Search Documents

By J. L. Bray

LEAD has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-clipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solu-tions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coating medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products are being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating-that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion.

Jan 1, 1937

By Henry Rawdon

THE METHOD of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallographists. The usual procedure1,2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas. (chlorine, hydrochloric acid or similar gas) for. a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced' by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being ad-mitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo.

Jan 2, 1920

By Stephen Taber

Introduction.............................. 62 Asbestiform Minerals.......................... 63 Chemical and Mineralogical Relations............... 63 Physical Properties........................ 64 Types of Asbestos............................ 65 Origin of the Fibrous Structure...................... 66 Views of Previous Investigators.................... 66 Discussion of the Evidence.................... 67 Conclusions........................... 69 Origin of Cross-fiber Veins....................... 71 Chrysotile Veins......................... 72 Structural Features of Cross-fiber Veins............... 78 Veins of Crocidolite and Other Fibrous Amphiboles........... 83 Origin of Slip-fiber........................... 84 Origin of Mass-fiber........................... 86 Discussion............................... 87 IntRoduCtion The term asbestos, as commonly used, includes half a dozen minerals all having a well-developed fibrous structure, but differing in chemical composition and in some of their physical properties. In its strict application the name is limited to the fibrous varieties of the monoclinic amphiboles. Commercially, however, the most important of the asbestiform minerals is chrysotile, a fibrous variety of serpentine. About 95 per cent. of the asbestos used in manufacturing is chrysotile, and it commands a much higher price than any of the other fibrous minerals now on the market. Although the production of asbestos has increased rapidly in recent years, comparatively little has been published concerning its origin. The present paper is preliminary in its nature, and therefore does not pretend to exhaust the subject. The ideas herein developed are the result of field investigation, laboratory experiments in the growth of fibrous

Jan 1, 1918

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of' slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.? Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation ;2,3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942

By Chas. H. Behre, Arbiter. Nathaniel

Two outstanding factors characterize most undertakings in the mineral industries: (1) mineral deposits are not equally distributed over the earth but are localized by natural processes, and (2) the mineral industries are largely based upon wasting assets. Neither of these factors is invariably true, for a few mineral materials, such as water, are essentially world-wide and others are replaced periodically by processes not unlike crop production. Indeed, with some, such as the salts in the sea, the supply is cyclic in short or long periods, whereas others, like water, though locally or periodically in short supply, are essentially inexhaustible. But to the extent that most minerals are limited to certain areas and are "permanently" consumed, any industry founded upon them, by implication, demands great care in planning for the most effective extraction-the essence of wise and conservative expenditure. Several less unusual yet also truly fundamental factors in the economics of the mineral industry are those involving (1) the various kinds and properties of mineral materials, which influence their use; (2) their geo- logic and geographic availability; and (3) the techniques unique to their discovery, exploration, and utilization. This chapter is designed primarily as a brief background for later ones and as a summary of the several un- usual or at least special factors and of their effect upon the economics of the mineral industry. The social and political and especially the economic aspects of the industry are the main subjects of this volume and are dealt with in extended fashion in subsequent chapters. Fundamental Characteristics of Mineral Deposits DEFINITIONS Minerals are naturally occurring compounds of nonliving matter, each technically defined as having (1) a chemical composition that may vary

Jan 1, 1959

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.' In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.' Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By Charles S. Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metallography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method of compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform without fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orientations resulting from recrystallization and is being extended to other metals and other types of deformation. PREVIOUS WORK The previous experiments are few and have given confusing results. Ono1 compressed a polycrystalline alpha-iron specimen between two flat plates of a testing machine and found that severe deformation oriented the crystals into a duplex preferred orientation, one set of crystallites having a cube diagonal of the body-centered cubic lattice parallel to the compression axis, and another set having a cube axis parallel to the compression axis. We shall speak of this structure as a. double fiber texture of the type [111] + [100]. Wever2 also made an X-ray determination of the texture

Jan 1, 1938

By R. D. Russell, R. M. Farquhar

SOTOPIC tracers have become an important aid in following the progress of chemical processes in the laboratory. It has recently been found possible to utilize a system of naturally existing iso-topic tracers to obtain information about the geological history of lead ores. Common lead, such as is found in lead deposits, is a mixture of four stable isotopes having atomic weights 204, 206, 207, and 208. Of these, the last three are identical with the lead isotopes produced as stable end products of the radioactive decays of uranium and thorium: the first, lead-204, is not known to be produced on the surface of the earth by any process. Since uranium and thorium Occur in the surface regions of the earth in amounts comparable with lead, and since the half-lives of uranium and thorium isotopes are of the same order as the age of the earth, they produce the radiogenic lead isotopes in amounts comparable to the amount of nonradiogenic lead present. Every significant exposure of a sample of lead to uranium and thorium will therefore lead to the permanent alteration of the lead isotope ratios in that sample. It is this unique property of lead that serves as a means of tracing the history of a lead sample in terms of its contacts with the radioactive elements. If lead from a lead mineral has been analyzed with a mass spectrometer, the measured isotope ratios are determined entirely by the isotope ratios of primeval lead, which are identical for all minerals, and by the particular history of the sample. It follows that for samples from any particular geological area, observed differences in the isotopic composition are enough to distinguish different geological histories. An illustration of the qualitative application of this statement is given in Table I by analyses of some galenas from the western Cordillera. Samples from deposits in Pre-Cambrian sediments have very different lead isotope ratios from those of the ores in the Paleozoic sediments. Although the two types are associated closely geographically, it is apparent that they have had quite different histories and have probably been emplaced at quite different times, as the ideas outlined in the following section suggest. Even when applied quantitatively, a lead isotope analysis can never indicate a unique history of any lead sample. However, it greatly restricts the choices available and combined with other geological and geochemical data can lead to a much better understanding of the genesis of lead ores. General Character of Lead Isotope Variations: Early isotopic analyses of common leads by Nierl showed that geologically younger leads were generally richer in isotopes of masses 206, 207, and 208, with respect to that of mass 204. This regularity of measured lead isotope ratios can be easily observed by plotting each of the ratios Pb207/Pbm and Pb205/ Pb204 against the ratio Pb206/Pb204. In both graphs the points lie scattered closely about a well defined mean curve. It was immediately supposed that this regularity resulted from the growth of all leads from a common primeval lead present at some time, To, early in the earth's history. Lead in the outer part of the earth would become continually enriched in the radiogenic isotopes as a result of the uranium and thorium intimately associated with it. The subsequent extraction of some of this lead and formation of a lead mineral free of the radioactive parents provide samples of lead existing in the earth at the time of mineralization, T. Younger leads in general will be richer in the radiogenic isotopes because they have been associated with uranium and thorium for a longer time. Then lead ratios would be given by the formulae: (Pb206/Pb204)YTPb^/Pb204) +f "(u201) kdt T (Pb207Pb204)r = (Pb208/Pb204)T0 + J (U295/Pb204) k' dt T (Pb208/Pb204) t = (Pb208Pb204 + J (Th204) A." dt [1] where A, A', and A" are the decay constants of U238, U285 and Th232. Summaries of measurements of radioactivity of surface rocks, such as given by Faul,2 are of limited

Jan 1, 1958

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell' (Table 1).

Jan 1, 1934

By John Chipman, Carl F. Floe

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Carl F. Floe, John Chipman

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

By Robert L. Llewellyn

Preparation of coal begins at the face in underground mines or in the pit with surface mines. Impurities in raw coal can be in the seam itself or in extraneous material taken in mining from the roof or bottom. Raw coal is prepared only to the extent that is necessary to make the product salable. Over 60% of all coal production is processed to some extent in cleaning plants. For underground mines the proportion cleaned is 72% as compared to 42% from surface and 15% from auger mines. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only as necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent and only incidently with mines shipping raw run-of-mine coal crushed to a top size of, usually, 2 to 4 in., with little, if any, other treatment. ECONOMICS OF COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-rang planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and atomic energy. Cod prices for power plants are still on a Btu (British thermal unit) basis but with more emphasis on sulfur content. For metallurgical coal, the lower and medium volatile coals are in demand and the price rises, generally, as the volatile percentage is lower. Moisture affects the Btu value of coal almost the same as ash content, but dusty conditions during loading and unloading are no longer accept-

Jan 1, 1973

By J. D. Embury, R. M. Fisher, A. S. Keh

An investigation of the defect structure and properties following large strain deformation has been carried out using transmission electron microscopy and mechanical testing for a range of ferrous materials and for copper. It is shown that, for a variety of ferrous materials, a cellular substructure is developed during the initial stages of working and on further deformation the dimensions of this substructure are reduced. Quantitative measurements of the flow stress and the scale of the substructure indicate that the strength of heavily worked materials is largely determined by the spacing of cell walls. These cell walls act as dislocation barriers in a manner analogous to grain boundaries. FCC materials do not harden as extensively as bcc after cold working and the present observations on copper indicate that the dimensions of the substructure in fcc materials are not markedly reduced on deformation. The differences between the fcc and bcc structures produced by large plastic strains are ascribed to differences in the extent of dynamic recovery. It is tentatively proposed that the greater stability of substructural barriers in bcc structures results from strong interstitial Pinning effects. It is proposed that for large plastic strains the work-hardening process may be considered in terms of the reduction of substructural-barrier spacing during the working process. This pvovides a simplified hut useful analysis of the strain hardening occurring during mechanical processes. THE mechanisms of strain-hardening processes have occupied the attention of numerous investigators over the past three decades and a multitude of theories have emerged in this field. The majority of previous work has been concerned with the development of a description of the plastic behavior of single crystals in terms of dislocation theory.'" In contrast, scant attention has been given to the strengthening mechanisms operative during mechanical working processes such as rolling and drawing. The large plastic strains involved in these processes make it difficult to correlate the observations with any elementary dislocation theory. Further, as Bullen and coworkers3 have opined, for large plastic strains both hardening and recovery occur simultaneously and thus it is extremely difficult to estimate the effect of plastic strain on the ambient internal stress field. It is probable that for large plas- tic strains any theoretical estimate of the internal stress field must be made in terms of complex dislocation groups. Although some valuable theoretical work has been done toward calculating the elastic properties of dislocation groups4 any detailed self-consistent model for large plastic strain is as yet impossible. With these limitations in view it is still of value to examine the mechanical properties of highly strained materials as a function of their substructure. This relationship is explored in the present communication for a variety of materials subjected to rolling, drawing, or swaging. The primary object of this investigation has been to establish the validity and the limitations of the substructural strengthening mechanism proposed by Embury and eisher' for drawn pearlitic wire and by Meieran and Thomas for drawn tungsten wire. No attempt has been made to delineate the basic interaction mechanism which occurs between a slip dislocation and the substructure and the authors believe that a great deal more experimental evidence must be compiled before these fundamental aspects can be explored. Also, no specific attention has been given to the detailed formation of substructure during working. Experimental Details. A variety of materials were used in this investigation, the compositions and heat treatment of which are tabulated in Table I. The commercially pure iron is referred to throughout this report as Ferrovac E. The mechanical working processes were all performed at room temperature. The wire drawing was performed on a manual drawing bench. Reductions of between 10 and 20 pct in area per pass were used in both swaging and drawing. The experimental parameter used to evaluate the mechanical properties of the materials was the 0.2 pct proof stress. This was determined for wire samples using an Instron tensile machine at a crosshead speed of 0.02 in. per min. The techniques for preparation of samples for transmission electron microscopy have been described previo~sl~.~ Specimens from wire samples were prepared from longitudinal sections and in some cases from transverse sections. To evaluate the substructural characteristics of rolled materials, thin foil samples were prepared of both the face and edge sections. Results. One of the more familiar ways of expressing work hardening in mechanical working is by the flow stress as a function of reduction in cross-sectional area. Fig. 1 shows such a plot for Ferrovac E eutectoid carbon steel and for copper. The curve for Ferrovac E is characterized by an initial stage of rapid work hardening and a final stage of rapid work hardening separated by an intermediate stage with a low rate of work hardening. This behavior is typical of many ferrous materials and the drawn pearlite wire previously investigated by Embury and Fisher is a more pronounced example. Copper shows an initial

Jan 1, 1967

By Ellis Clark

THE mining town of Pribram is situated in Central Bohemia, on the western slope of the Heiliger Berg, 30 miles southwest from Prague. Birkenberg, the village in which most of the shafts and ore-dressing establishments are situated, is built on a mountain of the same name. It is about a mile from Pribram, is 1700 feet above the sea, and is surrounded by graywacke rocks of Silurian origin, which are intersected by greenstone dikes, and in the southerly, southeasterly, and southwesterly direction are bounded by granite. The graywacke formations consist on one side of graywacke sandstone and quartzite, and on the other of graywacke slates. These last are separated from the first in the immediate vicinity of the mines by a graywacke seam converted into clay. For many years this so-cal led clay seam (lettenkkluft) was considered as a boundary of the ore deposits in both zones of graywacke. The graywacke formation is divided according to its hardness, structure, texture, and color, into fine, coarse, compact, slaty, whitish-gray, reddish-gray, and black graywacke. The, miner divides the formation into four divisions. The first or lowest division, which is in contact with the granite, consists of a fine-grained dirty gray slate; the -second is a very fine to a very coarse schist, white to reddish-gray in color, and rich in quartz, but containing little mica; the third consists of a slate with a contused cleavage, which has a dirty gray, dark gray, and very often black color and is often graphitic in its composition ; the fourth consists of a fine to coarse-grained graywacke schist, of a grayish-white or reddish-gray color, and rich in quartz. The cleavage in all four divisions strikes from northeast to southwest, and the dip is sometimes northwesterly, sometimes southerly, and often vertical. All four zones are cut through by a great number of diorite and greenstone dikes and chimneys. The thickness of these dikes, which are of

Jan 1, 1881

By Robert Mehl

METALLURGISTS are properly interested in papers dealing with subjects ranging from the theories of the metallic state to very practical details on the use of metals. A review of theoretical metallurgy naturally excludes papers concerned with the usefulness of metals and limits itself to those concerned purely with the science of metals. Even in this more limited field the reviewer is confronted with thousands of papers dealing with facts and theories of metallic behavior, from which he can select only a few hundred. The selection is necessarily highly arbitrary. Certain classes of papers definitely fall within the scope of this review. Thus, papers on the deformation of metals, on the structure of alloys, on recrystallization, to select only a few, are fully represented. Other subjects, which verge on what is generally accepted as the science of metals, such as the magnetic properties of metals, the less familiar electrical properties and theories, adsorption of gases by metal surfaces, and the like, are treated scantily. Particular attention is given to reviews of subjects that fall with in the groups chosen; in a summary such as this, which is largely in the nature of a progress report, capably written reviews are of importance, particularly since the monograph and text book literature is so meager in this field.

Jan 1, 1935

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By S. W. Miller

Most of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,' that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., he has since found large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than % in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top 1/16 in (1-5 mm.) of the weld, they were removed by the grinding or machining; also, welds 3/4 in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was decided to find where the rupture occurred in various kinds of welds made

Jan 1, 1920

By C. E. Lesher

Low-temPeRatUre carbonization needs no introduction to the literature on coal. This paper will attempt no review of that literature; it tells the story of the commercial development of one of the processes for carbonizing coal at so-called low temperatures, dealing with the technology and economics of the process rather than with the design of equipment. The process used is that covered by the patents of C. B. Wisner, with improvements and changes made by the Pittsburgh Coal Carbonization Co. The important and novel feature of the process is the phenomenon of making the product in ball form (Fig. 1). Melting coal dust into smokeless solid fuel in an apparatus as simple as a revolving cylinder of ordinary mild steel has been proved to be practical. Furthermore, it has been found that the process has a wide application, for by applying a knowledge of why and how this balling action is accomplished, the apparatus can be designed and adapted to treat any coal that has a certain minimum agglutinating property. The operating plant is 20 miles west of Pittsburgh, adjacent to the Champion preparation plant of the Pittsburgh Coal Co. The coal used is cleaned minus ?-in. or finer sizes. The products are low-tem-perature coke, tar and tar products. Present capacity is 7000 tons per month of low-temperature coke and 140,000 gal. of tar. There is no surplus gas for sale, and none of the light oils are stripped from the gas. The coke is marketed in two sizes, 1 to 2 in. and 1 to 6 in., through retail coal dealers for domestic consumption in hand-fired furnaces, and for fireplace fuel. The smaller size is bagged by dealers. Crude tar and many distillates and road tars are sold. Acknowledgments During the 10 years in which the work that is summarized in this paper has been under way, many have contributed time and effort, faithful service and fruitful thinking. Whatever success has attended

Jan 1, 1940