Search Documents

By H. Al-Kazzaz

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded using 1.6 mm EZ33A-T5 filler wire and a continuous wave Nd:YAG system at a power of 4 kW, surface defocusing and various welding speeds, Compared with the base metal, the fusion zone showed significant grain refinement due to high cooling rate, No grain coarsening was observed in the heat affected zone (HAZ). The porosity area percentage and total solidification crack length in the fusion zone (FZ) were reduced as the welding speed increased from 4 to 7 m/min, Fusion zone area, total penetration depth, and weld width decreased with increased welding speed, The hardness in the FZ was similar to or higher than the base metal after a natural aging of about one year, but there was a drop in the hardness of the HAZ, The HAZ width decreased with increasing the welding speed, Tensile test showed that a joint efficiency of approximately 75 ? 90 % was obtained.

Jan 1, 2005

By V. P. Mehrotra, D. W. Fuerstenau, A. -Z. M. Abouzeid

The use of pulverized coal for electric power generation results in the production of vast amounts of fly ash. One potential use for waste fly ash is the production of pellets for lightweight aggregates. This paper is concerned with the role of the physical and chemical characteristics of two different fly ashes in governing their agglomeration or pelletization behavior and their strength characteristics. In batch balling experiments, fly ash pellet growth was found to be extremely sensitive to the amount of moisture added. One ash (Mohave) exhibits marked pozzolanic activity whereas the other (Jim Bridger) does not. The pozzolanic activity has a very pronounced effect on pellet growth kinetics, moisture requirements, and the effect of various additives on growth kinetics. Slow drying under ambient conditions produces strong pellets from Mohave ash whereas Jim Bridger ash pellets lacking in pozzolanic activity are weak. Rapid drying at high temperatures results in weak pellets because water necessary for hardening is driven out of the pellet. Steam curing enhances pellet strength. Locked-cycle pelletizing experiments exhibit expected oscillation in pellet production rates and attendant fluctuations in pellet green strength.

Jan 1, 2004

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By Osvaldo A. Bascur

Business Challenges ? Many Versions of the Truth ? Lack of Enterprise Visibility (Transparency) ? Limited Communication & Collaboration ? Complex Implementation & Maintenance of software ? End user ease of use of information applications ? Responsive to change ? Access to timely information ? Secure computing ? Maturing Workforce Real time Portal - First of All ? Why Move to a Portal - Portals Recaptures the Business User - Broader Scope - Easy Navigation, World Standard - Features of a Portal - User Profile - Delegation (Secure Delegation of Admin Authority e.g. portal\pat) - Single Sign-On ? HUGE

May 1, 2004

By T. R. Carter, A. C. Colvine

"Rocks of the Grenville Province in southeastern Ontario are currently largely dismissed by many geologists as having little or no potential for discovery of significant deposits of metallic minerals. The present study demonstrates that the area contains numerous deposit types which elsewhere are major metal producers. Therefore, there is significant unrealized potential, especially for gold, zinc, uranium, and possibly copper.The variety of deposits of metallic mineralization include stratiform zinc in marbles; stratabound base metal sulphides in volcanic and sedimentary hosts; gold-quartz veins; quartzmagnetite iron formation; copper-nickel and iron-titanium in intrusive rocks; magnetite skarns; molybdenum in skarns and pegmatites; uranium and thorium in pegmatites, veins, and calc-silicate gneisses; hematite veins; dolomite marbles (magnesium); and barite-jluorite-celestite-galena-calcite veins. There has been significant production of iron, lead, zinc, magnesium, gold, silver, and uranium.The vast majority of the metallic mineral deposits are confined to late Precambrian supracrustal and related intrusive rocks of the Grenville Supergroup. Many of the deposits are stratiform and/or stratabound and occur within units toward the top of major volcanic successions and in the lower portions of younger carbonate-clastic sedimentary successions.Processes responsible for mineral concentration in the area include: (I) syngenetic hydrothermal activity related to both volcanism and sedimentation; (2) epigenetic processes related to diagenesis, regional metamorphism, and igneous intrusive activity; (3) magmatic processes related to igneous intrusions; and (4) supergene concentration and enrichment. The genetic classification of the mineral deposits presented is based on observed geological relationships and these interpreted geneses. The deposit types have counterparts in volcanogenic and sedimentary exhalative, Mississippi Valley type, magmatic, contact metasomatic, and lode gold deposits. Many of the exploration criteria for deposits of these types may be applicable in the Grenville Province, despite the generally high metamorphic grades and complex deformation."

Jan 1, 1985

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By John De La Vergne, Morri Medd

"This paper describes the sinking of a circular concrete ventilation shaft through 110feet of water-bearing overburden. The brine circulation freezing method was used to stabilize the walls during excavation. In order to take advantage of the cold winter weather, a custom-built heat exchanger (natural radiator) was installed in place of the standard mechanical refrigeration plant.IntroductionIn the late fall of 1979, Les Mines Selbaie awarded a contract to the firm of 1.S. Redpath Limited to sink a ventilation shaft on its property in northwestern Quebec. The shaft was to be sunk through 110 feet of water-bearing overburden and approximately 90 feet of rock to a final depth of 200 feet below surface. The water table was measured at 16 feet below the surface elevation.After examining the soils report and diamond drill core from the shaft area, Redpath came to the conclusion that freezing was the best way to stabilize the overburden for sinking. LocationThe mine site is 420 statute miles due north of Toronto, just east of the Ontario/Quebec border (Fig. 1). Access to the site is provided by a development road built by the Quebec government from the Matagami/lames Bay Highway. History of Ground Freezing In the Mining IndustryIn 1862, shortly after the development of mechanical refrigeration, a mine shaft was sunk through an artificially frozen water-bearing formation in the United Kingdom. The first application of ground freezing in North America was for a Michigan iron ore shaft in 1888. Since that time, the freezing method has been used to sink hundreds of shafts throughout the world. Its best known application was to sink sixteen shafts through the Blairmore Formation in Saskatchewan.The same method has been used in every case. It involves chilling a calcium chloride brine solution and circulating the brine in concentric pipes, spaced between 3 and 6 feet around the shaft perimeter and usually 4 to 5 feet from the limits of the proposed shaft excavation."

Jan 1, 1982

By Thomas Kilpatrick

The liability created by building this railway is the great financial problem before the people of British Columbia at the present time. In dealing with the subject, I propose to divide it into three periods: The Past - The Present - and The Future. The Past The primary objects in building the railway were to provide an independent and direct route for the Grand Trunk Pacific railway into the city of Vancouver, and to open the central and north-eastern portion of the province.. This vast territory, almost one-half the entire area of British Columbia, has great wealth in fruit, agricultural, and grazing lands; timber, coal, water-power and minerals of all kinds, including some of the richest placer deposits in the world. Rivers and lakes teem with fish. Big game, including moose, elk, caribou, deer, grizzly and black bear, mountain goat and sheep, is plentiful and there is an abundance of small game and fur-bearing animals. In addition, its scenic attractions are unsurpassed in Canada. To develop these resources it was considered necessary to build a railway from south to north as a main artery of transportation and, if necessary, branch lines to carry heavy .shipments of coal or other commodities. Lighter freight may be handled by motor trucks from distant points to the railway.

Jan 1, 1925

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By K. Hanumantha Rao, A. Javadi

Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Boliden concentrator in Sweden but with the addition of i) collector and depressant, ii) Na2S reductant and iii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid. H2O2 is also found to be a better oxidant in chalcopyrite-galena flotation separation than the commonly used K2Cr2O7.

Jan 1, 2016

By Schoeman L., K. C. Sole

Evaluation and measurement of the influence of changes in conditions and electrolyte composition during early stages of a growing metal electrodeposit are crucial to predict changes in developing morphology. A galvanodynamic polarization technique was developed to reliably measure overpotentials for nickel electrodeposition from sulfate electrolyte. The validity of these polarization parameters as indicators of the relationships between changes in the electrolyte and resulting deposit morphology was evaluated for electrolytes of varying composition. Findings indicate that nucleation and plating overpotentials measured by the described technique can be used as indicative tools for monitoring, evaluating and ultimately improving control of the electrodeposition of nickel from sulfate electrolytes. The results predict that nickel deposits of desirable quality and morphology are obtained when plating overpotentials are higher than 700 mV vs. Ag/AgCl and nucleation overpotential is less negative than plating overpotential.

Jan 1, 2017

By Kevin B. Doyle

"Canada now supplies 23 per cent of the world demand for potash. Although potash is produced by many countries, Russia and Canada have the greatest reserves and capability to supply the future substantial demand over the next decade. It is estimated that demand will grow from 38,000,000 mt KCl in 1975-76 to 60,000,000 mt KCl in 1985-86. Current firm expansion plans and development underway in the world will move Russia to the forefront in supplying this demand growth. Russia will move from supplying 40 per cent of world demand in 1975 to supplying as much as 52 per cent in 1981. Canadian deposits suffer from natural disadvantages, such as high costs and risks of mine development and operation, and high-cost transportation to international markets, but experience has shown that these natural barriers can be surmounted to effectively compete in these international markets. However, Canadian potash is losing out in the race to supply the growth in the world potash demand over the next ten years because of artificial barriers raised through the unhealthy environment created by the current battle between different levels of government and the industry over resource taxation and legislation."

Jan 1, 1976

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd's Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

By Niraj Bala

Boiler tubes of coal-fired boilers suffer severe erosion-corrosion (E-C). One method to counteract this problem is by the use of therma, spray protective coatings. Cold spray coating process was used to deposit Ni-20Cr powder on SA 516 (Grade 70) boiler steel. The bare as wel, as the coated steels were subjected to cyclic experimenta, studies, in the superheater zone of a coa, fired boiler. The weight change technique was used to establish kinetics of the erosion-corrosion. XRD, FE-SEM/EDS and X-ray mapping techniques were used to analyse the as-sprayed and corroded specimens.

Jan 1, 2010

By L. Telfer

Summary During Palaeozoic time, there were deposited in the Canadian Rockies four beds of phosphate rock, ranging in age from Mississippian to Jurassic. Two of these beds are of probable economic importance if some means of separating the phosphate from the gangue can be devised. All the more important beds of phosphate rock so far discovered are just behind the front ranges of the Rocky mountains, within fifty miles of the prairie lands of Alberta. Mining conditions are favourable, with an abundance of timber and ample power available. The phosphate beds are all of the sedimentary type, and they all occur, apparently, at the same stratigraphic horizons over a wide area. The conditions necessary for deposition evidently occurred at several different periods in geological time, and were widespread. The most important factor appears to have been the condition of the land surface surrounding the basin of de-position. Both oolitic and nodular phosphate were laid down under nearly similar conditions. Introduction Following the discovery of phosphate rock in Idaho and Montana, search was commenced in Canada to determine whether formations of similar age in the Canadian Rockies carried similar beds of phosphate. The most widespread search has been that undertaken by the mines department of the Consolidated Mining and Smelting Company of Canada. The following paper will discuss some of the results of this exploration.

Jan 1, 1933

By A. Hussain

PAPER NOT SUBMITTED FOR PUBLICATION

Jan 1, 1987

By Sylvie Lévesque, Cory Hennessey, Daniel Amariei

"In the iron ore industry, fine particles recovery is an important concern in terms of process performance and production costs. Continuous efforts are thus devoted to increase the efficiency in handling these fines.The Reflux Classifier (RC) is a relatively new technology that is mainly used in the coal and industrial minerals industries. The operating principle of this system is based on three mechanisms: hindered settling, autogenous dense medium and lamella settling. A preliminary evaluation of the Reflux Classifier technology for the beneficiation of iron ore fines was formerly done at the pilot scale using a RCTM300 unit. The good results obtained, using iron ore fines from screened spiral stream, made this technology very attractive for the iron industry. However, the high capacity of the RCTM300 unit (1–3 t/h), makes it unsuitable for R&D purposes. Thus, a smaller unit, the RCTM100, was assessed to validate the performances obtained with the RCTM300.This paper summarizes the performances obtained with the RCTM100. The challenges of the scale-down related to the adaptability of this technology to the iron ore industry are also presented. The results are compared to the RCTM300 performances, as well as benchmarked against sink-float tests. The metallurgical results on feed and products issued after the test work with the RCTM100 unit are supported by mineralogical characterization using a Mineral Liberation Analyzer.INTRODUCTIONFine particles recovery by physical separation means is a historical concern (Holland-Batt, 1992; Peukert and Wadenpohl, 2001; Srivastavaa et al., 2001; Majumder et al., 2003). Attempts to improve fine particle recovery at the laboratory, pilot and industrial scales adopting different strategies with traditional equipment or assessing new promising devices such as the MGS (multi-gravity separator), the Kelsey jig, the Yang jig, etc. (Kim, 2002; Goudreau, 2008; Kerr, 2012) have yielded variable success."

Jan 1, 2016

By E. J. Wade

The general location, climatic conditions and access of the Tasu mine are covered briefly, with comments on the Jack of conventional transportation and communication facilities. The Haïda story of Tasu and early at-tempts at production are presented, together with a discussion of the government legislation which throttled exploration and production in the late fifties. General and specific details of local geology, mineralogy and current ore reserves are also covered.

Jan 1, 1968

By R. J. Mitchell

"High narrow backfills of significant strike length approach the stress conditions associated with a free standing wall but this lower bound design approach is not considered efficient for earth structures. This paper considers the design of high narrow backfills using upper bound limit analysis, retaining wall theory with backfill arching and centrifuge model tests. Complex toe support situations pertaining to operational factors at Falconbridge's Lockerby Mine are investigated. It is shown that the susceptibility of high narrow fills to toppling is much lower than anticipated from the retaining wall analysis and that toppling can be avoided by a suitable toe support. It is also concluded that adhesion between the fill and an adjacent pillar can markedly increase the stability of the fill. INTRODUCTIONFalconbridge's Lockerby Mine pillar projects will expose cemented tailings backfills to heights (H) up to 55 m. The exposed backfills may have strike lengths (L) greater than the heights but are relatively narrow, having widths (w) of up to 12 m. The bulk cement content of the fills varies from 8.3% (12.1 T:C) to 3.0% (33.1 T:C). Exposed faces may have up to a metre of overhang due to stope overblasting, as shown in Figure 1. These fills have a solids specific gravity of close to 3.0 and were placed at a pulp density of about 68%. The tailings have a fairly uniform grain size with 32% less than 0.075 mm (200 sieve) and about 12% slimes (less than 0.02 mm sizes). The fill exposed by early pillar removal will be backed by adjacent, near vertical, ore pillars. Future pillar removal may expose similar fills which are not supported by an adjacent ore pillar but which will be backed by either an open void or by uncemented backfill. Furthermore, these fills may be undercut when the pillar slot is driven, further reducing stability (case 3, Fig. I) or a wedge could be left to help support the fill (case 2, Fig . 1). This paper presents limit equilibrium analyses for these various backfill conditions in a 22: 1 T:C fill and com- pares the results to data from centrifuge model studies at a scale factor of A= 157 as indicated in Figure I. Prototype fills have a 6 m deep cone plug of 16:1 T:C which is accounted for in the comparison of centrifuge model test with analytical results."

Jan 1, 1989

By William Skinner, Jim Pae Lem, Massimiano Zanin

It is well known that the specific density of minerals has adverse influence on the classification performance of a hydrocyclone, particularly when liberated high density minerals such as gold or uranium are present in sulphide ores. These liberated heavy minerals often misreport to the underflow and recirculate to the system. Such phenomena does result in serious issues in a closed-grinding circuit, such as overgrinding, leading to production of flaky particles (as in gold) or ultrafines, in addition to increased energy inefficiency. In plants which present gold liberated at coarser size, loss of gold due to cyclone inefficiency is sometimes prevented by incorporating gravity concentrators into the grinding circuit to recover the gold. The work reported in this paper looks at whether the effect of density will prevent successful rejection of liberated U-bearing minerals in the –10µm size range of a plant re-cleaner feed, which is necessary to minimize penalty U accumulation in a copper concentrator. The study was carried out using a cyclone rig with spigot diameter of 0.25 inches in combination with batch flotation. It was found that the density effect is almost negligible at particle sizes below 10µm. Consequently, the liberated U-bearing particles finer than 10 µm were successfully removed in the overflow stream as rejects and hence U grade in the copper concentrate remarkably reduced, by 16 ppm. Based on the results, de-sliming of the re-cleaner feed was recommended for plant trial and implementation.

Jan 1, 2016