Search Documents

A maximum acceptable level of 2 mg/m3 of respirable coal mine dust in active mine workings was established, effective January 1, 1973, under the Federal Coal Mine Health and Safety Act of 1969. It is generally agreed that, as a result, coal mines in the United States are significantly less dusty than they were a decade ago. For example, operators of underground mining machines were exposed to between 3.9 and 6.5 mg/m3 of respirable coal mine dust during 1968-69; now they are exposed to between 1.3 and 1.8 mg/m3. Also, the incidence of underground sections cited for exceeding acceptable levels of respirable coal mine dust decreased during 1976-78, and the vast majority of all working sections are now in compliance. This improvement is very substantial by world standards. It must be regarded as a creditable accomplishment by the coal mine operators, federal agencies, and mine workers involved. Most of the improvement has been brought about by the use of existing technology to control, suppress, and collect respirable coal mine dust. Research and development by the Bureau of Mines has contributed significantly to the accomplishment by improving the methods for sampling, control, suppression, and collection.

Jan 1, 1980

By G. M. Molinda

The U.S. Bureau of Mines conducted an investigation to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure and suggestions for controlling this problem are presented. Hazardous roof conditions identified in some mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52 pct of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath several valleys in the form of bedding plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomena, was found at mining depths as great as 300 ft. In situ, horizontal stress measurements beneath a valley and the adjacent hillsides, confirmed valley stress relief. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress.

Jan 1, 2010

By C. H. Elder

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coal bed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 fts/day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By Terrence J. Stobbe

The authors investigated the nature, cause and treatment of 234 back injuries which occurred in 156 different situations in underground coal mines. A detailed interview was conducted with each injured miner as 137 variables were explored to provide a complete picture of the injury scenario. The miners worked at 23 mines in six states. An important finding of the study was that sudden movement, which occurred in 527 of the injuries, is a more frequent factor than heavy lifting in causing hack injuries. Along with sudden movement, other major injury causing factors were equipment seat design, lifting, cable handling, and slips/trips. No significant differences were found between the injury scenarios associated with lost time and non-lost time injuries; thus, both sets of scenarios should he used in doe loping back injury control strategies. Medical treatment and rehabilitation varied in content and quality. Dialogue between the medical, rehabilitation and mining communities is needed to develop an effective treatment strategy. Back injury control related training was found to be inadequate in most mines. Mine specific training for physical stress recognition and potential sudden torte release should he added to the training currently given. Based on the information collected in this study, recommendations were made regarding equipment design, mechanical assists and procedures for material handling, training, etc., which, if implemented, will assist in reducing the frequency of back injuries in underground coal mining.

Jan 1, 1989

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 1997

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

By Perry N. Halstead

This report describes two goniometers that, by simple manipulation, can be used to ascertain the attitude of a joint, vein, or fracture plane observed on the planar projection of a borehole photograph taken with an NX borehole camera of the type developed by the U.S. Army Corps of Engineers. One goniometer was designed to interpret photographs taken in vertical drill holes and the other for photographs taken in inclined drill holes. In practice, several measurements are made on each photograph with the goniometer. These data are then substituted into mathematical equations, which are derived in this report and the attitudes of fracture planes are determined.

Jan 1, 1968

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By Don Belsher

Work on contract H0272007 is summarized for the period of 1 February 977 to 1 February 1978. The initial evaluation of two potential systems for the location of well casings, voids, and tunnels in coal are described. The pulse measurement equipment used for the evaluation of the antennas selected possible use with a pulse time domain system and an FM-CW system is described. A TEM horn antenna design potentially suitable for use with these systems is given. An operational comparative analysis between various antenna types is presented.

Jan 1, 1978

By Spencee L. Willett

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines conducted mineral surveys of the 20,508-acre Blue Lakes (NV-020-600) and 5,142-acre Alder Creek (NV-020-600D) Wilderness Study Areas (WSAs) in northwestern Humboldt County, Nevada. The WSAs are part of an upthrown, north-south trending fault block associated with the Basin and Range province. Both areas are predominantly underlain by the Cretaceous Duffer Peak pluton which intrudes Triassic metasediments and Jurassic plutonic rocks to the east and Permian Happy Creek volcanics to the south. In the Alder Creek WSA and in the southwest portion of the Blue Lakes WSA, Duffer Peak granodiorite and Happy Creek volcanics are overlain by Tertiary basalt. No active mines exist within the Blue Lakes WSA; but, several prospects, claims, and mineralized outcrops are in the south and northeast portions. No mineral resources were identified but samples from discontinuous, vein-type deposits contained anomalous amounts of gold, silver, copper, lead, zinc, molybdenum, antimony, and uranium. Very fine, residual gold was detected in nine alluvial samples collected from a small deposit in the southwest corner of the WSA; average gold value was $3.58 per cubic yard (at $350/ounce). Two mines, several prospects, and mineralized outcrops adjacent to the Blue Lakes WSA contain mineralized, irregular structures which do not appear to extend into the Blue Lakes study area.

Jan 1, 1986

By Byron A. Baker

The Bureau of Mines used a windowed cell to measure the phase-boundary pressures of two related series of gas-condensate fluid mixtures. Normal butane was added to the mixtures incrementally to determine its effectiveness for lowering phase-boundary pressure. All the experimental data were correlated, so that the pressure required to maintain light oils mixed with natural gas in the single phase may be computed for secondary recovery applications. The heavy hydrocarbon parts of the mixtures were distillation fractions of a Gulf Coast condensate. Intermediate normal hydrocarbons in the butane-heptane range and natural gas were added to the fractions in selected proportions, so that phase-diagram pressures of 26 fluids were actually studied. The experimental range of temperatures was 50° to 280° F. Two correlations were developed to represent phase-boundary pressures by means of a polynomial. Independent variables represent natural gas content, disparity of properties of components comprising the mixtures, and temperature. A fourth variable, for one correlation only, was the quantity of normal butane added to the original mixtures. The latter correlation with four independent variables contains 15 coefficients and is estimated to be accurate to 135 psi.

Jan 1, 1973

By K. O. Bennington

The thermodynamic properties of hedenbergite, of composition [(Ca0,9516) (Mg0,0583Fe2+0.7134 Fe3+0.0934 Mn0,1366) (Si206)], were experimentally determined at the Bureau of Mines. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -680.96±0.855 kcal/mol. The standard enthalpy of formation from the oxides is AR-96 = -24.55±0.485 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 12.3 to 300.1 K. The derived standard entropy is S-98 - 41.218±0.148 cal/mol-K. High-temperature heat capacities were measured with a differential scanning calorim¬eter from 397 to 1,147 K. These experimentally determined data were combined with data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation are given as a function of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -641.90±0.86 kcal/mol.

Jan 1, 1984

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide alumina production capacity by plant and country. The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1993. Capacity data represent announced installed and planned capacities and do not necessarily reflect a Bureau of Mines judgment of actual plant operating levels or timing of planned expansions, The year-end capacity is the ?nameplate" capacity or estimated production capacity, whichever is larger.

Jan 1, 1993

By A. B. Cecala

The Bureau of Mines has developed a pallet loading dust control system designed to lower the dust exposure of workers during the bag stacking process at mineral processing facilities. The system makes bag stacking much easier because the pallet height remains constant throughout the entire bag stacking cycle through the use of a hydraulic lift table. The system uses a push-pull ventilation technique to capture the dust generated during bag stacking. A low-volume, high-velocity blower system operating at approximately 150 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-in air jets (approximately 1,200-ftjmin velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they entrain the dust generated during bag stacking. The exhaust ventilation system pulls approximately 2,500 cfm of air and dust through the exhaust hood. This exhaust air can then be dumped into a baghouse ventilation system, or filtered before being discharged outside the mill. During a laboratory evaluation, a 70-pct dust reduction was recorded for the bag stacker. The system was then evaluated in an actual working environment. The first field evaluation was performed at a silica sand operation in which one worker performed the entire loading and bag stacking process. This worker's dust exposure was lowered 76 pet when using the new pallet loading system. The second field evaluation showed only moderate dust reduction, but this was mainly attributed to an overriding problem associated with background dust and the cleanliness of the bags. From both the ergonomic and production standpoint, the system was well received by both the workforce and plant management.

Jan 1, 1988

By Walter W. Kaufman

This report summarizes a study conducted to determine the state of the art of various rock removal systems and their capabilities. The Objective of the study was to determine if currently manufactured equipment can adequately accomplish rock removal in surface mine reclamation applications. Evaluations of state reclamation regulations, with regard to topsoil rock content, were made to determine the rock removal requirements. The major categories of equipment studied are rock pickers and rock rakes. The impact of rock removal implementation on the reclamation operations is discussed in detail.

Jan 1, 1979

By Eric E. Ungar

Some fundamental facts regarding noise are summarized. Guidelines for reducing plant noise are indicated, and simple means are discussed for determining, whether quieting of specific equipment items will reduce plant noise significantly. Design and installation recommendations are made for quieting chutes by means of dams, impact cushioning pads, impact shields, and damping materials, and for quieting; screens by means of resilient decks, lined screen bottoms, drive mechanism enclosures, and side plate additions. A brief account is appended of the wear and productivity performance of resilient materials observed in three cleaning plants.

Jan 1, 1976

By A. J. Kraemer

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the on the districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of eight. California crudes. Analyses of other crude oils from California have been published it Reports of Investigations 2595, 2608, and 2846. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting 65 samples was facilitated by the courtesy of representatives of oil companies in California. The methods used in testing and analyzing the samples are described in detail in Bureau of Mines Bulletin 207. A discussion of the interpretation of crude-oil analyses, as made by the Bureau of Mines, is given in Bureau of Mines Report of Investigations 2806.

Jan 1, 1931

By L. B. Berger

Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the dangers of this gas, and frequent now items retort the finding of persons dead or unconscious from the effects of carbon monoxide, yet these accidents continue. Either those warnings are not read, or they are unheeded by people who feel that "It can't happen to me." It can happen to you - carbon monoxide is no respecter of persons, as evidenced by items appearing daily in newspapers all over the country. Carbon monoxide has been a threat to human safety as long as man has used fire to keep himself warm and to cook his food. The burning of any fuel that contains carbon may produce carbon monoxide. This is true of solid fuels such as coal, coke, and wood; of liquid fuels such as oil, gasoline, and kerosene, and of gaseous fuels such as natural or manufactured gas. In the process of combustion the carbon in the fuel unites the chemically with tat oxygen of the air to form carbon dioxide (CO2), however, if the supply of air is not adequate, combustion is incomplete and carbon monoxide (CO) will be formed.

Jan 1, 1943

This paper on. the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States., The paper includes a short discussion of results, tabular data, and individual analyses of eight California crudes. Analyses of other crude oils from California have been published in Reports, of Investigations 2595,3/ 2608,4/ and 28465/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1931