Search Documents

By G. Morin, F. Chiesa, B. Duchesne

The Quality index is a useful tool allowing to assess the metallurgical quality of aluminium AlSiMg foundry alloys (A356/357). Its value is calculated from the ultimate tensile strength and elongation; it increases with the metallurgical quality of the casting, i.e. with finer dendrites, lower microporosity and inclusion count and lower iron content. This Quality index does not depend on the degree of temper applied during the heat treatment (aging time and temperature). After defining the Quality index, it will be explained how it can be predicted from the knowledge of the local solidification conditions obtained from modelling. The paper will then present four case studies of castings for which the prediction of the Quality index by modelling was made. These case studies from different authors will involve the three most common casting processes used for producing high integrity aluminium castings, namely: sand casting, permanent mould casting and investment casting (lost wax). In all cases, the accuracy of the prediction will be assessed by comparing the predicted Quality index distributions to the experimental values based on the published measured values of the local tensile properties.

Jan 1, 2006

By F. E. Senftle

Introduction The usual laboratory methods of uranium analysis are either tedious, time-consuming chemical procedures or elaborate physical methods requiring sensitive equipment. There is thus an urgent need for a method of estimating the uranium content of ore samples by approximate analysis in the field. When a new property is being developed, it is desirable to know, with the least possible delay, the uranium content of channel samples in order to guide the diamond drilling and digging operations. Prospectors, too, require approximate analyses of their hand specimens to evaluate their discoveries. To satisfy the demand for these types of analyses, several field procedures have been tried. Two general plans can be followed. One is fast but will yield only a rough estimate. The other is slightly longer but, if done carefully, will give an assay probably within 10 per cent of the true value. For field operation it is necessary to strip the more accurate laboratory methods of analysis of all refinements because of the limited equipment and skilled techniques at hand. Most of the corrections normally applied, with the exception of that for equilibrium, will not alter the gross analysis to any appreciable extent. When uranium atoms in pitchblende disintegrate, they break down into other radioactive elements, and eventually the number of elements being formed is equal to the number breaking down. The ore is then said to be in equilibrium. Certain geological processes, however, such as leaching, may selectively remove some of these elements and hence reduce the radioactivity of the ore sample. The ore is then said to be out of equilibrium. The field analysis may then be in error by as much as 50 per cent since the apparatus is calibrated with standards that are in equilibrium. However, such a large error due to loss of equilibrium is the exception, and in most cases uncorrected field types of analyr.is are justified.

Jan 1, 1949

By H. Memarian

In the last few decades, many developing countries have tried to expand and improve upon higher education, which is acknowledged to be the leading factor for development. In this respect, develiping countries have significantly increased the number of tertiary institutions and their students. These rapid expansions, along with all the benefits, have drawbacks as well. An example is the status of mining engineering education in Iran. Presently, the number of active mining engineering departments in Iran (27) is more than the sum of similar departments in Canada, Australia, the United Kingdom, and South Africa (23 altogether). Also, the number of annual mining graduates in Iran (645) is more than the cumulative graduates of the United States, Canada, the United Kingdom, and Australia (613). The expansion of mining engineering education in Iran has coincided with the closing or merging of similar mining departments, as well as a decline in the number of interested students in the industrialized world. The present study shows that the need for development and the excessive number of high school graduates, resulting from high population growth in the early 1980s, are the two primary factors influencing the significant expansion of mining engineering education in Iran.

Jan 1, 2007

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By Deni Pageau, Deni Caron

"This paper describes the operations of the open pit and emphasizes particular aspects of Les Mines Selbaie. The open pit as well as its related services were incorporated into a complex which includes an underground mine and a concentrator. The equipment was chosen with the objective of auto-sufficiency during each phase of mining. The paper outlines the organization and the methods used in each step of mining, notably: drilling, blasting, loading, transporting and crushing. The responsibilities of the Engineering Department are also outlined from the conception of the open pit to the latest follow-up methods. A short resume of the results which have been obtained as well as suggestions for improvement are provided.Layout in Consideration of Main SiteThe A-I zone deposit is located I km from 8 zone. Open pit mining of A-I zone required the regrouping of different services to those already existing.I. The crusher was placed in an area close to the concentrator in order to minimize the length of the conveyors and to provide space for the crushed ore reserves (50000 tonnes).2. The location of the service building (warehouses, mine offices, maintenance, engineering and geology) raised a few problems. Because of the multiple services provided therein , it was impossible to fulfill all the requirements, and the garage in itself is located a fair distance from the pit. Added to this inconvenience is the fact that heavy equipment regularly travels throughout the main yard.3. The storage of explosive magazines has been changed to obtain more surface space and meet government regulations.4. A space has been provided for minor repairs in the garage used during exploration. A trailer was installed next to the garage to provide a lunch room for the employees working at the open pit."

Jan 1, 1990

By Edward R. Rose

This paper summarizes and emphasizes the potential importance of Canadian rare-earth occurrences, and recommends that efforts to locate and evaluate rare-earth deposits should be increased. Increasing world markets, depending on intensive applied research into the numerous unique and remarkable chemical and physical properties of the rare-earth elements (REE), are developing; their properties and uses are becoming better known; methods of separation are much improved. The REE group comprises a Cerium (Light) subgroup of 7 metals and an Yttrium (Heavy) subgroup of 9 metals. REE are trace elements in many rocks and minerals, and major constituents of more than 50 rare-earth minerals, many of which are difficult to detect and identify. They occur preferentially in acidic and alkaline igneous and metamorphic rocks, including carbonatites, as well as in placer deposits, certain uranium deposits, phosphate rocks and others. The main ores now are bastnaesite (in Precambrian carbonatite), monazite and xenotime (in Recent beach sands) as well as uraninite and brannerite (in Huronian quartz-pebble conglomerate) and loperite (perovskite) and apatite (in alkaline complexes). World resources are summarized. Twenty mines in 1973 produced an estimated world total of about 31,000 tons of contained rare-earth oxides (REO), 19,341 tons of which came from one mine at Mountain Pass, California. A selected fifteen, of 315 or more Canadian occurrences, are briefly described and compared, and their relative merits indicated. Their abundance and variety suggest the possibility of finding high-grade deposits in many geological terranes in Canada.

Jan 1, 1979

By N. A. Warner

Virtually zero gas emission smelting is promoted as a means for securing environmental advantages and the general public’s acceptance. Concerns about climate change will increasingly make it more difficult for new primary metals projects to come to fruition unless greenhouse gas emissions are decreased. Assuming a sustainable market for sulphuric acid is not locally available, the next best option is high temperature reaction of strong SO2 with limestone or dolomite. This is followed by CO2 liquefaction and disposal either underground or in the deep ocean. The Voisey’s Bay nickel project is cited as an example where appropriate location of a new smelter close to large dolomite or limestone deposits would lead to a virtually zero gas emission operation. Most of the electrical energy required for producing technically pure oxygen and for liquefying CO2 and transporting it to disposal can be derived from smelting a bulk sulphide concentrate and then reacting SO2 at high temperature. Provided the smelter gases are properly cleaned before sulphur fixation, the sulphated stone should be uncontaminated and environmentally benign and possibly of use in the building and construction industry.

Jan 1, 1999

By G. R. Phare

Explosives formulation is dictated by desired field performance, which in turn is dependent on such physical properties as strength, velocity of detonation, sensitivity, and water resistance. The design of explosives to obtain these properties is discussed with some reference to detonation and rock mechanics theory.

Jan 1, 1958

By M. L. Jeremic

The design of the long-hole sublevel mining method was originally based on the traditional assumption that the principal load was due to the weight of the overlying rock, and that the horizontal stresses are equal to one-third of the vertical stress. However, as mining progressed, the virgin lateral stress was found to be equal to or greater than the vertical stress. The virgin stress in the rock mass is not uniform throughout the folded orebody and adjacent strata. From detailed investigations, three basic patterns of virgin stress in ore panels have been inferred: uniform, bent and twisted. Stresses induced by stoping are up to three times greater than original stresses in the rock mass; they cause heavy ground conditions and make extraction of ore difficult. In the last ten years, the original mining system has been modified several times in order to destress the ground and improve the extraction of ore.

Jan 1, 1978

By C. Kunze

ABSTRACT Although closure sureties cover works that are carried out during the existence of a mining company, certain liabilities are not known when the surety is established and become apparent only in a late stage of the closure phase, or even after the site has been relinquished. This paper supports the concept that these financial risks lend themselves to insurance solutions. Making insurance for unknown liabilities mandatory while defining unambiguous legal conditions could create a viable market for insurance products, provide a sufficient statistical basis for the calculation of premiums, and reduce costs.

Jan 1, 2013

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By J. G. Cullain

Inco Limited is an integrated mining, smelting, refining and manufacturing company with operations located worldwide. The Ontario Division operations consist of 13 mines and 10 processing facilities located in Sudbury, Port Colborne and Shebandowan. The scope of our utilization of energy in the Ontario Division in 1976 included in excess of 2.2 billion kilowatt hours of electric power, 12 billion cubic feet of natural gas, 60 million Imperial gallons of residual oil and smaller quantities of other fuels. In addition to the primary energy consumption, waste-heat energy is recovered in various operations throughout the Division, thereby reducing our primary energy requirements. Total expenditures for primary energy alone in 1976 exceeded 60 million dollars. Energy management studies were initiated by Inco's Utilities Department in late 1972, and resulted initially in a program of electric power cost reduction. This program produced significant results by improving the use of the water available for our hydraulic generation facilities and by a comprehensive peak reduction program. Our experience showed that a program of peak power control creates an awareness of both peak and energy costs, and thereby encourages a general reduction in the electric energy consumption as well as lowering the peak demand. Energy management is a continuing program at Inco and, recently, a formal energy management policy and program was instituted. Energy management committees were formed in each plant or mine area to identify the major areas for energy; consumption, thereby isolating areas with large potential energy losses, and determining immediate action which will improve the energy efficiency or reduce the energy waste within their respective areas. A decentralized program with good cross-communication between all committees was felt to be the best method of providing an on-going effective energy management program. In the future, the projections of dwindling fossil-fuel supplies in Canada and the resultant spiralling energy costs will further emphasize the need of sound energy management practices for all Canadian industry.

Jan 1, 1977

By N. M. Stubina, P. J. Lind

Barrick Gold is in the process of building several new mines and implementing new processes at existing mines for which metallurgical technology is of key importance. The roles of the company's Strategic Technology Solutions team and the Barrick Technology Centre are discussed within the context of their responsibilities within Barrick's Operations Support group. The paper will present an overview of the development of the technology centre from the former Placer Dome Research Centre to its current form supporting strategic technology, capital projects, and operating sites. Novel approaches to research and development will be presented as well as an overview of some of the technologies developed from bench-scale to pilot-scale, and beyond.

Jan 1, 2011

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996

By G. J. Birnie

Introduction The preparation of the following paper has been undertaken in the belief that a description of the development methods and equipment used at Lake Shore, at the present time, will prove of general ? interest. Working depths of nearly a mile and a half in shaft sinking and of more than one mile for stoping operations have imposed problems not encountered at shallower horizons. Among the problems contributing to the difficulty of mining at extreme depths might be mentioned: Rock pressures Ventilation Hoisting Shorter work period at the face Geological considerations In the main, the effects of these factors add to the difficulty of mining at depth, but it is not entirely true to say that each must necessarily become more pronounced as mining operations proceed to greater depths. Corrective measures may, in some cases, retard the effect and in others may even relieve some of the difficulty. It is proposed here to discuss these features in the light of the experience at Lake Shore, and to present, in some detail, the current practice in shaft sinking and in driving ore and waste passes, raises, drifts and cross-cuts.

Jan 1, 1950

By A. Poitras

The Cummings Complex consists of three superposed sills, exhibiting a differentiation pattern: the lowest sill being the most basic and the highest sill, the most acid. Each sill is also characterized by an internal petrographic and geochemical variation which is evidence of differentiation due to fractional crystallization. The REE concentrations in the different units of the complex indicates that the three sills are comagmatic. The interpretation of these results permits the formulation of an emplacement model not previously proposed for this complex.

Jan 1, 1984

By A. M. Glendinning

"IntroductionLocationTHE PROPERTY of Aunor Gold Mines, Limited is in Deloro township, Ontario, about three miles southeast of the town of Timmins. It consists of a group of eleven claims located between those of Buffalo-Ankerite Gold Mines, Limited, and Delnite Gold Mines, Limited.GeologyThe ore zone at the Aunor mine consists of a narrow band of fine grained pillowed andesite, irregular bands of 'brown to green carbonated andesite, and lenticular bodies of quartz feldspar porphyry. The zone strikes N.80°E., dips 60 North, and has been traced for 5,000 feet across the property. It varies in width from 0 to 250 feet and is bounded on the north and south by masses of dark bluish-grey tale chlorite schist. These schist bands have widths up to 500 feet.The ore occurs in a series of parallel and branching veins confined to the limits of the zone. These veins tend to terminate and die out on the footwall schist contact, striking generally parallel with the ore zone. In wide sections of the zone, 150 to 250 feet, the veins range in width up •to 3.5 feet and may occur in two or three horizons across the width of the zone, each mineable independent of the other. They tend to dip a little flatter than the general dip of the zone. Where the zone is narrow, the veins are so closely spaced and numerous they can be mined together and in some places the complete zone has been mined from schist to schist."

Jan 1, 1953

By Matt Manson

Renard?1-10 kimberlite pipes and ?Lynx-Hibou?kimberlite dyke system within ?Foxtrot?property 50/50 JV with SOQUEM, Stornoway operator 2001: Discovery of the Renard kimberlite pipes 2003: Discovery of the Lynx-Hibou kimberlite dykes 2006-2007: Bulk sample program 2008: First 43-101 Resource and Preliminary Assessment 2009/2010: Updated 43-101 Resource

May 1, 2010

By A. Rodriguez-Prado

"Magnetic fields affect the growth of cultured cells and plants; however, limited information exists about their effects on vegetation performing environmental remediation. Constructed wetland mesocosms treating hexavalent chromium (Cr(VI)) wastewater exposed to low-intensity magnetic fields (60 Hz, 56.5 × 10-6 Tesla) produced 100% more biomass than the unexposed control. Nonetheless, they removed only 43 ± 27% of Cr(VI), compared to 60 ± 21% for the control. A Cr(VI) reduction expression was developed as a function of the magnetic field. The design and operation of constructed wetlands to treat mining wastewater can be corrected for magnetic field effects.RÉSUMÉ Les champs magnétiques affectent la croissance des cellules et des plantes cultivées; toutefois, il existe peu d’information quant à leurs effets sur la végétation utilisée à des fins d’assainissement environnementale. Les mésocosmes des marais artificiels traitant des eaux usées, contenant du chrome hexavalent (Cr(VI)), exposés à des champs magnétiques de faible intensité (60 Hz, 56,5 × 10-6 Tesla) ont produit 100 % plus de biomasse que le contrôle non exposé. Néanmoins, ils n’ont enlevé que 43 ± 27 % du Cr(VI), comparativement à 60 ± 21 % pour le contrôle. Une expression de réduction du Cr(VI) a été développée en tant que fonction du champ magnétique. La conception et l’exploitation de marais artificiels pour traiter les eaux usées des mines peuvent être adaptées pour tenir compte des effets des champs magnétiques."

Jan 1, 2015