Search Documents

By George H. Klein, B. Kent Merritt, Anthony Crisci

During the past decade, over 114-km (71-mi) of 0.25-m (10-in) to 3.7-m (144-in) finished diameter tunnels have been driven below Metropolitan Houston as part of a major program of water and wastewater improvements. This large effort has seen the introduction of midwestern technology with over 18-km (11-mi) of man-entry pipe jacking and European and Japanese technology with over 21-km (13-mi) of microtunneling. Owing to the high water table; a stratigraphy consisting of stiff fissured clays containing numerous layers, channels, and lenses of water-charged sands and silts; and active faults, many challenges existed for designers and contractors alike.

Jan 1, 1991

By Edward S. Plotkin, Thames F. Peyton, Gary A. Almeraris

This paper describes high speed tunneling by drilling and blasting in a heavily populated urban area. The project consists primarily of mining 2500 m (8237 ft.) of tunnel through mica schist, excavating three shafts approximately 200 m (650 ft.) each and concreting lining 5300 m (17,400 ft.) of 7.34 m (24 ft.) inside diameter tunnel. The techniques developed and equipment utilized to ensure a high rate of tunneling advance are described. Extensive planning and good communications were especially essential in maintaining production on this project since tunnel mining, tunnel concreting, and shaft excavation all proceeded simultaneously from one common work shaft and a single heading.

Jan 1, 1985

By P. R. Busmann, D. J. Rogers

The Bureau of Reclamation's Syar Tunnel project included excavation of a 9.2 kilometer (5.7 mile) long, 3.6 meter (11.8 ft) diameter tunnel through gently dipping sedimentary rocks consisting of shales, siltstones, sandstones and limestone. The tunnel was supported full length with precast concrete invert segments and lightweight steel sets and lagging. Several world records for advance rate were set, including 57 meters (187 ft) in an eight hour shift and 127 meters (417 ft) in a 24 hour day. The tunneling system utilized a remanufactured and modified Robbins hardrock TBM and a 9,280 meter (30,450 ft) long, 61 centimeter (24 inch) wide, continuous conveyor system.

Jan 1, 1991

By James A. Morrison, Stephane Carayol, Paul H. Madsen

The Rio Piedras Alignment Section 7 of the Tren Urbano is currently being constructed beneath a historic commercial section of San Juan. Different portions of the section are being constructed using open cut, cut-and-cover, New Austrian Tunneling Method (NATM), Earth Pressure Balance Machine (EPBM), and as tacked drift mined support system. The combination of complex geology, low ground cover, and several innovative construction methods present many challenges to the ground control program. Mining and construction sequences were first developed to minimize ground movements and risk of damage to structures. A unique compensation-grouting program was developed to improve the ground, limit settlement, and recover settlements incurred due to mining.

Jan 1, 1999

By Jan M. Mutmansky

Since 1973 when the first edition of the SME Mining Engineering Handbook was published, many significant changes have occurred in the US mining industry. The industry went through a fairly prosperous period immediately after 1973, but then many economic pressures came to bear on mining companies, particularly in the metal and coal branches of the industry. These pressures changed both the mining methods used and the general economics of the mining methods. As a result, the industry today is different in many ways titan it was in 1973. A general summary of some of the more important changes that have come about will be provided here as well as some assessment of the effects of these changes on the choices of mining methods. In the metal mining industry, the most significant trends were increased surface mining, the use of larger and more efficient equipment, and increased technology and automation. The primary impetus for these changes was unprecedented competition from foreign producers. In many cases, this competition came about because of the nationalization of foreign mines and the tendency for these mines to become a source of foreign exchange. Under these circumstances, the mines could be operated even though they were not profitable. As a result, domestic

Jan 1, 2008

What is your assessment of the status of the mining industry as we see some evidence of an economic recovery? I am optimistic about the short and midterm prospects for the industry and, hence, for the professionals in the industry that constitute the majority of the SME membership. All who will read this interview recognize that the quality of life we enjoy today is largely a result of our achievements in the mining and minerals processing sectors. I believe that the sustainability of that quality of life and the aspirations of other sectors of the global community to attain that same lifestyle will significantly depend on the continued successes of these industries. Looking at some of the traditional economic indicators, we see predictions of continued increases in gold prices during the next 12 months as a new round of quantitative easing keeps real interest rates low and drives excess capital flows from countries with trade surpluses - who have traditionally parked their money in U.S. government bonds - into other investable assets, such as gold. On the fuel side of the industry, we have during the last decade seen a steady rise in the cost of coal, and some of the recent spot prices have seen dramatic increases. Some suggest that coal prices may rise sooner than anyone expects, as global reserves are revised downward. This is based on the hypothesis that some of the main coal-producing countries are overestimating supplies and that coal prices could start rising far sooner than anyone thinks - with obvious serious implications for energy policy. Those forecasters note that, for the past couple of decades, global supply has been dropping at a faster rate than consumption.

Jan 1, 2011

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By Eugene C. Spilker

Cross country belt conveyors are becoming the preferred method of bulk material handling in the industrial complex. Installed cost, maintenance, reliability, simplicity and operating expense enhance this choice, especially when faced with rising cost and questionable availability of liquid fuels. Conveyor flights are getting longer, faster, and higher in capacity, and are being installed in rugged terrain. Rights of way are often difficult to obtain. All these considerations lead up to design aspects well beyond those for in-plant conveyors. This paper points out some of the aspects that lead to the successful design of a cross country belt conveyor system.

Jan 1, 1980

By J. W. Mustard

The Macmillan Pass tungsten property (MacTung) is the largest known copper-tungsten, calcic, exoskarn deposit in the Western Hemisphere. Located on the border between the Yukon and Northwest Territories in northwestern Canada, the deposit crops out on Mt. Allen within the Selwyn Mountain Range. It was discovered in 1962 by a subsidiary of AMAX Inc. and has since been explored by 16,300 meters of surface and underground diamond drilling and by 800 meters of underground development. Geologic reserves are in excess of 30 million tons, grading slightly less than 1.0% WO3. Scheelite (CaWO3 ) is the main mineral of economic interest. Accessible by road, the property is not in production. Previously estimated reserves at MacTung have been unable to fully utilize all the geological controls on mineralization. In the past three years, however, an intensive program has been underway to improve our understanding of the deposit and to use the resulting information in a more precise way. This paper will discuss the key aspects of the geology as they specifically relate to reserve estimation and will demonstrate how these controls are being used in a geostatistical model of the deposit.

Jan 1, 1985

By P. Zhang

This paper gives a review of promising technologies for phosphate processing, and covers flotation, analysis and process control, as well as tailings treatment and utilization. Air bubbles of less than a µm in size, combined with relatively large bubbles, have been demonstrated, both in the lab and on a pilot scale, to improve flotation dramatically, by reducing reagent use while improving product grade. Innovative use of polymers has allowed rapid dewatering of fine tailings with a final product that does not segregate. The first online laser-induced breakdown spectroscopy (LIBS) analyzer was created, allowing rapid analysis of wet samples using the laser technology. Many large commercial projects are successfully pursuing the utilization of phosphogypsum.

Feb 1, 2012

By Zoë Dugdale, Gerald Poplin, Tim Bauerle

"Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetitive duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising.Mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a cookie-cutter approach. However, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; long commute times due to mine site remoteness; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present all together. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining.While the burden of fatigue on the mining population has not yet been evaluated thoroughly, methods and measures of fatigue management remain a popular point of discussion. Many commercial suppliers and consultancy groups have begun to develop technologically based fatigue monitoring systems (McMillian, 2013). Some technologies can monitor vehicle operators for indicators of wakefulness, such as percent eyelid"

Jan 3, 2018

By P. K. Kaiser, M. Cai

When designing an efficient and effective support system for burst-prone ground, it necessary to select the most appropriate, i.e., the ‘right’ support components, including areal and reinforcement components. For this paper, it is assumed that the areal support is not the weakest link and the support performance is controlled by the rock reinforcement and holding components (bolts). We discuss the loading modes of rockbolts under static and dynamic loadings and analyze published data from laboratory and field tests. The mechanisms of energy absorption of dynamic rockbolts are presented and rockbolts are categorized based on factors such as energy absorption capacity, energy absorption rate, direct and indirect energy absorption capacities, rock mass bulking or displacement control, and shearing resistance capacity. Guidelines for selecting the ‘right’ rockbolts to build an effective rock support system for burst-prone ground are provided.

Apr 26, 2022

By H. Hinds

Plant testing of DuPont's Activator Technology in the vat leach circuit of the Homestake mine shows increased gold recoveries of 3-5%. Activators are catalysts of gold dissolution in cyanide solution. DuPont received the patent for this technology in January, 1996. The test was run in the west sand plant alternating control and activated vats to reduce the variability in head grade and cyanide consumption. Activated vats had gold in the preg solutions earlier, higher gold recovery, and lower gold residuals. Activator addition did not adversely affect mill operations or the environment. Optimization of the technology continues.

Jan 1, 1997

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By Paul K. Sims

The Central City district is one of several adjacent mining areas in the Front Range, Colorado, that contain precious metal-bearing sulfide veins of Laramide (Late Cretaceous and early Tertiary) age. The districts are in the Front Range segment of the Colorado mineral belt, and are characterized by porphyritic igneous rocks of intermediate composition that have intruded Precambrian crystalline rocks in the core of the Front Range. The veins and minor stockworks that constitute the ore deposits in the district were formed largely as fracture fillings. The veins range from simple fissures to complex, branching lodes, and commonly range from less than 0.5 to about 1 m in width. The principal values are in gold and silver. The common metallic minerals are pyrite, sphalerite, chalcopyrite, tennantite, and galena; minor minerals are enargite, pitchblende, and gold tellurides. Quartz, cryptocrystalline silica, carbonates, fluorite, and barite compose the gangue. The ore deposits have a well-defined concentric zonal arrangement. A core of pyrite veins (central zone) is surrounded by a peripheral zone of galena-sphalerite vein with gold and silver. An intermediate zone contains transitional veins that have minerals characteristic of both the central and peripheral zones. The minerals were deposited in three stages during a single period of mineralization: uranium; pyrite; base metals, gold and silver. The wall rocks were altered primarily during pyrite-stage mineralization. Sericite envelopes developed adjacent to fractures, and were succeeded outward by zones of argillized rock. The valuable ore minerals were deposited in ore shoots localized by several types of structural controls, principally vein intersections, the physical nature and structure of the wall rocks, and irregularities along the fractures themselves. During supergene alteration, gold was concentrated in the upper, oxidized parts of the veins, commonly to depths of 50 m. The precious metal-bearing sulfide ore deposits are closely associated in space and time with the Laramide porphyritic igneous rocks and are believed to have been derived from hydrothermal fluids related to the magmatic activity. The ore deposits have mesothermal aspects and apparently formed in the temperature range 200°-320°C.

Jan 1, 2013

By Jacques B. Wertz

However excellent the geologic map of an area is, it can only show what is exposed on the ground. It cannot and should not generalize the information nor complete the picture by inference: this is left to the examiner. Consequently, it becomes justified for him to use all expressions of geologic structure in order to gain an additional dimension in geologic interpretation, and particularly so in mineral exploration. In previous studies related to Arizona, the known faults were the starting points and a host of interpolated, supporting geologic factors described in earlier publications ascertained the presence of a series of structural trends and lineaments found to be rather continuous and persistent, even though unsubstantiated by geologic maps. In present studies pertaining to the humid environment, with the same aim of seeking major structural trends and lineaments, the starting points are morphologic expressions such as straight lakes and straight segments of rivers, among others, because there generally is not enough geology available. An example is given herewith for an area that straddles the International Border, north of Spokane. In both semi-arid and humid environments, one observes that mineral deposits quite often occur close to the intersection of a major fracture or lineament with some secondary trend.

Jan 1, 1971

By Kyle Amoroso, Aaron K. McCain

Frozen soil shoring has been used for decades in the tunneling industry to provide temporary support of excavation for shafts and cross-passage excavations. However, horizontal penetrations through the frozen soil can prove to be challenging. The key to creating a stable portal through frozen ground is managing and mitigating groundwater flow into the excavation through the annular space surrounding the drill stem or casing. This paper will review different approaches that have been successfully used to penetrate frozen soil shoring on multiple projects.

Jun 13, 2023

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By J. R. Knudson

A major contribution to the art of blasting was made at the Cleveland- Cliffs Iron Company?s Hawkins Mine in Cashwauk, Minnesota during April of 1956. It was here that the first experiments with fertilizer grade ammonium nitrate were conducted-experiments which led to the development of the ammonium nitrate and fuel oil method of blasting which has been eagerly adopted by open pit and quarry operators throughout the United States. While this new blasting agent was a more or less natural outgrowth of the Akremite Process devised by Maumee Colleries of Terre Haute, Indiana; no one, to our knowledge, had used this particular combination of ingredients prior to this time. Certainly this was a "break-through" as far as the Lake Superior District was concerned. Akremite consists of a mechanical mixture of grained ammonium nitrate and a solid carbonaceous material packed in a plastic bag. At the time of its introduction to the Mesaba Range, Akremite sold for 10.5 cents a pound as compared to the 18 cent powder previously used in both wet and dry large hole blasting. The discovery of this agent was indeed a remarkable achievement, one that afforded a substantial reduction in blasting costs. However, Akremite proved to be only an intermediate step in the evolution of our present low cost explosives. Cleveland-Cliffs utilized prilled ammonium nitrate and fuel oil and then eliminated the mixing and packaging plant entirely by combining the two raw materials in the field at the drill hole collar or in the hole itself. Thus we have approached the ultimate in simplicity, for the blaster and his helper now manufacture their own explosives not only as they are needed but where they are needed, and at a cost of under 4 cents a pound. This two-man crew may charge and explode as much as 8 tons of ammonium nitrate in an eight-hour shift and in so doing break some 65,000 tons of ore.

Jan 1, 1959

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024