Search Documents

By H. C. Fuller

Depletion of iron ore in the Nation's large deposits has directed attention to other sources. One of these is the titaniferous iron ore of the Iron Mountain, Wyo., area. Tests were made to determine the feasibility of smelting this ore, which contains about 20 percent titanium dioxide (Ti02), in an electric-arc furnace to produce pig iron. Initial tests, which were made in a 30-pound-capacity induction furnace, demonstrated that the iron could be easily reduced to metal and that limestone was a suitable and effective flux. Larger scale tests then were made in a 50-pound-capacity electric-arc furnace to obtain the more detailed information necessary for the planned continuous operation of a still larger arc furnace. The principal facts determined by preliminary batch-smelting studies were that (1) 9 pounds of limestone flux was required for each 100 pounds of ore smelted, (2) expensive coke was not required because coal proved to be a satisfactory reductant (near stoichiometric carbon was optimum), and (3) overreduction, which produced a viscous slag, must be avoided.

Jan 1, 1961

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By J. M. Stuve

Standard heats of formation (AH°p) of YbCl3 (c) and TmCl3 (c) were measured by solution calorimetry. Heat of solution data are given for ytterbium and thulium metals and corresponding anhydrous trichlorides in 4.360 molal hydrochloric acid. The derived standard heats of formation of YbCl3 (c) and TmCl3 (c) were -229,370 ±720 and -235,820 ±400 cal/mole, respectively, at 298.15° K. The resulting heats of formation for YbC13 and TmCl3 are about 1 kcal and 6.3 kcal more negative than previously published values.

Jan 1, 1967

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By Gerald W. Elger

The Federal Bureau of Mines developed a modification in the conventional Kroll process for preparing high - purity hafnium metal . This modification involved the partial replacement of magnesium by sodium in the batch reduction of purified hafnium tetrachloride to sponge metal . The raw tetrachloride was purified either by thermal degassing of the volatile contaminants to the atmosphere or by fused- salt treatment . In the fused- salt treatment , the tetrachloride was contacted with molten alkali chlorides to remove the impurities . The reaction byproducts were removed from the metal by heat treatment in an evacuated furnace . The metal sponge was consolidated by melting into buttons or ingots , which were analyzed for impurities . The purity of the metal prepared by the modified process is superior to that of the metal produced by the conventional method . The hafnium metal was comparable to crystal - bar hafnium except for the oxygen content , despite the abnormally high impurity concentrations in the raw tetrachloride . Several ingots were successfully cold - rolled to sheet .

Jul 1, 1960

By Milford L. Skow

Utilization of domestic ores in the winning of metallurgical alumina requires a convenj.ent method of treating siliceous bauxites and other aluminous materials. In the United states there are only small reserves of high-grade bauxite but considerably larger tonnages of low-grade material. In addition, there are large deposits of high-alumina clays. If these high-silica bauxites or high-alumina clays could be beneficiated, either by are dressing or by chemical dissolution to remove a large proportion of the silica, then the potential reserves of aluminum ores would be increased materially. Faced with a similar situation, the German industry, chiefly dependent on high-grade French bauxites prior to World War II, was compelled during the war to Use lower-grade ores. For desilicating the lower-grade bauxites before the Bayer treatment, a method was developed in which the bauxite was calcined and then given a dilute caustic leach preliminary to the pressure digestion. It was planned to regenerate the caustic by treatment of the desilication liquor with lime. As European bauxites are mineralogically different from those found in this country, preliminary work was undertaken to determine whether this process might be applied to domestic materials. The results of this work, along with a review of the German process, are presented in this report.

Jan 1, 1950

Spectrochemical methods were developed to determine beryllium in the concentration range 0.0015 to 4.0 percent in siliceous mineral beneficiation products. Two methods are described. They are (1) a fusion-pellet-spark procedure (spark method) and (2) a sustaining alternating-current arc procedure (arc method). In the spark method the sample is fused with lithium tetra-borate and vanadium pentoxide. The resulting bead is crushed, mixed with powdered graphite, and briquetted. This is analyzed spectrographically using controlled high-voltage spark excitation. In the arc method the sample is diluted with germanium metal, graphite, and vanadium pentoxide. Weighed charges are packed into cupped graphite electrodes and subjected to excitation with a sustaining alternating-current arc. Vanadium serves as internal standard for both methods. Effects due to matrix variations in samples and standards are eliminated either by fusion with lithium tetraborate in the spark method or by dilution with germanium and graphite in the arc method. Beryllium determinations show deviations from accepted chemical values of approximately 5 and 8 percent for the spark and arc methods, respectively. Analyses can be made more rapidly by the arc procedure with a sacrifice in precision and accuracy. Either method can be applied to the determination of beryllium in silicate rocks.

Jan 1, 1962

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

By B. T. McClure

Oxidizing catalytic converters are sometimes used by underground mine operators as an emission control device to reduce odor, hydrocarbon (HC), and carbon monoxide (CO) emissions from diesel equipment. The objectives of this report are to quantitatively assess the effects of catalytic converters on diesel exhaust emissions and to make recommendations for their use. Information in this report is from a literature survey and contract research supported by the Bureau of Mines. Catalytic converters are effective in reducing CO, HC, and odors when the exhaust temperature is high enough so that the converter remains above 250° C. Converter temperature is dependent upon engine duty cycle. Catalytic converters increse sulfate emissions and slightly in- crease oxides of nitrogen (NOx) emissions. If low sulfur fuels are not used, the increase in sulfate and nitrogen dioxide (NO2) emissions can offset any advantages of the catalytic converter as measured by the emissions quality index (EQI). In addition, in vitro bioassays have shown that catalytic converters produce soluble organic compounds, which have increased mutagenic activity with respect to untreated exhaust. Based upon criteria recommended by a joint Canadian-United States research panel, catalytic converters should only be used in special circumstances in underground mines. Vehicles equipped with catalytic converters should operate under moderate to heavy load conditions, and use fuel with a sulfur content less than 0.1 pct.

Jan 1, 1988

By S. P. Kinney

During 1925, at Holt, Ala., the United States Bureau of Mines made a study of the composition of the gases at four elevations in the shaft of a furnace producing foundry iron. A report3 of the work was published in 1927. Some of the results of this investigation are shown in Figure 1. As indicated, the gas at the center of the shaft is low in CO2 content, while the gas in the vicinity of the wall is higher in CO2. The composition of the gases at the top and at the center of the stock column was not far different from the composition of the gas at the top of the bosh. The investigation indicated clearly that lean gas was channeling through the center of the column. More recently the study was enlarged in scope to include investigation of a furnace operating on Lake Superior ores in the Chicago district. A series of planes between the stock line and tuyères was surveyed. Means and apparatus were developed for obtaining, between the inwall and the center of the furnace, the gas composition, gas velocity, and temperature on each plane. A complete report4 of the investigation has recently been published.

Jan 1, 1929

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By William H. King

The Mercur Dome mine is in the Camp Floyd mining district, Tooele County, Utah (fig. 1). The property lies between 6,000 and 8,000 feet altitude on the southwesterly slope of the Oquirrh Mountains, a short distance west of Mercur, the district settlement. Mining began in the Mercur area in 1870. Operations at the Mercur Dame mine were started in 1937 after several claims had been consolidated into one group. Preliminary examination of the ground by F. H. Gunnell, a Bureau of Mines engineer, disclosed the presence of vanadium in a carbonaceous shale horizon. Rocks near the Mercur Lame property are chiefly sediments of Carboniferous age, including the Madison and Deseret limestones. The main shaft penetrates the Deseret formation to a point a few feet above the 1,000-foot level where it enters the Madison limestone. The flat-lying vanadiferous shale horizon is exposed on the 1,000-foot level near the top of the Madison limestone. The Bureau of Mines development program, consisting of diamond drilling, auger hole drilling, and sampling, was planned to determine the extent and assay value of the vanadiferous bed. Seven diamond-drill holes totaling 300 feet were drilled from the 1,000-foot level of the mine. Eight hand auger holes were drilled in the back of the drift on this level (fig. 2). Assay determinations were made on 74 samples from the drill holes and supplemental channel samples and are tabulated in this report. The concluding section embodies results of metallurgical tests.

Jan 1, 1949

By L. A. Stewart

"SUMMARYThis paper describes most of the chrysotile-asbestos deposits of Arizona. Mining methods are discussed briefly and asbestos-mill flowsheets are incorporated. Arizona asbestos mines are the only sources on the American continents of naturally iron-free chrysotile spinning fiber that is so urgently needed for electric-cable coverings, especially on warships.Asbestos was first recorded and recognized in Arizona in 1872, and a minor amount was produced from a deposit in the Grand Canyon in 1900. The discovery of a deposit in the Salt River district in 1912 initiated intensive prospecting, and deposits soon were developed. The total Arizona production of all grades of asbestos through 1953 is estimated at 30,000 to 35,000 tons.The deposits of the Central Arizona region, which are discussed in this paper, are scattered over nearly 2,000 square miles. The annual output is relatively small, because the asbestos occurs in thin, discontinuous veins and only in areas where intrusions of diabase are adjacent to or crosscut certain favorable units of the pre-Cambrian Mescal limestone. This stratigraphic limitation, combined with other essential geologic conditions, tends to restrict the size of the deposits.Virtually all of the deposits are in rugged, mountainous country, and many of the mines are on steep canyon walls. In the average mine, production of 1 ton of commercial asbestos requires removal of 30 to 40 tons of waste rock. Mining and transportation costs consequently are high.Several deposits of chrysotile that is somewhat harsh and of moderate tensile strength have been known for years but were not worked because of the former exacting demands of industry for high-strength, soft asbestos. However, improve¬ments in asbestos fiberization and spinning technique, combined with the urgent need for asbestos, have made this so-called semisoft fiber desirable, and deposits of this type now are being exploited."

Jan 1, 1955

By Efrem R. Reeves

Noise-induced hearing loss (NIHL) is the most common occupational illness in the United States, with 30 million workers exposed to excessive noise levels [NIOSH 1996] every day. Of particular concern is the mining industry; which has the highest prevalence of hazardous noise exposure of any major industry sector [Tak et al. 2009] and is second only to the railroad industry in prevalence of work-ers reporting hearing difficulty [Tak and Calvert 2008]. This document is for operators, safety personnel, and mechanics in the mining industry who are not specialists in noise control engineering or acoustics. Evaluations of successful and unsuccessful attempts at controlling noise on several large, underground metal mining machines are detailed to illustrate the basic principles of noise control. Once personnel understand the guidelines and principles of noise control, they will be able to ¦evaluate the extent of a noise problem; ¦determine the best approach to the problem; and ¦apply the most appropriate solution. Because of the insidious nature of NIHL, it can go unnoticed until a considerable loss of hearing has occurred. In some cases, diagnosis is delayed because an exposed individual claims to have become accustomed to the noise. In reality, that person may have already suffered irreversible hearing loss. Humans can hear sounds in the frequency range from about 20 to 20,000 Hertz (Hz). Within this range, NIHL usually begins in the frequency region around 4,000?6,000 Hz, the upper levels of the speech region. The first noticeable symp-toms include difficulty understanding higher pitched voices, such as the voices of females and children, and difficulty understanding certain consonant sounds, which are primarily high frequency in nature. The extent of NIHL varies depending on the level and duration of noise exposure and on an individual?s susceptibility; despite having similar noise exposure, individuals can experience differing degrees of hearing loss, or none at all. NIHL is almost always preventable. To reduce or eliminate the possibility of NIHL, an individual?s noise environment must be analyzed and appropriate action taken to reduce noise exposure.

Dec 1, 2009

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

By Robert J. Hundhausen, GEORGE M. GRISMER

This circular describes the methods and costs of deepening the Silver Summit three-compartment shaft in the Coeur d'Alene mining region of Idaho. A noteworthy rate of advance was achieved at this operation by the successful use of a mechanical shaft-mucking machine. The Silver Summit mine is 1 mile west from the town of Osburn, Idaho, via U. S. Highway 10. The adit-level portal of the mine is on the south slope of the Coeur d'Alene River Valley at an altitude of 2,700 feet. The Silver Summit shaft is 6,000 feet from the portal. In past years this shaft had been sunk from the adit level to a depth of 1,500 feet. During 1946 the Polaris Mining Co, deepened it to 3,095 feet. The work was done under a co- operative development agreement between the Silver Summit Mining Co. and the Polaris Mining Co.

Jan 1, 1948

By C. J. Walker, Ray V. Huff

The feasibility of inert - gas cushions in underground gas storages was studied by the Bureau of Mines in accordance with a continuing program of cooperative research between the natural gas industry -- through the American Gas Association . As mixing of the inert - gas cushion with the stored natural gas is undesirable , the various mechanisms tending to bring about such mixing were the subjects of both theoretical and experimental studies . These studies indicated the practicability of such cushions is dependent upon both reservoir and operating conditions . Equations and tables of illustrative data relating the various reservoir and operating conditions to the expected time required for undesired mixing to occur in ideal reservoirs are presented . This information permits estimating the relationship of such factors in actual storage operations .

Jan 1, 1964

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969