Search Documents

By Joseph M. Jacisin

Fatigue tests were conducted on 2017-T4 alumium in alloy in an u1lrcthig.h vacuum of 2 x 10-lo Torr and in air. The vatio of vacuum-to-air faligue life for this ~malerial varied Jrom 3.5:1 at a strain of 2.5 X 1O-3 ill. pegr in. to 8:l at a strum of 3.3 x X ill. per 171. Sotlze pvelivtlinary data were also obtained on the faligue life of the alumirnum alloy in a dvy-nitrogen atmosphere. A dark deposit observed on the fracture surfaces of the aiv-tested specimens was identified as oxides of tr~angarzese and magnesium This observalion, and the close correlalion betaveen results obtained in vaCuum and dry-nitrogen environtments, tend to confirm that air stvongly influences the fatigue mechanism by a covrosion process. THE fatigue life of certain metals is known to increase when the atmospheric pressure is reduced. Gough and Sopwith1-2 postulated that this is due to a joint chemical and mechanical process operating in air at the surface of the metal with oxygen and water vapor playing significant roles. Wadsworth and Hutchings3 observed that aluminum is mainly affected by the presence of water vapor. Very little information is available on the fatigue properties of structural aluminum alloys in a vacuum environment. This report describes work performed on 2017-T4 aluminum alloy in an ultrahigh vacuum (2 x 10-loTorr) and in air. Some preliminary data are also presented on the fatigue life of the alloy in a dry-nitrogen environment. 1) EXPERIMENT 1.1) Test Material. The material tested was commerciaT 2017-T4 aluminum alloy which, in addition to aluminum, has an approximate composition of 4 pct Cu, 1 pct Fe, 0.8 pct Si, 0.5 pct Mg, 0.5 pct Mn, plus smaller amounts of other elements.* Some typical naturally age to a substantially stable condition. Specimens were then machined from these rods and ground to a No. 8 microfinish. In order to minimize variation in material characteristics, specimens were made from rods procured from the same lot. 1.2) Apparatus. The apparatus and test specimen used in the fatigue tests are shown in Fig. 1. The device utilized a single-cantilever beam with rotating-bending loading. Bending stress was applied to the fatigue test specimen by placing a spacer beneath the bearing support, thereby providing a constant deflec-

Jan 1, 1968

By Nicholas J. Grant, Oliver Preston

A series of dilute solid solutions of a1uminum and silicon in copper, in powder -form, were internally oxidized, compacted, and extruded, to produce Cu-A12O3 and Cu-SiO2 alloys with 0.1 to 12 vol pct of oxide. Room-temperature tensile tests, creep-rupture tests from 450oto 850°C. conductivity measurements, and recrys-tallzzation studies were made. Oxide particle size and interparticle spacings were determined in an effort to relate the structure to measured strength values by means of known dispersion strengthening theories. A new dispersion strengthening theory, based on the effect of the dispersed phase on the retention of strain energy from the deformation step, zs proposed for this type of alloy, THE study of dispersion strengthening is of partitular interest in high-temperature materials technology in view of the excellent creep-rupture Properties and thermal stability achieved with SAP.1-5 Considerable effort has been devoted to this study in recent years, and encouraging results have been obtained in a number of systems.6 In general, the most

Jan 1, 1962

By Gerard Matthes

Only in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be contemplating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one—inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground—geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the geologist or mining engineer an aerial photograph or mosaic is only a tool, the efficient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic, or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted. Between these two extremes will be found endless variations and possibilities. Hence no set rules can be promulgated. The safest procedure is to treat each case as a separate problem and to carefully weigh the relative advantages and shortcomings of aerial photography before embarking on its use.

Jan 1, 1928

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following standing committees: Membership, Admissions, Papers and Publications, Mining and ' Metallurgy (Magazine), and Library. To these reports you are referred for additional details. Membership Membership, counting all categories other than Student Associateship, continues the upward trend of the last 10 years, reaching a total, as shown in Table 1, of 12,081. The net gain of 406 would

Jan 1, 1944

By E. G. Leonardon

THE first to appreciate and foresee the value of applying electrical measurements to structural studies was Prof. Conrad Schlumberger, Professor of Physics at the School of Mines in Paris. One of his earliest practical undertakings in this line was carried out, in the field, at Fierville-la-Campagne, Normandy, in 1912. His book, published in 1920,1 still stands as an authoritative, fundamental treatise on the use of the electric current in geological studies, in spite of the rapid evolution of geophysics during the last seven years. A remarkable feature of this book is that, even then, it stressed the role of electricity in structural investigations and made public the first successful results obtained therewith. Stratigraphic studies have been pursued continuously by Conrad Schlumberger and his associates since 1912, the only interruption being the World War. The results attained demonstrate the wide possibilities of electrical exploration in structural work. This field of activity is, at the least, as varied and valuable as the search for ore. It is curious that until very recently it has so slightly attracted the attention of geophysicists and geologists on this continent. The purpose of this paper is to present briefly some examples of the practical application of the potential methods to geological studies. These examples are chosen from a number of problems solved in the field by our firm, in the course of its consulting practice. Certain fundamental points are briefly stated before the field operations and interpretations are described.

Jan 1, 1928

By J. F. Abel

It can be concluded that rock mechanics instrumentation, geologic mapping, and operations research in combination will produce an accurate estimate of tunnel support requirements for establishing a steel-set load prediction model. This estimate can be used to increase safety and to reduce tunneling costs. Unnecessary supports can be eliminated; overloaded or insufficient supports can be replaced on a more scientific basis than previously possible. Only a limited number of measurements are required to develop a steel set load prediction model. The results of this study can be applied generally; but, every tunnel must be considered as a separate problem. The construction and geologic variables which were found to be significant in the prediction of rock loads in this tunnel were: steel section modulus, set blocking points, percentage of alteration, relative degree of faulting, relative water condition, distance to the nearest fault, and average joint spacing. INTRODUCTION A combined engineering geology and rock mechanics program was performed throughout the Straight Creek tunnel pilot bore in Colorado in order to develop a technique for estimation of steel tunnel support loads. The technique involves the construction of a statistical model from measured steel set loads, geologic and construction factors. The aim of the investigation was to produce a set of charts, based on these factors, which could be used by a trained man equipped with a hand lens and measuring tape, to specify a safe and economical steel size and set spacing. In order to be of practical value the measured parameters had to be rapidly measurable and capable of quantification. It was apparent from the beginning that quantitative values for many of the geologic factors would have to be arbitrary. It was impossible to ascertain in advance which of the readily determi-nable geologic and construction factors significantly affect steel set loading. As the investigation progressed the number of observations was systematically reduced in order to determine the minimum amount of data which would be necessary for a significant mathematical model. This paper presents an analysis of all the variables measured at each instrumented steel set. The statistical significance of the measured variables was determined. On the basis of this determination, a mathematical model was constructed and charts were prepared to select and space the steel tunnel supports at any given point in the tunnel. Once the effect of geologic and construction factors on set loading is sufficiently established, it is possible to exert close control over the selection of steel tunnel support size and spacing. The magnitude of this rock mechanics program can be appreciated when it is known that there were 44 instrumentation stations for which steel set loads were measured. For each of these sets there were three construction variables recorded, and nine geologic parameters determined (Table I). A rough approximation of the cost for both the collection and reduction of the data would be $50,000. This is in addition to the cost of geologic mapping.

Jan 1, 1967

ONE of the interesting-though not unnatural-features of the whole Porphyry Copper development is the way in which the history of each property dovetails with that of one or more of the others. The same names keep cropping up as one digs into the accounts of events from 1900 to 1915. J. Parke Channing made examinations of Nevada, Ray, and Inspiration, as well as of Miami. Henry Krumb did important work in the early stages of the exploitation of Utah, Nevada, Ray, Braden, and Inspiration. Pope Yeatman was favorably impressed with the Braden property before he had ever visited it, when he saw a batch of Braden ore sent to the United States for testing. It reminded him immediately of Nevada Consolidated ore: indeed, he was unwilling at first to believe that it came from South America. And it was while working on the examination at Utah Copper that Philip Wiseman became enthused with the possibilities of the Ray mines. In 1905, Mr. Krumb, under the general direction of A. Chester Beatty, was strenuously engaged at Bingham, Utah, in arriving at an answer to this question: Should or should not the Guggenheim interests back Jackling to the tune of several million dollars to build the big concentrators at Gafield? Seeley W. Mudd was the Guggenheim engineer on the Pacific coast and in that capacity was indirectly responsible for the work at Bingham. At his suggestion Wiseman came up from Los Angeles as one of Krumb's assistants-at $5 per day, incidentally. A little later Mr. Mudd, in Utah on one of his visits, went down to Bingham. That evening in the old Hills Hotel in Markham Gulch he was going over reports with Mr. Krumb. Wiseman and some of the other engineers on Krumb's staff were present. During a breathing spell, Mudd expressed

Jan 1, 1933

By W. C. Phalen

Introduction............................... 100 Production and Exportation of Phosphate Rock.............. 101 Methods of Conservation........................ 101 Introductory Note........................ 101 Mechanical Methods of Conservation............... 103 Grades of Brown Phosphate Rock............... 106 Preparation of Phosphate Rock for Market, with Phases of Conservation Involved..................... 106 Removal of Overburden.................... 106 Methods of Mining...................... 107 Reworking Deposits..................• 107 Working "Cutters"................... 109 Washing and Drying..................... 111 Conservation of Fines .................... 113 Chemical Methods of Conserving Phosphate Rook.......... 113 Application in the West.................... 113 Chemistry of Process.................... 114 Substitutes for Phosphate Rock..................... 115 Natural Substitutes........................ 115 Phosphatic Limestone..................... 115 Apatite, Nelsonite and Other Minerals Containing Phosphate ... 116 . Apatite in Virginia................... 117 Guano........................... 118 Greensand (Marls)...................... 118 New Jersey....................... 118 Kentucky........................ 119 . Tennessee........................ 120 Alabama........................ 120 Excrement.......................... 120 Bones............................ 121 Artificial Substitutes....................... 121 Basic Slag......................... 121 Phosphate Rock Reserves....................... 122 Florida............... 122 .

Jan 1, 1918

By Robert Schorr

A Discussion of the Paper by Robert Schorr, read at the Atlantic City meeting, February, 1904. (Washington Meeting, May, 1905.) E. T. DUMBLE, Houston, Texas (communication to the Secretary*) :-In addition to the list of publications mentioned by Mr. Schorr and those by Prof. Hofman, I call attention to the following references : Studi sulle Lignite, by Capacci. Turin (1890). (An excellent work.) Report of Brown Coal Industry in Germany. J. Cosmo Newberry. Department of Mines, Victoria (1892). Second Report of the Royal Commission. on Coal Supply. Vol. II. London (1904). Peat Fuel: Its Manufacture and Use. Report of the Bureau of Mines of Ontario, 1903. Mr. Schorr says : " Brown coal and peat are briquetted as a rule without binder," but this statement is entirely true only so far as raw peat is concerned, and it is but partly true of brown coal. With regard to raw peat, briquetting without bond is carried on successfully both in Europe and America, and the development of the industry in Canada is fully described in the Bureau of Mines report for 1903, mentioned above. While there is still room for improvement in the efficiency of some of the arrangements for drying the peat previous to briquetting, a very satisfactory fuel is made at a price which enables it to compete with coal. During the late strike in the anthracite regions of Pennsylvania, the manufacture of peat: briquettes received a considerable impetus, and possibly the attention directed to it on this account may result in a. considerable increase in the output. In Canada. the peat when it is first excavated from the ground

Mar 1, 1905

By Walter C. Lawson

The primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in the Morenci open pit. General Mining Operations Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste is loaded into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high. They are blasted with churn drill holes and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). Preparation OF Panel Grade In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many tics broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed, to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1949

By A. N. Winchell

In connection with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Ringham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance. • Sandstone-limestone Gradation The sedimentary rocks of the Bingham district are chiefly sandstones, with some beds of limestone, all now lying with their strike nearly east and their dip nearly north at an angle of about 30°, near the surface. The limestone beds are remarkably irregular in thickness in some places, but usually change very slowly in composition along the strike. However, the most interesting results are obtained from a study of a section across the beds at right angles to the strike. In some places, such sections show the usual alternation of pure sandstone with nearly pure limestone, in the simple manner assumed in most geological discussions.

Jan 1, 1924

By D. A. Munro, G. P. Contractor

Fourteen 50-lb laboratory melts were investigated to determine the effect of uranium on the tenpering characteristics of loo-carbon (0.06 to 0.1 pct C) steels. It was found that uranium additions, particularly in the range 0.30 to 0.45 pct, enhanced the hardness and both ultimate and yield strength of the experivzental steels in the quenched and tempered condition. The structural and morphological chazges indicated that uranium retarded tempering of the tnartensite, thereby hindering the normal formation of polygonal ferrite formed in the late stages of tempering. The effect of this was to make possible the re-tension of the acicilar ferritic structure in the uranium-bearing' steels. The iraniuin-bearing steels also showed IVidnzanstatten-type growth of ferrite plates and had large prior austenite grains containing assenzblies of fine ferrite grains, mainly acicular in geometry. The fine-grained ferrite structure and the presence of more numerous and apparently smaller precipitates in the uranium-bearing steels are thought to he principally responsible for the itnproved tensile strength and hardness of the experinzental uranium-bearing steels. At ternperirzg temperatures above 455% (850'F) the ferrite in the higher-uraniun steels nzaintained acicularity and, hence, its strength and resistance to tempering. Uranium did not produce a secondary hardening peak. However, it retarded softening during the third stage of tempering because of its effect of inhibiting the grouth of cementite particles and of retaining the acicularity of ferrite plates. The resistance to coalescence accounted for the slow grocth of the ferrite grains in the uranium-modified steels and, hence, fov the persistence of the acicular ferrite structure. IT had been found previously1 that uranium additions up to about 0.45 pct had no significant effect on the tensile properties of low-carbon steel (0.06 to 0.10 pct C) in the as-rolled and normalized conditions, Fig. 1. On the other hand, it was observed that uranium in excess of about 0.30 pct had an embrittling effect as revealed by Charpy V-notch impact results. It was also noted that, as the uranium content increased, the morphology of pearlite changed from lamellar to feathery and the ferrite grains showed an etching effect resembling striated or dashed markings, suggestive of precipitation. The sharp drop in the impact properties shown in Fig. 2 warranted an assumption that the uranium content of about 0.30 to 0.45 pct may produce some secondary hardening reaction on tempering, analogous to that associated with a Cr-Mo-V steel, which shows very poor CVN toughness at the secondary hardness peak in the tempering curve.1' With this background and the reported findings of Hasegawa and noda that low-carbon uranium-treated steel showed signs of secondary hardening, the present investigation was undertaken to determine the effect of uranium additions on the mechanical properties of 0.10 pct C steels. No attempts were made to investigate in detail the mechanisms of hardening, although some suggestions based on the experiments are made. MATERIALS AND PROCEDURES A series of 50-lb induction-furnace melts was made using AISI 1008 rimming steel billets as the melting stock. The melting, forging, and rolling techniques proven satisfactory in previous projects'-3 were employed as a guide for this investigation. The steel was deoxidized with aluminum (2 lb per ton) prior to the addition of high-purity uranium. The analysis of each melt is given in Table I. Properties were evaluated as a function of heat treatment and are presented in terms of hardness and tensile strength vs tempering temperatures. The variation of hardness with the tempering temperature was studied on the quenched and tempered specimens, some of which measured 0.50 by 0.25 in. diam and the others 0.40-in. cubes. Before quenching, the specimens were vacuum-sealed in glass tubes and normalized at 900°C (1650°F) for 20 min. Following this treatment, the sealed specimens were hardened by austenitizing at 955°C (1750°F) for 20 min and water quenching, and then tempered for 1 hr in the range 150 to 730°C

Jan 1, 1967

By J. H. Wernick

IN temperature-gradient zone-melting1 a molten zone is moved through a solid or across a solid surface by the establishment of a temperature gradient. This technique has both practical and fundamental aspects. One practical application is to make p-n junctions for semiconductive devices, particularly for devices in which the junctions are desired within the semiconductor. From a fundamental point of view, the technique is being investigated as a method for determining diffusivities in liquid alloys, and preliminary diffusivity results have been reported by the writer." In this paper, the effects of crystal orientation, temperature, and molten zone thickness in temperature-gradient zone-melting, and the bearing of these effects on diffusivity measurements and n-p-n junction formation are discussed. Experimental Procedure An effect of crystal orientation was noted in early experiments. To facilitate its study, movements of wire zones across a surface, rather than through the body of a single crystal, were observed for various surface planes and travel directions. The experirr-entai setup is illustrated in Fig. 1. The graphite end-section for the high temperature heater has an apron about 1/16 in. above the upper surface of the crystal. This apron insures that the surface temperature of the block is equal to or greater than the temperature within the block at every point, Thus, the zone does not penetrate the block and convection in the liquid is minimized. The experi-through a block is shown in Fig. 2,

Jan 1, 1958

By W. A. Straw

IN the manufacture of telephone apparatus a number of nonferrous sheet metals are blanked and formed to produce a wide variety of parts, which are generally small in size because of space and weight requirements. Many are given sharp bends in forming, so that they may be assembled into compact units. This study covered sheet metal of the alloys of brass, phosphor bronze and nickel silver that are most extensively used by our company. In general, the sheets range from 0.005 to 0.100 in. in thickness and from 1/4 hard to extra spring temper in hardness. As many parts function as flat springs, and others require the maximum stiffness for structural reasons, a large percentage of the metal is used in the hard and spring tempers. So, because of the necessity for the minimum radius of bend consistent with the maximum in hardness, there has been a need for information as to the forming characteristics of these sheet metals in the various alloys, tempers and thicknesses. The literature yields relatively little regarding such forming characteristics, so that designers of apparatus and tools have been largely dependent upon past experience or tool tryouts for guidance. In presenting tabular data intended as a basis for selecting the temper of the metal and radius of the bend, we recognize the influence of many other factors which are not covered in this study. For example, the angle of the bend and conditions of the metal, such as grain size and presence of impurities, as well as conditions of the fabricating process, such as rate of forming and adjustment of the tools, may all affect the result. In addition, a bumping operation subsequent to forming, which is frequently used to set the bend, increases the strain on the metal. We wish to emphasize the fact that this is not considered a scientific investigation of the formability of materials or an attempt to correlate forming, characteristics with various other properties of the metals, except in so far as such properties are controlled by commercial limits on composition and temper.

Jan 1, 1931

By C. O. Fairchild

THE meaning of temperature control can be extended to cover not only the control of temperatures' but also the control of processes through a knowledge of the temperatures involved. In this sense it has a very wide interest. A list of the industries in which temperature control is used in one way or another would cover nearly the entire industrial field. This discussion will be confined to the field of high temperatures. In practically all industries involving operations at high temperatures, pyrometers are used or men are paid for their ability either to estimate temperatures or gage an operation by some physical or chemical change or condition dependent on temperatures. As progress is made in the development of instruments and of methods for measuring temperature, some of these highly skilled artisans are learning the use of a new tool. Many processes have been, in recent years, improved by means of exact measurement thus substituted for estimation, but in a great many industries the pyrometer has had practically no opportunity to demonstrate its usefulness. The perfecting of instruments must be accompanied with a dissemination of the knowledge that new instruments are available and can be economically used. The demand at present, however, is ahead of the supply, and many industries are handicapped by the want of pyrometers. One of the highest paid skilled tradesmen of the present time is the man in the steel rolling mill who knows when proper working temperatures are attained. The metallurgist in his development of steels is continually demanding closer adherence to given temperature ranges in the processes, and the pyrometer is rapidly becoming indispensable. Properties of the finished products are being correlated with working temperatures and so closely that in some cases even the pyrometer is taxed to give the required accuracy. The greatest progress has been made in those industries in which the lower temperatures are used, particularly below 500° C. In this lower range automatic control has been highly developed.

Jan 9, 1919

By M. Nicholas, D. M. Poole

The diameters of sessile drops have been found to increase linearly with time in five reacting binary metal systems. The spreading rates of the drops are markedly dependent on temperature and on prior alloying of the solid with the lower melting point metal, hut are independent of the drop volume, wetting atruosphere , solid-surface roughness, and prior alloying of the drop with the substrate metal. A mechanism has been suggested that relates the linear-spreading rate to lateral diffusion of the liquid-metal atoms into the solid at the drop edge. An Arrhenius- type equation has been derived that describes the temperature dependence 0) the spreading rate, and although the agreement between the actual and the predicted pre-exponen-tial terms is poor that between the activation energies is excellent and the variation in the spreading rate of copper on Ni-Cu alloys produced by different extents of alloying can be predicted with considerable accuracy. CHEMICAL interactions frequently change the wetting behavior of solid-liquid systems causing, for example, "secondary spreading1 of sessile drops beyond the size defined by the surface and interfacial tensions of the unreacted components. The kinetics of the contact-angle decreases associated with this spreading are similar for many systems, but few studies have been made with the objective of determining whether the similarities are a reflection of a common mechanism. Some workers2,3 have assumed the secondary spreading is controlled by changes in the liquid surface and liquid-solid interfacial tensions and hence by the composition of the liquid, and contact-angle changes measured by the vertical-plate technique have been used to follow the course of liquid-solid chemical reactions.4 Other processes that have been invoked to explain these time-dependent changes in specific systems include the removal of adsorbed gas from the liquid-solid interface.5 penetration of containment layers on the solid Surface,6 interdiffusion,1,7 reori-entation of the solid surface into a wettable configuration: vapor-phase transport of the liquid onto the solid in advance of the drop,9 and, from vertical-plate studies. capillary flow between oxide layers and the solid surface.10 One of the reasons for the profuseness of these suggestions may be the complexity of the contact-angle change kinetics. However, in an analysis of secondary spreading gold and copper on UC,11 it was found that the diameter of the contact area between the sessile drop and the solid surface showed a simple linear increase with time although contact-angle changes were more complex. To check whether the linearity was merely fortuitous! additional exploratory work was conducted with four reacting metal-metal systems: Au on Ni. Cu on Ni, Cu on Fe, and Ag on Au. Linear spreading was observed in every case even though the kinetics of the contact-angle changes were complex. A further detailed study of the kinetics of linear spreading of five reacting metal-metal systems has been made with the object of determining the mechanism involved. The influence of variables such as temperature, drop volume. and the initial composition of the drop on the linear-spreading rate has been measured and compared with those predicted by a number of possible mechanisms. The systems employed in this study (Cu and Au on Ni and Pt, and Ag on Au) were selected because of the availability of potentially relevant chemical and physical property data. the simplicity of their phase diagrams at the wetting temperatures, and the ease of experimentation. EXPERIMENTAL TECHNIQUES The purities of the metals used in the study were: copper, 99.9 pct; gold. 99.96 pct; nickel, 99.2 pct; platinum 99.99 pct; and silver, 99.999 pct. The wetting tests were performed in a split tantalum tube vacuum resistance furnace of a conventional design. The furnace element was held vertically and was 1 $ in. in diam and 6 in, long. Viewing ports were provided in the water-cooled chamber to enable the specimens to be observed in both the horizontal and vertical planes. The temperature in the hot zone of the furnace could be held at 1500" i 5°C for an indefinite time. The surfaces of the solid-plaque metals were ground flat on Microcut paper and both the sessile drop and substrate metals were ultrasonically cleaned in methyl alcohol prior to their insertion in the furnace. After loading, the furnace was pumped down to a pressure of 2 x 10-5 mm of mercury and degassed for 30 min at 900° to 950°C. The temperature was then increased at more than 100°C per min to that used in the wetting test. The vacuum at the wetting temperature was better than 5 x 10-5 mm of mercury. Dewetting and retraction of the drop on cooling did not occur and the contact-area diameters, therefore, were measured after solidification with a vernier traveling microscope. The diameters quoted later are arithmetic means of ten measurements. The standard error of the mean never exceeded 3 pct and was often less than 1 pct.

Jan 1, 1967

By Arthur A. Center

AT the beginning of 1944 it was expected that the production of metallic zinc in the United States from domestic and foreign concentrates would exceed the 1943 figure though domestic production of concentrates was expected to drop below the 1943 rate, mostly in the Tri-State area. Imports of concentrates were estimated to more than take care of such deficiency. North American concentrate production, available for import to the United States or elsewhere during the year, was estimated at over 200,000 tons recoverable zinc content; South American at about 65,000 tons; Australian at about 50,000 tons. Production of both concentrates and metal in the United States, however, did drop, attributable in considerable part to man-power shortage in the industry. However production exceeded consumption, which fell off, and stocks of metal increased. These stocks have increased since the middle of 1942 but production and consumption are coming nearer to a balance. The A, B, and C premiums, which have played an important part in keeping up domestic production of concentrates, extend only to the middle of 1945 by present legislation. Congress is being asked for their continuance during the war and

Jan 1, 1945

In a straight caving system, the ore is first undercut and then broken down by its own weight or .by the weight of the overlying rock, or by a combination of both. Operations that involve the caving of the material overlying an orebody as an essential part of the work are also classed as caving, though practically all the ore is broken by drilling and blasting. Actually there are two distinct methods—sublevel caving and block caving, and modifications thereof. The mines described are Miami and Alaska Juneau.

Jan 1, 1925

By George Frederick Kunz

Mexico has been famous for its silver-mines ever since the Spanish conquest; but in respect to gems, although many varieties occur, yet only a few have been obtained in any important amount. Considering the extent of country in Mexico and ill the adjoining States of the Central American Republics, and the richness of mineral wealth that must surely exist there, our present knowledge of the occurrence of precious stones is remarkably small. The great prevalence of igneous rocks would lead us to anticipate the future discovery of many localities of gems and ornamental stones, when fuller scientific exploration shall have taken place.* At the present time the only gem-stone that is systematically mined in Mexico is opal, and the only important ornamental stone is tecali, the so-called Mexican onyx. In addition to these may be mentioned the pink garnet, or rosolite, found in one

Jan 1, 1902

By Y. A. Chang

Heat content values of tantalum monocarbide and tungsten monocarbide have been determined from 325" to 985°K by means of a drop-type diphenyl ether calorinzeter. Based on the values obtained in the present study and those available in the literature, best values lected and computed from 298. 15°K to temperatures close to their respectiue melting points. At temperatures higher than 1700°Kfor TaC and 27000 K for WC, values of Cp and related thermodynamic quantities were extrapolated based on the two Debye parameters: one corresponds to the metal sublattice and the other to the carbon sublattice. The contrzbutzon In the total specific heat due to lattice dilation was evaluated using the Nernst-Lindemann relalionship. The calculated values of Cp were in good agreement with the In view of their refractoriness, tantalum monocar-bide (TaC) and tungsten monocarbide (WC) are of con- experimentally determined ualues. Furthermore, the calculated values of the absolute entropies at 298.15"K were 5.03 and 4.15 in comparison to the experimental values of 5.05 and 4.15, all expressed in the unit of cal per degg-atom. Using the same Debye parameters, values of the linear coefficients of ther mal expansion for TaC and WC were calculated from absolute zero to their respective melting points using the Grüneisen equation. The calculated values are in excellent agreement with the experimental values available in the literature. Finally, the values of the bulk modulus of TaC from room tenzperature to temperature near its melting Point were also calculated using the equation recently derived by Anderson. No cot~ipari-son between the calculated and experimental values can be made due to lack of experimental data. siderable practical interest. In order to completely define these materials, it is necessary to know their thermal properties as a function of temperature. Tantalum rnonocarbide having a NaCl structure (B-1 type) melts congruently at 4250PK,1 while tungsten monoearbide with a simple hexagonal structure (Bh type) melts per itectically at 3049°K into melt and graphite.2 In the present study, the heat content values (from which

Jan 1, 1968