Search Documents

By Jafar Safarian

A new kinetic modelling technique has been applied to study the rate of MnO reduction from slags by dissolved carbon in liquid iron. Based on a consideration of the fundamental reaction kinetics, a general differential equation for the slag reduction process has been formulated, which then is solved analytically for certain special cases. By re-writing the solutions in a dimensionless form the poorly known kinetic constants are eliminated, which makes the model both flexible and applicable to a wide range of experimental conditions. For example, changes in process parameters such as temperature, metal composition, slag composition, gas composition can readily be captured along with variations in the crucible geometry. Based on a comparison with a series of experimental reduction curves being reported in the literature, it is concluded that the predictive power of the model is surprisingly good, yielding outputs that are both reliable and physically reasonable. An attractive feature of the model is that it provides an alternative way of calculating the activation energies from experimental reductions curves. For example, it suggests that the activation energy for the reduction of MnO by dissolved carbon in liquid iron is about 90 kJ/mol, which is different from the previously reported activation energies. The model also suggests that the crucible geometry, which affects both slag the volume and the resulting slag/metal interfacial area, has a significant influence on the overall reduction kinetics. This design parameter is a key to further optimisation of the process on an industrial scale.

Jan 1, 2006

By Fashina Olugbenga Emmanuel, Ghazali Akeem, Adegbola Adekunle Amos, Omotoyinbo Joseph Ajibade, Olaniran Oladayo

"Modern engineering materials are required to be light weight and corrosion resistant, coupled with high strength and hardness. In this work, Al formed the parent metal and alloyed with 2.03% of Copper by sand casting process. The cast product 2024 was warm worked at various temperatures ranging from 300 to 5600c at 5%, 10%, 15% and 20% deformation respectively and aged accordingly. The results showed that the mechanical properties vis-à-vis hardness, tensile improved with increasing % deformation at a higher temperature. This was due to the progressive close-up of the voids emanated from casting by increasing deformation which is evident from the micrographs. MATLAB was also adopted to generate a model capable of determining the trend of flow of stress at operating temperatures. This was of immense value due to an increasing impact at higher percentage deformation with temperatures. Hence, Al -alloys will find applications in land vehicles, ships, trains, and aircraft, at elevated temperature.INTRODUCTIONThe problem of safe vehicle design with maximum impact energy absorption is a significant subject in structural crash worthiness design [1]. All engineering designs are expected to ensure the safety of users' life. This informed several studies meant to probe the causes of component failures in equipment, vehicles, and aerospace design and decide on appropriate solutions through materials selection techniques. A common example is in the design of crankcases and heads, piston, and cylinder blocks. As with engine blocks, cylinder heads can be made of Cast Iron or Aluminium Alloy. A head made of Aluminium alloy is lighter in weight than if it were made of Cast iron [2]."

Jan 1, 2013

By Murray Hughes, Neil Brown, John Carran

"A control system architecture has been developed using the Ward-Mellor structured analysis techniques for real-time applications. This approach has produced several advantages over traditional control system implementation methods including:•,partitioning of the control system into discrete control functions.•,easy identification of the interaction between individual control functions and the rest of the system including the impact of changes at the control system boundary (i.e. additional inputs or outputs).•,simplified control software testing.•,a closed loop design, implementation and documentation process.This paper describes a generic control application in which the process specification and control system design are logically linked. Both components are used by process engineers for on-going development.IntroductionAluminium is reduced from alumina in multiple electrochemical semi-batch reactors. Raw material additions and molten metal withdrawal are made at discrete intervals ranging from seconds to days. The electrolytic reduction process is continuous, despite the semi-batch nature of the material inputs and outputs. The chemical and physical processes that occur within each reactor are complex and interdependent, therefore simple methods used for the control of many chemical processes are impractical. The process control system is required to optimise operating efficiencies within the safe operating zone.The process control of aluminium reduction cells is heavily biased towards calculation of process variables with relatively few measured sensors. Each cell is controlled independently of the other cells, although changes to process conditions and raw material . quality will affect all cells. The process responds relatively slowly and with significant time lags. Measurements and process variable calculations occur each second, however the accuracy and precision of actuator response and sensor sampling are measured 111 milliseconds. Time-based scheduling is a significant component of reduction cell control."

Jan 1, 1994

By Ahmet Geveci

In this work it is aimed to assess the plant analytical data which appeared during efforts to decrease the effect of carry-over slag (basic oxygen furnace slag) that can not be prevented to leak during tapping of steel in the ladles. While the amount changes, carry-over slag that escaped to ladle, consists of appreciable amount of reducible oxides (?FetO? and MnO) which act as oxygen source for steel bath. By using aluminum dross, containing %30-35 metallic aluminum, which is a non-recoverable process outcome (discard) for most of the aluminum factories, slag reduction behavior will be analyzed together with other parameters such as reaction time, initial amount of total Fe+MnO, amount of reducing agent and reducing effect of soluble aluminum in steel bath while obtaining a slag composition which promotes higher desulphurization capacity and inclusion removal for liquid steel.

Jan 1, 2006

By Ovidiu Pasca

Several improvements in converter equipment and operation at BHP Copper have reduced the converter cycle time as necessitated by an increase in flash furnace output. The resulting higher intensity performance of the Peirce-Smith Converters has had a major impact on the dust handling and off-gas cleaning systems. This paper describes work carried out on the design of a new converter hood with particular reference to the thermal analysis and hood performance aspects. Changes in converter cycle time and campaign life as result of the process and equipment improvements are discussed in a separate paper.

Jan 1, 1999

Convential smelting of copper - cobalt - iron sulphide concentrates result in th eoxidation of cobalt and iron, which are subsequently lost into the slag. The emission of SO2 bearing gas from smelting causes serious health and environmentsl problems. In this investigation, three different types of copper - cobalt - iron sulphide concentrates, derived from froth flotation, were investigated, the concentrates, each containing more than 40 wt % percent gangue material, were directly reduced in the presence of lime and corbonin the temperature rnage of 1073 K - 1573 K, fo rthe production of an alloy containing copper, cobalt and iron. We demonstrate the basic principles of process physical chemistry for the recovery of alloy by carrying out a detailed process analysis utilising the predictions from thermodynamic equilibrium and results from the kinetics of reduction reaction. The effect of temperature on the reduction kinetics and alloy formation were determinedand analyzed in detail.

Jan 1, 2012

By W. G. Davenport

This chapter extends our mathematical description of flash smelting to -nitrogen in the flash furnace blast. As in chapters 4 and 5, the discussion is limited to auto thermal smelting (no hydrocarbon combustion). Hydrocarbon combustion is introduced in Chapter 9. Outokumpu flash furnace blast is a mixture of air and industrial oxygen. Most of its N2 originates in the air portion of the blast. A small portion originates as an impurity in the industrial oxygen. The nitrogen entering a flash furnace must always be heated from its input temperature, 298 K in this chapter, to its off gas temperature, -1500 K. Energy must be supplied for this purpose. With auto thermal smelting, the energy is-provided by oxidizing extra Fe-and S.

Jan 1, 2001

By Art Johnston

Gas handling at Magma Copper Company's, San Manuel smelter receives process gas from a flash smelting furnace and four copper converters. The major gas handling equipment consists of four electrostatic precipitators and a sulfuric acid plant. Process vessels in gas handling are typically confined spaces. Lethal gases., mechanical and chemical hazards, and the difficulty of rescue, should an accident occur, makes this area a must in the safety plan. The presence of hazardous chemicals and explosive gases in process vessels and piping are of major concern when repairs are required. Proper job procedures are critical to prevent injury during repairs. This includes plant employees and contractors who are likely to be unfamiliar with the hazards involved. The safe operation of a gas handling operation must include the functions of operations employees on a daily basis. This includes a safe working environment and involvement. of all employees in the safety program. If an injury does occur quick medical response is critical to prevent serious injury. Medical responders must be adeqliately trained and prepared to treat the injured person without becoming victims themselves.. The methods used at Magma copper Company to deal with these safety problems are the focus of this presentation.

Jan 1, 1992

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

By Tracie Zoeller, G. Paul Neitzel, Jr. Sanders

"As-cast aluminum alloy microstructures are highly segregated. Coring occurs when solute is rejected during solidification resulting in a non-uniform solute distribution across the dendrite arms. Furthermore, coarse constituent phases are formed in the interdendritic channels as a result of coring. These constituents are either soluble or insoluble and can form from the major solute elements, or the impurity elements iron and silicon. The dissolution of these constituents, or precipitates, is an important consideration in determining the microstructural evolution of an alloy. The properties of an alloy are significantly affected by the morphology of the precipitates. Precipitates can be either beneficial or detrimental to the properties of the alloy. Regardless of the nature of the precipitates present, it is useful to understand the dissolution process. A diffusion-limited dissolution model for planar precipitates is presented and compared to an analytical solution and to models in the literature. Experimental data for the dissolution of AhCu precipitates in a dilute alloy are compared to the proposed model, and found to have good agreement.IntroductionDuring the processing of precipitation hardening alloys, beginning with the solidification step and ending with the final solution heat treatment step, there are a variety of particles that form. Some of these particles must be dissolved and solute redistributed and re-precipitated in a more homogeneous distribution than as it first appears in the as-cast microstructure. The particles can be classified by size as microstructure develops during processing. Coarse particles that form during solidification can either be soluble, partially soluble or insoluble. These particles can be the result of coring of the major solute elements as well as the limited solubility of elements such as iron and silicon. Iron and silicon can combine with the major solute elements such as copper in 2xxx alloys forming coarse phases often referred to as constituents. Figure l(a) shows the as cast microstructure with the constituent phases, Al2Cu and the insoluble phases containing Al-Fe-Mn-Cu-Si [7]. During preheating the soluble phases such as AhCu that were formed by eutectic decomposition must be taken back into solution, whereas the insoluble phases remain essentially unchanged by most thermal operations. Figure l(b) and (c) show some of these constituents after subsequent preheating steps. In Figure l(b), AhCu platelets are shown and in Figure l(c) the remnants of the AhCu phase are noticeable, along with Mn-bearing dispersoid phases. Reduction in the volume fraction and size of these phases improves the ductility and fracture toughness as well as reducing the inhomogeneities that occur during coring. Also adjacent to the dendrite arm boundaries are smaller AhCu phases that precipitate by a solid-state transformation on cooling to room temperature."

Jan 1, 2004

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen ternary system, which is of fundamental importance for discussing the' recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, SbO1.5 and Sb2O3) in the PbO-SbO1.5 and PbO-Sb2O3 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By Thomas Frost

In this time of market globalization, many industrial companies are including detailed arbitration clauses in their international contracts, in order to avoid the potential costs, delays, and uncertainties of litigation in foreign courts. Arbitration is less expensive and more flexible, procedurally, than court proceedings, and arbitral awards enjoy much greater international recognition than judgments of national courts. More than 134 countries have signed the 1958 United Nations Convention on the Recognition and Enforcement of Foreign Arbitral Awards, known as the "New York Convention", which facilitates the enforcement of arbitral awards internationally. There are several other similar arbitration conventions that provide for the enforcement of cross-border arbitral awards. Additionally, arbitral awards are not subject to appeal, whereas judgments of national courts are routinely subjected to a lengthy appeals process, and there are very few viable bases to challenge arbitral awards. This discussion will review key considerations in drafting arbitration clauses, including choice of law and choice of forum considerations; issues surrounding the selection of arbitrators; the discovery process; presentation of evidence; and enforcement of arbitral awards.

Jan 1, 2006

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By Ivanildo Hespanhol

"DALYs are a measure of the health of a population or burden of disease due to a specific disease or risk factor. It evaluates the time lost because of disability or death from diseases compared with a long life free of disability in the absence of disease. DALYs are calculated as the sum of years of life lost by premature mortality (YLL) and years of healthy life lost in states of less than fully health, i.e., years lived with a disability (YDL), which are standardized by means of severity weights, thus: DALY=YLL+YLD.WHO has established for wastewater use in irrigation (1) the same reference level of health protection as established for drinking water quality (2), i.e., the additional burden of disease from consuming water irrigated food should not exceed 10-6 DALY(Disability-Adjusted Life Years) loss per person per year (pppy). This level of risk means that a single additional case of disease may occur in a population of 1 million, during a life time (70 years). In a individual basis is equivalent to the occurrence of a mild disease during about 31,5 seconds.Such a restrictive risk is almost impossible to be attained in most developing countries which may not be able to afford the cost of wastewater treatment and of other protective measures, even for restrict irrigation.This paper presents proposals to adapt the reference level of risk to local technical, cultural, economical and social conditions of developing countries on the basis of a risk benefit approach."

Jan 1, 2008

By K. Itagaki, H. Henao

"The experimental study on the phase equilibrium and distribution of minor elements such as chromium and copper between magnesia saturated FeOx-MgO-SiO2 slag and Fe-Ni alloy were carried out under controlled oxygen partial pressure between 10-6-5 and 10-10 using CO and CO2 mixed gas at 1773 and 1873 K.The effect of slag additives such as lime (CaO/SiO2 molar ratio: 1) and alumina (AlO1.5/SiO2 molar ratio: 0.1) on the distribution behavior of the minor elements was also investigated.The value of distribution ratio for chromium, defined by (%Cr in slag)/[%Cr in alloy], is larger than 70 at the pO2 region conducted in the present study for the MgO saturated FeOx-MgO-SiO2 slag at 1773K. These value are almost 4-order higher then that of nickel though the distribution ratio of copper shows similar values with nickel. Analysis of the data indicates that addition of lime in the slag and the increase of temperature reduce the dissolution of chromium into the slag and the addition of aluminum increases the dissolution of chromium into the slag while reduces the dissolution of copper and nickel.IntroductionChromium. is a minor element in a nickel oxide ore but a Japan major component in the secondary material of stainless steel and is also introduced in the Fe-Ni production process due to dissolving bricks of a furnace. Chromium is a concerned matter for the beneficial utilization and disposition of ·slag because Cr6+ is a harmful element. Considering Fe-Ni as an alloy component in steel making, and the demand of high purity nickel, chromium is an -undesirable element that has to be eliminated into slag prior to the steel making, or the production of high temperature refractory alloys. On · the other ·hand chromium is an element of steel alloy for many applications, thus Fe-Ni containing chromium in minor element is desirable in some stainless steel making."

Jan 1, 2000

By Bruno Lebon, Koulis Pericleous, Georgi Djambazov, Mayur Patel

"High speed compressible jets are used in a number of steel-making applications. In the case of the BOF, a compressible oxygen jet reacts with a carbon-rich iron bath to reduce carbon levels and produce steel. The intensity of the process is governed by the speed of the jet and by the size and shape of the depression created in the metal and slag by the force of the jet, i.e. by the corresponding free surface. This is a difficult CFD problem, since there are compressible and incompressible regions in the flow domain, which need to be handled differently in a finite-volume (FV) pressure-correction scheme. Also, standard turbulence models do not account for compressibility, or the large difference in density between the cold oxygen jet and the hot reacting surroundings. Corrections are introduced to the k-E model to remedy this deficiency and the results are validated against experimental data. The compressible/incompressible boundary is handled through a transition region, based on Mach number.IntroductionThe deformation of a free surface by a compressible high speed jet is of paramount engineering interest, particularly for understanding the physical processes within a Basic Oxygen Furnace (BOF). In a BOF, a supersonic oxygen jet impinges on a molten iron surface, thereby creating a cavity. Oxygen penetrates the bath and removes carbon, resulting in low carbon steel [1].The challenges in modelling such a process lie in coupling a solution domain with distinct compressible and incompressible regions and in dealing with large density differences between the modelled gas and liquid. The modelling of compressibility within the jet is crucial, since the correct velocity profile in the jet is required to determine the cavity depth with accuracy."

Jan 1, 2012

By Nicholas S. Lynn

"A new process has been developed to bioleach refractory gold ores to expose the precious metal values using Thiobacillus ferrooxidans bacteria.The ore is hosted in a limestone rock with secondary replacement of carbonaceous and pyritic minerals. Crushing, stacking, bioleaching, rinsing and neutralization have been completed in a 45-day total time cycle. The use of sulfuric acid operation, and concentrated Thiobacillus ferrooxidans population allows the short bioleaching cycle.The ore is then processed using conventional Carbon-In-Leach Cyanide recovery techniques.ABSTRACT ONLY"

Jan 1, 1997

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By Berndt Moeller

Mercury-cell chlor-alkali production plants generate mercury contaminated wastewater streams from which mercury must be precipitated and filtered, resulting in a sludge containing 2% mercury (designated KI06) that cannot be landfilled in the United States without treatment. REMERC is a chemical treatment process used to recover 99% of the mercury from wastewater sludge generated at these plants. The process uses leaching to oxidize mercury compounds to mercuric chloride, washing and filtration to separate mercuric chloride from the treated sludge, and cementation to reduce the mercuric chloride to metallic mercury. Mercury not recovered in cementation is recycled to the wastewater process for precipitation and filtration. Treated sludge contains less than 260 ppm total mercury and 0.2 ppm TCLP, meeting the USEPA low mercury subcategory specifications that allow landfill disposal. REMERC uses readily available chemicals, is straightforward to control and inexpensive to operate, has no mercury emissions to air, and recovers metallic mercury. REMERC enabled significant cost savings including lower solids disposal costs, recovery and reuse of metallic mercury in the chlor-alkali process, and ability to treat non-wastewater sludge. No new EPA permits were required. REMERC was shown to be a viable process for recovery of metallic mercury from K106 designated sludge.

Jan 1, 2003