Search Documents

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014

By Williams Calderon, César Arredondo, Gonzalo Montes-Atenas

The quality of final concentrate in froth flotation circuits is largely dictated by the correct implementation of the froth washing operation in flotation cleaning stages, which are commonly installed in column flotation cells. In flotation plants, this aspect has been largely overlooked and the froth washing is restricted to the use of perforated piping through which process water flows producing a similar effect to that observed in "fountains": jet created with low energy crosses the froth phase washing out entrained particles as well as particles weakly attached to bubbles. The aim of this research study is to assess the efficiency of traditional froth washing systems theoretically and experimentally. A theoretical model was implemented using Fluent® software where a jet of variable speed was introduced in a continuous soft matter phase with physical properties similar to those observed in a froth phase in wet and dry conditions. In addition, a simple experimental protocol was designed to validate the model. It was found that the water process jet-like flow influences the behavior of 2 to 3 times the equivalent volume in the froth phase. Such influence zone is dramatically reduced as the froth phase becomes drier. These results were confirmed by the experimental findings indicating that a better froth washing technologies must be assessed and implemented. Some aspects of the ideal froth washing system are derived and discussed in details.

Jan 1, 2014

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Luís Marcelo Tavares, Juliana Segura

Comminution is one of the most energy consuming stages in a mineral processing plant. This consumption is not only related to the power supplied to equipment, but also to the indirect or embodied energy, mainly associated to materials that are worn during operation, including grinding media and liners. Until recently, preparation of iron ores in Brazil did not use comminution intensively, given that plants mainly produced sinter feed, natural pellet fines, besides lump ore. However, with decreasing ore grades, size reduction now occupies a centre stage in nearly all new plants. Technologies used up to date for processing low-grade iron ores in Brazil, in particular itabirites, have consisted of three or four stages of crushing followed by ball milling. A number of new plants are either being built or are currently being designed that will process the same type of ore, so that engineers are investigating alternative comminution routes. The paper analyses comparatively four comminution routes for processing a particular itabirite ore, many of which using technologies and layouts that have not yet been used in such application. Using data from bench scale and/or pilot-plant tests, the different routes are compared on the basis of sustainability principles in accordance to the Brazilian energy matrix, which is quite particular. It is concluded that if the sustainability criterion is used, then the optimal route would correspond to a circuit that uses HPGR technology with truncated feed followed by ball milling. Given the particular case of itabirite iron ores and specially to the one in the present work and the source of Brazilian energy, it is evident that indirect energy expenditure in comminution plays a significant role in greenhouse gas emissions when compared to direct energy, being the reason for the great attractiveness of HPGR technology. Evidently that these will have to be balanced against CAPEX, OPEX, NPV and other qualitative criteria, which can certainly lead to a different optimal circuit.

Jan 1, 2014

By S. A. Vorobyev, Yu. L. Mikhlin, Ye. V. Tomashevich, A. A. Karacharov, M. N. Likhatski1, A. S. Romanchenko, S. V. Saikova

"A set of state-of-the-art methods have been applied to study ultrafine particles and nanoscale species arising on mineral surfaces upon milling, interaction with flotation reagents, and leaching of base metal sulfide ores in order to gain insights into interfacial mechanisms. The fine fractions produced by ball milling of a Pb-Zn Gorevsky ore and four Cu-Ni sulfide ores studied with laser diffraction, dynamic light scattering, zeta-potential measurement, Xray photoelectron spectroscopy (XPS), SEM, TEM and other techniques. The particle size distributions had, aside from the peaks at 20-60 ?m, maxima near 1-2 ?m; the flotation was considerably suppressed when the yield of positively charged ultrafine particles approached tenths % (several kg per ton). High-energy XPS and X-ray absorption spectra revealed that sulfide minerals depleted in metal in air and aqueous solutions were composed of outer “polysulfide” layers, strata with disulfide species, and heavily defective underlayers, and “passivation” was explained by stability of the metal-deficit structures. Dixanthogen at pyrite and copper-activated sphalerite, dixanthogen and then cuprous xanthate on chalcopyrite, and chemisorbed xanthate at galena were specified as the main interfacial products using cryo-XPS of fast-frozen flotation slurries. The particle size, zeta-potential and behavior of colloids of Cu and Pb xanthates and dixanthogens were largely determined by the initial ratio of a cation and collector; the properties of copper xanthate nanoparticles were also affected by incorporated dixanthogen (about 15 wt.%). Submicrometer gas domains of 3-8 nm in height and “hydrophobic” forces upon the probe retraction were found on xanthate-treated minerals using atomic force microscopy and spectroscopy; their impact on flotation is briefly discussed.INTRODUCTIONInterfacial phenomena play a key role in flotation, leaching, water purification and related environmental processes. The mineral processing and extraction of metal from sulfide ores commonly involves milling the ore, which produces, along with the particles of 20 µm to 100 µm, mineral entities ranging from micrometer to submicrometer and nanometer scale. Furthermore, ultrafine particles of flotation reagents, products of metal sulfide oxidation, and so on may form spontaneously and accumulate in production water, flotation froth, deposit on mineral surfaces, affecting the flotation performance, and then enter waste waters, mine and natural drainage, polluting soils, surface- and ground waters (Miettinen et al., 2010; Wang et al., 2014). The efficiency of flotation and hydrometallurgical recovery of values, environmental issues are crucially dependent on the state of mineral surfaces. Particularly, it is generally accepted that the surface non-stoichiometry of sulfide minerals induced by oxidation and leaching should affect their hydrophobicity and reactivity, including so-called “passivation”, but the nature of such surface layers are still a matter of controversy (see, for example, Holmes and Crundwell, 2013). Another phenomenon attracting rapidly growing interest in several areas is low-dimensional gas species (“nanobubbles”) at hydrophobic surfaces that may play a decisive role in particle-bubble attachment in flotation but remains scarcely investigated up to now (Xing et al., 2017). Here, we survey our recent results on the abovementioned problems applying a series of rather new methods and approaches; more details can be found in refs. Karacharov et al., 2016; Mikhlin et al., 2015; 2016; 2016a; 2016b; 2016c; 2016d; 2017; 2017a; Vorobyev et al., 2017."

Jan 1, 2018

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By Hakan Gürsoy, Kemal Bilir, Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"Jet diffuser flotation column (JDFC) is a flotation device resembles Jameson flotation cell (JFC) in terms of operational principles, but it has significant difference structural points of view. This difference is an essential change in the downcomer to provide an increase of performance of the cell for the coarse particles. By using the hydrodynamic and fluid mechanics principles (Sahbaz et al., 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogeneous dissipation of the bubbles in the separation tank. According to experimental results carried out in pilot scale JDFC, not only higher flotation performance comparing with Jameson cell was obtained specifically for coarse talc particles in a certain condition, but also quiescent froth layer was acquired. In these tests, vertical pipe of JDFC having inlet diameter of 6 cm and outlet diameter of 11.5 cm was used with separation tank having the diameter of 39 cm. By using the data, pilot scale JDFC having 410 cm vertical pipe integrated with separation tank was produced and flotation tests were carried out by using the naturally hydrophobic mineral (talc). Finally, the talc recovery obtained as 94% by the use of JDFC, while Jameson cell has the recovery of 77% for the particle size of 250 µm."

Jan 1, 2014

By T. Fujita

A high-grade fluorite ore is converted into hydrogen fluoride to produce many kinds of materials containing fluorine. Recently, it is becoming necessary to use low-grade fluorite ore due to the depletion of high grade ore. The low-grade fluorites usually have impurities such as SiO2, P, CaCO3 and arsenic. The most impurities such as SiO2, CaCO3 and P can be removed by using flotation method. However, the removal of arsenic is difficult, and the arsenic contamination decreases the hydrogen fluoride production percentage. The novel technologies for processing low-grade fluorite ore are urgently needed, in order to lower the arsenic concentration to less than 100 mg/kg. In this study, the removal of arsenic from low-grade fluorite ore has been investigated by means of an autogenous grinding using tower mill in sulfuric acid aqueous solution and 0.3 mm zirconia balls in water. The nano grinding in water can prevent the dissolution of 0.3 mm size zirconia balls as grinding media by sulfuric acid solution. Experimental results showed that the arsenic concentration was reduced from 260 mg/kg to 90 mg/kg and CaF2 recovery reached 90% by this process.

Sep 1, 2012

By Cristian Melipichun, Leopoldo Gutierrez

The effect of the presence of fine particles of kaolinite and montmorillonite on the induction time for attachment of bubbles to particles of a copper concentrate rich in chalcopyrite was evaluated in this study. The results obtained from induction time measurements were correlated with data of concentrate recovery achieved from micro-flotation experiments. The effect of the presence of fine clays on the stability of air-water foams was also studied through measurements of the foam volume generated in a glass column under different conditions of air flowrate and MIBC concentrations. The experimental results showed that induction time values increased under the presence of fine clays. These data agreed with results obtained from micro-flotation experiments that showed that copper concentrate recovery decreased when clay particles were added. Although a complete explanation for these results is not available, the fact that experimental observations indicated that fine clay particles tend to adsorb on gas bubbles, suggests that the interactions between fine phyllosilicate particles and air bubbles have to be taken into account when studying the effect of clays on froth flotation. Foamability tests showed that the presence of fine clay particles increased the foam volumes only at high additions of clays and low dosages of MIBC. The results obtained at higher dosages of MIBC showed that the foam volumes decreased with the addition of clays under all the experimental conditions tested.

Jan 1, 2014

By Douglas Fuerstenau

"Comminution not only is the major energy cost in mineral processing but it also can limit the grade of ores that can economically be processed. Rittinger first postulated that the energy for comminution is proportional to the new surface produced. Because most of the strain energy needed to initiate and propagate cracks in particles cannot be recovered, researchers reported woefully low comminution efficiencies. Recognizing this, Schoenert proposed that the baseline for assessing comminution efficiency should be the mechanical energy needed to break single particles. After extensive single-particle studies, Schoenert turned to comminuting beds of particle in piston dies. Finding particle-bed comminution to be energy efficient, he had the brilliant conception of making the process continuous, namely his invention of the choke-fed high-pressure roll mill (HPGR). Practical comminution involves masses of particles, which can lead to energy efficiencies far less than that of single-particle breakage. A three-way classification of grinding modes in terms of the mobility of the particle mass provides the necessary insight into the low efficiency of different comminution machines: namely, single-particle breakage, confined particle-bed grinding (HPGR), and loose-bed grinding (ball mill). Examples are given for determining and comparing comminution efficiencies. The size distribution of comminuted products become self-similar, and a single parameter, the median size, can be used to quantify the extent of comminution. The reduction ratio, expressed in terms of the mean size of the feed and product, varies linearly with expended energy and the slope of such plots is a measure of the grindability of the mineral. This approach clearly gives the order of energy efficiency as single-particle > particle-bed > loose-bed comminution. HPGRs are more efficient at low reduction ratios but lose that advantage at higher reduction ratios. Extensive hybrid grinding experiments carried out with our instrumented ball mill and HPGR showed significant energy savings by first comminuting the material in the HPGR and followed by the ball mill. At Cerro Verde an industrial-scale hybrid HPGR/ball mill system is reported to have a 13 percent energy savings over a SAG mill/ball mill system."

Jan 1, 2014

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By P. Banerjee, P. Dash, S. Sriramoju, A. Suresh, R. Lingam, T. Ray

"One single property that influences the quality and market value of coal to the maximum extent is the ash content. The lower the coal ash higher is the energy utilization and potential for different applications. Even though Indian coal washeries aspire to produce coal with low ash, the intimate distribution pattern of ash bearing minerals in the coal matrix becomes the real bottleneck, as it brings down the clean coal yield to the impractical value. Because of this fact, most of the Indian washeries are operated to produce coal with 14-15% ash content at the yield of around 40%. In this context, with an objective to produce low ash coal at higher yield, a novel chemical beneficiation route has been explored to demineralize the high ash containing Indian coals. In this present work, the production of low ash clean coal from high ash Indian coals using chemical leaching process has been studied at pilot plant level. The leaching process parameters such as reaction temperature, reagent concentration, reaction time, coal-liquid ratio and agitator speed have been optimized for the flotation tailings sample from a captive washery of Tata Steel. The results obtained show that 67% demineralization could be achieved in a single stage of leaching process with a product yield of more than 65%. For further demineralization, multistage leaching was carried out and the results showed that 75-85% demineralization could be achieved with significant reduction in alumina to silica ratio. Additionally, the phosphorus content is also significantly reduced from 0.20 % to 0.022 %. Further, it is interesting to note that there is no increment of sodium content in the product coal after chemical treatment."

Jan 1, 2014

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Christopher Greet, Alfred Van den Bosch

"A range of media alloys with different chromium content has been developed for different milling applications. When selecting the grinding media alloy for a specific application, consideration must be given to the mineralogy of the ore as well as the water chemistry and mill operating conditions. The paper describes the influence of the microstructure of the alloy on the wear resistance and the influence of the chrome content on the pulp chemistry and downstream processing. It also provides information about the in-house tools which Magotteaux have developed to predict the media wear rate with different chromium content alloys and predict their flotation efficiencies that can be expected when the right alloy is selected for a particular application."

Jan 1, 2014

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014