Search Documents

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By J. W. Lyman

Nickel-metal hydride (Ni-MH) battery electrodes have been developed as a substitute for cadmium-containing negative electrodes. Use of Ni-MH electrodes offers enhanced electrochemical properties in many instances as well as reduced environmental toxicity. Rechargeable batteries using Ni-MH electrodes are also strong candidates for electric vehicles. During the production and secondary reclamation of these battery types, recycling procedures will be needed to prevent environmental impact caused by these wastes as well as to recover the value inherent in the scrap. The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical technology that separates and recovers purified metallic components from Ni-MH battery scrap of two types, AB, and AB,. An investigation of acid dissolution and metal recovery techniques has determined several processing alternatives that may be used to promote the successful recycling of much of the battery fabrication scrap and eventual secondary scrap. Although recovery techniques have been identified in principal, their applicability to mixed battery waste stream and economic attractiveness remain to be demonstrated.

Jan 1, 1995

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By G. A. Irons, D. Guo

"The average spout height and width produced by bottom gas injection in a water model of a steel ladle were measured with an image processing technique. It was revealed that the spout height could be described by a Gaussian curve. A combined SIMPLE -VOF model was developed to simulate the liquid surface and flow. The results showed that, though the model produced reasonable velocity distributions and free surface positions, the spout height due to the dynamic head of the rising liquid was substantially lower than observed, indicating that the bubble dynamics at the bath surface play an important role in spout height.IntroductionDue to the enormous importance of gas injection and stirring in metallurgical processes, there have been numerous publications on water and numerical modeling of such vessels. The free surface of the bath has received considerably less attention, despite its importance. At the free surface there are often important chemical phenomena occurring that require a good understanding of the fluid flow; these would include reoxidation of steel, metal splash and fume formation. Furthermore, to understand the details of slag-metal interactions such as slag entrainment, metal losses to slag and the transport phenomena associated with refining reactions, it is necessary to understand the plume and spout interactions first.There have been few experimental studies of the free surface of liquid in gas-injected ladles [1- 3], and even fewer on numerical modeling. Brimacombe and co-workers [1] studied the gas void fraction in the spout region, using a double-tip electrical resistance probe. This sensor cannot distinguish between gas in bubbles about to break and gas in the freeboard. Thus, it is a matter of judgement as to the position of the free surface. Schwerdtfeger and co-workers [2] used a single probe configuration with a wire and a counter electrode in the liquid, so that the height of the continuous liquid phase was unambiguously determined. Irons and co-workers [3] measured the spout height by ultrasonic and electrical capacitance techniques. These techniques were as reliable as the resistance techniques, but were restricted to low flow rates."

Jan 1, 2001

By Krzyszof Borowiec

With the aim of determining the thermodynamic conditions for sulfation of impurity elements, in particular magnesium, in titaniferous slags the equilibrium gas composition for the sulfation reaction: MO + so2 + 1/2 02 = MS04 has been studied by an EMF technique with a solid zro2 + Cao electrolyte. Here M denotes the impurity elements: Mg, Ca and Mn, and the following _oxide systems have been studied: Ti02-MgO-Fe2 o 3 , Ti02-MnO-Mn2 o 3 , and Ti02 -CaO-Si02 , all in the . temperature range 700-1000ºc. Reproducible EMF values were obtained by adding small amounts of -Na2so4 to the oxide-sulfate mixture. From the observed results the Gibbs energy of formation of the phases Mg 2Ti04 , MgTi03 , MgTi 2o 5 , MnTi03 , CaTi03 , and CaTiSio5 , as well as the activity of MgTi05 in the solid solution with Fe2Ti05 have been calculated. The results show that, from a thermodynamic viewpoint, sulfation of these impurities in titaniferous stags i:s favorable- at around and below 800ºC.

Jan 1, 1985

By Jae-Ho. Lee

Mercury is a toxic contaminant encountered in the extraction of gold from mercury-containing ores. It is found in the leach solution of CIP circuits and in the cathodes of the electrolyte cells used to electrodeposit the gold. The research conducted has examined the potential for selective removal of mercury from synthetic Au-Hg-CN electrolytes containing only gold, only mercury, and both gold and mercury. Cyclic voltammograms were obtained for mercury- coated copper electrodes with these cyanide electrolytes. Exchange current densities were determined from the voltammograms in the low overpotential region. Laboratory scale batch- electrolysis at constant current was also conducted for the electrolytes containing only mercury and both mercury and gold, at 20 and 50°C and from which the kinetic behavior associated with the process was analyzed. The surface of cathode before and after electrolysis was also characterized and a copper mercury intermetallic (CyHg,) was identified. Gold codeposited with mercury during the later stages of electrolysis. The results of this work corroborate that the mercury-amalgam copper electrode offers a viable electrochemical technique for the selective removal of mercury, however a high-surface-area cathode-cell would have to be utilized to provide for the desired selectivity.

Jan 1, 1994

By Walter Curlook

An improved process of hydrometallurgical treatment of laterite ores of the limonitic type for the recovery of nickel and cobalt using sulphuric acid has been developed and patented [I]. The major improvement is brought about by recycling a significant portion of the "mother liquor" emanating from the pressure leaching reaction back to the feed preparation stage thereby substituting for all or at least a major proportion of the fresh water that must be added. The amount of process effluent waters is correspondingly reduced. Concomitantly with the major savings in fresh water requirements, a degree of reduction in new sulphuric acid requirements is effected, along with a savings in limestone and lime required for subsequent neutralizations. Keywords: Acid pressure leaching; Nickel laterites

Jan 1, 2004

By H. Sieber

Multilayer samples of tantalum and aluminum with the composition of Al-25Ta were prepared by cold rolling of elemental foils. The microstructure and phases were characterized by XRD, SEM and TEMISAED and the reactive phase formation was examined by DSC and DTA measurements in multilayer foils rolled for different deformation levels. The rolling procedure yields a decrease of the Ta particle size in the Al matrix and also results in the formation of a multilayer structure with a thickness of the elemental foils down to 200 nm in average. No phase formation is observed during the cold rolling procedure. While XRD and DSC measurements show no phase formation up to the melting of aluminum for samples rolled up to 40 F&R (fold and rolling) passes, in samples rolled for 50 or more F&R passes a first phase formation reaction yield an interfacial layer of TaAl3. Contrary to former studies in the investigated cold rolled Al- 25Ta multilayers the reaction starts at temperatures as low as about 340°C. The first stages of the reaction are associated with two exothermic maxima, that increase in amplitude and shift to lower temperatures with increasing number of F&R passes. At higher temperature the TaA13 reaction layer thickens very sluggishly and yields a third exothermic maxima at about 600°C. Isothermal DSC scans show the reaction is not finished for samples containing elemental particles larger than 1 pm after annealing at 550°C for 5h. In all the investigated samples no Al- Ta phase other than Tad3 was observed to grow for heat treatments up to 800°C. Multilayer samples heated up to 1400°C show a morphology consisting of small AITa2 particles embedded in a single phase TaA13 matrix. The multilayer microstructure and reaction product morphology are characterized by SEM and TEM investigations in cross-section and plan view geometry.

Jan 1, 1998

By K. C. Liddell, B. Dou

"In producing multilayer films for magnetic data storage applications, the interfacial roughness must be controlled in order to obtain high quality materials with reproducible properties. The present understanding of the effect of roughness on multilayer properties such as magnetoresistance is sketchy, particularly for electrodeposited films. In this study, quantitative atomic force microscopy was used to characterize surface morphology before and after Ni films of varying thickness were deposited on Cu cathodes. A multinuclear multilayer growth mechanism is supported by both the deposition conditions and the AFM images, and a multinuclear multilayer model gave a satisfactory fit to measurements of the density of peaks on ultrathin Ni films between 0 and 8 nm thick.Alloys consisting of alternating ferro-and paramagnetic layers have begun to replace Permalloy in the sensing elements of magnetic hard drives. The operating principle of the new read heads is giant magnetoresistance (GMR), and they are smaller and more sensitive than previous inductive heads (1). Experimental studies on sputtered multilayers have emphasized the role of layer thickness and interlayer roughness in determining the presence and size of the GMR effect (e.g., 2,3,4,5,6). However, roughness in electrodeposited multilayers has rarely been measured, even though read heads are likely to continue to be made by this process for some time to come. Cu/Ni can be considered a model system for understanding processing-microstructure-property relationships in electrodeposited multilayers and is the most widely investigated of all such systems (e.g., 7,8,9,10,11,12). Nevertheless, the roughness of the interfaces in Cu/Ni electrodeposits has not been systematically characterized by quantitative techniques, and in all studies reported so far, the total deposit thicknesses were considerably greater than the 10 nm needed for most sensor applications (1). The thinnest such films were about 50 nm (7)."

Jan 1, 1998

By K. Fukushima, K. Baba, H. Kurokawa, M. Yamagiwa

"The Toyo smelter has expanded its anode production capacity from 126,500 to 239,000 t/year by introducing technical oxygen into blast air for flash and converter furnaces and improving smelting facilities. Significant efforts were made in the expansion not to increase the number of workers, which mean development of some automation systems for the copper converters and anode casting wheel. The efforts have resulted in the above-mentioned increase in productivity and a saving of production cost as well as a decrease in the number of workers for the anode casting operation.IntroductionThe Toyo smelter has been performing a highly stable and pollution free operation since its commencement in 1971 (1). Its distinctive features are the on-line control by process computer (2) and the high productivity without trouble. But owing to the so-called oil crisis in 1979, we were faced with a sharp increase in production cost. To decrease the production cost, some measures for saving of energy were planned and carried out, such as conversion from oil to coal in a flash furnace (3), the heat recovery from converter slag and the introduction of technical oxygen in blast air with the intention of energy saving as much as possible.The first increase in production capacity and some savings of production cost were attained in 1982 by the introduction of technical oxygen in blast air for the flash furnace without major modification of the furnace as shown in Table I. The capacity of an oxygen plant is 7,800 Nm3/H as 90% O2 . Part of oxygen from the plant is also supplied to tuyeres of copper converters through an oxygen holding tank with a volume of 830 m3 at 7 kg/cm2-G."

Jan 1, 1989

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By Xuyang Liu, Xuewei Lv, Chenguang Bai, Meilong Hu

"The electro-deoxidation process for ilmenite concentrate in molten salt was studied by cyclic voltammetry and AC impedance spectroscopy. The results from cyclic voltammetry are consistent with those of AC impedance spectroscopy. The results showed that the electro-deoxidation process for ilmenite concentrate consists of two steps. In the first step, Fe is reduced from the ilmenite concentrate. The second reaction is the decomposition of TiCh. CaTiCh is an intermediate product. At low voltage, the electrochemical reaction is the main step. With the increasing potential, the diffusion of ion is the main rate controlling step for the electro-deoxidation of FeTiO3.IntroductionTitania and titanium-rich products are mainly prepared from ilmenite concentrates (FeTi03), which contain about 40%-60% T1O2 after ore dressing and other physical or chemical processes [1]. At present, the main methods to prepare titania are the sulfuric acid process and the chloride process, but the sulfuric acid process consumes a large amount of sulfuric acid and the materials requirements for the chloride process are strict [2], Since the Electro-Deoxidization in Molten Salt (FFC) method was put forward in 2000, many researchers have successfully extracted the metal and alloys by this method, such as Ti, Cr, Tb, Si, Al-Si, TiV, FeTi, etc. [3-7], FeTi alloy is a typical hydrogen storage material, and because of its favorable properties, the preparation of FeTi alloy has become a hot research topic [7-9]. However, the mechanism of electro-deoxidization has not been studied thoroughly [10-11]. Therefore, in this study, the electro-deoxidation process for titanium concentrate was investigated by electrochemical methods, and the study makes a contribution to improving the current efficiency of the electrolysis."

Jan 1, 2012

By M. Brian Maple

A rich variety of phenomena are produced by superconducting-magnetic interactions in rare earth and actinide compounds. These phenomena, and the materials in. which they have been observed, are described in this talk, with an emphasis on the new high superconducting transition temperature (Tc) copper oxides. The Materials The-materials in which these phenomena occur can' be divided into two classes. In the first group, there are two distinct interpenetrating systems of electrons, a set of localized 4f or 5f electrons and a set of itinerant electrons. The localized f electrons carry magnetic moments and interact with the spins and momenta of the the itinerant electrons, which are involved in the superconductivity, via exchange and electromagnetic interactions; respectively. This category includes materials containing rare earth (R) and actinide elements with partially-filled f electron shells which have been inroduced as substitutional impurities [e.g., La1-xCexA12, Th1-xUx] or form a sublattice in compounds [e.g., RRh4B4, RMo6S8, RMo6Se8, the high Tc. superconductors RBa2Cu3O7-d(d - 0.05)]. Materials of the second type are characterized by a single band of electrons that is responsible for both superconductivity and magnetic order. This group includes heavy electron rare earth and actinide compounds [e.g., CeCu2Si2, UBe13, UPt3, URu2Si2], and the high Tc copper oxide superconductors such as the hole-doped systems Lag- MxCuO4 (M = Ca, Sr, Ba, Na) and RBa2Cu3O7-d(0 =d= 1) and the electron-dope system Ln2-xMxCuO4-y (Ln = Pr, Nd, Sm, Eu; M = Ce, Th; x = 0.15; y - 0.02).

Jan 1, 1992

A comprehensive numerical capability for the analysis of Thermal Spray (TS) systems consisting of a three-dimensional compressible, turbulent flow Navier-Stokes model and a multi-phase particle flow model in Lagrangian formulation, was developed. This capability is validated for a set of flow conditions typical for TS. The developed methodology is used for analysis of the JP-5000 TS gun gas and coating powder flow conditions. Modeling and analysis of particle/turbulent eddies interaction is performed. Details of gas flow field, particle temperature, and particle velocity histories, and particle temperature, velocity profiles in the system are presented. For the validation of numerical analysis, the computed results are compared with available experimental measurements. The flow phenomena for different flow parameters are analyzed and explained as the results of gas dynamics and heat and momentum transfer between the gas and particle phases. This methodology can be used for process control and reliability improvement, and has the potential to significantly improve TS gun performance through control of its parameters.

Jan 1, 1996

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.

By Akira Yazawa

The continuous converting has attractive advantages, but further experimental studies on the slag are required, when the process is considered thermodynamically. The summarized experimental results, obtained with iron silicate slag and with ferrite slag and results relating to actual operation are described and discussed in this paper. At first, equilibrium relations at controlled oxygen potentials among three melts of silica-saturated iron silicate slag, white metal and copper are investigated. The results obtained for slag agreed with the thermo-dynamical predictions. Namely, to suppress a magnetite separation, the system should be at high temperature; in the case of the S02 gas of 10 kPa, for example, magnetite did not separate from the slag at 1300°C, but at 1250 and 1200°C the slag was saturated with magnetite even at lower SO2 pressure. Copper losses caused by dissolution of its oxide increased with increasing 5O2 pressure, and were slightly lower than those reported in previous papers without the matte phase. When the continuous converting slag does not contain any appreciable amount of silica - in contrast to the conventional smelting slag ferrite slag would form, but there was no published fundamental work on-ferrite slags. Hence, the melting behavior and activities of the system CaO-Cu2O-Fe2O3 have been investigated. The liquidus diagram in nitrogen atmosphere was, constructed using both thermal analysis and quenching method. The low liquidus temperature region without magnetite separation was found in the part of low content of Cu2O in the section Cu2O-CaO-Fe2O3 and Cu2O?Fe2O3¬CaO?Fe2O3. The activity of Cu2O in the system was also measured. Slags, composed-of CaO, Cu2O and Fe2O3, in platinum crucibles were equilibrated at 1250°C and controlled oxygen pressures. After quenching, the-composition of slag and platinum crucible were determined qualitatively. On the thermo-dynamic analysis of the results, iso-activity lines were drawn, and it was shown that the slag in the converting furnace of the Mitsubishi process exists in an adequate region of the composition triangle.

Jan 1, 1976

By Von L. Richards

Rapid Freeze Prototyping (RFP) is a novel solid freeform fabrication technology that creates parts by depositing water droplets and freezing them rapidly to form layers. An investigation into the smallest thickness that can be achieved by the RFP process was conducted. The factors that could significantly affect the thickness of the part built by this process including substrate temperature, volumetric feed rate, table velocity, nozzle frequency, nozzle standoff distance, and head pressure were considered. A shell building technique for use with the RFP system has been developed. Thin wall ice patterns have been invested using production shell building techniques and an alcohol-based slurry. The finished shells were quantitatively evaluated by inspecting their total shell thickness, mold cavity dimensional reproducibility, and shell strength. Pattern loss is influenced by not only the alcohol / water interaction but also the starting thickness as it relates to thermal mass.

Jan 1, 2008

By Zdzistaw MiGzkowski

At KGHM Polska Miedi S.A. a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass ex-change inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed. The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ? The second zone moves slower into the grain and the rate of the movement is deter-mined by the presence of oxygen. In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined. The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003