Search Documents

By Johan Finsteen Gjødvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad. This has been done by use of an online survey through the most of 2018. Questions have been raised on vibration monitoring during blasting. The existence of norms, guidelines or standards and how they are used. Even though the questions have been kept at a high level they are formed to try to map the different national standards use of such things as frequency, guidance on monitoring position, distinction between different types of structures, requirement to the equipment and more. Furthermore a few initial questions have been raised on other environmental monitoring relevant for blasting. The respondents are national, cooperate or individual members of EFEE. The answers are experts in the use of explosives and vibration-monitoring in their respective countries. More than 60 have answered the questionnaire from 29 different countries. Mainly European as well as other nations including India, Israel, Nigeria, Saudi Arabia, UAE, USA, Greenland and Hong Kong. By analysing the incoming answers, the differences and similarities in vibration monitoring of the respondents has been clarified and mapped. Where possible other environmental monitoring has also been analysed. Where needed the different guidelines, standards and regulations have been visited to verify the answers and further elaborate on the comparison.

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By Kia Riihioja, Mike Higgins

A major difference between electronic and pyrotechnic detonators is that, in almost all but the simplest of blast layouts, computer software is required to plan a blast using electronic detonators. While it may be possible to program delay times without software, using only the manufacturer’s control hardware, the full potential of electronic detonators can only be realized through software. Until recently, the only software available has been provided by the suppliers of the electronic detonators. These usually have just enough features to create a hole layout and to assign times to the detonators in the holes. The software is also able to communicate only with the manufacturer’s detonators. This means that the client may be compelled to change several parts of the blasting process when a different delay system is adopted, from design through to implementation and reporting, even though these may be sub-optimal at the client’s mine. While many authors have demonstrated improvements in blasting outcomes using electronic detonators, very few have discussed how the delay times were calculated. Where the calculations are discussed, it is also obvious that the delay times must be monitored and re-evaluated as conditions in the mine change. For example, the principles of superposition and scaled distance, burden relief and energy cooperation between holes should be checked constantly for different locations within the mine, changes in rock properties, or even for differences between design and actual hole positions. The most common methods in blast design software to calculate delay times are inter-hole interval, relief contour and direct editing. Although they are simple in concept, they can result in fundamental errors if they are not applied correctly. The software for electronic blast designs should be capable of not just a timing calculation, but also of showing, to some degree, the impact and interaction of the calculated times.

Jan 1, 2004

By Ambrose Buchanan, Rob Farnfield, Charles Adcock

Beginning on 7th September 1940 the City of London was subjected to 57 consecutive days of bombing in what became known as the ‘London Blitz’. To commemorate the 70th anniversary of this event a television series was commissioned that required the open detonation of World War 2 equivalent bombs close to purpose built structures constructed using period design and materials. The structures were built on a remote test facility in the North of England that is able to fire large quantities of explosive in the air.

Jan 1, 2011

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025

By S. Geerts, J Davidson

The purpose of the experiment was to determine detonation characteristics of various improvised explosives. The test consisted of detonating a pipe filled with an explosive compound inside of a plywood arena. The pipe will be located in the center of the arena to ensure even distribution on the witness panels. Details on pipe dimensions, weights of the pipe and explosive, and the density were recorded prior to testing for use in the model calculations. The same size pipes were used throughout to minimize the variables inherent in testing. The plywood witness panels will capture the fragments so that penetration data was obtained, primarily the surface area of impact and depth of penetration. Through the use of the penetration data in conjunction with a mathematical model the original fragment velocity was determined. The mathematical model was developed to measure lethality of fragments from explosives and was modified to determine the original fragment velocity instead. From this model other variables such as the Gurney velocity were calculated. This test was done with an explosive compound that was commonly found, and numerous improvised compounds. In order to guarantee accurate data all of the explosives used for testing were cap sensitive, to eliminate the need for a booster charge which would introduce many unknown variables. The one common explosive compound that was used was C-4 which has known data in order to show accuracy of the model and calculations. The other 5 compounds chosen will not have this data as they will primarily be improvised mixtures.

Jan 1, 2011

By John Atkinson, Steve Repola

This paper will describe two blasting plans that have been developed for American Aggregates' Marble Cliff Quarry located near Columbus, Ohio. Two different limestone formations are mined on different levels of the quarry. Each formation requires a different blasting plan which address vibration considerations, crusher productivity, drilling and blasting costs and adjacent neighborhood concerns. Controlled blasting is critical to continued mining operations in this Midwest urban setting.

Jan 1, 1993

By Alan Hooper, James E. Mischler

Construction began in 1984 for a 5 megawatt hydroelectric power retrofit at the O'Shaughnessy Dam for the City of Columbus, Ohio. The construction necessitated excavation of limestone bedrock up to 27 feet below the normal water level of the river downstream of the dam. Proximity to the river and difficult terrain resulted in an interesting and challenging construction project.

Jan 1, 1986

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By G. Adderley, Rob. Farnfield, L. Bermingham

The benefits of using electronic detonators within the drilling and blasting process in both surface and underground mining operations are well established and the use of this technology is widespread in the minerals industry. However, many users of such devices will also have experienced misfires where an electronic detonator has malfunctioned and shows evidence of damage from either transient shock or gas pressure. This is typically exhibited as a detonator shell that has collapsed causing damage to the internal electronic components before the detonator has initiated. Users often describe such detonators as being “shrink-wrapped”. The excavation of a misfire is always a hazardous operation, and it is better to minimize the risk of one happening in the first place. As part of a programme to improve understanding of this phenomenon and to allow a comparison between differing designs of detonators, a simple practical test was developed. This process involves the firing of a booster near electronic detonators in water. This paper describes this test work and draws some tentative conclusions on pressures for onset of damage with detonator shells made from different materials. The investigation has also yielded data showing that for some designs there is little difference between the pressure resulting in complete malfunction and sympathetic detonation

Jan 1, 2024

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By Brandon Fryman, Josh Hoffman, Rhys Baker

A post-detonation debris collection project was led in conjunction with a large ammonium nitrate (AN) railcar detonation conducted by the Department of Homeland Security-Transportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in a Quantitative Risk Assessment (QRA) tool.

Feb 1, 2020

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

By Angelina Anani, Seffit Aderuyi, Sylvester Avane, Joseph Wilson-Sey, Amatus Niminye

The Edikan mine in Ayamfuri, Ghana, faces economic challenges and community resistance due to its proximity to residential areas, particularly concerning blasting operations. Controlled blasting trials using air deck applications were conducted to address community concerns by minimizing environmental impacts and explosive costs. This method involves utilizing an air gap within blast holes to prolong the action of shock waves on the rock mass, enhancing crack formation and reducing rock movement. The trial project at the Edikan open pit gold mine aimed to evaluate the effectiveness of air deck blasting in reducing ground vibrations and overpressures, and to assess its impact on blast performance and economics in the prevailing geological conditions of meta-sediment and hard granite rocks. Results indicated lower Peak Particle Velocity (PPV) and Peak Sound Pressure Levels (PSPL) values in the air-decked blasts. Additionally, more uniform rock fragmentation and enhanced blast economics were achieved. Explosive costs were reduced by 20–24%, saving $0.97 to $2.24 per hole depending on the rock type. Overall blasting costs per volume decreased to $0.54 in granite and $0.48 in meta-sediment compared to conventional methods.

Jan 21, 2025

By Edward P. O'Hern

The importance of the so-called explosives and the increasing extent of their use are evident from the fact that the production in the United States for the year 1910, as shown by the United States Census reports, amounted to the enormous total of approximately 480,000,000 pounds, this being more than double the production of 1905 and more than three and one-half times that of 1900

Jan 1, 2015

By Dr. Calvin J. Konya, Anthony Konya

Beginning on the Niagara Power Project, presplitting became a widely used blasting technique to obtain smooth walls in mining and construction projects reducing scaling, creating more stable pits, allowing the application of slope steepening to reduce waste removal and increase mining depths, and increasing the safety of mine and construction workers. This technique has been minimally studied in comparison to production blasting and currently two separate theories are present on the mechanics behind the presplit. The first is that shockwave collisions between boreholes cause a tension zone to develop causing the split formation. The second is that gas pressures build in the boreholes causing hoop stresses between holes leading to a presplit formation. Practical blasting methods in presplitting such as propellant presplitting and precision presplitting would not be applicable based on the shockwave theory yet are widely used and documented in the industry. Along with this, modern research using a borehole simulation device and advanced pressure gauges have allowed the authors to obtain true borehole pressures in decoupled blastholes. This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

By Anthony Konya, Calvin J. Konya

This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

Feb 1, 2020

By John Horgan, Ethan Marcoux

Explosives have been used to demolish many unsafe structures around the world. However, it is unlikely any demolition job has ever involved destroying buildings already buried 40 feet (12 meters) into the world’s largest ice sheet. That is what happened to the original research station at the geographic South Pole, built back in the 1950s, following a series of discrete explosions between 2011 and 2013.

Jan 1, 2015

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine.

Feb 1, 2020