Search Documents

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By W. W. Dudley

The U.S. Geological Survey, in support of underground testing of nuclear explosives, has developed a technique (Dudley, 1910) to predict the inflow of ground water to large underground chambers that are cylindrical in shape. By treating the chamber as a large-diameter well pumped at constant drawdown, the nonsteady discharge can be computed by the method of Hantush (1961) for analyzing flowing wells under leaky artesian conditions. In mining applications, whether for mineral recovery or for nuclear testing, the most serious departure from the conditions of Hantush's model results from the gradual enlargement of the opening under drained conditions. Inherent in the analytical technique is that the "well" is fully completed at the time that dewatering begins. Because safety is the prime concern, however, initial pumping systems or personnel evacuation procedures must be designed to handle the greatest conceivable inflow. DEFINITIONS Because somewhat different meanings are attached to similar words in different technical fields, the U.S. Geological Survey definitions (Lohman, 1970) of several hydrologic terms used in this report are given below. An aquifer is a formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells, and springs. A confining bed is a body of material lying stratigraphically adjacent to one or more aquifers and having a hydraulic conductivity distinctly lower than that of the aquifer. The total head (dimensions L) of a liquid at a given point is the sum of three components: (1) elevation head, he, which is equal to the elevation of the point above a datum; (2) pressure head, hp, which is the height of a column of static water that can be supported by the static pressure at the point; and (3) velocity head, hv, which is the height the kinetic energy of the liquid is

Jan 1, 1971

By Swades Kumar Chaulya, Vikash Kumar, Sushma Kumari, Naresh Kumar, Girendra Mohan Prasad, Monika Choudhary

Opencast mines are vulnerable to inclement weather conditions as it disrupts the day-to-day activities at these mines. To address the problem, a perceptive driving assistant system (PDAS) has been developed to increase the visibility of real-time video of the road in front of the vehicle for operators of heavy earth-moving machinery (HEMM) at opencast mines in harsh weather conditions.

Apr 1, 2023

By J. S. Heath

Many disputes related to environmental issues in mining are resolved through often-antagonistic negotiations in a regulatory context or through litigation. These approaches are certainly the best choices for resolving certain disputes. However, just as no single remediation technology is the right fit for every site, so no single dispute resolution process is the best choice for every situation. This paper introduces a range of dispute resolution alternatives (from collaborative decision making through mediation, arbitration, and litigation). Especially when money is tightest, cost-effective dispute resolution(and the outcomes that can accompany it) can have an impact on the bottom line.

Jan 1, 2000

P.T. Freeport Indonesia's latest expansion has increased total mill throughput to 125,000 dry metric tonnes per day. The most recent expansion included the installation of a Semi Autogenous Mill designed to treat more ore than any other single SAG mill currently operating in the world. Also included in the expansion were two large ball mills, rougher and cleaner flotation including conventional and column cells and a regrind circuit. All equipment is supported by a modem distributed control system. This paper describes the design considerations, construction, commissioning and start-up of the SAG concentrator and support facilities and includes an overview of the oreflow and milling facilities.

Jan 1, 1996

By M. A. A. de Klaver

Due to the current cost and availability of crude oil in Brazil, Samarco Mineracao S. A., as part of its program of quality and productivity optimization and reduction of operating costs, has undertaken tests to utilize alternate energy sources for fuel oil used in its pelletizing plant at Point Ubu, Espirito Santo, Brazil. The energy program undertaken by Samarco consists of two basic steps. The first step was to reduce energy consumption, that is, to improve the thermal efficiency of the process. Secondly, a program was started to substitute the fuel oil with coal.

Jan 1, 1984

By G. Brackebusch, S. J. Jung

Backfilling techniques are widely used in large-scale underground mines. Massive pillars, which have been left in place for stability, limit mining activity. Backfilling allows safe recovery of the ore remaining in pillars and assures long term stability. In deep mines expected high stress can be relieved with the backfill. Initially, waste rock was used to fill the openings with mixed results. The need to improve safety and reduce costs has prompted the industry to investigate alternatives. Hydraulic filling with Portland cement added has shown considerable promise, but little has been done to define the parameters of design effective system. The purpose of this study is to determine the relationship between backfill and mining components that can be used to effectively design a best-case hydraulic backfill.

Jan 1, 2000

By M. Zuckerberg, E. Mader, R. Pasyar

We describe a new software product designed for the net present value optimization of multi-open-pit blended ore operations in which it is desired and/or necessary to dump some or all of the waste rock produced in the course of operations back into the voids created in the process of ore extraction. The software product simultaneously decides over the entire life-of-mine which material to mine in which year, once mined what to do with it, and where to put that material which it has decided to waste, all subject to annual blend and capacity constraints.

Jan 1, 2007

By Michael Li, Kathryn Rogers, Arie Moerman, Mike Cooper

The Brunswick Mine, a Division of Noranda Inc., produces zinc, lead, copper, and bulk lead-zinc concentrates through underground mining of a large massive sulphide deposit. The mining method employed is longhole open stoping with delayed backfilling. In 1996 Brunswick began a review of its mining methods and backfilling operations. In 1997 the decision was made to convert the backfill system from cemented and uncemented rockfill to paste backfill prepared from mill tailings. This paper will describe the features of the backfill preparation and distribution systems, review the handling of technical issues, and discuss experiences since plant commissioning.

Jan 1, 2001

By S. K. Samal, B. Mishra, M. K. Mohanty, S. C. Mishra

Steelmaking industries consume the majority of chromium and manganese ferroalloys to impart several properties in steel and also for other purposes. The quality of ore governs the process kinetics as well as the process economy of the ferroalloy industry. The present study demonstrates the thermal transformation behavior of chromite and manganese ores with varying compositions. Simultaneous thermal analysis (DTA/TG) is employed for such ore samples where the transformation of mineral phases is correlated with the thermogram characteristics and quantified. Phase, microstructure, and compositional analysis results of individual ores corroborated with thermal analysis are in good agreement. Chromite samples are ferruginous with goethite and gibbsite contents, whereas manganese ores vary in composition and also exhibit multiple and/or overlapping transformations.

Jan 21, 2021

By E. Tondu

Separation Technologies Inc.’s (STI) electrostatic separation technology is a dry, continuous process for the separation of discrete particles. This high-volume process does not require any additives nor is any additional waste produced. In December 1993, STI, in cooperation with New England Power(NEP), installed an 18-t/h (20-stph) prototype electrostatic separator at NEP’s Salem Harbor plant. The plan was to convert waste streams of type F fly ash into commercially valuable products. In July 1995, a second separator was installed at NEP’s Brayton Pointplant. Fly ash feed, ranging from 6% to 25% carbon (loss-of-ignition fly ash or LOI), is separated into <3% LOI “clean” ash and sold as a portland cement substitute in the New England concrete markets.

Jan 1, 1996

The National Mining Association’s (NMA)MINExpo International ’96 is shaping up to be the organization’s largest. About 30,000 mining industry business and technical professionals are expected to descend on Las Vegas, NV Sept. 9-12 to take part in the 25 technical sessions and visit the more than 900 exhibitors who will be showing off their products and services. MINExpo will be the largest mining equipment and services exposition in the United States this year. Exhibits at MINExpo will fill the Las Vegas Convention Center, parking lots and part of the Hilton Center, located next door to the convention center. NMA estimates that this year’s show will cover more than 46,450m2 (500,000 sq ft) of exhibit space. Some of the exhibits on display will include haultrucks, hydraulic shovels and excavators, conveyors, continuous miners and tunneling machines. In addition, an array of computer equipment and software will be demonstrated. A new feature this year will be a helicopter pavilion, located in the Hilton Center. Helicopters and fixed-wing aircraft have become indispensable to many remote mining operations. NMA said that at least one full-size helicopter will be on display.

Jan 1, 1996

By Zhongran Dai, Nan Hu, Jianhong Ma, Hui Zhang, Zhihua Zhong, Han Zhou, Feng Li, Yonggen Qiu, Yang Ding, Yingchun Yang, Dexin Ding

In the traditional chlorination roasting-water leaching-solvent extraction process for the extraction of rubidium-bearing ore, Rb leaching from the ore and calcium removing from the leachate are conducted separately, and this results in the complicated process and high energy consumption. In order to integrate the Rb leaching and calcium removing processes, Rb-bearing polymetallic ore was firstly treated by chlorination roasting, it was then leached in a micro-reactor with raffinate, and the calcium ions in the leachate were removed in the reactor as carbonate precipitates by passing CO2 at certain pressure into the reactor. The effects of raffinate alkalinity, CO2 pressure, and CO2 reaction time on Rb leaching rate and calcium removing rate were investigated. The experimental results show that when Rb-bearing polymetallic ore was leached for 90 min by stirring with raffinate with 1.125-mol/L alkalinity, and the pulp was made to react with CO2 at 0.8 MPa for 15 min, the Rb leaching rate and calcium removing rate amounted to 92% and 98.2%, respectively. This integrated process including Rb leaching from Rb-bearing polymetallic ore and calcium removing from leachate could simplify the process for the extraction of Rb-bearing ore and increase its economic benefits.

Sep 27, 2023

By John F. Oyler

The performance of high alumina refractory subjected to high compressive loads and high temperatures is an area in which operating experience is quite limited. This paper documents the results of five months of operation of a combustion chamber lined with 83 pct alumina brick subjected to compressive stresses as high as 45psi and hot face temperatures of about 2750°F. It also describes a method for predicting long term subsidence results based on the limited information available in standard hot load limit tests. Descriptions of the chamber itself and the pilot plant upon which its design was based are included.

Jan 1, 1978

By M. Sears, W. H. Su, J. Wickline, M. A. Van Dyke, G. Esterhuizen, Z. Khademian

It is commonly recognized that seismicity can be induced by rock failures or slip along geologic structures around mining excavations. The unpredictable nature of these events and their proximity to the working area may raise safety concerns in underground mining operations. Modeling can be a useful tool for estimating seismic potential for a given mine layout, but the challenge is to detect a seismic event and estimate its intensity in the model. One well-documented approach is to monitor the variation in the energy content of the model and record potentially damaging seismic events when there is a significant release of energy. Researchers from the National Institute for Occupational Safety and Health (NIOSH) employed this approach using 3DEC modeling software to simulate the anomalous seismic events that occurred in a deep longwall mine in Virginia in 2005. A four-panel model of the mine was constructed utilizing a 2D cross section at the location of the mining face at the time of the event. Seismic potentials associated with the development of each panel are evaluated by recording the seismic energy released during the simulation. The results demonstrate the occurrence of two relatively significant events during the mining of the last panel, which are consistent with the historical observations at the mine.

Apr 26, 2022

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos using the Unity game engine. The simulation videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories using graphic simulation. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Jun 1, 2023

By James L. McGregor

St. Joseph Lead Company has been paying incentive bonuses for well over 40 years. In 1958 almost half of St. Joe&apos;s 1,860 employees in Southeast Missouri received some form of incentive bonus in addition to their guaranteed wages. There are very few payroll jobs in St. Joe s Southeast Missouri organization that lend themselves to a reasonably good measurement of production or quality, or both, where an incentive bonus is not paid. The term "Incentive Bonus" is used to differentiate betwen bonuses that are based on quantity or quality of work, and those that are merely additional pay of a standard amount per hour or day because of an employee being temporarily assigned to some unusual task, An employee temporarily assigned to a job where the working conditions make the job performance unusually difficult or where a special skill is used is often given a bonus of some standard amount per hour or shift in addition to his usual rate. This is merely a convenient way of paying something extra without disturbing the normal rate structure. Actually, it is differential pay similar to that almost universally paid for evening and night shift work. Bonuses of that type are not being considered in this paper. The basic reason or theory for paying incentive bonuses 9s to get improved production at lower cost, Unfortunately, it is often difficult, if not impossible, to find a yardstick by which it can be definitely proved that a particular bonus plan is accomplishing its purpose, It becomes, then, a matter of judgment on the part of management personnel as to the value of the bonus plan. The fact that St. Joe Lead Company has continued to pay bonuses for over 40 yews and has increased the number of bonus schedules used attests to a definite belief that they are beneficial to the company&apos;s successful operations.

Jan 1, 1960

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By Charles Banks Belt

In 1925, Niggli (1925, pp, 1-69), formulated a physico-chemical, explanation for the origin of hydrothermal ore deposits, from a concept that had appeared earlier in the literature in the writings of Von Groddeck, Stelzner, Beck, de Launay, Kemp, and Lindgren. Niggli proposed that pressure at depth could force volatiles from deep-seated magmas. The volatiles would In turn form pegmatites and then ore deposits as the fluids cooled. This is one view of a general theory of ore genesis that gained secondancy for years among such prominent geologists as Fenner (1926, p, 697) and Emmons (1936, pp. 29-70). It was, proposed that ore deposits were precipitated from solutions or fluids that had escaped or been separated from a deep-seated magma by means of liquid immiscibility or crystallization or gas transfer. This theory is based on the presence of igneous rocks close in space and age to hydrothermal ore deposits in many mining districts of the world. As is well known, there are many ore deposits apparently of hydrothermal origin that are neither spatially nor chronologically related to igneous rocks, In still other localities where there are no hydrothermal ore deposits, igneous rocks occur that are similar in composition to those in mining districts. In view of such facts, the applicability of the Niggli theory to all hydrothermal ore deposits may well be questioned. The chief purpose of this paper is to test the Niggli theory by studying the primary petrology, hydrothermal alteration, and distribution of copper and zinc in silicic igneous plutons supposedly genetically related (in the Niggli sense) to nearby hydrothermal ore deposits, Silicic Tertiary plutons in three New Mexico mining districts were chosen, the Hanover-Fierro intrusive at Hanover and Fierro, the Granite Mountain pluton at Magdalena, and the four outliers of the Lordsburg stock at Lordsburg. First, it had to be established whether the observed plutons were or were not the source of the adjacent ore deposits. This was done by studying the relation between the copper or zinc distribution-and the primary or secondary features in the plutons studied, and the time relations between instrusion and ore deposition. Primary igneous features of a pluton are defined as the minerals, texture, shape, and character of the pluton which were formed prior to the complete solidification of the rock, secondary features include all changes that took place in a pluton after solidification. They are identified by their cross cutting nature or as replacing primary minerals, Under the Niggli concept, it is proved that the ore ions did not originate from the parts of the pluton now visible as immediately adjacent to the ore deposits; it must then be established, if possible&apos;, that the ore ions were separated from deeper parts of the intrusive, Some idea as to whether the copper or zinc ions originated from a related magma at depth may be gained by a comparison between the primary (that is, pre-alteration) zinc and copper abundances found in ore localizing intrusive studied and the average abundances for copper and zinc in silicic igneous rocks most recently given in the literature. Finally, the relation between ore deposition and hydrothermal alteration was studied on a regional as well as on a local scale.

Jan 1, 1958

By R. Wensel

A composite material consists of two or more dissimilar components. These dissimilar components retain their identities when mixed together and contribute to the properties of the composite. A composite usually consists of two parts, the matrix and the reinforcing material, or extender that is added to the matrix. Typical materials used as the matrix in composites are metals, polymers, and ceramics. The reinforcing material can be added for any number of reasons. For instance, if the matrix is expensive, an inexpensive filler may be added to the matrix to lower the cost of the product without sacrificing properties. An example of this is calcite (CaC03) which is added to systems such as polyvinyl chloride (PVC), to lower the cost. Reinforcements may also serve as a means to enhance the properties of the matrix material. For example, carbon fibers are frequently added to plastics to increase their strength, and glass spheres may be added to plastics to improve flexural strength. Mg(OH)z is added to polymers to give the property of fire retardancy. The latter is the focus of this paper.

Jan 1, 1995