Search Documents

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By R. J. Gray

Oxidation of coal can best be described as a process of deterioration, since most of the uses of coal, such as for fuel and by-product chemical and coke production, are adversely affected by coal oxidation, and the inclusion of oxidized coal in most coal products detracts from their value. There are probably many mechanisms of coal oxidation, and the ways oxygen molecules combine as complexes with coal macromolecules to form new substances have been dealt with and speculated upon by many workers1)* but are not dealt with in the present work. This study deals with tests and methods of detecting oxidized coal, with particular emphasis on the microscopically discernible changes that accompany the chemical and physical changes that affect the technological properties of coal during oxidation.

Jan 1, 1974

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By Paul C. Lingo

The title of my talk today might lead you to two logical conclusions: The industry is faced with a problem that requires a solution and after discussing the problem I will offer a solution. The first conclusion is painfully accurate. One need only look at the accident statistics to be aware of the problem. During the eight-year period 1954 through 1962, the United States Bureau of Mines reports that falls of rock and coal accounted for 1,435 of the 2,516 fatal injuries that occurred in underground bituminous coal mines. Some improvement was made during 1962. For the first time since records have been kept, falls of rock and coal accounted for less than 50 per cent of the underground fatal injuries. The 105 deaths recorded in 1962 indicate that a great amount of work remains to be done in this area. As to the second conclusion, let me assure you at the outset that I have no panacean solution; however, I do propose to discuss some aspects of the problem and some possible methods of solution. What methods of solution are now, or have been employed in attempting to solve the problem? More specifically, what methods have you and your associates used? Has it been an orderly well thought out approach to the entire problem, or has it been a somewhat piecemeal approach which tackled the immediate problem and left the total problem for another day? Perhaps a new approach may be in order.

Jan 1, 1964

By M. K. Mohanty

A modified coal flotation characterization procedure, referred to as the Advanced Flotation Washability (AFW) technique, has been developed which, compared to traditional procedures, provides a more accurate prediction of the optimum separation performance achievable by a froth flotation process. The AFW procedure uses a vertically-baffled flotation column which provides enhanced selectivity among particles of varying degrees of hydrophobicity due to a plug-flow environment and an improved carrying-capacity environment. In fact, the separation performance of the traditional procedures was enhanced by increasing the possibility of operating under improved selectivity conditions. The separation performance provided by the AFW procedure was superior to that obtained from multiple cleaning stages using commercially-available flotation columns under both kinetic and carrying-capacity limiting conditions.

Jan 1, 1997

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By Adrian C. Dorenfeld

[Agitation and transport of slurries have been investigated intensively for the past twenty years. It has been shown (1) that slurries have the properties summarized in Figs. 1, 2, 3, 4, and S. For a detailed exposition the reader is referred to the above reference and the bibliography, which, in turn, have extensive references and bibliographies. An interesting problem with which the senior author has been concerned with is the scab up of power requirements for slurry agitators operating in the laminar region with pseudo plastic materials. Pulps of shaly ores, after various chemical reactions in aqueous leaching systems, are often difficult to settle and filter if agitation is violent. In these cases agitation must be at a minimum, yet prevent [tling] such as in copper uranium ores. This mild agitation is on the laminar region.]

Jan 1, 1967

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By W. A. Haley

Wheel loaders became important bulk materials handling tools in the early fifties. As they grew in stature, productivity, reliability, and acceptance, the demand for larger, more rugged machines evolved. In the early sixties, the introduction of a 6-yard model by a major equipment manufacturer led quickly to widespread experimenting and rapid worldwide acceptance in loading blasted rock in stone quarries and smaller metal mines. As the wheel loaders grew in popularity for shot rock loading, larger models, 12- to 15-yard size were developed and saw widespread use by 1970. In the past 20 years, at most quarries and small to medium size mines, most cable operated power shovels have been replaced by large wheel loaders and more recently, hydraulic excavators as the primary loading tool. Wheel loaders larger than the 15-yard class are not used widely. Until about 1970, very few overburden haulage trucks were used in domestic coal mines. About that time, many states started enforcing stringent mine relcamation regulations and in 1977, even more stringent federal legislation was passed. These controls brought about drastic changes in coal surface mining methods in the mountainous areas of Appalachia, in smaller midwestern mines and in the large mines of the western states. Basically, simple material casting methods were replaced at most eastern mines by "haul-back" and "mountain top mining" methods using controlled placement of overburden as it is removed from the coal. These methods dictated much more extensive use of loaders/ shovels and trucks to the point that most coal mining in those areas is now by loader/shovel trucks methods. And those areas have become the home of the country's largest population of large wheel loaders and trucks in the 35- to 85-ton size class with a trend to even larger trucks and shovels. To maintain equal production or provide for growth, the new methods have caused a sharp increase in machine intensity to the extent that at some mines, up to three times as many machines were required to mine a million tons of coal in the late seventies as compared to the machine needs in the sixties. Mining costs and coal prices also took a big jump in the mid-seventies, paralleling the drastic price increases in oil and other forms of energy.

Jan 1, 1984

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

By H. E. Hawkes

Reconnaissance mineral exploration based on the distribution of ore metals in stream sediments has become a generally accepted method of mineral reconnaissance. This approach seems to work almost equally well in all climates and in all kinds of terrain, provided of course that the ore deposits being sought are exposed at or near the surface and are actively undergoing erosion. Nobody with any experience in the field would question the validity of the concept on which stream sediment reconnaissance is based. Considerable dispute does arise, however, when the subject of density of sample sites per unit area, or sample spacing, comes up for discussion. What is the optimum balance between completeness of coverage and cost? The tacit assumption is frequently made that a greater sample density necessarily leads to more complete coverage and hence a lower probability of missing an important discovery, without regard for the size of the stream sample or the topology of the drainage pattern. The purpose of this paper is to attempt to bring the problem of site selection in stream sediment sampling into better focus, and to present a formula that may help in planning reconnaissance programs.

Jan 1, 1976

By R. C. Emmett

In extractive metallurgy, separation of insoluble solids from solutions is an important economic factor in almost all flow- sheets. This separation step can employ sedimentation, filtration (vacuum and pressure), or centrifugation. Since practically all systems require a relatively complete separation, multiple unit, countercurrent thickeners or vacuum filters are generally used.

Jan 1, 1974

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By D. A. Longhurst

Improper size distribution of the grinding media in a multicompartment mill can be a source of many operation problems encountered. Inefficient use of the power expended for grinding, and an undesirable product size distribution are two frequent resultants. It is necessary to resize the grinding media in the leading mill compartment at time intervals related to the abrasive nature of the material being processed. In practice, this is done when time permits and with sketchy guidelines, if any. Maintenance of the grinding media size distribution can be scheduled, and would be, with a realistic method supplied to the user.

Jan 1, 1984

By R. Casagrande, L. R. Moore, J. Sessoms, P. Macy

"A South American nickel mine has been producing a nickel concentrate that also contains copper and iron (15 percent nickel, 5 percent copper, 28 percent iron) for the end use of stainless steel production. A critical specification for the quality of the steel is the iron to magnesium oxide ratio (Fe:MgO), with a ratio of below 3.5:1 having a substantial impact on the nickel value. This nickel concentrate producer historically mined the sulfur-rich mineral pyroxenite but had been forced to move to a magnesium oxide/silicate (MgO/SiO4)-rich mineral harzburgite, resulting in nickel recovery being reduced to around 50 percent to maintain the required Fe:MgO ratio. In this study, ore mineralogy, water chemistry and the chemistries associated with the flotation process were evaluated in an effort to increase nickel recovery while maintaining the Fe:MgO ratio according to specification. New chemistry was introduced with the specific goal of complexing with the MgO and retarding its interaction with the bubble flow in the flotation process.IntroductionGlobal nickel production in 2011 totalled to 1,770,000 tons, according to the Raw Materials Group (2013). From 1950 to 2005 there was an aggregate 4.4 percent increase in nickel production, with a market-value high of $1,000/ton nickel reached in 1998 (Mudd, 2010). Approximately 65 percent of nickel production is consumed by the stainless steel industry, with 12 percent of the remainder used in super alloys or nonferrous alloys. Nickel imparts corrosion resistance, temperature resistance and other benefits to its alloys (Table 1) (Oberg, 1996; Cáceres, 2003). The dominant types of nickel-bearing ores are classified as either laterites (limonite: nickel-iron oxide; and garnierite: nickel hydrosilicate) or magmatic sulfide deposits (pentlandite: iron-nickel sulfide) (U.S. Geological Survey, 2013a, 2013b). In 2012, about 40 percent of the nickel ore mined was sulfidic-type ores and about 60 percent was laterite. The processing of laterite ore is expected to continue to increase as the availability of sulfidic ores continues to decline."

Jan 1, 2015

By Kewal K. Kohli, Richard E. Thill, Syd S. Peng

The results of unpublished investigations into surface subsidence from coal mining in the Northern Appalachian Coalfield are summarized. These investigations were carried out by various coal companies and the State of Pennsylvania in the sixties and seventies. Subsidence data were collected and analyzed from 10 room-and-pillar panels in 5 mines in the Pittsburgh coal seam. Results show that angle of draw ranges from 26° to 33° and subsidence factor from 0.42 to 0.72; surface heating generally occurs beyond the edges of the panel, the amount and extent of which vary; waviness occurs in the subsidence profile if a substantial number of pillar stumps are left in irregular patterns; interpanel effect is significant; time-dependent subsidence exists, but varies for different panels; and surface slope does not seem to affect the amount of subsidence.

Jan 1, 1982

By J. K. Hrica, T. J. Orr, J. Navoyski, B. Macdonald, C. L. Hoebbel, J. L. Bellanca, B. Demich

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos. The videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Feb 1, 2023