Search Documents

By A. J. Buchan

The wear of steel pipelines used for the transportation of backfill slurries is frequently regarded as an erosion problem only. An investigation was undertaken of the likely contribution to the total 'wear rate' made by corrosion. Use was made of a pipe flow loop with catholically protected specimens and corrosion inhibitors. Laboratory electrochemical tests utilizing a rotating-cylinder electrode were also conducted. The slurries used were classified tailings from two mines at a relative density of 1,7. The velocities were between 2 and 4,9 m/s. Substantial decreases in the wear rate of up to 80 per cent for one slurry and up to 67 per cent for the other were obtained with the use of corrosion control, showing that corrosion and, more importantly, interaction between erosion and corrosion, contribute a significant portion of the overall wear in steel pipelines

Jan 1, 1994

By Z. Khan

Iron, in the form of steel and stainless steel, is the most commonly used metal in the world. Plain steels corrode and oxidize easily, while stainless steels exhibit improved corrosion and oxidation resistance. It has been found that rare earth metal (REM) additions, such as cerium and erbium, result in the improvement of the abovementioned properties in iron-containing compounds. Gadolinium is a REM, however, there is very little information available on the influence of gadolinium on the microstructure and mechanical properties of iron-containing compounds. Thus, the purpose of this research project was to determine the influence of gadolinium additions on the microstructure and mechanical properties of mild steel and 316 stainless steel. Ten alloys were produced for the purposes of this research. Five of the alloys had a base composition of mild steel while the remaining five had base composition of 316 stainless steel. The alloys for each of the base composition contained gadolinium additions of 0.1, 0.5, 1.2, and 5 weight per cent. The as-cast and the cold-rolled alloys were analysed. The alloys responded well to the cold-rolling with the exception of the 5 weight per cent gadolinium mild steel and stainless steel alloys. These alloys were extremely brittle and underwent a significant amount of cracking during the cold rolling process. A microstructural analysis of the alloys was conducted using a light optical microscope, while the chemical analysis of the alloys was conducted using energy dispersive x-ray spectroscopy (EDS). The resulting microstructures and EDS analyses revealed that the gadolinium displayed minimal solubility in the ferrite matrix of the mild steel alloys and minimal solubility in the austenite matrix of the stainless steel alloys. Instead the gadolinium formed as an interdendritic secondary phase in both alloys. EDS analysis revealed that the secondary phase in both alloys was gadolinium-rich. Vickers microhardness tests conducted on both alloys revealed that the alloys were composite-like, with a hard, brittle gadolinium-containing compound dispersed throughout a softer, more ductile matrix. The corrosion resistance of the alloys was determined through potentiodynamic anodic polarization tests. Two solutions were used for the corrosion rate tests: a 0.5 weight per cent NaC1 solution and a 0.5 M H2SO4 solution. The results from the mild steel alloys revealed that in both the solutions, the corrosion potentials and the corrosion resistance of the alloys increased with increasing gadolinium concentration up to 1 weight per cent. The corrosion rate test results from the stainless steel alloys revealed that the passivation current density and corrosion resistance of the alloys increased with increasing gadolinium concentration in both solutions. The oxidation resistances of the mild steel and stainless steel alloys were determined through the use of a Netzstch Simultaneous Thermal Analyser. For both the mild steel and the stainless steel alloys, it was found that the oxidation resistance of the alloys increased as the concentration of gadolinium increased when compared to the as-received mild steel and stainless steel samples. This could be due to a strongly adhering gadolinium oxide scale that formed on the surface of the alloys and resulted in the protection of the mild steel and the stainless steel.

Jan 1, 2012

By А. А. Vasiliev, Y. G. Seredkin, А. V. Aksenov, А. Y. Senchenko

Refractory gold-containing concentrates usually contain gold enclosed in sulphides as well as in rock-forming minerals. Another difficulty is that gold often occurs as very fine inclusions of several micrometres, and even smaller than 1 micrometre, or can be part of the mineral composition at the structure level. Processing of such concentrates is a challenge. Ultrafine grinding and further oxidation are applied for gold liberation. The paper deals with the results from the study of gold deportment using Qemscan, and atmospheric oxidation testwork involving Albion Process™ on a gold-containing concentrate with a high content of refractory gold in sulphides and gangue minerals. Albion process testing was performed at Institute TOMS with the participation of Glencore Technology Pty Ltd (Australia). Additionally, conventional cyanidation testwork was carried out for the concentrate processing. As an alternative technology of gold liberation, oxidising roasting with arsenic stabilisation was used. The results from the study make it possible to assess the efficiency of the above-mentioned methods of gold liberation, and applicability of Albion technology to recover gold from the refractory concentrate. Key words: Gold, refractory concentrate, Albion Process, atmospheric oxidation, oxidising roasting, leaching

Jan 1, 2020

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By F. S. Beretta

Mineral processing efficiency depends on various factors and among them includes head grade fluctuations feeding the processing plant. Head grades can fluctuate beyond an admissible range, implying in recovery decrease for the mineral of interest. Grades feeding the processing plant depend on the geological domain which is being mined and on the mining schedule. Therefore, it is necessary to keep grade variability controlled. Blending piles are an efficient alternative to reduce grade fluctuations. The main factors influencing blending efficiency are the pile size or its mass and the number of layers used to pile up. Large piles are more efficient to reduce variability, however, there are economical and operational limits associated with them. This study investigates a methodology to analyse the ideal pile size to reach an acceptable variability given the in situ grade fluctuations. Geostatistical simulations provide the means to assess grade variability using an optimized mining schedule. These block grades are used to simulate any given pile throughout the mine`s life. The methodology was illustrated using a case study to control coal ash content at a mine supplying ROM coal to a power plant. Keywords: homogenization, piles, geostatistical simulation.

Jan 1, 2009

By A. Karadogan

Decision making can be defined as the selection process of the best routes from the alternatives in order to achieve a goal, and mostly involves uncertainty. Additionally, mostly qualitative variables (weak rock, massive ore deposit, etc.) are in question. Mine planning engineers often use their intuition and experience indecision making. As fuzzy set theory has been used since 1970, these uncertainties are easily evaluated in the decision-making process. Real world study is decision making under vague constraints of different importance, involving uncertain data (qualitative variables), where compromises between antagonistic criteria are allowed. This paper presents a new approach in the selection of an underground mining method based on fuzzy set theory for the Ciftalan Lignite Site located close to Istanbul in Turkey. The physical parameters such as geology and the geotechnical properties of ore, hanging and foot wall, economic effects, environmental effects, are established with field and laboratory tests together with the determination of other qualitative variables. Meanwhile, some qualitative variables dealing with the matter was described according to the view of a number of experts. Then fuzzy set theory is applied to these parameters, considering the available underground methods in order to choose the proper method. At the end of the evaluations, the room and pillar method with filling was determined as the most suitable method for the test site. Keywords: Decision making, fuzzy set theory, underground, mining, method selection

Jan 1, 2008

By B. H. Sandelowsky

Prehistoric metal-working in South West Africa by B. H. SANDELOWSKY*, Ph.D. (Visitor) This paper describes a three-hundred year old metal-working site at Rehoboth, and makes a plea for information on such sites elsewhere in South West Africa so that they can be investigated. The technique of ore smelting that was used at Rehoboth appears to be different from that practised elsewhere by Bantu peoples before the modern era.

Jan 5, 1974

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By L. H. Lindstad

The paper reviews the tapping process and the major wear mechanisms on the tap-hole, including wear from tapping tools. Measured temperatures in different tap-holes are related to choice of binder and material for repair pastes. The strength and disadvantage of carbon and silicon carbide materials are compared. Normal daily and weekly maintenance of tapholes is described, together with the major repairs that are done during longer furnace shutdowns. The objective is to show that the type of repair and repair material needs to be adapted to each individual furnace.

Jan 1, 2014

By A. Sampson-Forsythe, P. Morissette, A. R. Punkkinen, D. R. Chinnasane

"The performance of ground support systems under dynamic loading is typically assessed in a qualitative and subjective manner. As a result, it is difficult to develop an explicit knowledge on the mechanisms of action and interaction of support elements subjected to rockbursts. This paper examines rockbursts that have occurred at Creighton, Copper Cliff, and Coleman mines since 2000, 2004, and 2006, respectively. The mines are located in the Sudbury Basin, in Ontario, Canada. The majority of pertinent information was obtained through on-site field assessments, seismic system records, and numerical elastic stress modelling. Passive monitoring is used to link the evolution of the frequency and severity of rockbursts to the evolution of mining and support practice at the three mine sites. Based on the collected data, ground support elements that enhanced the capacity of support systems to withstand dynamic loads are identified. IntroductionThe selection of appropriate mining methods, extraction sequences, rock mass de-stressing techniques, and ground support systems is of great importance in mitigating the level of rockburst-related risk. In burst-prone conditions, the design of support systems should account for the anticipated dynamic load demand and the capacity of the available support options. Furthermore, an economical design should, implicitly or explicitly, take into consideration the consequences of a rockburst and its impact on worker safety and mine productivity. Stacey (2012) has argued that we have a limited understanding of the mechanisms of rock mass behaviour in seismic conditions. This is compounded by a ‘lack of understanding of the mechanisms of action and interaction of support elements under dynamic loads’ (Stacey, 2012). Consequently, the design of support systems required to manage dynamic loads is usually based on experience. The assessment of the dynamic performance of ground support systems is typically subjected to qualitative (and sometimes subjective) interpretations from ground control personnel."

Jan 1, 2017

By D. Kok

A challenge in mine planning is the optimal allocation of resources to the appropriate workplaces within the shift cycle (labour, equipment type, and other resources) in order to carry out the shift cycle activities, achieve planned production targets, and ultimately maximize production within all infrastructure constraints. Generally, detailed mine planning is done on a monthly basis at a workplace level in order to determine the production targets. The production supervisor, mine overseer, or equivalent production manager must then make the appropriate resource allocation trade-off decisions on a daily basis per shift to try and deliver to the plan and required production target. Due to the complexity and number of permutations of possible resource allocation decisions, it is impossible for a human brain to make the appropriate and optimal allocation decisions that will result in achieving the maximum or target production. These allocation decision permutations must deal with the current status of workplaces (availability, position in the cycle etc.), the status of equipment availability (available, planned maintenance, or breakdown etc.), distance between the workplaces (traveling time of equipment between workplaces, etc.) and equipment type required for that shift cycle activity. All these factors need to be taken into account in resource allocation to plan for the shift, and even during the shift if a major piece of equipment becomes unavailable or a workplace activity is not progressing as planned. This paper is a case study on how an optimization algorithm can be used to create a production planning system for optimization of resource allocation in a mechanized underground platinum operation. A business case for optimal allocation of resources is demonstrated and compared to the current manual planned allocation.

Jan 1, 2012

By X. Ndlovu

Underground observations in a coal mine have indicated failure oft he immediate roof above the bords. Careful observations and photographic recording of occurrences of these roof failures, termed ?roof guttering?, have been made. The occurrence of guttering results directly in roof instability, and indirectly, due to the interaction of the guttering with natural planes of weaknesses in the immediate roof rock. In this paper, relevant observations of roof guttering, possible mechanisms of formation of roof gutters, laboratory testing for determination of material strength and deformation properties, and numerical analyses to explain underground observations are described. Mapping of roof failures showed that these took place mainly towards the centre of the roadways. Roof guttering was observed often to occur violently and with little warning. Occurrence of roof guttering has a negative impact on production?some panels are abandoned, production times are increased and safety of workers is compromised. The numerical stress analyses showed that, although none of the constitutive behaviour criteria used predicted the observed underground failures correctly, the extension strain criterion gave the best agreement.

Jan 1, 2007

By S. Blancher, A. Perroton, H Smith, T. Nzima, T. Wallmach, V. Dieudonné

Chromite beneficiation is generally performed by crushing and density separation using spirals. At the Dwarsrivier Chrome mine spiral efficiencies seam to vary, the reason for which is not evident. This sometimes results in the production of low-grade products, which are sold at relatively low prices. This paper represents a Qemscan® study that investigated mineralogical reasons for these variations. Variations in liberation of chromite particles as well as variations in chromite compositions were investigated. The results showed that the so-called low grade chromite product can be improved to become a high grade chromite product by means of a refinement in mineral processing. A detailed Qemscan® database (SIP file) was developed to account for variations in chromite chemistries. It can be shown that chemical variations with respect to Cr, Al, Mg and Fe in chromite particles reporting to the scavenger tails are larger than in the high grade product. A combination of these chemical variations together with a decrease in liberation of chromite particles in the scavenger tails can potentially help to recover more chromite particles from this specific process stream.

Sep 1, 2021

By N. D. Fernandes

Labour-intensive narrow reef stoping, as traditionally practised in South African gold and platinum mines, is almost unique in the modern first-world mechanized mining environment. Shortcomings of the system include the ever increasing cost of labour, a cap on achievable productivity and a poor safety record, particularly in the field of rock-related accidents. In the absence of sustainable alternative technologies, the South African mining industry has spent millions of rands improving the present system, focusing on improving workplace safety. This paper details the changes to stope support at Impala Platinum?s Rustenburg operations, and the impact on rock-related safety performance. Keywords Stope panel support, narrow reef stoping, improving workplace safety.

Jan 1, 2011

By P H. Ferreira

The mechanisation of mine development is becoming increasingly important in our South African and Southern African mines with increased emphasis on safe and efficient mining. Raise, blind and shaft boring offer mechanised solutions for excavations such as:- [reef raises stope boxholes and shaft ore passes ventilation passes and shafts chairlifts large vertical hoisting shafts (in excess of 1200 metres in depth) angled hoisting shafts (from small to large diameter bored holes)] These techniques will be discussed with reference to relevant applications and the author?s comparison between conventional drill and blast techniques.

Jan 1, 2005

By J. D. Steenkamp

In 2002 the commissioning of an ilmenite smelter on the North Coast of South Africa was extended by three months due to the failure and subsequent replacement of the magnesia-based refractory lining. The lining failed due to the hydration of magnesia caused by an unexpected source of water. The incident resulted in significant financial losses and a prolonged insurance claim which was settled in 2009. As magnesia-based refractories are used extensively in both ferrous and non-ferrous applications, the authors of the paper want to share the experience gained from this incident with others. The paper reviews the literature available on furnace start-up practices and explains the hydration of magnesia using available sources. The incident is studied in more detail, both technically and economically, and the costs incurred are quantified in terms of the cost of the original lining. The paper concludes with lessons learned and recommendations made for future work. The intention of the paper is to stimulate open debate regarding best practices in preheating of furnaces lined primarily with magnesia. Keywords Commissioning, hydration, start-up, magnesia.

Jan 1, 2011

By K. Arnold

AngloGold Ashanti has been proactive in the field of energy management for many years. AngloGold Ashanti is a signatory to South Africa?s National Energy Accord of 2005 calling for a15% reduction in energy consumption by 2015 for the mining sector. This target also supported our internal targets that were already set. AngloGold Ashanti?s seven South African mines consume on average 440 MW. Due to the dynamics of gold mines, and the large numbers of relatively small energy efficiency initiatives and awareness campaigns made measurement and verification of energy efficiency very difficult at a macro level since some initiatives could get lost in the fluctuating load profile. This paper will discuss the methodology and process followed to quantify the impacts of the combined energy efficiency initiatives at macro level. It will quantify the energy efficiency impacts in megawatt-hours (MWh), financial, and equivalent carbon emissions (CO2e) reduction with reference to our baseline year, 2004, for the Vaal River and West Wits mine clusters.

Jan 1, 2009

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the Fundamental Sampling Error (FSE)–, Duplicate Sampling Analysis (DSA) and Segregation Free Analysis (SFA)–, are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody was calibrated using the DSA and SFA methods and the results compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to the power of 3. A later modification of Gy’s formula raises dN to the power (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of in the range 0.97 to 1.30. The average value for is shown to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry-preferred 1.5. It is suggested that for low-grade gold-bearing ores the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the FSE greatly simplifies the characterization of gold ores, now requiring only the calibration of K for a given mass and established fragment size. The implications of the simplified equation for the heterogeneity test are that, provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.

Jan 1, 2017

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012