Search Documents

By Hiroshi Nakajima, Kotobu Nagai, Toshihiro Hanamura

"Low carbon ferritic steel bars with ultra-fine grain structure was developed through a warm rolling for the first time by the present authors. They show better low temperature toughness than conventionally hot-rolled plates. Hence, the brittle fracture surfaces in Charpy tests were examined in terms of the effective grain size of fracture, compared with those of conventional QT steels. The ductile-to-brittle transition temperatures were in good accordance with those for the QT steels if referred to the effective grain size of fracture: · However, the size was a few times that of the ferrite grain. This means the grain refining is not yet fully utilized from the viewpoint of low temperature toughness. The anisotropy of· the impact properties and the annealing effect of highly dislocated structure on the toughness are also discussed in the present paper.IntroductionFor structural materials, both high strength and good toughness are required. Well-known approaches for obtaining better toughness for steels are as follows:1) Grain refining2) Addition of Ni3) Thin plate effect by cracking parallel to the rolling direction prior to crack propagation4) Contribution of metastable austenite.Among them, only the grain refining can raise the strength and improve the toughness. And it is well known that the finer the ferrite grain size, the lower the ductile-to-brittle transition temperature. For example, in the case of 0.11 carbon steel, the transition temperature decreases linearly to in d 1/2 [1 ]. However, these have been told in the regime of coarse grain size that is larger than 10 µm in diameter. There ~as .been no study dealing with the low temperature toughness in the regime of ultra-fine grain size with a diameter in the order of 1 µm."

Jan 1, 2000

By I. S. Escobar

Copper, particularly the oxygen-free grade Cu-OFP, is a candidate material for containers for the long-term isolation and disposal of high-level radioactive waste (HLW) in underground repositories. After having been buried for a few hundred years, all oxygen will have been consumed in the repository, and corrosion of the copper will be caused entirely by contact with dissolved sulfides. Chloride is another potential corrodant, but in deep repositories where groundwater is neutral or slightly alkaline, the effect of chlorides can be ignored on thermodynamic grounds. Thus, the corrosion of copper in the presence of sulfide ion and under reducing conditions has been studied using cyclic voltammetry and Tafel slope measurements. It is possible to determine the effect of sulphide ion on copper corrosion resistance which is minimized at low temperature and also at low sulphide concentration. The presence of anions such as HCO3 under environmental conditions produces a beneficial effect because these ions are inhibitors.

Jan 1, 1999

By R. Gampala

The consolidation of mom matrix composite monotapes occurs by the plastic (time independant) and creep deformation of monotape asperities. Past models of the process used seperate micromechanical analyses of the contact deformation by (rate independent) plasticity and power law creep (i.e steady state creep). These models are now used to simulate consolidation and to optimize/control consolidation process cycles so that the composite's microstructure is "steered" to, a user defined goal state. However, the models do not incorporate the sometimes dominant transient creep process and the instantaneous response of the plasticity mechanism causes finite discontinuities in the microstructure state vector field and therefore eliminates the possibility of using the powerful array of trajectory optimization schemes that all require continuous vector field for optimization and control. To overcome this problem, a inified creep/plasticity constitutive model that results in a continuous state vector field is used to rederive the contact deformation response during monotape consolidation. The contact blunting of a laterally constrained hemispherical asperity is first analyzed and its response represented by two coefficients; one relating the contact area to the blunting strain (C), the second, the mean contact pressure to the blunting rate (F).The C and F coefficients for this unified blunting problem are then obtained by finite element analysis, and detailed results presented for two composite matri-ces of topical interest (Ti-24A1-11Nb and Ti-6Al-4V).

Jan 1, 1996

By Ricardo Ponce

In recent years, ENAMI implemented modernisation plans at its two smelters in order to meet the government's environmental regulations introduced in the early 1990s. The modernisation plans defined the new SO2 and particulates emission targets, deadlines for compliance, and the revised treatment capacities of the smelters. At Las Ventanas smelter, the principal process change consisted of eliminating the reverberatory furnace. All the smelter feed is currently processed in a 4m diameter, 14m long Teniente Converter, using up to 34% oxygen enriched air. Dry concentrate is injected into the bath through tuyeres. A fuel oil burner compensates for any process heat deficiency. The Teniente Converter high copper content slag is cleaned in an electric furnace. This furnace is also used to melt internal reverts. This paper will discuss the successful operation of the slag cleaning electric furnace.

Jan 1, 1999

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003

By M. Giralico

Optimized mixer settler designs will now handle flows of over 25,000 GPM. The size and expense of the equipment hamper experimental settler optimization efforts. Computational Fluid Dynamics (CFD) is a timely and predictable tool for settler design development. In the past, CFD has been used to evaluate only the flow field in pumped and auxiliary tanks. A similar numerical analysis is used to evaluate settler flow and phase separation. Phase separation is analyzed using multiple species for the aqueous and organic phase. Experimental validation shows good agreement between the computational and experimental solutions in both flow field and phase separation. The computational model is used to show performance differences between various choices of settler geometry, liquid depth, with variable flow rates. Understanding the differences allows the development of optimized settler designs. System improvements are predicted to lower entrainment levels further and/or allow new smaller footprint designs. This paper focuses on the major design components of the settler and how future technological advances will lead to further improvements in their design. LIGHTNIN?s new designs will handle tomorrow?s production requirements, while maximizing profits.

Jan 1, 2003

By M. Suzuki, M. Dobashi, M. Kahata, T. Yoshida

Almost 30% of steel in Japan is produced by electric arc furnace (EAF) treatment of iron scrap. EAF dust includes approximately 20 wt % of Zn and 3- 5 wt % of CI and is treated by the pyrometallurgical processes to recover Zn as Zn oxide. Direct hydrometallurgical processing is one of the most effective methods to recover high purity Zn. In this case, CI in the EAF dust is dissolved in the liquid phase by leaching, and the CI anion in electrolyte attacks anodes which are commonly made of a lead base alloy. Several processes have been proposed to remove CI anions from acidic sulfate solution. In this study, an electrolytic process was examined to eliminate CI anions from Zn sulfate electrolyte. From our study it can be said that the elimination rate of CI anion depends on the anode material ( i.e., the elimination rate is Pb-Ag alloy == Pb > DSE== Pt). In industrial Zn electrowinning process, the electrolyte contains Mn, which means the influence of Mn should be considered in the elimination of Cl. Mn dioxide deposition on an anode plate reduces the efficiency of CI removal. A periodical reverse current electrolytic system was examined to prevent this efficiency decrease, and deposited Mn dioxide could be removed very rapidly when the current is reversed. More than 95% of CI anion could be removed by this method in a shorter period than direct current method.

Jan 1, 1997

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Ragnhild Aune

In fire refining of copper, the affinities of various impurity elements on dissolved oxygen is of great significance. Further, in the design of oxygen probes in liquid copper, the influence of solute interactions on the activity of oxygen need to be considered in order to evaluate the oxygen concentration in molten copper. The present paper presents a series of measurements of the activities of oxygen in liquid Cu-M-o alloys (where M stands for Mn, Zn, As, Se or Te) carned out by the present group employing the solid electrolyte galvanic cell technique. Extreme care was taken to control the oxygen potentials in the inert gas atmosphere, and to keep the oxygen levels very low in the molten metal. The oxygen content was determined by analysis of the samples taken out from the melt. The results obtained showed that Mn has a strong negative influence on the activity coefficient of oxygen in liquid copper. A similar, but less prominent effect was observed in the case of Zn. Arsenic had no influence on the activity of oxygen in Cu (liq.). Se and Te had slight negative effect on oxygen activities in copper at XQ >10-5, while at lower oxygen levels the interaction coefficients were found to be positive. The results obtained were compared with empirical models for the calculation of interaction coefficients available in literature.

Jan 1, 2003

By Jin Liu

To improve value metals recovery, a new operating concept for the Inco flash furnace was investigated, in which the flash furnace coke addition practice would aim at establishing a reducing barrier on the surface of the molten bath. The descending partially oxidized sulfide mineral particles would reach the supernatant coke layer prior to the formation of slag. The key for success depends on the effectiveness of the coke layer to produce a sulfur deficient matte while maintaining furnace production capacity. The mechanism and rate of carbon reduction of the phases formed in the flash flame, i.e. sulfide (matte) and oxysulfide was investigated by means of crucible graphite reduction test work. The objective of these tests was to measure the rate of solid graphite reduction of matte, oxysulfide, slag, and matte+slag mixture at different temperatures. These tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions, reduced material assays, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006

By Matti Hämäläinen

Outokumpu has developed a new chloride leaching process, HydroCopper?, for copper concentrates. The process utilizes the cupric ion as oxidant, which is able to dissolve chalcopyrite. After solution purification monovalent copper is precipitated as cuprous oxide, Cu2O, using sodium hydroxide. Copper product is produced from Cu2O by reduction, melting and casting. An essential part of the new process is chlor-alkali electrolysis, which regenerates the reagents used. All impurity metals are removed before Cu2O precipitation, because otherwise they would report to the copper product, impairing its quality. A multistage solution purification scheme has been developed consisting of firstly, chemical precipitation of impurity metals by pH increase, secondly, cementation of silver and thirdly, removal of trace multivalent ions using ion exchange. This paper describes the characteristics of solution purification in the HydroCopper? process based on the laboratory tests and pilot runs made by Outokumpu Research Oy.

Jan 1, 2003

By M. Yoshida, S. Hanada, T. Takasugi

"A study has been conducted to examine the effect of ternary alloying elements on high temperature deformation of the C15 NbCr2 based intermetallics in Nb-Cr-X (X=V, Mo and W) alloy systems, which have attractive properties as high temperature structural materials. The high temperature deformation of the C15 NbCr2 intermetallics can be improved by two alloying methods. One method is based on geometrical consideration for site occupation and atomic size factor of component elements and additive elements in the single phase C15 lattice; addition of Mo and V can promote dislocation movement without introducing significant hardening. The other method is based on microstructural modification through ternary alloying; moderate addition of these elements results in a variety of duplex microstructure consisting of the C15 phase and bee solid solution without forming any intermediate phases, and can enhance the high temperature deformability. Particularly, alloys with duplex microstructure equilibrating with Cr-rich bee solid solution is shown to exhibit superior deform ability. Also, lattice property of the additive atoms in the C15 structure and phase relation between the C15 structure and the bee solid solution are investigated by OM, XRD, TEM and ALCHEMI observations and then discussed in association with observed mechanical behavior.IntroductionLaves intermetallics with AB2 stoichiometry belong to the largest group in a large number of intermetallics with various kind of crystal structures, and have a variation of the cubic CIS, the hexagonal C14 and the dihexagonal C36 structures, depending on stacking sequence of XYZ type, each of which consists of four interpenetrating atomic layers (1-3). Some of the Laves intermetallics have good functional properties and therefore are considered to be used as, for instance, magnetic materials, magneto-optical materials, hydrogen storage materials and superconducting materials (2). Also, the Laves intermetallics are considered to be good candidate as high temperature structural materials operating at high temperatures and in severe environment because they have high melting point, low density, and potential resistance to corrosion and oxidation. However, the Laves intermetallics are very brittle at low temperatures because they consist of complex crystal structures similar to many other intermetallics."

Jan 1, 1996

By Ashok D. Dalvi

Production of nickel from laterite ores has occurred for over 100 years beginning with processing of garnieritic ores from New Caledonia. However, until now the world nickel supply has been predominantly from sulfide sources. Going forward, the authors project that the production of nickel from sulfide ores will remain more or less constant. Most of the expansion in nickel production capacity over the next ten years will come from processing of laterite ores. Thus the capital and operating costs of new laterite projects will have significant impact on the nickel supply and therefore price. The authors have reviewed the history and capital and operating costs of various recent laterite projects and capital and operating costs of these projects and those "on the drawing board". The authors have also evaluated the risk associated with such projects. The paper will discuss the impact of this and the recent history on the future development of laterite nickel projects.

Jan 1, 2004

By A. Niedbalska

A technique was developed for low pressure diamond synthesis using a specially prepared glassy carbon. The glassy carbon is produced in the form of solid plates by slow carbonization process of phenol formaldehyde resin interrupted at temperatures of 1273° K, 1073° K, and 923° K. The diamond synthesis is performed using cobalt plates as a catalyst-solvent. Synthesis was carried out at applied pressures of 6.0 and 3.8 GPa and a temperature of 1970° K and 2170° K. The products were analyzed by the x-ray powder dyffraction method and by microprobe to identify the diamond crystallites. The samples were taken from the place of contact between the glassy carbon and the cobalt catalyst. They were separated from the charge by a chemical method. Diamonds of the best form and the largest size were obtained at pressures that were much lower than those used in the traditional graphite method of diamond synthesis.

Jan 1, 1989

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Grigore Matei

The thermodynamic properties of CU2S-FeS system are important not only in the case of copper smelting but also in the case of general pyro-mctallurgy, However there are not many reported activity data In this study, activities of FeS and CU2S in the CU2S-FeS system were calculated using the Darken's method from the activity data of the CU2S-FeS-Sb2SJ systems measured by the transportation method at 10S0°C. The activities of CU2S and FeS in the CU2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation,

Jan 1, 2003

By Animesh Jha

Univariant diagrams are constructed for the reduction of nickel and cobalt oxide and sulphide minerals. The results from the carbothermic and hydrogen reduction of sulphide minerals are compared. The importance role of lime and calcium sulphate in controlling the emission of sulphurous- gases during reduction reaction is also explained. The mechanism of carbothermic reduction of nickel sulphide is explained by examining the sulphur exchange and reduction reactions. The phase equilibrium relationships that determine the formation of multicomponent liquid are characterised. Also the governing equilibria for inert atmosphere calcination- roasting of nickel and cobalt sulphide minerals are also described for the metallization of nickel and cobalt.

Jan 1, 1993

By Sergio Sanchez-Segado, Yuan Zhang, Animesh Jha, Ahmad Fahmi Ruzaidi

Niobium and tantalum are considered critical materials because the increasing demand in the energy sector which is reliant on limited abundance of these two metals in minerals. Traditionally, niobium and tantalum mineralsare digested using hydrofluoric acid at moderate temperatures, producing oxy-fluorides which are separated by solvent extraction, involving the use ofhazardous chemicals. The increasing environmental pressures are forcing the industry to search for alternative low carbon processing methods. In this paper alkali roasting based separation and beneficiation, which is not well understood in the literature, is proposed, for which the kinetics and thermodynamic equilibria for the formation of sodium tantalate and niobate with sodium hydroxide are analyzedat the temperature range of 400ºC to 700ºC. The apparent activation energy of formation,changes from 31.0±0.8 to 22.3±1.2 kJ mol-1 and from 23.8±1.2 to110.2±12.8 kJ mol-1, for tantalate and niobate, respectively. The reaction mechanism is examined on the basis of the analysis of reaction products using X-ray powder diffraction (XRPD) and X-ray fluorescence (XRF).

Jan 1, 2015

By Katsukiyo Marukawa, Mashamichi Sano, Shigeta Hara

"Various subject of studies are discussed to develop ·innovative refining processes in the 21st century for cost reduction, production of high quality steel and environmental conservation. The future refining reactor should have abilities of highly efficient mixing and separation of different phases. It is stressed ·that applications of electromagnetic and ultrasound energies, and control of flow fields rate required to create the highly efficient mixing I separation reactor.IntroductionIn recent years, it seems that the research and development in the field of steelmaking has shifted its emphasis to the solidification I ingot-making process in which continuous casting plays the leading role. From a long-range point of view, however, the need for continual development of the refining process will probably increase but is very unlikely to decrease. In order to meet such demands, it is required that problems and issues of the present process should be clearly grasped and that there must be rapid progress in process elements, such as highly efficient mixing and separation of different phases.Applications of electromagnetic and ultrasound energies and flow field control will become important options for resolving the above-mentioned problems. By efficiently and skillfully incorporating these new technologies into high-efficiency mixing/separation reactors, the innovative refining process will be established in the early 21st century."

Jan 1, 2000