Search Documents

By Robert F. Mehl

EXTENSION of physical and chemical methods of research in the study of metallic behavior continues rapidly, particularly in the correlation of behavior with crystal structure, and in the analysis of elastic and plastic properties. The growth of the science of metals during 1933 calls for special comment; the need for special reviews and for textbooks and monographs is now acute, as might he supposed from the number of references appended to this article, a list which is much abbreviated.

Jan 1, 1934

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By S. Nenno, T. Saburi, Y. Mizutani, M. Yomarnoto, K. Komatsu

In the equilibrium phase diagram of the Ni-Mo sys-tem1,2 available at present, intermetallic compounds (or ordered phases)ß(Ni4Mo) and ?(Ni3Mo) are known to exist to the nickel rich side. In our recent investigations on Ni-Mo alloys, however, it has been found that the quenched alloys from the high temperature region containing more molybdenum than the Ni4Mo do not decompose directly into 0 and when annealed isothermally below the peritectoid temperature, i.e., 865°C. This note is to report the existence of Pt2Mo type superlattice (possibly ordered Ni2Mo) as a metastable phase in the early stage of decomposition. Alloys containing 20.1, 22.7, and 24.4 at. pct Mo were prepared by vacuum-melting electrolytic nickel of 99.9 pct purity and molybdenum powder of 99.9 pct purity in an alumina crucible. From the resulting ingots, sheets 0.3 mm thick were obtained by forging, hot-, and cold-rolling. The sheet specimens were water-quenched from ! region and subsequently annealed for various periods of time at temperatures below the peritectoid temperature. On these specimens were made optical-microscopic and transmis-sion-electron-microscopic observations. Fig. 1- Optical micrograph of the 22.7 at. pct Mo specimen annealed for 100 hr at 700°C after quenching. (ß + ?) region, B, nucleated along a grain boundaries are invading the preexisting (ß + Ni2Mo) region, A. Details of A are observable only by electron microscopy. Etchant: 60 pct HNO3-40 pct CH3COOH.

Jan 1, 1970

By John T. Thorndyke

MOST important of the naturalcalcium silicates is the meta¬silicate, CaSi03, known as wollastonite, after W. H. Wollaston. A large deposit of this mineral was dis¬covered some seven years ago near Code Siding, Rademacher mining dis¬trict, Kern County, Calif., the deposit being some 7500 ft. long and of an average width of 300 ft. It consists of a series of small domes striking north¬erly and southerly and with a dip of 81 ° to the south. This deposit was opened up by a series of small quarries showing a potential tonnage of 12,000,¬000 tons, allowing of cheap mining and transportation, the Southern Pa¬cific R.R. spur track being one mile north of the workings. Numerous sam¬ples taken from different points on the deposit, tested by Mr. Brinker, of the California Testing Laboratories, Los Angeles, showed an average as fol¬lows: Per Cent Silica (SiO2) 47.12 Lime (CaO) 41.72 Magnesia (MgO) 2.72 Alkalies (R,0) Trace Iron (Fe.,O,) 1.60 whereas the theoretical composition of of wollastonite, as given by William Shirley Bayley, is as follows: Silica 51.75 Lime 45.25 The tonnage and purity of this de¬posit led to investigations into its com¬mercial development. Early work es¬tablished the fact that wollastonite was ideal for the manufacture of a tough, almost unbreakable, glass similar to Pyrex. It also established the fact that wollastonite was particularly adapted for use in the manufacture of mineral wool, towards which further research was then directed. Briefly, the prin¬cipal advantages were the substantially unvarying chemical composition of the naturally occurring mineral and its characteristic of being relatively flexi¬ble and highly resilient when fused into a glass. A mineral wool produced therefrom is thus not only of highly uniform composition and color but is most desirable because of the high mechanical strength and length of the individual fibers constituting the wool. It is well known that mineral wool may be prepared by melting a suitable charge of raw material and then intro¬ducing a stream of a suitable fluid, such as air or steam, into a stream of the molten raw material. By this means the molten material is blown into threads or fibers, which are collected in a suitable chamber similar to a tun¬nel, from which they are removed from time to time or continuously. Com¬mercial manufacture of mineral wool has been carried on for only about 50 years, but volcanoes, specifically Kilauea in the Hawaiian Islands, have

Jan 1, 1936

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By L. D. Jaffe, D. C. Buffum, F. L. Carr

SINCE the temper brittleness of steels is generally considered to be a grain-boundary phenomenon¹,² it would be expected that austenitic grain size would affect temper brittleness. Several investigators"" reported that temper brittleness, as measured by room-temperature impact tests, increased as the austenitiz-ing temperature was raised. It was subsequently pointed out that conclusions as to temper brittleness based upon room-temperature impact tests are likely to be misleading.1,6 Hurlich7 used a range of testing

Jan 1, 1954

By Frank L. Nason

In the year 1904 an eminent Swedish geologist prepared a report on the iron-ore reserves of the world. His estimates follow: Countries. Tons. United States,.1,100,000,000 Great Britain,.1,000,000,000 Germany,.2,200,000,000 Spain,.. 500,000,000 Russia and Finland,...... 1,500,000,000 France,..1,500,000,000 Sweden,..1,000,000,000 Austria-Hungary,....... 1,000,000,000 Other countries,1,200,000,000 Total,.10,000,000,000 The iron-ore allotted to the United States by the Swedish geologist is barely sufficient to last 20 years at. the present rate of consumption. On the other hand (according to Edwin C. Eckel,&apos; from whom the above and following statistics are quoted), there is hardly need for worry on the part of our iron industries for the next two centuries or more. Upon the basis of careful work by the U. S. Geological Survey, in which Mr. Eckel has taken an important part, the following estimates are definitely, but by no means finally, given for the United States: District. Tons. Lake Superior District,... 1,500,000,000 to 2,000,000,000 f red hematite,.. 1,000,000,000 Alabama, brown hematite, hematite, . 725,000,000 red hematite,.. 200,000,000 Georgia, { brown hematite, . 125,000,000 Tennessee, { red hematite,.. 600,000,000 Tennessee, { brown hematite,hematite, . 225,000,000 f red hematite,.. 50,000,000 Virginia, } brown hematite, . 300,000,000 Total,..4,725,000,000 to 5,225,000,000

Jan 1, 1913

By Harrison Everett Ashley

Prof. Hofman&apos;s diagrams, Figs. 5 and 7 of his paper, which are reproduced as Figs. 1 and 2 of the present contribution, confessedly fail to show comprehensively the properties of the silicates investigated. Each curve is carefully discussed, and the author has evidently drawn all the conclusions that can be thus reached; but he says :* "The curves do not show, as was hoped, any simple connection between silicate-degree, percentage of lime, and minimum of formation-temperature." There is, therefore, in this case, an excellent opportunity of

Jan 1, 1902

By J. Nagy, D. W. Mitchell, E. M. Murphy

In 1957 research was initiated in the U.S. Bureau of Mines experimental coal mine near Pittsburgh, Pa., to study factors affecting foam generation and transport, to evaluate the effectiveness of high-expansion foam for controlling mine fires, and to develop techniques for applying the method under U.S. mining conditions. These investigations showed that high-expansion foam containing at least 0.2 oz of water per cu ft of foam is effective in controlling experimental underground fires burning coal, wood, and oil. Sometimes the fire was completely extinguished, but more often, it was brought under sufficient control to permit either a direct attack on the fire with a stream of water or loading of the hot material into cars. A progress report&apos; prepared in July 1958 summarized the initial achievements of the USBM experiments. Since then other phases of the foam-plug method for attacking fires have been studied in the laboratory and in the mine. Previous studies by British engineers&apos; of the foam-plug method for fighting mine fires indicated that high-expansion foam was effective in controlling experimental timber fires in an underground passageway. Their subsequent workx-1 pertained to the practical aspects of fighting large fires within a mining area with a foam-plug. CONTROLLING EXPERIMENTAL FIRES In the USBM tests foam was formed by spraying a dilute solution of a foaming agent on a metal or cotton net of 1/8 to 1/4-in. mesh. Air passing through the continuously wetted net forms bubbles of 1/2 to 11/2-in. diam and produces a honeycomb of foam that fills the passageway. Under the ventilating-air pressure, this light-weight plug moves forward through the passageways, around sharp corners, and over obstacles. as illustrated in Fig. 1. High-expansion foam was transported to a wood fire, an oil fire, and 13 coal fires. Figs. 3 and 4 show a typical coal fire before and after attack with foam. In 12 of the 15 experiments the fire was brought under control when the water content of foam was 0.2 oz or more per cu ft. A fire was considered controlled when the flames were quenched and observers could cross the area without wearing breathing apparatus or protective clothing. In the other three experiments, conducted when the water content was less than 0.2 oz per cu ft of foam, the flames were retarded but the fire was not controlled. Coal fires have been attacked successfully by foam introduced at points varying from 155 to 1010 ft from the fire. The time of burning in coal beds 10 in. thick ranged from 11/2 to 5 hrs or more. Most of the experimental fire beds were 15 ft in length. However, in one experiment a floor fire 25 ft long and 5 ft wide was constructed $5 upwind from another fire 15 ft in length; in another instance, the fire was 100 ft long and 5 ft wide. Foam was applied to the fires for periods ranging from 7 to 36 min. The time required for foam application depends on the extent of the fire, time of burning, water content of foam, foam velocity, and degree of fire control desired. In addition to the coal fires, foam was transported to a fire covering 45 sq ft, produced by 15 gal of oil burning in metal trays on the floor. The foam extinguished the oil fire in about 1 min. In one other test, the burning of 1100 lb of dry sawmill slabs stacked in open cribs 4 ft high and 16 ft long was brought under control by foam in 2 min. Composition of Gases in Return Air: In several of the experiments samples of the return air from fire zones were collected; composition of the atmosphere before, during, and after foam application was then determined. Because of condensation in the relatively cool sampling tube, the amount of water vapor was not determined. Analyses showed that concentration of carbon dioxide and combustible gases increased as the foam began passing over the fire. This resulted from the decrease in the volume of air when foam generation started and from the formation of gases when water reached the fire.* The quantity of gases generated would not be greater than that from an equivalent amount of water applied directly to the fire. The highest total concentration of combustibles (CO, CH1, and H2 mixture) obtained during the experiment was about 2 pct; this occurred 6 min after foam reached the fire. This atmosphere was nonex-plosive, but calculations show that if the air flow were reduced to about 5 fpm and if the rate of gas liberation from the fire remained constant, the mixture would be explosive. The use of foam on a fire in all probability would affect the normal ventilation of a mine. If the mine is gassy, this factor must be carefully considered before the foam is applied. APPLICATION OF THE FOAM-PLUG TECHNIQUE IN MINES Equipment and procedures for applying the foam-plug methods must be adapted to the prevailing conditions at a particular mine. Some factors to be considered in developing equipment are: size or extent of the mine, dimensions and number of entries, ventilation system, mining methods, haulage facilities, availability of water, amount of methane liberated, and existing fire-control apparatus. • In most experiments the initial air velocity of 200 fpm decreased to 50 to 100 fpm as the foam plug increased In length.

Jan 1, 1961

By Billy L. Crowder, John M. Fairfield

The implantation of B+ , P+, and As&apos; into silicon has been studied with the purpose of making shallow p-n junctions. The influence of such parameters as 1) ion energy, 2) target orientation and temperature, 3) total dose, and 4) annealing schedule was investigated. An energy range of 70 to 300 kev was used for boron and phosphorus implants and up to 500 kev for arsenic. It is found that the experimental projected range agrees well with theory and that shallow junction depths can be made reproducibly. ION implantation has received much attention recently as a technique for doping semiconductors. Specifically, it has the potential of supplementing or replacing the diffusion process as a method for making p-n junctions. In a few specific cases it has been used successfully to make semiconductor junction devices. Potential advantages of ion implantation doping over diffusion techniques are: 1) It affords greater control of shallow junction depths (< 0.2 µ) while maintaining high peak concentrations. This is particularly important for high-speed switching devices, since lower junction capacitances and resistances can be achieved. 2) More precise registration of small planar structures can be realized if proper masking procedures are employed. This advantage is especially useful in the design of high-density integrated circuits. It has been used to advantage in FET fabrication since the edge of the source or drain can be aligned precisely at the edge of the gate electrode.&apos; 3) Ion implanatation permits lower temperatures than diffusion techniques. This factor alleviates the problem of compatibility of diffusivities often encountered when designing multiple-junction structures. Also, the lower temperatures create fewer thermal defects and dislocations, which may account for the high efficiency of some ion-implanted solar cells.2 4) Impurity profiles can be more easily tailored to resemble ideal distributions. Successful exploitation of the potential advantages of ion implantation techniques will depend on increased knowledge and understanding of the subject. The factors likely to be influential in determining impurity distribution profiles in ion-implanted single-crystal targets have been reviewed by J. F. Gibbons.3 In addition to the mass and energy of the implanted ion, the total dose, target orientation, and target temperature are important parameters. The annealing temperature required for removing lattice damage and incorporating the implanted species on an electrically active site is very important. This paper describes an investigation of some of these factors. Implants of boron, phosphorus, and arsenic into silicon have been studied. Energy ranges of 50 to 300 kev were used for boron and phosphorus and up to 500 kev for arsenic. In addition to the implantation energy, the effects of total dose, target temperature, and post implant anneal have been investigated. EXPERIMENTAL PROCEDURE The implantation targets were silicon wafers cut from Czochralski-grown crystals, lapped, and chemically polished. The orientations were (111), (110). and (100) with misorientations of up to 7 deg from the principal axis. For this study, accurate target alignment (i.e., within 0.1 deg) was not available and quoted misorientation values should be regarded as approximate . The implantation equipment consisted of an ion source, a 300-kev linear accelerator tube, an electromagnetic separator, and the associated target supporting and beam focusing assemblies. The ion source was a simple oscillating electron type source,4 which has been described elsewhere.5 The gaseous compounds BF3, PF5, and AsH3 were used as ion sources for B+, P+, As+, and AS+&apos;. Analyzed current levels of up to 20 pamp could be obtained; however, for this investigation target current levels of 1-3 µ amp were usually employed. The analyzed ion beam was collimated through a double slit (1.4 x 0.4 cm) and swept perpendicularly to the long axis of the slit such that an area of about 2 sq cm on each target was covered. Dosages of around 1015 cm-2 were normally employed, but smaller amounts were also used for comparison. A uniform flux density over the bombarded area was assured by the continuous use of profile monitors similar to those described by Wegner and Feigenbaum.6 Post-implant annealing was accomplished in an argon atmosphere in a temperature range of 600" to 950°C. It was not part of the purpose of this investigation to study the annealing kinetics; however, some isochronal and isothermal anneal experiments were conducted to determine the time and temperature necessary to render a reasonably high portion of the implanted ions electrically active (i.e., higher than 50 pct). Post-implant anneal temperatures of around 900° and 600°C were required for boron, and arsenic and phosphorus implants, respectively. Arsenic and phosphorus implants increased in conductivity rather abruptly at the proper anneal temperature of the isochronal curve, but boron increased more gradually over a wider range. Isothermal anneal curves were reasonably flat after 10 min, so an anneal time of 1/2 hr was used for the experimental results described below. The profiling techniques were: 1) neutron activation analysis, 2) differential sheet resistance,7 and 3) junction staining.8 The differential sheet resistance technique is commonly employed in this type of study. Its principal disadvantage is the uncertainty of the ef-

Jan 1, 1970

By G. W. Elger, H. E. Bell, J. E. Tress, J. B. Wright

This paper describes laboratory techniques and subsequent results of US Bureau of Mines (USBM) research to produce chlorination-grade feed- stock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau effort to devise technology that may help decrease US dependence on imported raw materials. A rock ilmenite containing about 46 wt % TiO2 was smelted in an electric arc furnace with coke, wood-chips, and Na2CO3 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slug. The slug was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1-kg/h (10- to 20-lb per hour) apparatus at 1023° to 122J0 K (1380° to 1740° F). The sulfated slug, containing 60% to 65% TiOb, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome calcium, magnesium, and manganese impurities from 7.0 to 1.7 wt 70. The final product was upgraded to about 8.4 wt % TiO2. This material is potentially suitable for chlorination in a fluidized bed reactor. The most favorable results were achieved with leached slug sulfated at a feed rate of 4.5 kg/h (10 lb per hour) and at temperatures of 1073° to 1123° K (1470° to 1560&apos; F).

Jan 1, 1986

By Garth M. Crosby

Seven mines with important production records in the Coeur d&apos;Alene lie adjacent to the Gem stocks -the Frisco (Gem), Hercules, Interstate, Rex (Sixteen to One), Success (Granite), Sunset, and Tamarack. Old records are incomplete, but avail- able data given in Table I show these mines have produced 10,550,721 tons of ore containing more than 50 million oz of silver, more than 1.5 billion lb of lead, and about 1 billion lb of zinc (approximately 1.25 million tons of lead and zinc combined). Average ore grade is 4.8 oz of silver per ton, 7.2 pct Pb, and 4.6 pct Zn. This impressive production represents about 12 pct of the District&apos;s yield. At present metal prices, with modern beneficiation, the gross value would be more than $400 million.

Jan 7, 1959

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300&apos; and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella&apos;s ferric chloride solution for intermediate compositions; and Marble&apos;s (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By L. C. Brown, J. S. Kirkaldy

Measurements have been made of carbon diffuswn in the five ternary austenites Fe-C-Si, Fe-C-Ni, Fe-C-Co, Fe-C-Mn, and Fe-C-Cr in which the carbon (component 1) diffuses through interstitial sites and the ternary addition (component 2) diffuses substitutionally. Values of the diffusion-coefficient ratio, D12/D11 were determined for each system with finite couples using the transient equilibrium method. The effect of temperature and of concentrations of both the carbon and substitutional component upon D12/D was examined and was found to agree with the theoretical predictions. It is concluded that within an experimental uncertainty of 10 to 15 pct, it is possible to calculate the ratio D12/D11 from purely thermody-namic data. Difficulties of measuring the other off-diagonal coefficient, 4,, are discussed. Any quantitative attack on the fundamentals of the hardenability problem in steel must begin with the multicomponent diffusion formalism and with the accumulation of data pertaining thereto. In a recent paper Kirkaldy and purdy 1 employed the formalism derived from irreversible thermodynamics to treat the problem of diffusion in ternary austenites. In the latter solutions, carbon diffuses through interstitial sites and the substitutional component diffuses through the lattice. Examples were given of diffusion in the systems Fe-Mn-C and Fe-Si-C. In the present paper, we present new results on and discuss their agreement with the thermody-namic theory. Since the theory has been slightly modified from the original presentation of Kirkaldy and Purdy, their results on Fe-Si-C and Fe-Mn-C have been recalculated and are presented here for completeness. The flux of the interstitial component with respect to a fixed lattice framework can be written as a linear expansion in the independent concentration gradients, where X1 and X2 are the independent thermody-namic forces in the lattice fixed frame of reference. These forces can be obtained from the general statement for forces in a volume fixed frame2 if the partial molar volume of carbon atoms is set equal to zero and that of the substitutional component 2 is set equal to unity, viz where the are the chemical potentials and the N&apos;s are mole fractions. Introducing into [3] and [4] the function If, as suggested by statistical arguments, the off-diagonal interaction L12 is sufficiently small, [6] reduces to i.e., the coefficient ratio becomes purely thermo-dynamic. The activity of components 1 and 2 in a dilute ternary system (standard state at infinite dilution) may be represented by the expansion3

Jan 1, 1964

By Georges Ranque

THIS paper by. Georges Ranque is an attempt to reason out the conditions of formation and stability of inclusions and to establish an operative process capable of eliminating or minimizing them. The paper consists of two parts; one in which the author considers the laws of physical chemistry and physics that apply to liquid slag-metal systems and one in which he describes a practice based on the theoretical considerations. Such a paper is bound to contain controversial points and it is therefore your speaker&apos;s intention to present Mr. Ranque&apos;s side of the picture to the best of his ability without regard for any thoughts or criticisms of his own. RISING VELOCITIES OF INCLUSIONS Most nonmetallic inclusions have densities ranging from about 1.7 to s, while liquid steel has a density of about 7. Under these conditions, ferrostatic pressure should cause the inclusions, being lighter, to rise from the bath and be eliminated. This rising tendency is expressed by Stokes&apos; law, from which may be calculated the rising velocity of a spherical particle in a liquid medium whose density and viscosity are known.

Jan 1, 1947

By R. S. Sandhu, L. E. Baker, W. Y. Shieh

The finite element method of analysis was introduced by Clough.1 Within a short period, it has developed into a powerful solution technique in structural and continuum mechanics. It has been used to solve boundary value problems in two and three-dimensional elasticity.2-5 Anisotropy and heterogeneity of materials were allowed for at the earliest stages. 1,4 Its application has been extended to allow for cracks,5 creep and viscoelasticity, 6,7 incremental construction,6-8 nonlinear elasticity3,9 effect of joints in rock,10 and to materials with different behavior in tension and compression.7 Because of its versatility, the finite element method has found increasing application in the field of rock mechanics. In fact, several of the more significant developments have been motivated by problems in this field. Elasto-plastic material behavior based on the incremental or rate-type theory of plasticity rather than the deformation theory was considered by Reyes and Deere11 A material law based on a generalization 12 of the Mohr-Coulomb criterion was used. In this chapter, the formulation of material laws developed by Reyes and Deere 11 is used. An efficient analysis procedure, incorporating recent developments in finite element analysis, is developed for plane-strain conditions. To demonstrate its effectiveness, the procedure is applied to three cases, one for which an exact solution is available, another for which field observations had been made, and a third one for which a parallel study was made, using an accepted limit-equilibrium method.

Jan 1, 1970

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962

By C. Feng, C. Elbaum

AN investigation of the fracture plane of titanium, containing 0.5 wt pct to 1 wt pct 0, was recently carried out by fracturing large-grain specimens in a tensile jig at room and liquid air temperature. The experiments were carried out on strip specimens 3 to 5 mm wide, 2 mm thick and about 100 mm long. The specimens consisted of several grains, each occupying the entire cross section of the strip and extending over a length varying from 5 to 20 mm. These specimens were prepared by a method described elsewhere.&apos; The identification of the fracture plane was possible in twelve of approximately thirty crystals investigated. In some cases severe local distortion took place near the fracture and prevented identification of the fracture plane. On, at least, three occasions the fracture propagated in a helicoidal

Jan 1, 1959

By B. Amadei

INTRODUCTION Laboratory studies on the deformability and strength of intact rocks generally involve the uniaxial compression test, the standard triaxial compression test and direct or indirect tension tests. If [al ,a2 ,a3] are principal stresses [(al>a2>a3)] with compression taken as positive and tension taken as negative, the applied stress field for each one of these tests can be represented as shown in Fig. 1. However, for most in-situ conditions, such as those that exist at any point around an underground excavation, the stress field is truly three-dimensional or multiaxial [(al+ a2+a3)] and none of the tests shown in Fig. 1 can be used to predict the mechanical behavior of the rock. There are special cases for which one of the three principal stresses vanishes. Biaxial loading of rocks in-situ takes place, for instance, when rocks deform and fail in plane stress conditions. This can occur in a free unloaded surface of a rock structure such as in the wall of an underground excavation or a rock slope. Parallel to the free surface, the stress field components can be both compressive [(al>a2>0)], both tensile [(O>a2>a3)], or mixed, one component being compressive and the other one tensile [(U~>O>U~)]. The purpose of this paper is to present the results of 25 true biaxial tests that have been conducted on cubical specimens of Indiana Limestone using the multiaxial cell available at the University of Colorado at Boulder. The tests include uniaxial compression and tension, biaxial compression and combined biaxil compression- tension. Flexible fluid cushions and brush bearing platens were used for compressive and tensile loading respectively in order to minimize loading end effects on the test specimens. The paper begins with a review of previous investigations on the multiaxial behavior of rock. Then, test results are presented in terms of

Jan 1, 1984

By L. L. McDaniel

Copper smelters of various kinds have operated in the Morenci district since 1872, but all have been abandoned with the exception of the present Morenci Smelter of Phelps Dodge Corporation, which was completed in 1942. During the five-year period starting in 1937, the Morenci ore body was prepared for open pit mining, pilot mill test work was carried out, and a complete reduction works, of which the Smelter is a part, was designed and erected. Actual construction work on the Morenci Smelter was started in the fall of 1940, and warming up of the units began on April 1, 1942. Charging of the reverberatory furnaces commenced on April 18, 1942, and the first anode copper was produced on April 26, 1942. The smelter was originally designed to handle the production of the Morenci Concentrator on a 25,000 ton per day program, but by the time the smelter was in operation, plans were already underway to increase the smelter capacity to handle the production of the concentrator which was being enlarged to 45,000 tons a day capacity as a war-time necessity. This extension to the smelter was completed and the new units were put in operation toward the beginning of 1944. The original smelter consisted of a smelter crushing plant, bedding plant, two direct-smelting reverberatory furnaces with two waste-heat boilers on each furnace, three converters, an anode department, a stack, and all of the usual accessory smelting equipment. The extension consisted of increasing the bedding plant from three to five beds, the reverberatory department from two to four furnaces, and from four to eight waste-heat boilers, and the converter department from three to six converters. A third converter aisle crane was added and additions were made to the flue systems and conveyor systems throughout the smelter; but no change was made in the smelter crushing plant or the anode department, and the same stack was used for all additional Smelter units. A blister casting machine was installed at that time in the south end of the converter aisle to handle excess and emergency production above the capacity of the anode department and in 1947 a converter aisle skull breaker and a lime burning plant were added as the final units for a complete plant. The choice of direct smelting over calcine smelting for the Morenci Smelter was made after careful study by members of the Western organization of Phelps Dodge Corporation and after test runs on direct smelting of Morenci concentrate had been made at the Douglas Smelter of Phelps Dodge Corporation. The Morenci furnace charge is made up of comparatively high grade concentrate with no ores of smelting grade available and with only flux, a small amount of copper precipitate and the usual amount of smelter secondaries to be smelted with the concentrate. The simplicity of direct smelting for this charge and the large amount of waste-heat steam available from direct smelting operations were factors influencing the decision to adopt direct smelting for Morenci. The design of the Morenci Smelter and the type of units selected followed best experience at the Douglas Smelter of Phelps Dodge Corporation. A description of the original smelter before operations started was given in an article in the May 1942 issue of Mining and Metallurgy. The purpose of the present article is to describe the enlarged Morenci Smelter, with a discussion of metallurgy and operating practice and to show tabulations of operating and metallurgical results obtained. Because of beginning operations during the early years of World War 11, many problems caused by labor shortage were encountered, but no major difficulties developed in starting the new plant. However, because of labor shortage, full scale Smelter production was not reached until the fall of 1946. Fig 1 shows a general plan of the Morenci Reduction Works. The arrangement of the smelter equipment is shown in Fig 2, a sectional view of the smelter is shown in Fig 3, and the smelter flow sheet is shown in Fig 4. Metallurgy The metallurgy of direct smelting, being more or less fixed by the character of the charge, is not subject to the control available in calcine smelting. Slags may be modified by the addition of suitable fluxes, but the grade of the matte is determined almost entirely by the iron:copper ratio of the concentrate. The direct smelting operation involves distributing the wet concentrate along the sidewalls and in the bath of a reverberatory furnace by means of some suitable feeding device and raising the temperature of the charge so that first the moisture is driven off, then the first-atom sulphur is eliminated, and finally the sulphide portion of the charge melts and runs into the bath, carrying with it the non-sulphide portion which has been partially fluxed to form a suitable slag. The fusion of the non-sulphide portion is completed by contact with the irony converter slag which is regularly being poured into the reverberatory furnace. The smelting rate of the charge is influenced by the mineralogi-cal composition of the sulphide portion of the concentrate and by the composition and amount of the non-sulphide portion including the fluxes added. The copper in Morenci concentrate is chiefly in the form of chalcocite, intimately associated with pyrite, and non-sulphide content is very low so that

Jan 1, 1950