Search Documents

By Offler R, Lau J, Lea J. F

The stratiform and vein-type pyritic silver-Iead-zinc-copper sulphide deposits of Sunny Corner, NSW are hosted by acid volcanic and clastic sedimentary rocks of Middle Silurian to Early Devonian age. The rocks have been subjected to low-grade regional metamorphism (prehnite-pumpellyite facies) and three phases of folding and four faulting events are recognised. Pyrite is intensely fractured, indicating brittle deformation. Chalcopyrite and galena exhibit deformation twins and slip planes indicating ductile deformation; sphalerite and chalcopyrite show straight and curved grain boundaries and dihedral angles of 120° as evidence of annealing recryslallisation. Sulphur isotope ratios for 22 samples from five deposits range from 1.7 to 10.7 per mil and average 7.4 per mil. Sulphur isotope data are similar to those from other stratiform sulphide deposits in acid volcanic rocks of Late Silurian age in the eastern Lachlan Fold Belt, especially Woodlawn and Captains Flat and together with other features of the mineralisation, suggest a volcanic exhalative origin for the Sunny Corner deposits.

Jan 1, 1984

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

The Imperial Smelting Process (ISP) for the simultaneous smelting of zinc and lead was developed at Avonmouth from the 1930's with activity intensifying in the late 1940's/early 1950's. Present operations are based around the No.4 furnace which was built in 1967. Development during the 1980's has been driven by the need to sustain operations at low metals prices and has been aimed at reducing manning whilst increasing output. Although hit by several major plant disruptions, progress has been steady, culminating in a ú10 million capital programme in 1988?89 to upgrade the operation. The most important technical developments, reflecting the needs of the 1990's have, in the sintering area, included improvements to feed conditioning and sinter quality, a 20% uprate in production capacity by debottlenecking, and pilot work leading to the installation of a Boliden-Norzink mercury removal plant. In the smelting area the ISP furnace has been rebuilt, with a redesigned bottom section to eliminate earlier operating sensitivities, and to achieve higher blowing capability, and at the zinc refinery the columns have been rearranged for more flexible operation and higher capacity.

Jan 1, 1989

By S W. Houlding

The Certificate in Mining Studies program at the University of British Columbia, Vancouver, Canada is a collaborative initiative between mining schools and industry to provide accessible, cost-effective, accredited continuing education and training, designed to address the future needs of the global mining community. Content is provided by industry specialists and delivered through an integration of online learning, short courses and interactive webcasts. Accreditation is provided by a network of mining schools. In 2011, the program will deliver close to 100 short courses and interactive webcasts and provide 24/7 access to more than 130 online courses in six mining streams, to participants from as far afield as Tanzania, Argentina and Mongolia. The program is proving adaptable to corporate and mine site engineer-in-training and graduate-development programs, as well as providing accessible professional development opportunities for individuals. It also provides opportunities for cross-training from other disciplines and integration with mining school curricula.

Nov 22, 2011

By W Liu, S Gao, D Wei, B Cui, Z Guan, Y Shen

Beneficiation of low-grade fine-grained hematite ores becomes increasingly important due to rapid depletion of high quality iron ore resources. However, fine particles, especially ultra-fine particles, make efficient beneficiation of these ores more difficult. Therefore, methods to reduce the influence of fine particles must be considered to achieve better beneficiation performance. Analysis and systematical beneficiation tests were carried out on an ultra-fine-grained hematite ore slime from washing a fine grained hematite ore. Ore particles were found to be presented in loose soil. While some of the ore particles were agglomerated, they were very fine and contained up to 76.5 per cent -0.023 mm material. In this paper, using a single magnetic separation flow sheet with sodium silicate (SS) as a dispersing agent, a concentrate containing 65.05 per cent Fe was obtained at an iron recovery of 68.58 per cent from the hematite ore slime of 56.65 per cent Fe. The single magnetic separation flow sheet was simple and reliable, the agent SS was effective in dispersing ultra-fine particles. The results are believed to be applicable to similar hematite ores.CITATION:Wei, D, Guan, Z, Gao, S, Liu, W, Shen, Y and Cui, B, 2013. Beneficiation study of an ultra-fine-grained hematite ore slime, in Proceedings Iron Ore 2013 , pp 495-500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Krull, T J. Donohue, D Ilic

"Problematic issues in materials handling applications are often amplified in the iron ore industry due to the relatively high density of the ore as well as the abrasive nature of the product. One of the main issues arising from the handling of iron ore is excessive wear, with two applications typically suffering accelerated wear issues being transfer chutes and conveyor belts. These wear issues are problematic due to additional capital costs, but mainly due to the associated downtimes resulting in the accelerated wear. This study will focus on the modelling of iron ore in practical applications where design work was undertaken in order to reduce the wear rates of different materials handling equipment.CITATION:Donohue, T J, Ilic, D and Krull, T, 2013. Modelling of iron ore in materials handling applications with a focus on wear, in Proceedings Iron Ore 2013, pp 355-362 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E Claridge

There are a number of major infrastructure tunnelling projects currently underway or proposed in New Zealand, including construction of new road and rail facilities and the refurbishment of existing road tunnels. These new projects have triggered a rethink of traditional practices in underground fire and life safety and local regulation.While there is a current surge in activity, tunnels have been a signifi cant part of New Zealand’s transport infrastructure for over a century. Despite this background, the new projects commonly face challenges that are symptoms of a national regulatory environment that has aspects that are inappropriate for underground environments. There are inconsistencies in local regional regulation and an absence of national guidance and standards relating to tunnel design. Historically, New Zealand has looked across the Tasman for guidance. Although recent overseas tunnel designs present learning opportunities, the adoption of international best practice and standards may not necessarily address local expectations or needs.This paper explores a number of specific matters affecting the design of road and rail tunnels in the New Zealand context, namely; the Building Regulations and associated local consenting processes and parties, and the responsibilities and needs of the New Zealand Fire Service.The discussion highlights the importance of a collaborative approach involving the designer, asset owner, regulators, emergency services, and other parties, and ensuring up-front clarity in design responsibility and ownership of residual risk.

Mar 8, 2011

By Vynne J. F

Drill monitors for blasthole and exploration drills have been available to the mining industry since the 1970s. The early monitors were pen strip chart recorders which were developed for the oil drilling industry and adapted to mining. They recorded drilling parameters such as depth, pull-down pressure, torque, RPM, and bailing air pressure. While these recorders could generate a large volume of paper, the amount of useful data was minimal. The data was not summarised and required an engineer to interrupt the chart traces. Being a mechanical recorder, the devices were also susceptible to frequent failures.

Jan 1, 1993

By Mankosa MJ, Yoon R-H

A reliable scale-up procedure for column flotation must address three important areas of column design, ie column geometry, sparging system and wash water distribution network. The column geometry is dictated by the maximum froth carrying capacity (which determines column diameter) and the bubble-particle attachment rate and particle retention time (which determines column length). The most important factor in the scale-up of an air sparging system is the ability to produce small bubbles in both laboratory and full-scale columns. Other factors, such as energy consumption and maintenance requirements, should also be considered in the scale-up of bubble generators. It is also important to design a wash water distribution system that can properly control the froth stability and maximise the column throughput. Based on these criteria, a successful scale-up example is given.

Jan 1, 1993

By Stump NW

Until a year ago all isotope on-stream analysis utilised flow cells similar to those designed for conventional X-ray on-stream analysis. These systems incorporated a fairly complex sampling system necessary to present a representa- tive air-free sample of the main process to the flow cell. Maintenance costs and capital costs associated with flow cells and sampling systems have been generally high. Costs can be greatly reduced and reliability greatly increased, by using isotopes incorporated in immersible on-stream analysis probes which actually dip into the main process stream eliminating the need for sampling. A bonus of other advantages associated with immersible probes includes temperature stability and ease of calibration. This paper discusses details and results of the probe systems, justifica- tion for installing on-stream analysis, comparison of conventional X-ray and isotope techniques, and a brief survey of methods of analysis using radio- isotopes in on-stream elemental determinations.

Jan 1, 1971

By Hagan T. N

Quite apart from economic considerations, the following performance parameters must be considered when selecting an explosive for a particular blasting operation. 1. total energy yield/kg, and more particularly, strain energy/kg and bubble energy/kg of charge 2. charge weight/m of blasthole 3. sensitivity of the charge 4. water resistance of the charge The effective division of an explosive's total energy into strain energy (SE) and bubble energy (BE) is explained as is the influence of each energy component on blast results. Because some rocks require a high strain energy for effective breakage, while others are most satisfactorily fragmented by bubble energy, values of SE and BE are more meaningful than those of total energy. Unfortunately, our extensive knowledge of the effects of certain variables on total energy has not yet been completely supplanted by the influence of these variables on SE and BE values. Relative SE/kg and BE/kg values are presented for a range of explosives. The 'charge density of ammonium nitrate/ fuel oil (ANFO)-type explosives is essentially constant throughout the length of the charge; because of their compressibility, slurry

Jan 1, 1974

By James CH

For drainage sediment to be used as a successful sampling medium in reconnaissance geochemical surveys, the length of any dispersion train from a typical target must be great enough for it to be detected by a widely spaced sampling pattern, and must also be homogeneous enough to avoid it being missed by the unfortunate selection of a random low value sample. Elements which occur in stream sediments in the form of discrete heavy minerals present two special problems in this regard. Since the element is concentrated into a few particles, the medium is extremely heterogeneous, which makes representative sampling impossible unless very large samples are taken, while the high specific gravity of such grains leads to their being concentrated in traps along the stream bed. Several ways of overcoming these difficulties have been suggested. Among these the "schlich" test, in which heavy material obtained by panning is taken for analysis is among the most popular. However, the results of the present study indicate that while this method improves the nature of the patterns obtained, they are still far from satisfactory. Alternative methods of sample preparation, including the taking of light material for analysis, appear to provide better answers to the problem. In the area studied this approach eliminated most of the "noise" associated with the data obtained by other methods, as well as giving an extended dispersion pattern.

Jan 1, 1986

A model has been developed for the per iodical maintenance of bins used for hydraulic hoisting in mining of steeply inclining coal seams. This model gives a control plan for hoisting, bin switching and bin maintenance on a regular schedule.

Jan 1, 1977

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976

By Aziz N

The objective of the paper is to develop an understanding of the influence of caving on powered support rating by examining the geology and support performance at two sites which represent the current extremes in support rating, ie 6/240 Ton supports operating in the Hirst Seam at Solsgirth Colliery, Scotland, and 4/900 Tonne supports operating in the Bulli Seam, West Cliff Colliery, Australia. A conceptual model is introduced which considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata. Different caving mechanisms are identified for the strata of the Hirst and Bulli Seams, ihese mechanisms being related to rock properties, ie to the palaeogeography and depositional conditions at each site, producing caved wastes with different yield characteristics. The results obtained for convergence and support reaction during production cycles at both sites are analysed to show the manner in which support reaction is developed, indicating the importance of high setting load densities in the Bulli Seam. Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations, ie the powered support and the caved waste immediately behind the powered support, is used to further demonstrate the influence of caving mechanisms on support rating.

Jan 1, 1986

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operations at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry.Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle ize distributions and brightness values have been prepared.Extensive drilling and bulk sampling of the deposit over eight years has shown that the orebody is large and of a high grade suitable for the production of premium quality coating kaolins.The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW).The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment, the nature of the production process and details the project management procedure used for the design, construction and commissioning of the plant. Three areas of significant interest, the gas turbine fired pray dryer, the moving bridge shiploader and the use of aerobelt conveyors on the project are detailed.

Jan 1, 1988

By Needham RS

Hydrothermal mineral deposits are the dominant mineral deposit type in the Cullen Mineral Field, and have been important sources of tin, tungsten gold, silver-lead, zinc and copper. The deposits are mostly in north to northwest-trend- ing shear zones, and are confined to Early Proterozoic contact metamorphosed metasediments or synorogenic to postorogenic granitoids. The distribution of the vein-type deposits with- in the contact aureole defines a district-scale metal zonation of uranium closest to granitoid, through tungsten, copper, tin, silver-lead to gold with increasing distance from granitoid contacts. This zonation probably reflects de- creasing temperatures within the contact aureole during granitoid emplacement, and at the time of generation of a variety of metal-bearing fluids. A magmatic source for some of the metals is indicated by the positive spatial relationship between uranium, tungsten, copper and silver-lead deposits and granitoids abundant in those metals. There is little evidence for any such relation- ship for tin and gold deposits, except for an association of some tin deposits with tin-enriched mafic rocks. Most of the granitoids with anomalous metal values are late stage highly fractionated leuco- granitic phases forming younger plutons peripheral to the main body of the Cullen Batholith, They probably form cusps connected to the main body at shallow depths.

Jan 1, 1984

Conventional narrow vein mining, utilising hand held methods, is expensive and requires specialised miners who are becoming a rarity. Hand held mining techniques (shrinkage stoping, leading stoping and cut and fill) have the advantage that they can be selective. The methods allow continued sampling of the face, control of hanging wall conditions and are adaptable to changes in strike and dip. On the other hand, more productive longhole stoping methods can allow excessive dilution due to drill hole deviations and changes in orebody dip and can be subject to unexpected hanging wall or footwall failures. Development of small scale equipment (as narrow as 0.8m wide) used for drilling or bogging very smallaccess drives has been ongoing over the past decade. In this paper, types of equipment are examined and compared, particularly with respect to their produc- tivity, size, and working environment. The introduction of electric hydraulic equipment has provided a better working environment with reduced noise, exhaust fumes and heat. The concept of the "hydraulic cherry picker" may have application in mining steeply dipping orebodies. The system requires orebodies to be reasonably consistent in dip over 15 metre sub-level intervals. The system involves the basic concept and skills of machine and airleg mining, combined with the safety and productivity of a mechanized work platform. The platform or basket is stabilized between the hanging wall and foot- wall by hydraulic rams and is extended by a tilting hydraulic boom mounted to a small prime mover or trailer. Design concepts (including remote controlled charging of explosives, adaptation to the boom for rock cutting and the overall electric hydraulic mining concept) are put forward in the paper as a view as to how narrow vein mines will be mined in the future.

Jan 1, 1987