Search Documents

By Greg Dowling, Jun Ge, George Shannon, Shufeng Yang, Yongfeng Chen, Lifeng Zhang

"Inclusions in 316L stainless steel ingots poured using two different upgate designs – a traditional upgate and a swirl upgate - were investigated using SEM and ASPEX automated inclusion analysis. The main inclusions were high SiO2 inclusions, MnS inclusions and SiO2-Al2O3-CaO inclusions. More inclusions were detected at the top of the ingot than other places in vertical direction, and more inclusions were at the edge of the ingot than other place in the radial direction. With swirling upgate there were more K- and Na- bearing inclusions than that with the traditional upgate indicating possible more serious flux entrainment with the swirl upgate.IntroductionIngot casting still is very important for production of special steel grades including high carbon chromium bearing steel, thick plate, seamless tube, forgings, bars, and wire rods [1] . During the bottom teeming process, molten steel enters the trumpet and passes through the spider into the runners. Molten steel then enters the ingot mold through an upgate near the end of the runner. In the early stages of filling a mold, a mold flux bag hung in the mold were burnt and the mold flux will cover the top of the rising steel to protect the steel from being reoxidized, acting as well as act as a thermal insulator. So far, some efforts on studying inclusions characteristics in the ingot have been reported. A review paper on the control of inclusions during steel ingot casting was published by Zhang et al. [2] Zhang also studied Inclusions in bottom-teemed ingots of plain carbon steel and found that the >20µm inclusions originated from either the entrainment of mold flux of the reoxidation during teeming process. [3] The results of Nagendra and Du showed that there were more inclusions in the centre part of the ingot [4]. Eriksson et al reported that the composition of inclusions was more complex in the mold samples in comparison to the ladle samples, and more inclusions in the mold were found than in ladle because of the reaction between the mold flux and the molten steel [5]. It was reported that SiO2-CaO-Al2O3 inclusions originating from mold powder with reoxidation product Al2O3 as a part, and there were more inclusions close to the side wall than the center of the ingot in the radial direction. [6]. A more recent investigation showed that four main types of inclusions in runner samples were classified: oxides, sulfides, complex and carbon-nitrides. [7] The flow pattern in the mold during filling has been found to be an important factor regarding inclusions in the ingot. In the early stages offilling a mold, steel enters the mold through the entry nozzle at a high velocity. The effect of the resulting turbulence on the meniscus can lead to the entrainment of mold flux. Efforts have been paid over the years to find methods to reduce the velocity of the molten steel entering the mold, such as using opening angle of the inlet nozzle [8], using swirl blade at the runner [9], using a divergent nozzle combined with a swirling flow generated in the nozzle [10-11]."

Jan 1, 2012

By Federica Paglietti

In this work is presented SEX (Structural & Elemental X-Ray Instrument), the first spectrometer completely portable which make non-destructive X-ray fluorescence and diffraction analysis, in contemporary and in real time. This instrument has been realized using miniaturized detectors, the same model installed on the mission Pathfinder NASA, and X-ray microtubes. SEX allows the chemical and mineplogical characterization of all kind of solid materials and allows to make chemical stratigraphy and liquids analysis.

Jan 1, 1998

By Ali Akbar Mottahedi

Chromate conversion coating is a process for making a complex layer at the surface of zinc galvanized steel which makes the metal more resistant to corrosion, especially at marine atmosphere, and increases the adhesiveness of color. In this work the influences of various compositions on commercial zinc galvanized steel sheet to the color of chromate conversion coating has been investigated at normal temperature and the factors that affect the control and optimization of the process have been determined. A bath composition of 20 g/liter Cr203 and 10 g/liter NaOH and a dipping time of 50 seconds at room temperature (25-30°C) make a desirable color of chromate coating. A slow agitation at a constant pH of I (with additions of NaOH or H2SO4) assures a constant bath condition and develops the color. This kind of coating has more corrosion resistance and this bath condition and composition are also more economical.

Jan 1, 2003

By M. Potesser

After the primary or secondary lead production the bullion lead is remelted and charged into a vessel with following refining process. The removing of arsenic, antimony and tin takes place by salt slags or oxidizing gases like air or pure oxygen. Due to the increasing lead price, Messer Austria GmbH in cooperation with the institute of Nonferrous Metallurgy at the University of Leoben have developed a new process named OXIPOT for the refining of tin, arsenic and antimony. The OXIPOT process is in principle based on purging technology with a ceramic or steel purging device. This leads to an increased retention time of the refining products due to the deeper bath level and an optimized specific reaction volume concerning the bubble size. This paper describes the process, pilot plant, and thermodynamic calculations for the optimization concerning the selectivity of element removal.

Jan 1, 2008

By Sadi Medina

As it is characteristic from Custom Smelters, ENAMl Las Ventanas Smelter has to deal with different qualities and quantities of mining products from about 70 suppliers, that contain a variety of impurities that would be harmful for copper production. In order to increase the smelting capacity, an oxygen plant has been running since September of 1990. Moreover, to improve the environmental conditions, a new sulphuric acid plant started up to neutralize the metallurgycal off-gases from the Teniente Converter and partially from the Peirce-Smith converters. Based on the on-line operation among the reverberatory furnace and the Teniente Converter using oxygen enriched air to produce high grade matte, most of the volatilizing impurities, mainly arsenic, are collected as discarding compounds in the gas cleaning system of the acid plant. This paper describes the continuous performance of the Teniente Converter with acid plant, the results attained, the operation problems and how they were solved. The impurities distribution achieved in this process is also included.

Jan 1, 1993

By J. C. DeSantis

Thin, highly reflective rhodium films with metal compositions greater than 98% (elemental -weight percentage) have been deposited by chemical vapor deposition using Rh(allyl)3 (ally1 = q3-C3H5) in the presence of a hydrogen plasma. Uniform, crystalline films that adhere well to several types of substrates result from depositions at temperatures as low as 150°C. Depositions using H2 (no plasma), or an argon plasma yields material that is amorphous, contains a significant amount (>14%) of residual carbon, and has a dramatically slower growth rate. The composition of these materials does not vary significantly from that of the materials obtained from the in vacuo thermal deposition with Rh(allyl)3.

Jan 1, 1992

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By G. Belardi

A study has been conducted to assess a new wet beneficiation treatment for the recovery of the sulphuric-acid-soluble titanium oxide contained in the waste from an Italian TiO2-pigment facility. The waste is produced during treatment of a Ti-enriched slag and contains as main components TiO2 (54%, of which 42% acid-soluble and 12% insoluble), SiO2 (27%) and A1203 (6%). Eighty percent of the material is finer than 50pm. The first step was to ascertain the possibilities offered by size classification, wet gravity separation, froth flotation and wet high-intensity magnetic separation to improve the grade and recovery of Ti02 and reduce the SiO2 content. The next step was to optimize the operating conditions of the various separations and assemble them into a complete flow- sheet. Beneficiation ensures potentially 70% recovery of the TiO2 with a concentrate grade of 80%.

Jan 1, 1998

By Tae-Hyun Kim, Kang-In Rhee, Jeong-Soo Sohn

The synthesis of Mn-Zn ferrite powder from spent zinc-carbon batteries was investigated using a series of physical treatment, sulfuric acid leaching and coprecipitation. Physical separation methods such as crushing, magnetic separation and sieving were applied to generate a non-magnetic material of 8- mesh undersize for subsequent leaching process. The 8-mesh undersize of the spent zinc-carbon batteries was assayed 23.9% Mn, 14.9% Zn, and 4% Fe. Metal extractions obtained in sulfuric acid leaching at the solid/liquid ratio of 1:10, 2 M H2SO4, and 60? with 6 vol.% H2O2 addition were 97.9% Mn, 98.0% Zn and 55.2% Fe. The leach liquor was finally adjusted to the Mn:Zn:Fe mole ratio of 1:1:4 suitable for producing MnZnFe4O8 ferrite powder by the addition of Mn, Zn and Fe sulfates followed by pH control. A co-precipitation test for Mn-Zn ferrite powder was performed at 80?, O2 gas flowing at 1.3 L/min. As a result of co-precipitation, Mn-Zn ferrite nanoparticles in 20 nm size with spinel structure were successfully synthesized. The saturation magnetizations of Mn-Zn ferrite powder (Mn1-xZnxFe2O4) were determined to be 39-91 emu/g with various zinc contents (X=0.2-0.8).

Jan 1, 2008

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By Andrey Tarasov, Erki Unn, Valery Paretsky

"The stability of the markets of energy resources and labor in countries of the Baltic Sea Region including Estonia is determined to a significant degree by the use of combustible shales as fuel and their distillation resulting in generation of up to 70% of non-recyclable waste. The objective of this business plan is to substantiate the investments for establishment of a new facility in Estonia for waste-less and environmentally safe processing of fossil minerals and man-made products generated in the shale industry, as well as other hazardous wastes. The proposed facility will use a basically new waste processing technology developed in Russia - i.e., processing in sparged molten slag This technology eliminates any release of harmful pollutants to the environment and a facility using this technology does not require, therefore, any sanitary protection zone.IntroductionIn the Baltic region, and first of all in Estonia and some other European territories, there are large natural deposits of combustible shale, which due to the lack of other own resources of energy and hydrocarbons for the chemical industry is burned and distilled with low technical and economic efficiency generating large amounts of toxic and highly toxic wastes and intermediate products. Currently, the penalties for disposal of such wastes have grown to such an extent that shale burning and distillation might become unprofitable. This might result in suspension of the given operations, which in turn will affect in an adverse way the markets of energy resources and labor market in those countries. Furthermore, in addition to the “shale problem”, Estonia, similarly to most member countries of the European Union, faces the challange of environmentally safe processing of highly toxic wastes, such as municipal solid wastes, oilpolluted materials, medical wastes and infected materials, spent rubber tires, etc. These wastes are at present stored or processed with release of a significant quantities of extremely toxic cancerogenic substances (dioxins, furans) or collected and exported for treatment at an extremely high cost and with a loss of valuable components contained in these types of waste and often with return of supper toxic processing products."

Jan 1, 2008

By Yuzo Hiroshige, Kiyotaka Tahara, Hiroki Hatayama, Masaharu Motoshita, Tomohiko Akahori

Large amount of rare earth metals is stored in the used electric products. Hitachi has started to develop the environment-friendly process for rare earth metals recovery from used magnets. We report here the environmental impact of our process, in comparison with the conventional recycle process utilizing solvent extraction. As an evaluation method, Life-cycle Impact assessment Method based on Endpoint modeling ver.2 (LIME2) developed by the National Institute of Advanced Industrial Science and Technology (AIST) in Japan is applied. It was found that the environmental impact of the new process was more than that of the conventional process. For further reduction of its environmental impact, minimization of energy consumption to operate the equipment was most effective. Decreasing the amount of magnesium, used as an extractant, and the improvement of the extraction rate of rare earth metals were also considered as specific options for reducing energy consumption in the plant development.

Jan 1, 2014

By Peter J. Koros

The current wave of interest in this topic is the result of increased use of titaniferous ores or ilmenite in blast furnace burdens for the purpose of repairing hearth damage. The titanium compounds that promote deposition of ?patching? materials in blast furnaces are the cause of downstream problems in the steelmaking shops. Steelmakers historically have objected to significant amounts of titanium in hot metal (>0.10 % Ti) for several reasons: 1) accretions caused by the TiC.TiN needles that float out of the iron as it cools in transit and in transfers make the accompanying slag sticky and crusty, causing problems in desulfurization and increasing time and Fe yield loss at the subsequent raking, 2) defensive measures have been taken in treatment, such as use of argon for carrier gas, but without technical rationale for this approach, 3) difficulty in removal of the ladle slag by the raker, with subsequent sulfur addition to the vessel charge, and 4) transfer into the BOF and/or formation of a very corrosive TiO2 containing acid slag during the early part of the BOF blow which, in addition to causing lining damage, results in loss of sulfur removal capability by the vessel slag. Based on a conceptual analysis of the metal-slag-atmosphere interactions during transfer ladle desulfurization treatment, a mechanism is postulated for the apparent effectiveness of the use of argon in reducing the deleterious effect of titanium and an alternate technique, possibly more effective, is proposed. As probably the use of argon causes increased exposure to atmospheric oxidation of the titanium carbonitrides contained in the ladle slag, the same benefit can be obtained by use of either oxygen or an air blast to oxidize the noxious reaction compounds. Validity of the concept has been demonstrated in a pilot plant setting. These issues, and related effects on testing the hot metal, are examined in detail with reference to the literature and plant and laboratory experience.

Jan 1, 2006

By J. H. Lee

LG Metals Corporation started its second smelter operation at Onsan along with the existing flash smelter on January 31, 1998. Onsan smelter has been producing about 140,000 tons of copper annually from concentrates with the flash smelting line since 1979. In accordance with an increase in domestic copper demand, LG Metals Corporation decided to expand smelting and refining capacity by introducing a second smelter line using the Mitsubishi continuous process and a new tankhouse in 1995. After two years' expansion works consisting of engineering, procurement, construction and a successful commissioning test, the total smelting capacity of Onsan smelter increased to 340,000 ton of copper annually from concentrates. This paper describes the smelting facilities, operation result, problems encountered and improvements during the start-up and early operation of Onsan's new smelter

Jan 1, 1999

By Elli Miettinen, Markku Lahtinen, Ilkka Kojo

"The recent trends of decreasing energy consumption and environmental emissions and utilization of economies of scale are strong drivers favoring continuous copper converting processes. Flash Converting benefits from low off-gas volumes and low investment and operational costs for off-gas treatment. Separate matte and blister furnaces allow the adaptation to concentrate quality changes and flexibility in layout and maintenance.The stationary blister copper bath in Flash Converting furnace is less aggressive to the furnace linings than agitated processes, resulting in low refractory consumption, long campaign life and high on-line availability.Copper Flash Converting has been successfully applied in Kennecott with a campaign life now exceeding five years. A second FCF was started at Xiangguang Copper in China in 2007. The process itself is proven, as its features are similar to those in FSF, Direct-to-Blister and Direct Outotec Nickel Flash Smelting (DON), with one significant difference: it is the easiest of all to operate.The paper presents differences between continuous Flash Converting and conventional converting based on recent experiences and studies."

Jan 1, 2009

By C. Frias, M. Garcia, G. Diaz

Advances in hydrometallurgy promoted by Tecnicas Reunidas are providing increasingly simple and clean means for controlling the entire lead recycling chain. Used in parallel with pyrometallurgy, these processes allow furnace temperatures to be reduced and fumes and atmospheric pollution to be minimised. Furnace slags are digested, and residues (mainly gypsum) are non-toxic and convertible into marketable products. In addition, the global economy of the process is substantially improved by reducing the operating cost, increasing the lead recovery above 99% and obtaining a 99.99% pure lead product. These new PLACID and PLINT processes may provide the cleanest and healthiest practicable means for recycling lead from batteries.

Jan 1, 2000

By Yingtao Zhang, Shaofeng Du, Yiming Rong, Wenjun Zhao, Gang Wang

"20Cr2Ni4A steel is a kind of high quality steel mainly used for manufacturing high-duty gears in the world. The high-duty gear with good performance must have wear and fatigue resistance properties. In order to get the good properties, the high-duty gear needs a high hardness gear surface and a good hardness gradient along the depth direction. In this paper, the samples were designed and a vacuum carbonitriding process was put forward to improve the surface hardness of parts for 20Cr2Ni4A. The process contained carbonitriding, quenching, cryogenics, and tempering process. The surface hardness and hardness gradient of carbonitrided samples were measured and the good microstructure was gained. The surface hardness is 67.SHRC and the case depth is 1.2mm.IntroductionSteels are widely used in industry, but the fatigue strength and the wear resistance of steel is much low. So the heat treatment process is put forward to improve the mechanical properties of steel. It can be improved by high-energy heat treatment methods for medium-carbon and highcarbon steel. Those methods will not alter the chemistry of the base metal [ 1].For low-carbon steels, carburizing and quenching should be used to improve the steels' mechanical properties, especially the surface properties. Compared with the carburizing, carbonitriding has more advantages, such as a short production cycle, low temperature and small deformation of parts. Carbonitriding is a modified form of gas carburizing, rather than a form of nitriding. The modification consists of introducing ammonia into the gas carburizing atmosphere to add nitrogen to the carburized case as it is being produced. Nascent nitrogen forms at the work surface by the dissociation of ammonia in the furnace atmosphere; the nitrogen diffuses into the steel simultaneously with carbon. Typically, carbonitriding is carried out at a lower temperature and for a shorter time than is gas carburizing, producing a shallower case than is usual in production carburizing [2]. As a material surface strengthening technology, carbonitriding has been widely used in the production [3]. And vacuum carbonitriding process is better than carbonitriding, because the vacuum carbonitriding temperature can be higher than carbonitriding without surface oxidation."

Jan 1, 2014

By J. Chen Kuriyama

One method to store hydrogen effectively involves the use of metal complexes such as the alkali-element aluminum hydrides. The hydriding/dehydriding properties of these materials depend on how to prepare them with different structures and microstructures. The present work focused on a high-energy ball milling technique to produce Ti-doped lithium tetrahydridoaluminate (LiA1H4) and lithium hexahydroalanate (Li3AIH6) powders with nanocrystallites. The phase structures and dehydriding/rehydriding characteristics were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller measurement, thermogravimetry, and differential scanning calorimetry. The mechanism of dehydrogenation and rehydrogenation was also examined by means of X-ray photoelectron spectroscopy (XPS). The results on the relation between the reversible hydrogen storage and catalysis function of the Ti-doped complex hydride indicate that both the homogenous distribution of Ti+AI nanoclusters and the Ti¬catalyst with Ti e> Ti3+ (Ti0/Ti2+/Ti3+) defect sites play important roles in optimizing the reversible hydrogen storage.

Jan 1, 2002