Search Documents

By Mary Ellen Bruce

Let me first address the issue of the wet grab samples. The wet grab samples that were attempted to take on the Central Artery were hindered by the fact that the way the mixing was being done was only by injecting grout on the way out, during withdrawal of the mixing tools. They would auger down to the required depth (usually with some water being injected), which took anywhere from 45 minutes to an hour, and then when coming out, the grout would be injected with grout. That was leaving a column of grout in the center where the shaft had been (i.e. inside of the blades of the mixing tools), which would end up being something like a foot in diameter because the pipe that was used for the drill shaft was a foot in diameter. So we had 10 inches to a foot of almost pure grout in the middle of our column and then we had 2 feet on either side that was mixed soil cement. So when they went down with the wet grab sampler not knowing where that was in the column sometimes they/we were getting strengths of 1500 psi, and sometimes they/we were getting strength of 500 psi or 100 psi. So what was it that we were taking into the wet grab sampler? In those cases you don't really know, but it wasn't representative of the core samples we were taking. We were purposely not coring in the center because we knew that was going to be high cement content, almost pure grout. So the issue of wet grab sampling particularly on this project, the Central Artery Project, was that we didn't really know what we were sampling. What becomes an issue with wet grab sampling in other projects is that you have to have another device (machine) in most cases, a cherry picker crane or something similar that can raise and lower with a beam that is used to forces the sampler down into the freshly mixed soil-cement. And regarding economics, is it more economical to have that crane standing by with its operator or to have a drill rig to come along later and do the coring and take the material out that's fairly identical to what you're finding in situ? The complaint of micro-fracturing in the core samples as you're taking the cores was raised by Seiko as causing large strength reductions. But, if you're doing it carefully, then I don't think that's much of an issue anymore, on research basis perhaps but not on a practical level.

Feb 10, 2003

By L. J. Whitworth

Five trial piles were constructed during the trial pile programme for the Birmingham International Convention Centre. In addition, trial piles have been tested on two other sites in central Birmingham. Methods of pile construction were conventional sandstone rock sockets, sleeved piles and voided piles. The results of these load tests are compared with the theoretical predicted behaviour based on the results of unconfined compressive tests of rock core taken on the Convention Centre site and on other sites in the central Birmingham area. On the basis of this work, the various design procedures are discussed.

Jan 1, 1989

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

By Frank Haehnig, Harald Krenn, Harm-Christoph Claassen

"The Wadi Dayqah Dam Water Supply Scheme represents one of the most important projects implemented by the Sultanate of Oman to ensure sustainability of water resources. The principal components of the project comprise two dams to impound the Wadi Dayqah, to store and supply drinking water to the local area and to Muscat, the capital city of the Sultanate.The Main Dam with a central spillway is a RCC Gravity Dam with a maximum height above foundations of 75m, crest length 400m; the Saddle Dam is a rockfill dam with central clay core, max height above foundations is 49m and crest length 360m. During construction of the Saddle Dam a key trench was excavated to 10m depth and filled with compacted clay connected to the central core of the embankment. Grouting utilizing cement grout was performed as a single line grout curtain prior to each filling operations. Both Dams are founded on soft Siltstone, Claystone, Sandstone and inter-bedded harder limestone.After construction of the Saddle Dam, once water was in the reservoir it became evident in early 2010 that some seepage was occurring apparently from the right abutment. This seepage became more marked when the reservoir first filled to discharge over the spillway in June 2010. In order to reduce the seepage, additional sealing works by drilling and grouting of a three row curtain up to 80 meter target depth were initiated to supplement the existing single row curtain. Part of this project for the sealing works has also been to drill additional investigation holes to provide more information and confirm extend of the additional sealing works and its limits.Züblin Ground Engineering was awarded the Additional Sealing Works Contract. Whilst Equipment was on Site, the opportunity was taken to carry out drilling and grouting on the Left Abutment of the Main Dam to reduce seepage through that abutment and to install additional standpipe piezometer for future monitoring of seepage patterns.Work on this Contract started on site in January 2013 and was substantially completed in January 2015.At the time of Tender Züblin Ground Engineering propose and Alternative Design in the form of a Secant PileCut-Off Wall, 85m long to a depth of 40m with additional drilling and grouting below the foot of the cut-off which was then included in the contractual scope."

Jan 1, 2016

By Fred Tarquinio, Giovanni Bonita, Lars Wagner

"A new embassy for the Peoples Republic of China is under construction in Washington, DC. The 475,000 square feet (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. A vertical soil nail wall was used as the primary support of excavation system for the project. The soil nail wall was irregularly shaped, benched in areas, and up to 98 feet (29.9 m) in height. The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Design and construction challenges included soft soil conditions, inside wall corners, underground utilities, seismic impacts from blasting, and logistical and political factors. Overall, wall movements were lower than expected, with maximum horizontal movement less than 0.25% of the total height of the excavation. INTRODUCTIONThe proposed Embassy of the Peoples Republic of China in Washington, DC, will consist of about 475,000 ft2 (44,125 m2) of building space and contain up to four fl oor levels above ground and fi ve levels of basement (Figure 1). When completed, the building will be the largest embassy in Washington, DC. The architect for the project, Pei Partnership Architects, along with the world-renowned architect I.M. Pei, made effi cient use of the site by inserting the building into the existing slope. Consequently, excavations reach heights up to 98 feet (29.9 m) on the southern side of the property and 42 feet (12.8 m) on the northern side.The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. The location of the building relative to the property line called for tight excavation requirements, including precise wall positions and shotcrete tolerances. Design and construction challenges included soft soil conditions, inside wall corners, arched walls, underground utilities, seismic impacts from blasting, and logistical and political factors."

Jan 1, 2007

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By David K. Crapps

The drilled shaft load tests at Port Orange were part of a demonstration project sponsored by the Federal Highway Administration (FHWA) and the Florida Department of Transportation (FDOT). Three load tests were conducted. Test 1 was a conventional test with the test shaft loaded from the top. Test 2 included an Osterberg load cell at the tip and a conventional load test from the top. Test 3 used an Osterberg load cell at the tip of a production drilled shaft. All three test shafts were socketed into limerock and were carried to failure. This paper describes the test program and presents a summary of the test results. Figure 1 presents some photographs of the load test setups and Figure 2 shows the location of the drilled shaft load tests. SITE CONDITIONS The Port Orange Bridge is located on US A1A over the Intercoastal Waterway in Port Orange, Florida (south of Daytona Beach). The new bridge will provide four lanes of traffic with a 65 foot vertical clearance for Intercoastal Waterway traffic. The channel and flanking piers will be supported by 54" drilled shafts socketed into the rock. The bridge is being constructed in two phases. The southern half will be completed first, the old bridge removed and then the northern half will be constructed. The first phase is scheduled to be opened to traffic in October 1989. Each of the four piers near the channel will be supported by 12 drilled shafts with 6 shafts per pier being constructed in each phase.

Jan 1, 1989

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative "In-the-Wef' technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully Implement this technology.

May 11, 2007

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By Ryan Law

Ground energy systems are being installed in increasing numbers in the United Kingdom. This is particularly true in London where planning regulations require larger scale developments to provide at least 10% of their entire energy demands from renewable sources. A common approach has been to use the groundwater from the Chalk aquifer as a source of energy. This paper explains the potential long and short term sustainability problems with groundwater based systems sited in central London (or any other urbanized area). It also outlines an approach to site testing and numerical modelling to ensure that the system functions well throughout its lifetime. This approach is then applied to a project located in central London.

Jan 1, 2008

By H. (Sam) Salem

A site investigation for a wide and tall hotel building, in the San Juan Bay area, Puerto Rico, indicated a soil profile of silty clay on sand, soft and loose enough to require piled foundations. The apparent uniformity of the soil profile across the site indicated that a single pile driving and termination criterion could be applied to the installation of the piles ? driven precast concrete piles. Because of the size of the site and importance of the project, the project also included a static and dynamic testing programme. The dynamic monitoring using the Pile Driving Analyzer (PDA) verified a consistent hammer operation. However, the results of the static loading tests showed significant and inconsistent variation in pile capacity between locations and little correlation between end-of-driving and restrike penetration resistances (blow-counts) and pile capacity. Therefore, it was not possible to rely on a simple depth and blow-count termination criterion for the site. In contrast, pile driving response in terms of measured reflected force and mobilized resistance coupled with CAPWAP analysis gave a reliable correlation to the results of the static loading tests. As presented in the paper, the dynamic testing programme was enlarged and used to develop and verify a complex set of termination criteria tailored for the multitude of conditions encountered across the site to achieve and ensure economical and safe pile installation.

Jan 1, 2008

By Ambarish Ghosh, Subhaprasad Chakraborty

"Construction of basement floors has become necessary to meet the requirement of parking in office and residential complexes and in hospitals for radiotherapy treatment. Important projects coming up in Kolkata are mostly in closer proximity of residential buildings, office buildings and historical monuments. Sheet piling is mostly used as temporary shoring system during construction. Deep excavation in urban environment creates great problem related to construction induced vibration due to driving of sheet piles for basement, pile driving etc. which raises the chances of damage of adjacent buildings and nearby structures. Vibratory sheet-pile driving is the most common method of sheet pile installation. The knowledge of induced vibration due to this phenomenon is still very deficient. This paper presents the analysis of measured vibration data collected from different sites of Kolkata with varying soil profile. Typical two case studies of sheet pile and pile driving has been presented and the vibration values are analysed. The responses of the vibration are reported in terms of peak particle velocities (PPV). To evaluate the effects of vibration due to pile driving two aspects have been considered: the effect of the energy entering the ground from the pile and the effect of the soil condition.INTRODUCTIONIn urban areas infrastructure development projects are mainly located adjacent to existing structures like residential buildings, offices and historical structures. The construction work of such project influences the surrounding environment as well as human perception (Wiss 1981). During the construction of basement for residential complexes and hospitals sheet piling is mostly used as temporary shoring system or as to support the earth mass. The vibration induced due to driving of piles and sheet piles have been presented herein. Deep excavation projects close to existing structures increase the concern of environmental impact. For this reason the vibration assessment and prediction has become a subject of great interest. It is important to develop a site specific model for predicting the ground vibration resulting from pile and sheet pile driving at the construction sites. The developed model gives the efficacy to guide the engineer to select the construction methodology ensuring the safety of the surrounding structure. The model developed here is site specific and the parameters that has been used are dependent on the soil condition and the energy source."

Jan 1, 2015

By Abhijit R. Sheth, Craig M. Benedict, John Brun, Ara G. Mouradian

"Amtrak recently replaced the 1907-era bascule two-track bridge over the Niantic River between East Lyme and Waterford, Connecticut. The project included new approach embankments, with approximately 2,500 lineal feet of retaining wall along the west approach and 780 lineal feet of retaining wall along the east approach. The paper focuses on the design and construction of the east approach retaining wall, whose alignment is directly adjacent to an existing wetland area which required protection. An anchored prestressed concrete sheet pile retaining wall was selected for the east approach. A combination of concrete anchor piles and ground anchors were used to support the wall. The design of the wall took into account two simultaneous train live loads, support of electric traction catenary structure foundations, and construction live load, while at the same time preventing permanent impacts to the adjacent wetlands. The design considered challenging subsurface conditions, shallow groundwater, the close proximity of the existing operating tracks, construction staging, and storm surge events in Long Island Sound.INTRODUCTION AND PROJECT HISTORYThe National Railroad Passenger Corporation (Amtrak) recently replaced the 1907-era bascule two-track bridge (No. 116.74) over the Niantic River, between East Lyme and Waterford, Connecticut, along the heavily-traveled Northeast Corridor (NEC). The two NEC tracks, which carry over 50 trains per day, run east-west over a narrow spit of land known as “The Bar”, which separates the Niantic River’s marine estuary to the north from the Niantic Bay to the south, before crossing the river. The bay is an arm of Long Island Sound and is occasionally subject to storm surge from hurricanes.The 1907 bridge was built as a replacement for the previous 1891-era swing-span bridge, and was constructed parallel to, and 49 feet north of, the swing-span structure. The two-track 1907 bridge consisted of a single-leaf bascule span and four approach spans supported on stone masonry piers and abutments. The new bridge increases horizontal navigational clearance for marine traffic in the river from 45 feet to 100 feet, and vertical clearance from 11.5 feet to 16 feet above mean high water with the bridge in closed position. The new bridge, constructed 58 feet south of the 1907 structure, features a single-leaf bascule span of 141.5 feet, with an approach span on either side."

Jan 1, 2017

By Bill Shea, Gordon King

"For a drainage channel built in San Juan, Puerto Rico, a value engineering (VE) proposal incorporating a secant pile top-down approach saved time and facilitated construction work on the larger flood control project. The channel, at the Bechara Industrial Area, Puerto Nuevo Port Facility and the Puerto Rico Maritime Shipping Authority Dock, was needed to allow drainage of the Rio Puerto Nuevo into San Juan Bay. The port area, one of the busiest in the Caribbean, has over 6,000 ft (1,800 m) of berthing wharves for ocean-going container ships along with over 500,000 sq ft (46,000 m²) of container loading and unloading areas, and is critical to the local economy.Planners wanted to minimize the impact of construction to the port and dock users, and developed a construction methodology and work sequencing that would prevent a complete barrier to port traffic. This plan involved non-contiguous and limited work area that “leapfrogged” along the alignment so as to prevent long barriers to lateral traffic movement across the culvert alignment.After reviewing the project plans and schedule, Morris-Shea Bridge Company (MSB) proposed an alternate design and construction approach that provided significant cost and schedule benefits, and also provided better access for the port and dock users. The alternate VE proposal involved top-down construction methodology and redesigned drainage culvert geometry with two parallel 2,000 linear ft (lf) (600 m) secant walls installed on each side of the culvert. These walls facilitated excavation and formed part of the culvert permanent walls. The result was a significantly reduced required construction right of way that allowed construction work in contiguous areas largely without impact on ongoing port activity. MSB conceived the design concept, and engineered design and construction of the VE alternate secant pile culvert.The project initially consisted of an open channel in the industrial area picking up water from the existing Rio Puerto Nuevo, transitioning to an enclosed culvert through the port and dock areas, and outfall through the existing dock. The base bid construction included three main areas of work:"

Jan 1, 2012

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Dale E. Berner

A new navigation dam at Olmsted on the Ohio River will be built "in-the-wet" using a lift-in construction method by the Washington Group/Alberici Joint Venture for the U.S. Army Corps of Engineers, Louisville District. Up to 4,000-ton precast concrete dam shell segments will be prefabricated on the Illinois riverbank and lowered into the river on a marine skidway and cradle. A 4,500-ton capacity catamaran crane barge will lift the precast concrete shells and lifting frames from the cradle, and transport them partially submerged to a piled foundation pre-installed underwater. Tremie concrete will be used to compositely connect the shells, piles and sheet pile cut-off walls. This paper focuses on the pipe-pile foundations for this half-mile long navigation dam, and for the temporary precast yard and marine skidway. The dam foundations are designed to resist large ground motions from the New Madrid Fault Zone, and selected production piles are designed to serve as landing piles to support the shells during the construction process. Specific foundation issues addressed in the paper include: pile load tests; production field testing requirements; controlled fixity 24-inch diameter pipe-pile design including seismic considerations; cut-off wall design; sheet pile cellular fixed weir design; isolation jOint design; and temporary works foundation designs for both the precast yard and the marine skidway, including testing of 42-in diameter pipe piles.

May 11, 2007

By Miguel E. Ruiz, America L. Fernandez, Miguel A. Pandon

"Post-grouted drilled shafts (PGS) are a deep foundation system in which grout is injected at high pressure throughout the tip after the drilled shaft has been installed. Pressure grouting of drilled shaft tips can significantly increase the ultimate capacity and stiffness of drilled shafts. Conventionally constructed drilled shafts usually require higher axial deformation to develop the available side friction and the tip resistance simultaneously. They also tend to have higher tip compressibility and reduced end bearing capacity due to disturbance at the bottom of excavation during drilled shaft construction. PGS foundations have been found to be a cost-effective solution to compensate for this capacity reduction and/or compressibility increase. PGS construction procedure counterbalances tip compressibility and end-bearing capacity reduction. The tip grouting also has a pre-stressing effect over the shaft side friction since the drilled shaft tends to move upwards during the pressure grouting of the tip. After grouting, a bulb tends to form at the pile tip pre-compressing any disturbed material and, in certain cases, increasing the tip area, thus increasing shaft tip capacity.PGS load-settlement predictions using a load transfer approach are presented in this paper and compared with corresponding load test data. The paper also presents the main findings of load transfer analyses that were carried out to investigate the potential different factors that may be contributing to the observed improved performance of PGS over conventional drilled shafts. Results show that the two main factors, that may have a significant contribution on the overall performance of the foundation by increasing its ultimate capacity at any given level of settlement, are the stress-reversal of the skin friction and the formation of a grout bulb at the tip. The grout bulb tip contributes primarily through the increased tip area and to a lesser extent through increased stiffness and strength of the soil in the vicinity of the pile tip."

Jan 1, 2005

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Edward C. Clukey

"Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed.During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor’s QA/QC program should be increased to achieve a foundation system with the required level of reliability.Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially “at-risk”. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.IntroductionThe foundation support system for the process train at a major LNG facility comprises more than 6,000, 23-m long DMM elements. The general subsurface stratigraphy at the project site comprises (from the ground surface): (i) up to 8 m of fill sand initially placed underwater building to a stable construction platform; (ii) up to 12 m of soft organic clay (Unit II clay); and (iii) clayey sand and sand layers becoming progressively denser with depth (Unit III sands). Each DMM element comprised two secant 1.5-m diameter DMM columns. DMM elements were typically arranged as cells enclosing one, two, or three DMM elements."

Jan 1, 2017