Search Documents

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By Vic Sterner

As cities and towns continue to grow, the need to install sewer, water, gas and other utilities becomes a necessity and the blasting of trenches for these service lines probably constitutes one of the most important forms of blasting in built-up areas. There f o re, understanding how explosives can be safely used in the most efficient manner is of prime importance. The need for protection against flyrock must be emphasized. The first consideration is that all explosive c h a rges should be located well down in the blastholes. The golden rule is to ensure that the depth of top stemming is never less than the burden on the hole. In the case of shallow holes, the minimum depth of stemming should not be less than 18 times the charge diameter, if airblast and flyrock are to be controlled. If there is a doubt, then additional cover and/or blasting mats should be used. Putting too much burden on blastholes is another possible cause of flyrock and raising ground vibration levels. Overburdening of explosive charges will also result in the blastholes not breaking to grade. This in t u rn re q u i res additional drilling of shallow holes down in the trench to achieve grade, thus further increasing the h a z a rd of flyrock .

Jan 1, 2004

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing minerals substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.

Jan 1, 1976

By Simon W. Houlding

The mining community is geographically remote and widely dispersed. There is a growing requirement for formalized professional development of members by professional associations, and increasing recognition of the advantages of continuing education and training by both individuals and corporations. Working against these trends are the increasing expense and time commitments required for attendance at conventional courses and workshops. The result is a perceived need for a readily accessible source of continuing education and technical reference on the Internet. The design constraints for an Internet model for professional development include: ? browser compatibility, with any time, any place, any pace accessibility; ? a content presentation model with low bandwidth requirements, appropriate interactivity for examples, tools and reviews, and viewer performance monitoring capabilities; ? formal accreditation of content, presentation and process so that viewer achievements may be formalized in terms of widely recognized Continuing Education Units; ? availability of tools for conversion of source material to the presentation format with minimal effort. A model that meets the design constraints is presented and illustrated by examples from an existing Internet site for continuing education in mining.

May 1, 2002

By Raymond Philippe

Background ?Hatch Water has worked with most major mining companies in Chile on water supply and optimization projects ?Many(copper) mining projects are located in Northern Chile, which hosts the driest desert on earth Water supply options in Northern Chile ?River ?Availability/Rights ?Well(Brackish) Water ?Availability/Rights ?Municipal Wastewater ?Water rights ?Volume ?(Desalinated) Seawater ?Infinite source ?Cost depends on distance and altitude ?Recycling/Reutilization ?Water losses All these options present water quality issues

May 1, 2009

By Ziyad Abunada, David O’Connor, Abir Al-Tabbaa

"Abstract Contaminated land remediation using soil mix technology (SMT) is a relatively recent development which has been shown to be a cost effective and versatile system with numerous environmental advantages over other remediation techniques. The added complexities and variability associated with contaminated sites has escalated the need for field trials, field monitoring and specific QC measures to be undertaken for this setting and was the rationale behind project SMiRT (Soil Mix Remediation Technology). The main aim of project SMiRT was field validation, testing and assessment to provide stakeholder confidence in SMT and increase its uptake for land remediation in the UK. The field trials involved the treatment of 800 m3 of soil, through applying six different remediation techniques with four different SMT systems and introducing over thirty binders and binder compositions with a range of installation methodologies. Various issues were faced during the installation process and which were addressed on site. This paper presents some aspects of early age field observations, field monitoring, in-situ testing, coring and laboratory testing of cored samples and highlights some lessons learnt, providing valuable information on the issues that need to be addressed for this application of SMT.IntroductionAlthough soil mix technology (SMT) was developed in the 1960s in Japan and Sweden for geotechnical applications, its potential in geo-environmental applications became evident more recently the 1980s in the US and in the 1990s in Europe, having since increased to provide a range of remediation systems (Al-Tabbaa and Evans, 2003; Al-Tabbaa et al., 2011). The most common applications to date have been (a) the construction of low permeability containment walls or cut-off walls to contain a contaminated site; (b) stabilisation/solidification (S/S) treatment, with cementitious binders, for physical and chemical encapsulation of contaminants in soils and (c) the installation of permeable reactive barriers (RPBs), which are permeable walls that intercept the groundwater flow and remove contaminants from it, by mixing special additives with the native soil. Contaminated land remediation using SMT is a cost effective and versatile approach with numerous technical and environmental advantages over other remediation techniques. These advantages include the use of simple and well established techniques and equipment, speedy implementation, applicability to sites of any size and to multiple contaminants, elimination of off-site disposal, low risk and low emissions. There is a lack of competing alternative technologies that offer the same level of versatility and economic, environmental and social benefits, under current environmental legislation constraints. In addition, most currently available contaminated land remediation techniques are only partially effective, and are relatively contaminant-specific. This makes SMT a promising and timely contender to lead the market place in offering a cost-effective, efficient and low risk solution to contaminated soil and groundwater remediation and has resulted in a range of recent innovations."

Jan 1, 2014

By Belcher C. B

A procedure was required for the rapid determination of silicon in low-alloy irons and a suitable method used the formation and reduction of silicomolybdic acid at 50°C. The procedure gives results for elemental silicon and this enables the correct computation of oxidation requirements in basic oxygen steelmaking. The method could be useful in iron foundries which have not installed direct reading spectrometers.INTRODUCTIONOxygen steelmaking experiments required rapid determinations of 0,5-1,6 per cent silicon in iron (3-4 per cent C) within 10 min of sampling; a reproducibility better than ±0.03 per cent Si was desired. Only elemental silicon (Si°) is of interest as a fuel in basic oxygen steelmaking technology, and the proposed procedure determines exclusively this form of silicon. The method is described as it may prove useful to other workers although the interference study would be incomplete for some applications.The analysis of silicon in iron is frequently obtained using direct reading spectrometers, but for the proposed experiments the spectrometers could not be used because of the prohibitive distance from the furnace. It should be noted that spectrometers determine both the elemental silicon and that present as silicon dioxide in occluded slag and inclusions.The silicon content of iron and steel is determined in this laboratory by spectrophotometric measurement of a "molybdenum blue" colour. The reactions involved have been extensively investigated; Strickland (1952) showed that a...

Jan 1, 1965

By Martin Herrenknecht

The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge to provide efficient traffic infrastructure, such as a modern public transportation system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are also essential. Additionally, supra-regional transportation routes such as long distance water diversion schemes are the challenges for the future. All these projects are as demanding as they are characterized by a tight time schedule.

Jan 1, 2010

Pillars with width to height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented, which illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

Jan 1, 2006

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By Grigor Mishev, Georgi Petrov, Benjamin Cebrian

Before designing a single blast or all the blasts on a pit level, it is critical to assess the main goal on each. To do this, a series of constraints must be taken into account: wall protection, vibration control, flyrock hazards, fragmentation required, desired displacement as well as economy, equipment efficiency. The tool to do this is the Blast Master Plan. Many mines fail to integrate on its elaboration key stakeholders such as planning, operations, geology/geotechnical and milling departments. Designs not only have to provide consistent behavior of the blasts, but have to make sense all in one with the geological and geotechnical conditions as a starting point. Once blasts are designed under an organized set of priorities, and complemented with quality controls, optimization is possible on a large scale.

Jan 1, 2016

By R. J. Hundhausen

This report describes the exploration and recent utilization studies the Bureau of Mines conducted on the Iron King, Chambers, and Dry Camp chromite deposits in the John Day district, Grant County, Oreg. The field investigations were undertaken during parts of 1939 and 1942 to determine the tonnage and grade of chromite in the district that could be utilized as a war reserve for the steel industry. As a result of the Bureau's field work, which included construction of 9 miles of access road, 6,204 feet of diamond drilling, 195 channel samples, and 1,020 linear feet of trenching, an ore reserve of 208,000 tons of 22-percent chromic oxide was indicated in the 3 deposits. Less than 1,000 tons of this ore has been mined since the field work was completed because the 2 largest deposits are submarginal in grade and there is as yet no incentive to develop and mine the ore. Since the war, however, the Bureau has been seeking means of utilizing the ore. Two methods of utilization that show promise are direct smelting of the ore in an electric furnace and use of the chromite for making refractory brick.

Jan 1, 1956

By Rodrigo Rocha de Meira

O laminador de tiras a frio n° 3 da CSN apresentava perdas de produtividade ao processar aços de elevada resistência microligados, com limite de escoamento mínimo igual a 340 MPa, dotados de largura superiores a 1400 mm. Devido à crescente demanda do mercado automotivo relativa a esta família de aços, tornou-se necessário um estudo para optimizar a produtividade do equipamento e não desestabilizar o fornecimento aos clientes. O estudo consistiu em testar parâmetros de processo alternativos, objetivando abastecer o laminador de tiras a frio com bobinas laminadas a quente dotadas de resistência mecânica ligeiramente menor, para promover maior estabilidade operacional no equipamento a partir da redução das cargas de laminação. As alterações propostas resultaram no aumento de produtividade do laminador de tiras a frio, sem comprometer as características mecânicas do produto final.

Jul 30, 2018

By Eduardo Reis de Oliveira

As ligas fundidas de Alumínio são uma excelente opção para substituir os materiais convencionais devido às suas excelentes propriedades mecânicas. Assim, o uso destas ligas nas indústrias aeroespacial e automobilística estão em uso crescente. As propriedades mecânicas finais das peças são muito dependentes da macro e microestrutura, que são resultantes do processo de solidificação. Portanto, o controle dos processos de solidificação de ligas permite maximizar as propriedades mecânicas de um componente mecânico. Os parâmetros de processo que podem interferir na estrutura final de uma liga são amplos. Tem-se como exemplo: composição da liga, taxa de resfriamento, modo de extração de calor, condições de fusão e tratamento do metal líquido e temperaturas envolvidas durante a fundição. O objetivo deste trabalho foi estudar uma liga binária de Al-Mg usando a técnica solidificação unidirecional. As macroestruturas e microestruturas obtidas foram correlacionadas com parâmetros térmicos tais como: velocidade de deslocamento da isoterma liquidus (VL) e taxa de resfriamento (?). E os espaçamentos dendrítico secundários (?2) com a microdureza HV. A composição da liga analisada foi Al-Mg com 3% de Mg e com patamares de superaquecimento (?TV) variando em 20, 40 e 60ºC.

Oct 30, 2017

By N. Hiroyoshi, R. D. Corpuz, M. Ito, Hokkaido University, C. B. Tabelin, S. Veerawattananun

"Acid mine drainage (AMD), the very acidic and heavy metal-contaminated leachate generated when pyrite-bearing rocks are exposed to surface oxidizing conditions, is a serious environmental problem encountered after the closure of mines and mineral processing operations. In this study, we investigated the effects of soluble phases and metallic oxides, which are commonly found in strongly weathered pyritic wastes, on pyrite oxidation. Strongly weathered pyrite containing melanterite (FeSO4·7H2O) as the main soluble phase was obtained from Furikusa mine, Japan. The sample was washed using two methods to vary the relative amounts of melanterite in the sample. The effect of metallic oxides on pyrite oxidation was evaluated using ultrapure hematite suspensions. Our results showed that under acidic conditions, the effect of soluble salts on the oxidation of pyrite was stronger than hematite. More thorough washing of the sample resulted in the formation of an arsenic-bearing iron-oxyhydroxysulfate coating that minimized pyrite dissolution. This oxidized layer became relatively thicker and mechanically stronger when hematite was introduced after the more thorough removal of soluble salts. Characterization of this “coating” coupled with geochemical modeling suggest that it is most probably composed of two materials: schwertmannite and scorodite. Based on these results, a new approach to suppress pyrite oxidation by directly using iron-oxyhydroxysulfate as coating material is introduced.INTRODUCTION Acid mine drainage (AMD), the very acidic and heavy metals-contaminated leachate produced in closed/abandoned mine sites (Evangelou, 1995), mineral processing and coal cleaning tailings (Evangelou, 1995), and tunnel construction waste rocks (Tabelin and Igarashi, 2009, Tabelin et al., 2012), is one of the oldest and probably the most serious environmental problem of anthropogenic origin. When released to the environment, it rapidly pollutes river, soil and groundwater systems leading to the destruction of affected ecosystems. AMD is produced when pyrite (FeS2), one of the primary gangue minerals in sulfide ores and coals, is exposed to oxidizing conditions as illustrated by the following reactions:"

Jan 1, 2016

NASA has received direction for lunar habitation beginning in 2024. Prior to then, it will be necessary to learn about how lunar soil can be used to promote civilization on the moon. Questions must be answered: ?Will it support plant life?,? ?Can it be used as a construction material?,? ?What is needed to maximize health and safety?,? and ?Will it affect equipment, tools, machinery, and clothes?? The only samples available for study came from the Apollo Missions. Because the expense of bringing more material back to Earth is prohibitive, there is not enough available to perform studies to answer the above questions. Hence, there is a great need for its synthesis. Most efforts to date have concentrated on making ?simulant? from single natural resources of volcanic rock. However, another possibility is to use resources here on Earth to extract the minerals of interest into concentrates or so-called ?separates? using traditional mineral processing techniques, and then mix the separates in appropriate ratios to simulate the lunar soil. In this paper, results from a study in which dry Road Norite outcrop and wet mill tailings from the Stillwater Mining Company?s Concentrator located near Nye, MT were examined. Of course, the in-side challenge is to make ?separates? from gangue minerals.

Jan 1, 2012

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

Evaluation of Grinding Medium Wear in Stirred Mills The standard fine grinding machines in the minerals industry are stirred mills whose performance largely depends on the competency of the grinding medium. Medium wear in stirred mills is one of the key parameters for medium selection. A wear evaluation methodology is developed and applied in this paper to measure the wear rate of river sand using a laboratory batch stirred mill. The procedure is demonstrated by testing the sand medium in a 0.55 kW batch stirred media detritor (SMD). The sand wear rate determined in the laboratory batch mill is successfully scaled up to that determined on a full-scale Metso 355 kW SMD mill.

Sep 13, 2010

By Raffaele Alves Paranhos

Devido à alta competitividade no mercado siderúrgico se faz necessário à otimizaçãodo processo como forma a atendermos a demanda de produção com um menorcusto de transformação. Nesse contexto, foi utilizado para desenvolvimento dotrabalho a metodologia DMAIC e os conceitos do “LEAN”. O objetivo do grupo foiestratificar o custo de produção do equipamento e atuar nos principais fatores, tendocomo princípio a redução do desperdício, aumento da produtividade da mão de obra,aliada a produtividade de tonelagem de material. Na estratificação do custo deprodução identificamos o “Rendimento metálico” como sendo o fator maissignificativo e propomos ações internas que contemplaram alteração de programade automação para melhora do descarte da cauda (Final) da bobina e com issoatingindo valores recordes de aproveitamento material acabado. Fizemos reduçõesde lead time do nosso processo eliminando os tempos que não agregam valores,aumentando a produtividade do equipamento. Com este trabalho conseguimosreduzir consideravelmente o custo de transformação do equipamento, além, deaumentar sua capacidade produtiva.

Aug 16, 2017