Search Documents

The present stage of economic development of the Broken Hill lode, attained after 40 years of active exploitation, leaves little opportunity for the study of the zone of secondary sulphides.Little remains of the oxidised zone, and the observations of the secondary sulphides of copper and silver can rarely be made on specimens collected in situ. A few specimens containing secondary...

Jan 1, 1927

By Yinxiang W, Chunlai Y

In older to improve efficiency of surface pre--grouting in sealing off water in heavily water-bearing strata, such as sandstone,siltstone and limestone, several methods have been used in China, they are ; intermittent pre-grouting, adjusting pre-grouting parameters and stepwise repeated pre-grouting methods. The paper describes effect of deviation on water sealing in pre-grouting. Deviation correction measures, like mechanical, technological and changing hole position methods have been introduced with satisfactory results in practical engineering projects without increasing the volume of engineering project and without causing delay.

Jan 1, 1988

Magnesium-rich olivine is used as an additive in LKABÆs iron ore pellets in order to improve the high-temperature properties of the finished products. Olivine is only added to the pellets that are manufactured for ironmaking in the blast furnace process. The olivine comes from Minelco/LKABÆs mine at Seqi in Greenland. This dunite complex of Archean age contains about 95 - 98 per cent olivine. The grain size is typically 1 - 3 mm but much larger euhedral olivine crystals are common in the porphyritic type. The serpentinisation is absent or weak. The most common minor minerals are chromite, chlorite, talc, phlogopite, amphibole and pyroxene. The crushed olivine is transported to LKABÆs pelletising plants in Northern Sweden. After grinding, small amounts of olivine are mixed with the magnetite concentrate. The concentrate is rolled into green balls, about 10 - 14 mm in diameter. The moist green balls are transferred into the pelletising machine where the maximum temperature is about 1250¦C. The residence time in the pelletising machine is about one hour. Olivine is used in order to get pellets with better high-temperature properties. This paper deals with the olivine alteration during the pelletising process and the behaviour of magnesium following the decomposition of magnetite. The reactions are quite complex in the pellets because the physico-chemical conditions vary considerably in the process from one process step to another, and in the pellet bed from the top to the bottom. Some olivine particles in the finished product show very slight alteration, some particles are completely decomposed. The formation of the iron-rich coronas around the olivine particles is the most typical alteration. In the finished pellets the magnesium is mainly distributed between the following phases: unaltered olivine, coronas, Mg/Fe-ferrite and silicate slag.

Jan 1, 2008

By Nickson NM, Lancucki CJ

X-ray diffraction and differential thermal methodshave been used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis has been made of the mineralogy and. particle size distribution of eighteen samples from beds' in two pits in~the Recent seaiinents in the Adelaide plains, of six white clays.: developed from the weathering of the Adelaide series of `sediments and, of ,four -Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products 'in the Adelaide area are manufactured from mixtures of these clays:, so the mineralogy and particle size distribution have been determined of eighteen clay mixtures used to make red bricks, cream bricks,. facing bricks, pipes and tiles. Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.

Jan 1, 1963

By D Cohen, A Wurster

Many Southern African mining operations produce mine water which is beneficially and productively utilised on the mine sites and to support other water uses. Mine water treatment typically takes place within the context of integrated mine water management involving pollution prevention, waste minimisation, recycling and reuse as well as river discharges. Development of new and improved mine water treatment has focused on the neutralisation of metals removal, desalination of high sulfate waters and passive treatment. Mine water neutralisation processes now incorporate a combination of natural limestone and lime treatment, as well as features to maximise gypsum precipitation. The South African CSIR developed a suite of limestone-based neutralisation processes, which include reuse of CO2 and CaCO3 generated in the process. Desalination of high sulfate mine water is typically done using one of the following technologies:biological sulfate removal with different approaches to the handling of the sulfide generated in the process, and ultrafiltration (UF)/reverse osmosis (RO) treatment with different approaches to the handling and disposal of the brine. The current research and development focus is the separation and recovery of saleable products from the treatment residues and brine streams.

Jan 1, 2006

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978

By S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of quartz-reef fields that make up the greater Central Victorian Goldfield. At Bendigo gold particles are characterised by their very coarse nature, ranging from below 100 to over 10 000 ¦m in size. Some 60 per cent of the gold occurs in particles greater than 1000 ¦m in size. This characteristic ensures that the mineralisation is very challenging to both sample and evaluate. Diamond drilling provides a measure of geological structure, but is a poor measure of in situ grade, understating it by up to 75 per cent. Drilling combined with on-reef development, bulk sampling and geological interpretation has been used to define Indicated Mineral Resources. For grade control, a balance had to be sought between sample representivity, cost, turn around time and practicality. Sampling of extreme nugget effect deposits generally requires the use of bulk sampling in order to be representative. However, the cost and turn around time is significant. As a result, a 50 kg micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can discriminate between ore and waste. As the mine passes into production, grade control will increasingly become dependent upon geological data collection and interpretation.

Jan 1, 2005

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2005

By Tooley S. M

An experimental investigation of the hydraulic cuttability of coal from the Theiss Dampier Mitsui mine near Moura, Central Queen land illustrated the ability of established cutting equations to describe the behaviour of the coal during cutting. The experimental equipment developed for the work proved reliable. The results of the experimental programme are consistent with accumulated experience from overseas.

Jan 1, 1985

The mining. operations of Bougainville Copper Pty Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea. Mineralisation in the Panguna area was first established by C.R.A. Exploration Pty Ltd in 1964. Exploration work since then has established ore reserves estimated to be 760,000,000 tons of.0.47% copper and 0.4 dwt./ton gold. An economic feasibility study completed in July of this year has enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons per day. The concentrate will be pumped as a slurry through a 15 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 megawatt steam power station, and access roads.

Jan 1, 1970

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By Hughes CA

The need to recover metals from low grade deposits, old tailings, etc., combined with improvements in equipment design and the development of new extractants, has resulted in solvent extraction (SX) metal recovery reaching new importance (Webster & Ferron, 1993). The basic principle of solvent extraction is the use of an equilibrium system in which a metal ion is transferred from an aqueous phase into an organic phase, (Equation 1), (Ritcey, 1984). M + E ME . (1) The organic extractant (E) is usually specific for a certain metal ion (M) and forms a metal complex in the organic phase, leaving the impurities behind in the aqueous phase. To recover the metal, the equilibrium is reversed and the metal ion is transferred back from the organic to another aqueous phase in a process called stripping. The metal is then recovered from the aqueous strip solution, usually by electrowinning.

Jan 1, 1990

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

I have been asked to speak today on the topic of Project Finance in the Mining Industry. Through this presentation, I hope to give you a broad outline of the concept of project finance. The first half of the presentation covers the principles involved in project finance and the second half moves to aspects more specific to the mining industry. I have worked for 3 years at Rothschild Australia. Rothschild provide finance for projects in the mining industry, world wide. We finance both large and small projects, with facilities varying from $2m to $100m.

Jan 1, 1990

I stand here as a financial advisor who has been particularly close to the whole concept of reporting, independence and all the issues that are brought together in Release 149. However, I was asked to introduce this session by dealing with matters of Prospectuses, Part B's, 3J3's, 12G's and other requirements to report. Now I find it very interesting that one of the keynote issues is whether or not one should have a panel from which one chooses the so-called expert, and this is to deal with the question of independence.

Jan 1, 1989

Initial coal production at Ulan was solely from underground mines. A significant increase in demand for steaming coal in the late 1970's emphasised the need to further expand production and led to the development of the open cut mine which commenced commercial production in June, 1982.During the initial stages of mine planning, feasibility and cost studies were undertaken to determine the most suitable method for coal haulage from the pit. The comparison between a conventional truck haulage system and an in-pit crushing system using a mobile crusher and moveable belt conveyor haulage confirmed that the mobile crusher and conveyor system was superior in every respect for the Ulan mining operations.Technical features and design parameters for the major items of equipment are outlined as well as operating, manning and performance assessments. Minor equipment problems were encountered during initial operation but these have since beenrectified and the plant is now capable of exceeding the design production. Maintenance and energy costs are considerably lower than originally estimated and production efficiencies are continually improving as operators develop new techniques and procedures in the handling of the equipment.

Jan 1, 1985

By Guerney P. J

A suspension of finely powdered ferrosilicon in water is the dense medium used in the gravity upgrading of iron ore, diamonds and other minerals. Ferrosilicon can he lost in the plant through corrosion. The greatest corrosion losses occur when

Jan 1, 1997

By A Purvee, M F. Lee, L J. Mollison

Oyu Tolgoi is a large Cu-Au porphyry deposit in the south Gobi desert, Mongolia. The first of several deep, large-diameter, concrete-lined shafts, Shaft 1, is nearing completion. It will have a finished depth of 1380 m at a diameter of 6.7 m. These shafts will provide access to and hoisting capacity for block caving of deep underground ore. Geotechnical site investigations, and associated predictions of stability and ground support requirements, are compared against actual construction performance. Routine mapping is essential, along with checks against predictions and informing the contractor of ground conditions and variances.Advance rates are compared against predicted rock mass quality. A reasonable correlation exists between Qwall and advance rate. Overbreak and concrete liner thickness is related to the blockiness quotient, RQD/Jn.A ætool-bagÆ of just a few support elements (chain-link mesh, fibrecrete and 2.4 m long friction anchors and resin grouted re-bar bolts) was able to cope with the ground conditions encountered. QA/QC procedures are essential from the factory, through site storage to installation.

Jan 1, 2008

By Box JC

A comprehensive computer simulation has been developed for heap and dump leaching processes. It deals with complex chemical interactions, involving several minerals and reagents, which vary with time and location in the dump. The simulation is generally applic- able to ores of various metals extracted by different reagents. It requires only mineral- ogical data obtainable from drill cores and chemical data obtainable from the literature; there is no curve-fitting with adjustable parameters. Applications in designing testwork programmes, evaluating operating options, transferring experience to new situations and reducing uncertainty in long-term forecasts are described. Specific examples are included illustrating the potential of the simulation.

Jan 1, 1983

By Diessel C. F K, Ng N

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia. An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared. The difficulties of distinguishing structured and non-structured macerals of the inertinite group is discussed in terms of possible improvements to the present Stopes-Heerlen system by extending the classification to include transitional maceral types.

Jan 1, 1969