Search Documents

By M. O. Lai

"Metal matrix composite (MMC) with composition of Al-4.Swt.%Cu reinforced by IOwt.%TiB2 or ISwt.%SiC particulate has been successfully fabricated using powder metallurgy technique. Disk, compression and beam specimens were prepared with (a) layered structure containing ductile Al-4.Swt.%Cu with brittle Al-4.Swt.%Cu/TiB2 or Al-4.Swt.%Cu/SiC layers, and (b) homogenous constituent with composition of Al-4.Swt.%Cu/lOwt.%TiB2' The specimens for the fracture toughness measurement were built through three ductile-brittle-ductile alternating layers. For the beam specimens, the layers were built through brittle-ductile-brittle sequence. The brittle layer consisted of Al-4.S%Cu with fixed amount of reinforcement. Fracture toughness testing revealed an increase for layered composites although the total amount of the reinforcement was the same for all disk specimens. The increase in fracture toughness is due to the existence of ductile layers which manifests a strong influence on delaying the occurrence of fracture. It acts as a barrier to resist the propagation of crack and hence increases the fracture toughness of the layered MMC specimens, Delamination in the beam specimens was observed to be due to shear stresses. Fracture surfaces of both disk, compress and beam specimens were characterized using the SEM. IntroductionMechanical and thermal properties can be achieved by the incorporation of refractory secondary phases to constrain the plastic flow of the matrix in a metal matrix composite (MMC). The size of the reinforcement particulate incorporated must be in the range larger than the dislocation cell size and strongly bonded to the matrix (I). Particulate reinforced metal matrix composites hence provide high modulus, improved wear resistance and strength (2-4). Because of the incorporation of refractory phases which are generally brittle, the major limitation in the mechanical properties of MMCs is their limited ductility in comparison to their base metals. Cracks normally initiate from the reinforcement and voids (4, 5). Due to the lack of ductility, cracks propagate rapidly with increase in load. As a result, the interactions between reinforcement particles and propagating cracks have recently been of great research interest (6). In addition, volume fraction of reinforcement and aging condition of the matrix significantly affect the mechanical behaviour of MMCs. In the case of AI-3.5%Cu reinforced with varying volume fractions of SiC particulate, it has been found that the probability of particle fracture increased with increasing volume fraction of reinforcement (7)."

Jan 1, 1996

By Jose Antonio Silva Souza, Emanuel Negrao Macedo, Iara Ferreira Santos, Otacilio Dias, Luis C. A. Venancio

"The Bayer process alumina production generates 0.7 to 2.0 ton of bauxite residue (BR) and an average of 1.0 ton of C02 per ton of alumina produced. The direct reaction of exhaust gases to reduce the alkalinity of the BR may allow a triple gain: improve the storage conditions, open a range of new applications for BR and sequester from 16 to 102 kg of C02 per ton of alumina. This paper shows the measurement of C02 captured during a pilot scale reaction of a suspension of BR in water with flue gas, produced from direct oil burning. Three different types of reactors were used: one spray tower and two packed columns. The inlet and exhaust gases were analyzed using electrochemical and non dispersive infrared sensors. The pH of the suspension was monitored during and after the reaction to evaluate the buffer effect.IntroductionAlumina is mainly produced from refining bauxite using the Bayer process. This process consists of extracting the aluminum oxide through its dissolution in caustic soda and the separation of insoluble residues. The remaining bauxite residue (BR) although not particularly toxic, poses risks to the environment due to the large volume and its reactivity. According to the latest technology it is stacked on sealed deposits specially constructed. To date the vast majority of the bauxite residue that has been produced was stored and were not incorporated into any existing production processes to significant amount with exception to some extent of the sintering process residue at Russia and China [l]. On the other hand, a strategic goal was set in 2010 by the Bauxite and Alumina Committee of the International Aluminium Institute (formed by the majority of the industries) to reuse 20% of BR in 2025 [2]. China has established the same objective for 2015[1].This paper is a sequel of two others presented at TMS 2010/2012 [3-4] and describes:• A pilot plant assembled for testing the carbonation process of BR with gaseous effluents similar of the refining process.• The methodology used to measure the amount of C02 captured during the carbonation process.• The results of the carbonation process, the C02 capture and the buffering effect of the pH.This process is studied in order to consume minimal power and use the effluent as efficiently as possible in different reactors from low cost to ultra high performance. The process is designed for minimizing the power consumption and equipment investment."

Jan 1, 2013

By Hongmin Zhu, Suning Liu, Kai Huang

"Recovery of silicon particles from the cutting slurry for the manufacturing of solar grade silicon is very important to recycle this kind of special resource. The challenge is to separate the silicon particles from the mixed abrasive particles which contain SiC. Various methods such as sedimentation, centrifugation, and flotation have been conducted, while in present work, a simple and effective novel method was proposed to study the separation of Si and coexisting SiC particles in the cutting slurry. The new process is based on the size difference between the two kinds of microparticles. And the membranes with the different pore sizes of 1µm, 2µm, 3µm and 5µm were used to test the pass ratio and separation efficiency of the suspension. Results shows that the effective separation of Si and SiC microparticles was obtained under the optimal conditions, and indicating great potential of practical enrichment of Si from the coexisting abrasive particles.IntroductionWith the development of the world economy, energy shortage and environment problem is becoming more and more seriously. Solar energy, which is regarded as one of the most important new energy in the word, has received much attention and interest from the scientists [1, 2]. More than 80% solar cells are manufactured by the high purity polysilicon as the raw material. The main process of producing silicon wafer is by multi-wire slicing. In this slice processing, large amount of slurry is produced. The slurry contains more than 30% wt silicon powder, silicon carbide powder as the abrasive, scraps of metal chips, as well as cutting abrasive suspension polyethylene glycol (PEG). The high-purified silicon powders are worth recycling and reusing as the materials for preparing solar-grade silicon though it is a big challenge [3].Most of the current studies were focusing on the recycling of the silicon carbide and PEG, while work on the recycling of the high-purified silicon is not so been focused since there is lacking of very effective separation and recovery technologies till up now. Nishijima utilized the method of superconducting magnetic to recycle the abrasive [4]. Wang applied a combinational process of chemical treatment, high-gravity centrifugation, high-temperature precipitation technique and directional solidification to enrich the silicon [5]. And other purification methods, such as centrifugation [6], froth flotation technologies [7], electrical filed separation [8] and phase-transfer process [9] have been employed. The disadvantages such as using poisonous media or complex equipments decrease the feasibility and efficiency of the above mentioned techniques."

Jan 1, 2014

By K. S. Raja, M. Misra, S. K. Mohapatra

"Ordered arrays of TiO2 nanotubular photocatalysts were prepared by a simple anodization process. Band gap states of the TiO2 were altered by controlling the anodization electrolyte composition and thermal annealing conditions that resulted in enhanced photo activity. These nanotubes were used for reducing CO2 to methanol either by photochemical or photo electrochemical routes. Pd nano-particle loaded TiO2 nanotubes were employed for photochemical reduction of CO2 to methanol that showed a conversion rate of 12 x 10-3 mol m- 2h-1. Carbon modified TiO2-xCx type nanotubes were used as photo anode and Ti as cathode for photo electrochemical reduction of CO2. The potential of Ti cathode was maintained at -0.5 V SCE. The formation rate of methanol was determined as 13 x 10-3 mol.m-2h-1.1. IntroductionGlobal warming due to emission of carbon dioxide is a serious environmental concern. The atmospheric concentration of CO2 is about 384 ppm by volume and about 3 x 1012 tonnes by weight. Burning of fossil fuels and deforestation are the leading causes for increase in the anthropogenic CO2. More than 32 x 109 tonnes of CO2 are released per year (based on 2006 data) worldwide from the fossil fuel. Pumping CO2 from the fossil fuel power plants into deep ocean basin is one of the most discussed disposal options. The other potential option is converting this green house gas into valuable fuels.Carbon dioxide feed stock can be converted into fuels of solid, liquid or gas phase by chemical, electrolytic, photocatalytic and photo-electrocatalytic methods. Reduction of CO2 to fuel form of any phase requires energy. The reduction process should be energy efficient so that we do not spend more energy and emit more (indirect) CO2 in the process of converting CO2. From this point of view, conversion processes occurring at room temperature look attractive.Electrolytic conversion of CO2 into various forms such as methane1, ethane2, ethylene3, methanol4,5, ethanol6, n-propanol, formic acid7, and formaldehyde has been widely reported. The standard equilibrium potential (at pH: 0) for reduction of CO2 to methanol is 0.14 VSHE and to methane is 0.2 VSHE which is thermodynamically more favorable than hydrogen reduction. However, the gas phase reduction is kinetically complex requiring effective electrocatalyst. The major issues with electrolytic conversion of CO2 to useful products are:"

Jan 1, 2010

By Edouard Asselin, Guikuan Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe( II )-Fe(III)-H2S04 solution at 25°C and 70 °C. Results from the calculation ofspeciation in the above solution reveal that, at both 25 °C and 70 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller values for the reversible potential of the ferric/ferrous couple based on the Nemst equation. Exchange current densities of the ferric/ferrous couple were obtained by extrapolating the cathodic linear Tafel line to the reversible potential and are on the order of 10-7·10-6 A/cm2 at 25°C and 10·6-10-5 A/cm2 at 70 °C, respectively. The transfer coefficients were about 0.35-0.38 at 25°C and 0.35-0.45 at 70 °C. Polarization plots of CPC and CPP under different nominal Fe3+/Fe2+ ratios are in good agreement at 25 ·c and at 70 °C. Based on the obtained exchange current densities, the rate constant k, was calculated and is on the order of 10-1 cm/s at 25 °C and 10 1 cm/s at 70 °C.IntroductionChalcopyrite is the most abundant copper mineral in nature, accounting for about 70% of copper reserves in the world [I]. In recent years, the metallurgical industry has been searching for a hydrometallurgical process as an alternative to pyrometallurgical treatment due to high emissions of S02 and capital costs associated with smelting. Activity in this area has increased recently due to some inherent advantages associated with hydrometallurgical processing, such as the possibility of treating low-grade ores (increasingly more abundant in the case of copper) and easier control of waste, with the attendant benefits to the environment [I]. Chalcopyrite is highly refractory under most hydrometallurgical conditions, owing to the formation of an anodic passivation layer on the chalcopyrite surface which renders the process kinetics very slow. Most of the currently proposed processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Sulfuric acid is preferred over all other leaching reagents in terms of cost, environmental friendliness, and ease of its regeneration during electro-winning. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale,"

Jan 1, 2012

By Jian Li, S. Penttilä, P. Liu, W. Zheng, C. Bibby

"The materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. The current Canadian pressure-tube supercritical water (SCW) concept design requires core outlet temperature of 650 °C at 25 MPa with peak cladding temperature reaching as high as 850 °C. Aside from oilier challenges, there is currently very limited data on candidate stainless steels' corrosion resistance under this operating condition. Austenite stainless steels that include 316L, 304H, AL6XN and 3 l0S that cover a wide range of Cr contents are promising candidates for either direct in core applications or as base coating materials. However, their corrosion resistance has not been tested systematically under this stringent condition. In this study, these types of stainless steels are tested, and their corrosion resistances are compared.IntroductionThe Canadian pressure-tube supercritical water (SCW) concept will operate at a core outlet temperature of 650 °C at a pressure of 25 MPa, with potential peak cladding temperature reaching as high as 850 °C. High-temperature corrosion resistance is one of the key design requirements for fuel cladding components. As summarized by Allen [1 ], most testing to date has been carried out at temperatures below 730 °C. To date, SCW corrosion data above 600 °C is very limited. Even at relatively low temperature exposure to SCW (e.g. 500 °C), F/M steels develop a thick oxide layer rapidly, while some austenitic stainless steels develop thinner surface oxide. Ni based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of intermetallic precipitates [2-5]. Dissolution of major alloying components from all of these alloys could also pose significant problems for downstream piping [6]. Kaneda et al. [7] suggested some modified stainless steels provide better SCW general corrosion resistance, with no sign of SCC under the slow-strain rate test.Cho [8] suggested that as the Cr content increase, general corrosion resistance improved at 510 °C and 25 MPa. However, similar to Cho's work, most of the SCW corrosion resistance assessments were based on weight change measurement. This can be unreliable due to potential exfoliation of thick oxide film. Besides, there have been no systematic SCW corrosion resistance tests for candidate stainless steels under higher temperatures. SCW corrosion rate increase dramatically for alloys tested at 600 °C [1]. It is also important to understand the role of major alloying elements under this stringent operating condition, not only for fuel cladding components' materials selection, but also for coating materials development."

Jan 1, 2013

By E. A. Chavarriaga, L. J. Jaramillo, O. J. Restrepo

"This paper presents the results of the manufacturing ceramic pigments with spinel structure, using methods of synthesis of low temperature. In this work we obtained spinel structures type by the methods of Self-combustion, Coprecipitation, Microemulsion, Gel citrate and Pechini. These methods become an attractive alternative to traditional method (ceramic method), since we can work at a lower temperature, reducing manufacturing costs, lower fuel consumption, less wear on equipment and other environmental and economic implications. Also it is possible to have control over features such as stoichiometry, morphology of the products, reaction times and structures. The products obtained by these routes will be used in the manufacture of ceramic pigments and characterized using different techniques such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV-VIS spectrophotometry.IntroductionSpinels are ternary oxides AB204, where A and B are cations occupying tetrahedral and octahedral positions respectively. These oxides exhibit interesting electrical, magnetic and catalytic properties [1-4], depending on its nature, charging and intrinsic distribution of ions [5].The most widely used method to prepare spinels has been through solid state reaction, which consists of mixed oxides at high temperatures [6, 7]. In the last years, there have been a strong tendency to use chemical routes for the synthesis of crystalline ceramic particles at low temperatures [8,9]. Unconventional methods currently employed for the synthesis of complex oxides are Gel citrate method, Pechini, Spontaneous combustion, Microemulsion and Coprecipitation. Pechini method [10, 11], based on polymeric precursors, does not require high temperatures and allows stoichiometric control for greater reproducibility. This method involves the formation of a polymeric resin between a metal quelate and polyhydroxy acid of alcohol by polyestirification.Coprecipitation is important for many environmental problems related to water resources, including acid mine drainage, migration of radionuclides in waste repositories dirty, transport of contaminant metals in the industry, metal concentrations in aqueous systems and the technology of wastewater treatment. The coprecipitation process can vary in each case; the partition in the solid phase can be carried out by surface adsorption, ion exchange, surface precipitation, occlusion and formation of solid solution. The formation of solid solution is the result of structural incorporation of the marker in structural support sites resulting in a minor component in the solid solution with the host phase that has a very low solubility of pure solid [12]. Synthesis by gel citrate method allows the use of a route to obtain ceramic pigments from a very simple experimental system in which the stoichiometric control, the size and shape of the particles and the purity of the phases obtained can be controlled more accurately [13]."

Jan 1, 2012

By A. Dell’Era, M. Pasquali, C. Lupi

"An electrochemical cell has been designed to treat very diluted cobalt solutions, i.e. those deriving from recycling processes of lithium-ion batteries. A reticulated vitreous carbon sponge was used as cathode and a Pt-coated Ti net as anode. A controlled potential electrolysis has been carried out in a solution flowing in the cell and maintained at a constant pH of 6.5. Considering the cathode dimensions (10.0 cm * 10.0 cm * 1.25 cm), rather high volumes of solution (>1 litre) can be treated with flow rates up to 1.6 l/min. The process yield is obviously related to the solution concentration; it has been observed that, starting with a solution containing 200 ppm of Co2+, the yield is initially ~35-40%, but it decreases to ~20% when 80% of the initial cobalt content has been electrowon. The yield increases up to ~50% if the carbon electrode is coated by cobalt. The conditions allowing a fast and complete removal of cobalt are outlined. Introduction Industrial liquid effluents containing heavy metal ions arise not only during hydrometallurgical processing, but also in many sector of chemical industries utilizing metal catalysts and process reagents. These waste solutions containing low quantities of metallic ions can be treated by chemical precipitation, solvent extraction, ion exchange, etc. before final discharge. All these techniques could be efficient for complying the aqueous effluents with the severe rules related to the environmental impact, but they can not directly produce metals. Particularly the chemical precipitation presents two main drawbacks, huge amount of sludge prodction and reagent costs to produce this useless and sometime dangerous sludge that have to be considered. Electrochemical technologies can be used for the treatment of effluents polluted by metal ions, showing the following advantages in comparison with other processes: 1. recovering of the polluting substances in metallic forms, with subsequent reusing; 2. absence of process slag, which should be subsequently disposed of. In this work an electrochemical reactor with a reticulated vitreous carbon cathode and a platinated titanium net anode has been designed and utilized for removal Co from waste aqueous solutions. Porous materials have been used as electrodes for this cell, as their high specific surface area favours the treatment of these low metal content solutions (1-7). This kind of electrodic material presents very interesting chemical-physical characteristics such as: low density, low thermal expansion and high electrical and thermal conductivities; particularly the reticulated vitreous carbon (RVC) presents a very elevated void volume, rigid structure, good resistance to temperatures in non-oxidizing environments and very low resistance to fluid flow."

Jan 1, 2008

By Sebastião Ribeiro, Leonardo Carneiro Sardinha, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

The glass tube of spent fluorescent lamps is contaminated with mercury, which might be a serious hazard in the case of conventional recycling by melting with other glasses. A possible solution could be its incorporation into a clay body to fabricate common fired ceramics such as bricks and tiles. The objective of this work is to characterize a type of fluorescent lamp glass waste to be incorporated into a clayey ceramic. The characterization was performed in terms of wettability tests to evaluate the interaction between the surface of the clayey ceramic and glass waste as a function of the firing temperature. The results showed that the contact angle decreased with increasing temperature, reaching a value of 79°, at a temperature of 1100°C, but not sufficient to completely wet the ceramic. However, compatible chemical composition and reduction of porosity by the flow of soft glass waste between the clay particles favor the consolidation of the ceramics structure above 900°C.

Jan 1, 2015

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By S. G. Kumar

Experimental studies on high carbon steelmaking through LD Converter - Vacuum Arc Degassing - Bottom Pouring route to produce low oxygen steels were carried out. The results indicated that it is possible to produce steel with a total oxygen content of less than 15 ppm. Thermodynamic and mass balance calculations are made on low-carbon steels that are treated by a complex deoxidation practice based on primary deoxidation of aluminum, manganese and silicon additions; followed by secondary deoxidation of vacuum degassing with simultaneous additions of aluminum. The results showed that primary deoxidation is mainly due to aluminum and the effect of carbon under reduced pressures on deoxidation of molten steel that is already killed by aluminum is negligible. The effect of process parameters on total oxygen content of steel, like carbon content, slag composition and inert gas purging, are discussed.

Jan 1, 1994

By Jae-Ho. Lee

For some electronic applications where a dispersed electrically-conductive particulate-phase is employed, the conductivity of the surface (or near-surface region) of the particles provides for the primary mechanism which determines its electrical conductivity. Particles of a less expensive material, which may have desirable thermal-expansion properties, when coated with silver offer a means of also obtaining desirable electrical properties and at low cost. The research conducted was focused primarily on the development of silver-coated tungsten particles for thick-film polymeric conductors. The ammoniacal electrolyte was formulated from silver-nitrate, glycine inhibitor and formaldehyde reductant. The reduction, and subsequent deposition, of silver occurred selectively on the surface of the tungsten particles. Coated particles were assessed by SEM imaging. The thickness of the silver coating was estimated to be approximately 100nm on the basis of a mass account and the coating being uniform. The electrical conductivity of a silver-coated tungsten-powder pellet was found to be similar to that of a silver-powder pellet, of identical geometry.

Jan 1, 1997

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Onsan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By J. Murdoch Mackenzie

Two commercial nickel solvent extraction plants treating laterite leach solutions and using LIX®84-I have been operated in Australia. These circuits employ similar extraction chemistry but differ in their leaching and stripping operations. An alternative process involving elements of both can be conceived. The preparation of the feed solution to solvent extraction plays an important role in nickel extraction using LIX®84-I and the special features of manganese removal and cobalt oxidation in the preparation of the PLS are discussed. This paper compares these three circuit configurations with special reference to the extraction and reductive stripping of cobalt, the transfer of zinc and copper to the strip aqueous, ammonia transfer and sulfur transfer. The potential degradation of the organic and remediation using re-oximation is discussed. Keywords: Nickel, Solvent Extraction, Oxime

Jan 1, 2004

By René Winand

Due to chemical and electrochemical behavior of the most common additives in copper electrorefining i.e. gelatine, thiourea and chloride ions, it is essential to simulate as far as possible true industrial practice while performing laboratory experiments. The three additives must be studied simultaneously, and added continuously to the electrorefining cell. Ratio electrolyte volume to cathode area; ratio bleed flow to cathode area; hydrodynamic conditions; residence time of electrolyte in the cell; current density; electrolyte and soluble anode must be as near as possible to industrial ones. Experiments performed in the author's laboratory show that under these conditions, reproducible results can be obtained at normal industrial current density and at high current density as well. Problems are however still encountered when developing a sensor for additives monitoring, due to electrolyte redox potential and to substrate influenced thin layer deposition.

Jan 1, 1995

By Michaela Dina Stanescu, Emilia Visileanu, Eftalea Carpus

"The recovery and reintroduction into the economic circuit of the textile material resources must be considered as component parts of the strategies of harmonizing the relationships between the economic growth, consumption of natural resources and environmental protection of the existing socio-economic system.The waste recovery for ensuring a sustainable development is a major concern of all industrial researches. In the textile domain, the concern in this matter is becoming more evident. An important role in manufacturing textile products it has the notion of eco-design, which has grown considerably over the last twenty years with increasing awareness of environmental and social problems in the industry.Introduction“Humanity must learn from the global financial and economic crisis experience""- is the conclusion of the policy makers who should develop a strategy designed to reinvigorate the economy and make possible an"" intelligent, sustainable and favourable to inclusion” growth, by a better coordination of national and European policies.The new vision for social market economy is based on three priority areas: smart economic growth, the development of an economy based on knowledge and innovation; sustainable economic growth, the promotion of a competitive economy with low carbon emissions and an efficient use of resources, as well as an inclusive economic growth, the promotion of an economy with high degree labour employment, which would generate social cohesion. The recovery and reintroduction into the economic circuit of the textile material resources must be considered as component parts of the strategies of harmonizing the relationships between the economic growth, consumption of natural resources and environmental protection of the existing socio-economic system.The waste recovery for ensuring a sustainable development is a major concern of all industrial researches. In the textile domain, the concern in this matter is becoming more evident. It is obvious that at the origin of pollution there are the technological processes of textile processing with impact on air, water, soil, as well as the storage processes. In all phases of obtaining a product, a series of secondary products and textile wastes with impact on the environment occur. The product used becomes also a factor of environmental pollution, which in most cases fails to assimilate."

Jan 1, 2012

By Qiu Dingfan

The Slurry Electrowinning Process (SEP) is a new hydrometallurgical method and clean technology, Sulfide ores can be treated by the SEP without S02 emission and the sulfur from the sulfides can be recovered in element form which is easy to stockpile and can be transported at low cost. In a special slurry electrowinning cell one can achieve at the same time the leaching of elements from the feed and the electrowinning of metals from the electrolyte, Because the anode reactions are utilized for leaching of some elements the consumption of the energy is decreased, SEP also has the advantage of separation some elements, It is especially suitable for treatment of complex concentrates containing Pb, Cu, Au, Ag and S, which could hardly be accepted by any smelter. In this work, the behavior of different metals in this process has been studied and it was found that the separation of metals in some minerals is possible through the SEP, Beijing General Research Institute of Mining and Metallurgy (BGRIMM) has studied the possibility of the SEP to treat bismuth concentrates containing S, Be and F in laboratory and pilot-test scale as well as in commercial plants, The commercial plant was set up in 1997, It has been in operation since that time, According to the results of laboratory experiments and pilot- plant test, a new plant to treat complex gold minerals was set up in 1998 and is in operation in 1999

Jan 1, 2003

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Ousan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By J. K. Brimacombe, I. V. Samarasekera, B. G. Thomas

"Mathematical models have been developed for the processing of static cast steel ingots and are app1ied to investigate the mechanisms for the formation of panel cracks. Panel cracking is an intermittent but persistent defect that causes affected steel ingots to be scrapped. A two-dimensional, finite-element, heat-transfer model was formulated and employed to calculate the temperature distribution in both large and small steel ingots during the various processing stages from initial casting to the start of rolling, including solidification, cooling in the mold and in air, reheating in the soaking pit, and subsequent air cooling. The stress state in the ingot arising from the calculated temperature variations was then determined. This involved the development of a transient, elasto-visco-plastic, finite element, thermal stress model, including the effects of phase transformation volume changes and kinetics creep, and temperature-dependent, mechanical properties. The results of the mathematical model predictions of temperature and stress were then used to determine the mechanisms and to suggest solutions for two different types of panel crack formation. Mid-face panel cracks apparently form during air cooling when the mid-face surface temperature is between the Arl and 500~C. Off-corner panel cracks appear to initiate internally during the early stages of reheating but do not propagate to the surface until much later. IntroductionPanel crack formation in static-cast steel ingots is a defect that has been plaguing the steel industry for several decades. Although the problem is intermittent, it is also serious since affected ingots must be scrapped. Panel cracks are manifested as two distinct types of cracking problems. ""Mid-face"" panel cracks are found exclusively in small, 2 to 6 ton, medium carbon steel (0.3 to 0.7% C) ingots and usually exhibit a single, continuous, longitudinal crack down the center of one of the ingot faces as shown in Fig. l (l). ""Off-corner"" panel cracks often form roughly oval, discontinuous crack patterns on the wide faces of large, 20 to 30 ton ingots as seen in Fig. 2 (2). They affect only low carbon steels (0. l to 0.2% C) with high manganese content. Both defects affect only aluminum-treated steels and are caused by a combination of intermediate temperature ductility loss involving aluminum-nitride precipitation and thermal stress generation. The ductility problem has received a good deal of attention which was the subject of a recent review (3). The present study was undertaken to investigate the thermal stress aspects of the problem through the development of mathematical models of heat transfer and stress generation in static-cast steel ingots. The ultimate objective was to elucidate the mechanisms of formation for both types of panel crack and to evaluate possible solutions to the problem."

Jan 1, 1986

By Tracie Zoeller, G. Paul Neitzel, Jr. Sanders

"As-cast aluminum alloy microstructures are highly segregated. Coring occurs when solute is rejected during solidification resulting in a non-uniform solute distribution across the dendrite arms. Furthermore, coarse constituent phases are formed in the interdendritic channels as a result of coring. These constituents are either soluble or insoluble and can form from the major solute elements, or the impurity elements iron and silicon. The dissolution of these constituents, or precipitates, is an important consideration in determining the microstructural evolution of an alloy. The properties of an alloy are significantly affected by the morphology of the precipitates. Precipitates can be either beneficial or detrimental to the properties of the alloy. Regardless of the nature of the precipitates present, it is useful to understand the dissolution process. A diffusion-limited dissolution model for planar precipitates is presented and compared to an analytical solution and to models in the literature. Experimental data for the dissolution of AhCu precipitates in a dilute alloy are compared to the proposed model, and found to have good agreement.IntroductionDuring the processing of precipitation hardening alloys, beginning with the solidification step and ending with the final solution heat treatment step, there are a variety of particles that form. Some of these particles must be dissolved and solute redistributed and re-precipitated in a more homogeneous distribution than as it first appears in the as-cast microstructure. The particles can be classified by size as microstructure develops during processing. Coarse particles that form during solidification can either be soluble, partially soluble or insoluble. These particles can be the result of coring of the major solute elements as well as the limited solubility of elements such as iron and silicon. Iron and silicon can combine with the major solute elements such as copper in 2xxx alloys forming coarse phases often referred to as constituents. Figure l(a) shows the as cast microstructure with the constituent phases, Al2Cu and the insoluble phases containing Al-Fe-Mn-Cu-Si [7]. During preheating the soluble phases such as AhCu that were formed by eutectic decomposition must be taken back into solution, whereas the insoluble phases remain essentially unchanged by most thermal operations. Figure l(b) and (c) show some of these constituents after subsequent preheating steps. In Figure l(b), AhCu platelets are shown and in Figure l(c) the remnants of the AhCu phase are noticeable, along with Mn-bearing dispersoid phases. Reduction in the volume fraction and size of these phases improves the ductility and fracture toughness as well as reducing the inhomogeneities that occur during coring. Also adjacent to the dendrite arm boundaries are smaller AhCu phases that precipitate by a solid-state transformation on cooling to room temperature."

Jan 1, 2004