Search Documents

By D. Kolymbas

A simple formula is introduced which allows the evaluation of dynamic pile tests. The following case is considered: The pile top is dynamically loaded by an impact. The velocity v of the pile top is recorded over the time. Let v1 and v2 be the first and the second maximum of this curve. Then, the pile bearing capacity (resulting from ideally plastic resistance at the pile wall and at the tip) can be set approximately equal to Z(v1- ½ v2), where Z is the impedance of the pile cross section. Due to the assumption of ideal plastic resistances, radiation damping needs not be taken into account. Material damping may be important in rate sensitive soils (such as clay, even if it is highly overconsolidated). A simple correction procedure for material damping is proposed.

Jan 1, 1989

By Richard Pizzi

Built in 1806, Boston's African Meeting House is the oldest surviving Black church building in the country. A $7 million dollar renovation was begun in 2006 to restore this historic building to its 1855 appearance and to modernize the building's accessibility, electrical and mechanical systems. As part of the restoration, an underground utility room and elevator tower, needed to provide handicap access to the Meeting House, were constructed. Extending up to 17 feet below the foundations of the abutting buildings, the utility room was constructed within one foot of some of Boston's oldest and most expensive residences. All equipment and materials had to enter the work area through a narrow alley rendering conventional methods of excavation and construction of earth support using heavy equipment unfeasible. A unique combination of micropiles, structural cap beam, internal struts and shotcrete facing was designed and constructed to provide the permanent and temporary support of the lateral loads from the earth pressures and adjacent building surcharges and the vertical loads from the elevator tower. The narrow and congested streets of the Beacon Hill neighborhood presented many day-to-day challenges for the contractor.

Jan 1, 2011

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

By Z. Q. Zhou

It is the first worke in design of pile foundation to determine the carring capacity of single pile, and a static loading on site is considered to be the lost derect and reliable way. All values P and settlements S induced can be plotted as a broken-line. Since soil is a kind of elasto-plastic and cohesive material, the increasing of settlements is generally greater than that of loads. Different value Pu nay be given by different tester on his P-S diagram, because of erroys in the test and complicated, characteristics of soil. The analytical method of exponential equation shown in this paper derives a specified solution. After using an exponential curve to regress values of loads P and corresponding settlements S from on-site test, coeficients A and B of exponential equation can be obtained. With this curve an ultimate carrying capacity of single pile can be determined. The resistant forces of pile shaft and pile tip can also be defined by the tangent of the calculated knee point, as it is called (tangent method). At last, an example is given to show how the ultimate carrying capacity of f 500mm bored pile is obtained with this method for a project in Kunming.

Jan 1, 2010

By Jay L. Hodkinson

Replacement of an aging twin span river crossing in Vermont required a temporary bridge to accommodate traffic during construction. Soils beneath the temporary approach embankment consisted of very soft organic clayey silt underlain by interbedded, loose alluvial fine sand and silt/clayey silt. Reinforcement was required for the southern temporary approach embankment to limit settlement and to increase global stability factors of safety. A ground improvement design was developed using Rammed Aggregate Pier® reinforcement and was included in the contract documents as an FHWA Category II Experimental Feature. Instrumentation intended to document the performance of the supported embankment was installed. Piers were then constructed and monitoring commenced as embankment and bridge construction occurred. Weekly instrumentation data reports indicated continuing excess pore water pressure, settlement, and lateral deformation of the subgrade soils as the embankment and temporary bridge abutment was constructed. In response to the unanticipated monitoring results, further investigation indicated that significant deviations from the conditions and basis upon which the ground support design was developed were made during construction. This paper discusses these deviations and their specific impacts to embankment support performance, how these deviations occurred, the role that the ground support system played in maintaining global stability, measures taken to limit further detrimental impacts to the embankment, and provides recommendations for contract document preparation and construction oversight to prevent similar situations from occurring on future projects.

Jan 1, 2011

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014

By Takashi Saito

Since early 1970?s skirt suction foundations (skirted foundation / bucket foundation) have been used as support for large fixed substructures or anchors for floating structures in offshore hydrocarbon development projects. In recent years skirt suction foundations are recognized as one of the solutions in foundations applicable to bridge substructures installed in waters, because skirt foundations have a wide variety of functions such as control of settlement during service life, less impact to environments during operation at installation site. This paper introduces general features of skirt suction foundations, and then discusses design practice of them for the application to bridge substructures, with reference to experiments in both laboratory and field.

Jan 1, 2013

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By Andrzej Tejchman

Calculation of pile foundations should possibly truly reflect its real work, mainly with respect to the value and distribution of settlements, pile internal forces and bending moments within a slab. Many empirical and theoretical methods serving for an assessment of the settlements of pile group overestimate its actual values obtained from field measurements (see Tejchman et al., 2001). In the paper a simple engineering method for calculation of pile foundations is presented. The method takes into account the interaction between the slab and a soil together with the phenomenon of non-uniform deformation of the soil-pile subsoil, particularly under large foundations. In the method the scheme of the slab resting on one-parameter elastic subsoil is assumed. The comparison of the calculation results for existing pile foundation with the field measurements shows good agreement between those values.

Jan 1, 2002

By M. T. Davisson

Pile compression load capacity prediction methods are divided into four categories for purposes of discussing their reliability compared to static load test results. The categories considered are: 1) static analysis, 2) driving formulas, 3) wave equation analysis, and 4) dynamic measurement and analysis. It is concluded that any method of static analysis that works for the geological deposit in question may be satisfactory. However, any given method can be quite wrong when applied to other deposits of soil that are different in terms of their engineering and geological characteristics. Dynamic formulas are found to be theoretically unjustifiable. The ready availability of the wave equation analysis for microcomputers eliminates the need to utilize dynamic formulas. The wave equation analysis is found to be the best analytical method for making predictions both for design and for construction control. Dynamic methods of measurement and analysis are found useful, but have limitations that have caused troubles on many projects. Two case histories are presented that show the limitations of dynamic measurement and analysis, and of the wave equation analysis. Soil deposits exist that defeat both the wave equation and dynamic measurement techniques; static load tests are currently the only method of proving the load capacity of piles in such soils.

Jan 1, 1991

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006

By Madan Kumar Annam, Hari Krishna Y

"Basement construction is one of the challenging geotechnical concerns in the urban environment. Several types of retention systems are practiced to support the earth which is suitable for restricted access, rapid mobilization, fast excavation and cost-effective designs. A thorough understanding of geotechnical engineering as well as the structural mechanics is important for the earth retention systems. This paper discusses a project with various types of foundation solutions including monitoring of deflections during excavation stage of a retention system.A multi storeyed residential building (3B+Stilt+18F) in Chennai having structure foot print area of 1500 m2 has to be constructed on large diameter pile foundations and also to support the proposed basement excavation. Ground water table was encountered at about 6m below the existing ground level (EGL). In order to support heavy structural loads, large diameter bored cast-in-situ piles were chosen and installed. Further, complete retention system was economically designed and built, which includes installation of Contiguous Bored Piles (CBP) in combination of vertical grout columns behind CBP wall to seal the gap between the CB Piles, installation of inclined ground anchors, construction of capping beam, stressing and locking of installed ground anchors. A detailed monitoring program was in place and continuous monitoring of wall deflections is being measured at the time of publishing this paper. This paper describes the design and construction aspects adopted for foundation and retention system including the monitoring results during excavation stage of the project.INTRODUCTIONIn general, stage wise open excavation will be opted for basement construction where plenty of space is available. Due to urbanization and restricted space, open excavation became a difficult task nowadays. To overcome this problem, suitable retention system need to be selected to retain the soil mass. Selection of suitable retention system for multi-level basement excavation is a great challenge in geotechnical industry, especially when the proposed site is located within the minimum set back distance from the existing structures. This in turn calls for the advanced and innovative methods of retention system.Several earth retention systems such as Diaphragm Walls, Secant Pile Walls, CBP system, Soldier Pile Walls, Sheet Piles, Deep Soil Mixing (block walls) etc. with or without inclined ground anchors are being practiced worldwide. Considering the advantages and disadvantages of the available retention systems in practice locally and keeping in view of present site conditions, the developer has chosen CBP system with inclined ground anchors so that all foundation related works of the project will be handled in a single package. The main advantage of such packaged solution will ease the coordination between design consultants and foundation contractor resulting in faster construction of foundation works which in turn reflect savings in time and cost."

Jan 1, 2015

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Mass stabilization, Cut-Mix-Injection (FMI), and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By Ryan Higbie, King Chin, Matthew Anderson, Mike Huggins, Rian Johnson, Dave Sinsheimer

"The Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of New Orleans’ extensive hurricane risk-reduction system constructed following Hurricane Katrina. The project consists of three discrete pump stations and flood gates on the shore of Lake Pontchartrain which provide a storm surge barrier and pump rainwater from the City of New Orleans’ primary drainage canals. The depth of the pump station structures ranged between 39 and 45 feet below sea-level. USACE developed the PCCP project for design-build delivery; granting the project team latitude to develop innovative, cost effective solutions for the project. The use of OPEN CELLTM cofferdams to construct the pump station structures was one such innovation. OPEN CELL structures utilize the strength of the retained soil to anchor cellular sheet pile face arcs; allowing a free-field of construction within the cofferdam. This cofferdam design did not require ground improvement or dewatering around the perimeter of the cofferdam. The free-field cofferdams streamlined construction and large equipment installation within the structures with no encumbrance from internal bracing. Meticulous force-based design, soil-structure numerical modeling, and physical testing were all techniques used to present and gain USACE acceptance of the design on this vital element of the work.PROJECT DESCRIPTIONThe Permanent Canal Closures and Pumps (PCCP) project is the capstone piece of the City of New Orleans’ extensive hurricane risk-reductions system constructed following Hurricane Katrina in 2005. The project encompasses three separate pump stations and floodgate structures located at the mouths of three outfall canals (17th Street, Orleans, and London) on the south shore of Lake Pontchartrain. These three canals, running from the south to north, act as the primary conduits for discharging water from the New Orleans area. Prior to Hurricane Katrina, these canals were operated with pump stations two to three miles upstream of the mouths at Lake Pontchartrain. This left long stretches of levee on each side of the canals exposed to storm surges entering from the lake. Three levee failures occurred along these canals during Katrina; two at London Canal and one at 17th Street Canal. The failures resulted in major flooding of the surrounding neighborhoods, significant damages, and loss of life.Following initial canal levee repairs after Hurricane Katrina, USACE, in partnership with the Louisiana Coastal Protection and Restoration Authority (CPRA), took action to move the line of flood protection to the mouths of these three canals at the edge of the lake. By cutting off the storm surges from Lake Pontchartrain at the entrance to the canal, over ten miles of canal levee would no longer be exposed to storm surge water elevations, significantly decreasing the risk of failure."

Jan 1, 2017

By Shaw-Shong Liew

This paper presents the processes of investigation, analysis, design, construction and monitoring of soil nail stabilisation work to facilitate a 14.5 m deep excavation at an uncontrolled fill ground. An extensive instrumentation programme had been implemented to monitor the performance of the stabilisation solution, to provide validation for the designed nail resistance and groundwater variation. From the monitoring results, it was proved that the soil nail stabilisation technique is effective for loose saturated fill provided that substantial care is taken during implementation. Construction difficulties, solutions to overcome the problems and lessons learned will be discussed in the paper.

Jan 1, 2006