting the separation of matte/copper from the slag. The viscous behavior of copper converter slag was investigated during reduction process in this paper, and its non-Newtonian viscous behavior and shear thickening characteristics were clarified. The effects of silicate structure and solid particles in the melt on the slag apparent viscosity were investigated. As slag cleaning proceeded in an electric furnace, the magnetite gradually transformed into ferrous oxide, increasing the FeO/SiO2 ratio. With this ratio increased from 1.2 to 2.0, the slag structure was simplified, and its apparent viscosity decreased from 0.26 to 0.12 Pa·s at 1523 K. The iron phase was excessively reduced to metallic state; the slag contained metallic copper-iron alloy particles, increasing apparent viscosity. The apparent viscosity and phase structure of the slag corresponding to the iron phase reduction process were analyzed in detail; the results obtained in the present study are of great significance to the reasonable control of the converter copper slag cleaning process.

Nov 7, 2022

By P. H. S. W. Kulatilake, T. Hudaverdi, C. Kuzu

Prediction of blast fragmentation plays a key role for overall productivity of mines. In this study, a new multivariate analysis procedure for prediction of blast fragmentation is presented. Several blasts performed in various mines and rock formations worldwide were brought together and evaluated. An extensive blast database was created. Blast design parameters, the modulus of elasticity and in-situ block size were considered to perform multivariate analysis. A complete multivariate analysis procedure was applied in three steps. First, a hierarchical cluster analysis was used to separate the blast data into different groups of similarity. Two different groups were formed based on the elasticity modulus values. In the second step, group memberships were checked by discriminant analysis. The dominant parameters of the occurrence of the groups were determined. Also, discriminant analysis was used to determine the group membership of the respective blasts. As the last step, the multivariate regression analysis was applied to develop prediction equations for estimation of the mean particle size of muckpiles. Two different prediction equations were developed based on the rock stiffness. Validation of the proposed equations on various mines was performed. Prediction capability of the proposed models was found to be strong. The models are not complex and are suitable for practical use at mines.

Jan 1, 2011

By S. A. Shoop

Vibrations from thirty-seven blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations reported in the U.S. Bureau of Mines studies. Regulations based on USBM data could then be too conservative or lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1983

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By Maurice L. Madden

An investigation was undertaken for a ground water discharge plan for the Chino mining complex near Hurley, New Mexico. Operations which impact ground water include dump leaching, storage reservoirs, and tailings seepage. The investigation included both hydrogeological data collection and laboratory analysis. A conceptual understanding of surface water and ground water was then developed. Surface water and ground water models were used to match existing conditions and predict the impact of operational modifications. The study concluded that runoff and resulting leach reservoir overflows were primarily responsible for the ground water degradation. Tailings seepage represents a smaller part of the impact.

Jan 1, 1984

By Ingunn Opland, Silje M. Tinderholt

Drill and blast project in Norway’s capital. The contract consists of 7 rock caverns (350–950 m2), 9.2 km tunnels, and four shafts. With 110 blue-collar and 31 white-collar, the project produces an average of 16–21,000 m3 hard rock per week, with a total of 19 tunnel faces. Weekly, nine grouting rounds for water control, 800 m3 shotcrete, and 1,200 bolts are required, and 60 trucks leave the site pr. day. Challenges include blasting in densely populated areas, planning and coordination to maintain high production, obtaining a CEEQUAL certification of very good, and transporting rock on Oslo’s main highway.

Jun 13, 2023

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By O. Ofor

Coal fines of less than 0.5 mm particle size, discarded as too fine for gravity separation, were subjected to flotation tests at varying pH and temperatures using modified dosages of kerosene as oil phase and methylisobutylketone (MIBK) as frother. Optimal coal recovery of over 74% was obtained using 200 kg kerosene and 4 kg MIBK per ton of coal fines at a pH of 9.7 and an ambient temperature of 26° C. The coal concentrate obtained under these optimal recovery conditions assayed 9.10% ash, 0.35% sulfur and 0.011% phosphorus, representing reductions in the ash, sulfur and phosphorus contents of approximately 75%, 43% and 8.3%, respectively. Its gross calorific value was 32.9 MJ/kg, its percentage of volatile matter measured 30.6 and the fixed carbon content was 66.3% (d.a.f). Caking tests showed the optimal concentrate has a standard welling number of 1 and is a Gray-King coke type C. These results show that the optimal flotation product could be utilized for such industrial purposes as steam raising or for processing in gasworks, but it would be unsuitable for metallurgical coke production.

Jan 1, 1993

By C. Hansen, J. Killey

This paper discusses the replacement of AEROFLOAT ® 1 25 promoter by AERO ® 5688 promoter at Sonora Mining Corp.&apos;s California Mother Lode concentrator. Flotation concentrate is trucked 120 miles to a leach plant in Nevada, so the reduced mass resulting from higher gold grades and reduced talceous gangue and barren pyrite resulting from this change in promoters has brought about a major decrease in shipping costs. Preliminary laboratory testing indicated that free milling gold and controlled amounts of pyrite could be floated using Aero 5688 promoter with reduced dosages of Aero 350 xanthate.2 Extensive plant trials confirmed that the new reagent suite could indeed maintain gold recoveries while reducing total mass. Improved froth characteristics also improved operating flexibility in treating various ore types, and overall reagent costs have been reduced.

Jan 1, 1991

By W. K. Katoto

The Tailings Leach Plant (TLP) of the Zambia Consolidated Copper Mines Ltd at Nchanga was commissioned in 1974 as the world&apos;s first largest successfully operated agitation leach SX-EW plant for copper production. The design, development and operation of the plant soon after commissioning termed as TLP stage II has been described by Holmes et al (1). In the initial phase the plant was designed to treat approximately 25,000 tonnes per day of current flotation tailings from the Nchanga Concentrator operations, and had a design capacity to produce 75,000 tonnes per annum of copper. Further expansion took place in 1986, and TLP stage III was successfully commissioned to treat an additional 20,000 -25,000 tonnes per day of large reserves (over 135m tonnes) of reclaimed tailings stockpiled since the early 1930&apos;s in four paddock type tailings dams (T01 to T04). The salient feature of TLP stage III expansion described by S K Mwenechanya et al (2 -3) was the installation of the world&apos;s largest Horizontal Belt Filter Plant with 26 filters each of 80 m2 filtration area.

Jan 1, 1996

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992

By Ronald R. Bauer

Wollastonite is a little known industrial mineral of the silicate group. The largest and purest known deposit in the free world is being mined and beneficiated in Millsboro, New York by NYCO, A Division of Processed Minerals Incorporated. The associated garnet and diopside are separated from the wollastonite using dry high intensity magnetic separators. Beneficiated wollastonite is used extensively as an additive and filler in the ceramic, paint, refractory, and wallboard industries. Wollastonite acts as a functional filler due to its unique chemistry and physical acicularity.

Jan 1, 1982

By Patrick Sullivan

Over the past few years, successful operations for processing phosphates employing the Grate-Kiln System have been achieved. Control and instrumentation philosophy followed in these installations are described and analyzed. Concepts utilizing digital techniques and computer systems appropriate for similar installations are also discussed.

Jan 1, 1967

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983