Search Documents

By Mostafa Benzaazoua, Bruno Bussière, Mukendi Kongolo

The desulphurization process has been proposed over the last few years for acid mine drainage control at certain mines, which generate low to medium grade sulphidic tailings (-3 to +25 wt% S). The environmental sulphur recovery, which means the sulphur to be floated to produce a non-acid generating final tailings, depends mainly on the intrinsic neutralizing potential of the tailings. However, in some cases the sulphur cleaning is complicated by other parameters which affect the flotation probability of the sulphide particles. In this study, a number of tests were conducted with a Hallimond tube and Denver Cell on both pure mineral and mine tailings. To develop a better understanding of the mechanisms of non-selective sulphide flotation, three types of approach were investigated in this work: (i) pure pyrite at progressive milling degrees, (ii) artificial mix of pyrite and quartz at different calibrated granulometry and (iii) same composition tailings with 26 % wt sulphur at progressive milling degrees. The effect of the granulometry on the sulphide flotation was demonstrated both. The results allow us to define a granulometry model, which can then be considered in the whole desulphurization modeling.

Jan 1, 2000

By John B. Draper

The 1980 Mine Dewatering Act was enacted to protect water rights and to allow mine dewatering to proceed where impairment of a water right might have otherwise created a bar to mine development. In New Mexico, new appropriations for beneficial use are subject to the State Engineer's jurisdiction and are granted only upon a showing of non-impairment. Before 1980, mine dewatering was not considered a beneficial use, nor was it considered waste. The Act brings mine dewatering under the jurisdiction of the State Engineer, makes it subject to the same requirements as an application for appropriation for beneficial use, grants the right to replace the water of users whose rights would be impaired by mine dewatering without a plan of replacement, and extends the right of replacement to non-mining appropriations of water for beneficial use, Application of the Act requires determination of the definition of impairment (the threshold of significant impact on existing water rights), hydrologic evaluations to determine the impact of the proposed dewatering, and preparation and execution of a plan of replacement to avoid impairment of existing rights.

Jan 1, 1983

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995

By M. S. Safarzadeh, V. Agarwal

"The solvent extraction of cerium(III) and samarium(III) from mixed solutions of all rare earth elements (REEs) except promethium using PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), an acidic extractant, was investigated. The effects of aqueous equilibrium pH, various acids (sulfuric acid (H2 SO4 ), hydrochloric acid (HCl) and nitric acid (HNO3 )), initial metal ion concentration and extractant concentration on the solvent extraction of Ce(III) and Sm(III) were systematically studied. From the experimental results, HNO3 and HCl were found to be the preferred aqueous media for the solvent extraction of both Sm(III) and Ce(III). The most promising experimental conditions of pH, PC88A concentration and metal ion concentration were identified for the extraction of Ce(III) and Sm(III). Separation results showed that H2 SO4 at pH 2 provided the best separation between Sm(III) and Ce(III). IntroductionIn recent years, demand for rare earth elements (REEs) has increased significantly because of their many commercial applications. REEs have especially important high-tech applications owing to their unique physical and chemical properties, and they are used in a wide range of areas such as catalysts, ceramics, magnets, lasers, glass, neutron absorption and alloys. As REEs have very similar physicochemical properties, their separation and purification from each other is challenging and gaining significant interest. Samarium (Sm) and cerium (Ce) are found in different REE minerals, including bastnäsite ((Ce,La,Nd(CO3)F), xenotime (YPO4) and monazite ((Ce,La,Nd,Th)PO4) at major production sites in the United States and China, as listed in Table 1 (Bleiwas and Gambogi, 2013). The most common acidic organophosphorous extractants used for REEs extraction and separation are DEHPA (di-(2-ethylhexyl)phosphoric acid), PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), Cyanex 272 (bis-2,4,4-trimethylpentyl phosphinic acid) and Cyanex 301 (bis(2,4,4-trimethylpentyl)dithiophosphinic acid) (Sarangi, Reddy and Das, 1999; Surampally et al., 2012; Tian, Jia and Liao, 2013). Out of these extractants, PC88A is known for providing higher separation factors (Acharya, Mishra and Misra, 2015). El-Hefny et al. (2010) investigated the kinetics of the solvent extraction of Sm from chloride media using sodium salt of Cyanex 272 and reported the extracted species to be Sm(OH)A2•2HA. Lee et al. (2005) investigated the solvent extraction of Sm(III) with PC88A and saponified PC88A from chloride solutions and found the stoichiometry of the extraction reactions to be 1.5 with PC88A and 3 with saponified PC88A."

Jan 1, 2017

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By Gregory M. Rumbaugh, Todd R. Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern USA. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence sinkhole on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the 5 events involved at least 12 benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on these factors and proposes a framework to assist mine operators where they identify similar hazards.

Jul 24, 2023

By S. K. Kawatra

Many mineral oxide and multi-component oxide (basalt) specimens break down into powders upon expo-sure to sodium vapor at elevated temperatures for extended times. This paper examines several possible mechanisms of oxide breakage by sodium vapor, both experimentally and from a thermodynamic viewpoint. The oxides for which reduction by sodium was thermo-dynamically favorable all exhibited some degree of fragmentation. The oxides which were not favorable for reduction by sodium did not exhibit fragmentation, with the exception of rutile, a titanium oxide. The rutile fragmentation was caused by the reduction of iron that was in solid solution in the rutile crystal structure.

Jan 1, 1995

By Muhammad Azeem Raza, Samuel Frimpong

Underground mining environments are inherently hazardous and can lead to emergencies where effective rescue and self-escape become critical. Missouri University of Science and Technology is pioneering new technologies for effective self-escape. The rescuers and miners need to be trained in these new technologically driven environments. Previous research in fields like aviation, medical surgery, and oil and gas drilling has demonstrated the effectiveness of virtual simulation training, but the mining sector has yet to fully adopt advanced tools such as eye-tracking and immersive training modules. This research proposes a comprehensive training infrastructure incorporating these technologies to enhance situational awareness and decision-making during emergencies. The novelty lies in the application of advanced miner escape and communication technologies, specifically designed to monitor and enhance cognitive responses in high-stress situations. By leveraging these technologies, the proposed training infrastructure aims to prepare the next generation of underground miners and operators, by equipping them with the necessary skills to manage emergencies effectively.

Feb 1, 2025

By Arthur F. Eidson

INTRODUCTION If a uranium mill worker is involved in an accident, analysis of excreta for uranium content and[in vivo] counting methods are used to estimate the extent of the possible exposure and to predict the pattern of uranium distribution among tissues (Spitz, [et al]., 1980). Interpretations of urinary excretion data are based on studies of human exposures to single uranium compounds including U02, U308, U03, UF4, U02F2 and UF6 (Alexander, 1974). Refined uranium ore (yellowcake) is a variable mixture of U03-NH3-H20 adducts (ammonium diuranate, ADU) and their thermal conversion product, U308. The variability in composition of yellowcake (Kalkwarf, 1979; Eidson and Mewhinney, 1980; Dennis, Blauer and Kent, 1981) complicates the interpretation of bioassay data from individuals that might have inhaled any single yellowcake material. A test system would be useful to estimate the dissolution behavior of a particular yellowcake aerosol inhaled by a worker and aid in the interpretation of bioassay data collected before and after an accident. A series of experiments was conducted for this purpose. The objectives of these studies were to: 1) develop specific criteria for comparing [in vitro] dissolution systems and 2) use the criteria to evaluate solvents, methods and experimental temperature and pH conditions used in previous studies. Dissolution experiments were conducted using different combinations of solvents, conditions and methods with a common yellowcake sample. Because little information is available from human yellowcake inhalation exposures to evaluate the [in vitro] results, criteria for evaluation of different tests were derived from a model of yellowcake dissolution in lung constructed from a number of cases in which humans were exposed to single uranium compounds known to be in yellowcake (Mercer, 1975). MATERIALS AND METHODS Materials The powder used in the tests was taken from one lot of yellowcake obtained from a commercial uranium mill. The same powder was previously designated as Mill D in Eidson and Mewhinney, 1980 and Mill 2 in Kalkwarf, 1979. The ammonium diuranate content was measured by infrared absorption to be 25% ± 1% (Eidson and Mewhinney, 1980). Solvents The compositions of the two biological fluid simulants used are compared in Table 1. Simulated lung fluid (SLF) (Kalkwarf, 1979; Dennis, Blauer and Kent, 1981) was chosen to simulate the composition [ ] of lung fluid as closely as practical (Moss, 1979). Simulated blood serum ultrafiltrate (SUF) (Eidson and Mewhinney, 1980) was chosen because of previous successful efforts to model human urinary excretion of inhaled plutonium aerosols (Kanapilly Raabe and Boyd, 1974) and the dissolution rate of 241Am02 in Beagle dogs (Mewhinney and Griffith, 1981). Major differences are that simulated lung fluid contains Mg2+ and a higher Ca2+ concentration than SUF and that SUF contains ammonium ion. Both solvents include protein substitutes; acetate is used in SLF, while amino acids are used in SUF. Both solvents include phosphate but the chelating agent diethylenetriaminepentaacetic acid (DTPA) is included in SUF to prevent possible formation of insoluble uranyl phosphate precipitates that would result in an underestimation of solubility. In addition to the above solvents, modified solvent compositions were prepared to investigate the role of specific salts in yellowcake dissolution studies. Solutions of SUF (Table 1) were prepared without DTPA (SUF-DTPA) and without amino acids (SUF-amino acids). No solution excluded both DTPA and amino acids. The SLF solutions were prepared with DTPA (SLF + DTPA) and without phosphate

Jan 1, 1981

By R. Berton, M. Walden, S. Melberg, N. Rocco

Recent tailings dam failures around the globe have influenced many mining industry regulators to reassess their requirements for the numerical modelling of tailings dam failures. This type or forward modelling is associated with overarching uncertainties as the model cannot be calibrated against a physical result. Dam breach analyses that meet the requirements of current industry standards and guidance typically begin with identification of credible failure modes and selection of appropriate topographic data set to represent the study area. The breach parameters and the volume of tailings released are then determined using available methodologies and empirical relationships. Subsequently, when the breach hydrograph is developed and the hydrology of stream networks are complete, the runout simulation is implemented. Due to the uncertainty involved in the process, sensitivity analyses are recommended to quantify variations in model inputs on the inundation extent and the flow characteristics. This paper outlines some common methodologies utilized for development of dam breach models, summarizes associated uncertainties with these methodologies and inputs, and provides guidance on how sensitivity analyses can address a wide array of uncertainties inherent in tailings breach analyses. This paper provides an understanding of how selecting appropriate breach parameters can result in reasonably conservative inundation extents consistent with the identified credible failure modes.

Mar 2, 2022

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By N. Damiano, C. Zhou, R. Jacksha, J. Srednicki

Modern electronic devices and systems used to enhance miner safety and health are becoming commonplace in underground coal mines. The ability for these devices and systems to function properly in the presence of electromagnetic emissions from other electronic and electrical devices and systems is not entirely understood. To investigate potential electromagnetic compatibility issues of critical mine electronic devices and systems, researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting surveys of electromagnetic emissions in underground coal mines. This paper presents the measurement system, methods, and results of electric field electromagnetic emission surveys conducted in three underground coal mine environments in the frequency range of 10 kHz to 1000 MHz. The survey data show that in some environments electric field electromagnetic emissions in underground coal mines approached or slightly exceeded limits as defined by other industrial sectors.

Mar 2, 2022

By T. Karalis

Perlite is a generic term for naturally occurring siliceous rock. It is a form of natural volcanic glass the main constituent of which is amorphous silica (70-76%). Perlite, when heated rapidly to its softening temperature range, expands from four to twenty times its original volume, due to the presence of 2-6% ?combined? water, in a manner similar to popcorn as the H2O molecules vaporize and create countless tiny bubbles, which account for its exceptional physical properties: light weight (30-150 kg/m3), low thermal conductivity, cellular structure, in general. These properties make perlite adaptable for numerous end-uses, which can be distinguished into 2 categories: Expanded perlite applications in: a) Construction Materials market (e.g. Acoustical Tiles, light-weight insulating Mortars, self-levelling Concrete), b) Agriculture (e.g. Hydroponics), c) Food and Chemical industry (e.g. Filtration Media, Filler, etc.), d) Insulation and Heat resistance technology (e.g. Cryogenic vessels, Refractory Bricks, etc.). Unexpanded Graded perlite applications in: a) Phosphoric Fertilizers industry (additive in H3PO4 production), b) Foundry technology (slag-aid, insulating and heat resistance agent).

Jan 1, 2006

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By Deepak Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet auditing can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1986

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Hydraulic transport is commonly used in mining for moving particles or ore concentrates in pipes over long distances with a water stream. Control and monitoring of this process require sensor technology that can obtain relevant characteristics of the two-phase flow. This work investigates the acoustic emission (AE) technology for monitoring a hydraulic system with different sand concentrations, showing the strong relationship between friction behavior in the pipe and the measured AE signals.

Apr 1, 2023