Search Documents

By Galen G. Waddell

Dilation and contraction of the rock surrounding horizontal access open-ings of a deep mine were analyzed during stope advance to determine what type of measurements, made with relatively inexpensive instrumentation, would best reflect the rock behavior. A variety of instruments, mostly mechanical extensometers, were used. Detailed descriptions are given of Down-the-hole extensometers, floating rockbolt clusters, transit surveys, and other instruments and measuring techniques. Although all of the radial-deformation-rate graphs illustrated useful rock behavior data, the most informative graphs were compiled from data procured with the radial extensometers that penetrated, to various depths, the rock around the access openings. An analysis is given of measurement data on the rock around lateral drifts and across and adjacent to the nearly vertical vein of the Star mine, Burke, Idaho. Several useful relationships were found between the rock deformation rate and the stoping process. Information was produced on the elastic state of rock around an underground opening, effectiveness of stope support, rheology of rock, zone of influence around stopes, effectiveness of rockbolts, axis of maximum strain in a plane perpendicular to the long axis of the lateral, and other phenomena. This information could be of particular value in determining location, design, and support of underground openings.

Jan 1, 1966

This report covers the work performed by the Advanced Products Division of FMC Corporation under Bureau of Hines Contract J0155166, Design Evaluation for Development of an Advanced Bolter Module. FMC has evaluated the existing ISMS bolter designs, and the corrections and improvements in progress, including the effect of the three-chain magazine presently being fabricated, and recommends that a complete bolter module featuring a new magazine, safety post and lower stabilizer or similar device be designed, fabricated, and tested, A 29 week program is proposed which includes a four week demonstration. This module would eliminate those reliability problems not presently being solved and would provide a reliable bolter module for a production oriented miner/ bolter.

Jan 1, 1975

By John Jordan, Tesarik, Steven J. Knoll, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By H. E. Harris

An extensive experimental program was carried out to determine the variability of respirable dust samplers and to determine whether area dust sampling is feasible in coal mines. For sampler variability, it was found under laboratory conditions, that a single dust measurement could be as much as 0.30 mg/M3 from the true value at the 95% confidence level. Under actual underground mining operations, this difference could be as much as 0.52 mg/M3 in the 0 -5.0 mg/M3 range. The results from dust sampling on 175 production shifts involving over 2,500 on-man and area dust samples showed that area sampling is viable, but the field investigation did not establish necessarily where the best area locations were.

Jan 1, 1976

By Oliver Bowles

Granites are classed as igneous rooks; they have been formed by the solidification of rook magmas or Solutions from deep within the earth. It is an almost invariable law of nature that mamas which cool quickly form fine-brained or glassy rocks, while those that cool slowly are completely crystallized and are coarser-grained. Granites, being of the latter class, are regarded as having attained their solid form at considerable depth below the surface under conditions of high temperature and pressure. The constituent minerals crystallized out slowly, the crystals interlocking with one another. The great depth of overlying rocks that must have been present when crystallization took place has been removed by erosion over large areas on the surface of the earth in consequence of which granites appear at or near the surface in many localities.

Jan 1, 1930

By H. H. Schrenk

One phase of Bureau of lines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that devices embodying these features will be available the Bureau has established schedules of minimum requirements for oxygen breathing apparatus, gas masks4/, supplied-air respirators (hose mask, air-line respirators, and abrasive blasting helmet hoods, or masks)5/, and dispersoid (dust, fume and mist) respirators6/. Approval test, of oxygen¬-breathing apparatus are conducted by the Safety Division; approval tests of other types of respiratory protective equipment are conducted by the Health Division. These divisions comprise the Health and Safety Branch.

Jan 1, 1941

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By Nan C. Jensen, Oliver Bowles

"INTRODUCTION Limestone (which consists essentially of calcium carbonate) and dolomite (calcium magnesium carbonate) occur widely in the United States. Their presence is of vast economic importance, because they are used much more extensively than any other form of rock. In 1945, limestone (which, broadly, includes dolomite) was quarried in every State except Delaware, New Hampshire, North Dakota, and Rhode Island, and also in Hawaii and Puerto Rico. Total production (including that used in cement and lime manufacture) exceeded 151,700,000 tons, or 79 percent of the quantity of all kinds of stone sold or used during that year.Important well-known uses of limestone are as concrete aggregate, road material, railroad ballast, for liming the land, for cement manufacture, as riprap for shore protection, harbor work, and spillways at dams, and as building stone.. None of these uses, however, are considered herein. The purpose of this paper is to discuss the industrial and chemical uses that are less widely known and yet are of tremendous importance in a great variety of processing industries. Important examples are dolomite as a refractory furnace lining and limestone as a fluxing agent in blast furnaces, and as a raw material employed in sugar, paper, glass, and alkali manufacture.PRIOR REPORTIn May 1941, the Bureau issued a report 4/ that described these uses in some detail. As new and important developments have taken place during the ensuing years, a revision and representation of the salient features of these uses seem desirable. Asphalt filler and mineral wool uses included in the earlier report are omitted from this paper because they are identified more closely with the highway and building industries, respectively, than with the industrial applications."

May 1, 1947

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July l, 1936.

Jan 1, 1940

By Wesley Hermanson

Canopies were designed, fabricated, installed, and demonstrated for mining machinery in 3-foot coal seams. A Wilcox PJ20 Auger miner, a Wilcox Bolter, a bee Norse 245 miner, and an Elkhorn Scoop AR3 modified to AR4 were fitted with canopies. The Wilcox Bolter canopy was hydraulically adjustable in height; the rest were manually pin adjustable. The machine operators' comments were adverse in each case. Restriction of visibility and body constriction into unaccustowed and tiring attitude were major objections, causing increased hazards and fatigue. Recommendations are made that roll bar protection be furnished in place of canopies for 3-foot seams to provide partial protection by deflecting and supporting roof falls but not covering the head of the operator. In this way, the effect on visibility would be minimized and fatigue from body restriction would not be increased.

Jan 1, 1976

By Gary P. Sames

This U.S. Bureau of Mines study was conducted in eastern Kentucky drift mines as part of an ongoing research program to characterize the outcrop barrier zone. "Hillseams" were identified as the dominant geologic cause of roof instability unique to the outcrop barrier zone, with many roof fall injuries and fatalities attributed to them. Hillseam is the eastern Kentucky miners term for weather-enlarged tension joints that occur in shallow mine overburden where surface slopes are steep. Hillseams are most conspicuous within 200 ft laterally of a coalbed outcrop and under 300 ft or less of overburden. Hillseams form by stress relief, and therefore tend to parallel topographic contours and ridges. They can intersect at various angles, especially under the nose of a ridge, and create massive blocks or wedges of roof prone to failure. Examples of hillseams are described in both outcrop and in coal mine roof to establish their geologic character and contribution to roof failure.

Jan 1, 1989

1. Proposals were submitted to the Western Administrative Center of the US Bureau of Mines, Denver, Colorado on 30th December, 1974 and Contract No J 0255003 was awarded, the effective date being 8th May, 1975. Dames and Moore, Denver, are associated with PD-NCB Consultants in regard to environ-mental problems, surface mining practice and legislation in US. BACKGROUND TO THE STUDY 2. Under the threefold pressures of -increased domestic fossil fuel demand -increased value of domestic energy resources -increased demand for environmental protection and safety

Jan 1, 1976

By Joseph Coffman

There are 14 operations that supply 97% of the Market Economy Country (MEC) manganese and contain nearly all of its resources. Six mines account for about 70% of the production and 85% of the resources; there are no known resources that are economically close to those that are currently being mined. Costs (January 1989 dollars) of producing manganese concentrates from the operations evaluated are estimated to range from $ 0.96 to $ 1.86 per long ton unit (ltu or 22.4 lb) of contained manganese. Total MEC demonstrated resources evaluated amount to about 1.2 billion tons of in situ ore containing 474 million tons of manganese. Identified resources amount to about 1.8 billion tons of in situ material. Key results of the study indicate the following: 1. The MEC supply of manganese will be from the currently mined resources well into the next century. 2. Centrally Planned Economy Countries (CPEC's) will be increasingly dependent on MEC manganese ore and concentrate in the future. 3. At the 1976 to 1987 demand increase rate, total MEC resource needed through the year 2000 would be about 282 million tons of in situ material. 4. Transportation and infrastructure support will continue to be major elements of production costs.

Jan 1, 1992

By Oliver Bowles

The manufacture of lime is one of the oldest industries. Plants are distributed widely and furnish an essential raw material for numerous industries. The use of lime by the building trades, in agriculture, and in hundreds of manufacturing and chemical processes has created demands for a large production and has necessitated exhaustive research on methods of manufacture and uses. The bibliography of lime is an extensive one, but for the most part each publication has dealt with only certain operations. The purpose of this paper is to present a general picture of the industry as a whole. The abundant literature has been abstracted and quoted freely, and the National Lime Association has rendered valuable assistance in furnishing data for certain sections. Publications containing more detailed information on the various branches of the industry are referred to in the footnotes and in the bibliography.

Jan 1, 1936

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By Joseph M. Pugliese

The Bureau of Mines through its contract research program recently analyzed the mining and environmental requirements in the premining stage for copper mining in the northern highland of Wisconsin. The Critical-Path-Method (CPM) was used in this research. However, a step-by-step derivation of the CPM Diagram was beyond the scope of this effort. The Bureau of Mines objective now is to show, step by step, how the original hand-computed CPM Diagram was constructed. The streamlining (restructuring) of this diagram from the original effort is also summarized. The critical path time (longest time) through the original CPM Diagram was 25.12 yr, excluding public liaison effort. This diagram showed the involvement of the regulatory agency, mining applicant and public in the premining stage. Analysis of this diagram produced a streamlined version which reduced the critical path time by nearly 7 yr. The CPM construction methodology offered here may be applied to mine planning for any mining operation.

Jan 1, 1983

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about 1/2-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15. 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black. Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By Glenn A. Shirey

The objective of this contract as to prepare a detailed, readily usable handbook on dust control techniques for longwall mining operations. Information was gathered from available literature, and through contacts with industry and government personnel. The handbook describes those methods of dust control applicable to today's longwall mining systems, and contains sufficient design elements to assist operators with problems in testing or implementing new control procedures. Complete reference lists are presented at the end of each chapter to direct the reader to additional information.

Jan 1, 1985