Search Documents

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By Herbert H. Einstein

Swelling ground is one of the most feared problem in tunneling. Although usually not causing sudden failures during construction, the very large and long- lasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners of up to 1 m that have been cracked or crushed, tunnel inverts that are heaving at a rate of 0.1 m per week during construction and continue to heave during decades. This author (Einstein (1979). Einstein et al. (1972) (1975)) and others (Huller (19761, Grob (1972) (1976). Golta (1967), tienke (19761, Krause (1976). Lee et al. (1976)) have described many cases of swelling tunnels that illustrate the significance and magnitude of the problem. This paper intends to show that tunnels in swelling rock can be built to perform satisfactorily. . For this purpose the tunnel builder needs to know how to determine the existence and specific behavior of swelling ground, how to select appropriate structural characteristics of the tunnel and predict its performance under the specific ground conditions, and finally how to construct the tunnel such that the anticipated performance will be achieved. This concept of a design-construction procedure is the same as that for tunneling in general; it is mentioned here for NO reasons: 1. To point out that design and construction cannot and should not be separated. The way in which the tunnel will be built has to be an integral part of the design. 2. This paper will be structured corresponding to the procedural concept.

Jan 1, 1981

By Daniel A. Wasson

A review of the history of boosters is given with examples of the prominent types that have been made commercially. The performance and design features of protected core boosters are discussed in detail. A new gel booster is discussed with its advantages to the mining industry. Booster size, hole configuration, performance and safety aspects are reviewed. Important features of boostering in above ground and underground blasting are related to an economic analysis. This presentation will cover different types of boosters commonly used in mining. However, for the purpose of this paper a few terms need to be defined to clarify the action of different parts of a priming system. Booster* - "Any unit of explosive or blasting agent to be used in a charged hole for the purpose of perpetuating or intensifying the initial detonation". Primer* - "A unit, package or cartridge' of explosives containing a detonator or detonating cord which is used to transmit detonation to other explosives or blasting agents". Detonator - A device for initiating a detonation from a flame or a small electric current, the former being represented by a fuse cap and the latter an electric blasting cap.

Jan 1, 1981

By R. Bokotko, J. D. Miller, J. Hupka

Laboratory results from an initial study on the removal of SO2 from gas mixtures are reported using air-sparged hydrocyclone (ASH) technology. Tap water and alkaline solutions were used for absorption and the influence of gas flow rate, water flow rate and length of the ASH unit were investigated. Complete removal of SO2 was possible with very favorable kinetics. The efficiency of sulfur dioxide absorption from air using the ASH is compared with the efficiency of conventional technology.

Jan 1, 2002

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By M. C. Roberts

Currently, mineral producers are suffering through a major downturn in prices for their products, even though it has only been a few years since they were enjoying high prices. From an historical perspective, the current situation is another of the cyclical down-turns that often reoccur every 5 to 7 years or so. This paper uses time trend decomposition techniques to identify the cycles and statistical methods to find the duration of these cycles for a variety of mineral prices. Given some idea of how long and severe these cycles typically are, the mining industry can better plan to weather the downturns and take advantage of the upturns. For example, timing investments in new projects to take advantage of the cyclical upturns can dramatically improve project profitability.

Jan 1, 2000

By Steve Kral

President Bush’s National Energy Program and his Clear Skies Initiative both emphasize the use of coal to help meet the nation’s growing energy needs. And why not? Coal is currently responsible for more than 50 percent of the nation’s electricity generation. That fact, though, seems to be lost on policy makers, the environmental community and the public. Critics of coal advocate the increased use of renewable energy sources and the increased use of natural gas. Renewables, though, are only capable of generating a tiny fraction of the power required. Natural gas is expensive. And natural gas production cannot keep up with demand, especially given the nation’s increasing energy needs.

Jan 1, 2003

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

By W. Dan Hausel

More than 220,000 diamonds have been found in the United States that range from microdiamonds to 40.42 carats in weight (Table 1). Some reports suggest diamonds weighing more than 100 carats have also been found in this country, although these reports have not been verified. The source of most of the diamonds in the United States is a group of kimberlite pipes, dikes and blows in the Colorado-Wyoming State Line district and a group of lamproite pipes in the Murfreesburo, AR area. Other areas where diamonds have been found include the Great Lakes region, the Pacific Coast and the southern Appalachian Mountains. The latter two regions are generally not considered favorable for diamond deposits. This is based on exploration models. They suggest commercial diamond deposits will be restricted to kimberlites emplaced in Archean cratons and to lamproites emplaced in Proterozoic mobile belts accreted to the cratons.

Jan 1, 1995

By J. T. Tanner

The research activities of the Minerals Research Laboratory, which is a part of North Carolina State University, is normally confined to solving beneficiation problems, and developing flotation processes for the mining industry. In recent years the laboratory has veered from its main purpose somewhat and has placed some emphasis on the manufacture of products from mineral concentrates. This has been the result of requests for help from industry. One such request came to the MRL from a talc producer in North Carolina who was having a difficult time competing with foreign imports of steel marking crayons. He felt that if a process could be developed whereby a satisfactory crayon could be produced from powdered talc at a low cost that he could compete.

Jan 1, 1986

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits, thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium. Key Words: Rhenium, Ammonium Perrhenate, Extractive Metallurgy

Feb 27, 2013

By Jonathan G. Price

Silver-copper-lead deposlts in Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore In overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulfide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1983

By G. Nash

Despite further declines in production for some producers, 1986 proved to be a landmark year for the asbestos industry. The key event was the adoption of The Asbestos Convention by the Inter- national Labour Organization (ILO) and its 150 member countries. The document, entitled "Safety in the Use of Asbestos", reaffirms the international consensus on the "controlled-use" approach to chrysotile asbestos regulation. The decision of the ILO has come at a critical point in time. It represents a major turning point and provides an important building block for the long term future of the asbestos industry.

Jan 1, 1987

The Golden Grove Project area is located 220 km (137 miles) east of Geraldton in Western Australia (Fig. 1). The project is a joint venture involving Amax Exploration (Australia) Inc. (Amax), Electrolytic Zinc Co. of Australasia Ltd. (EZ), and Esso Exploration & Production Australia Inc. (Esso), each with 31 116% interest, and Aztec Exploration Pty., Ltd. (Aztec), with a 3 1/2% carried and a 3% contributing interest. The venture covers two significant volcanogenic massive sulfide deposits and some 40 km (25 miles) of highly prospective Archean volcanics. During the course of the past 12 years (to 1983), all four companies were responsible for operating the project at one time or another and all influenced the discoveries. The Gossan Hill and Scuddles deposits are typical examples of volcanogenic massive sulfide deposits associated with Archean explosive submarine acid to intermediate volcanic complexes. They are located in the northwesterly trending Yalgoo greenstone belt of the West Australian Archean Shield. Gossan Hill, located in 1972, is essentially a copper deposit with minor zinc lenses; to date, 97 diamond holes have delineated a geological resource* estimated to contain 13 Mt (14.3 million st) of of 3.4% Cu and 13 g/t (0.38 oz per ton) Ag in the main lenses with minor lenses totaling 2 Mt (2.2 million st) of 3.7% Cu and 17 g/t (0.49 oz per ton) Ag and 1.7 Mt (1.9 million st) grading 1.5% Pb, 14% Zn, and 87 g/t (2.8 oz per ton) Ag. Scuddles is a zinc-copper deposit with gold and silver credits. It *Resource estimate provided by Esso for inclusion in Aztec Exploration Pty. Ltd. 1982 Annual Report was discovered in 1979 and, to the end of 198 1, had been delineated with 42 diamond holes. On the basis of this drilling, a geological resource* of 26 Mt (28.7 million st) has been estimated in three coalescing lenses. The lenses comprise 7.5 Mt (8.3 million st) of 2.1 % Cu, 12 g/t (0.35 oz per ton) Ag, and 0.3 g/t (0.009 oz per ton) Au; 7.6 Mt (8.4 million st) of 0.4% Cu, 9.9% Zn, 73 g/t (2.3 oz per ton) Ag, and 0.7 g/t (0.02 oz per ton) Au; and 1 1.0 Mt (1 2.1 mil lion st) of 1.1 % Cu, 9.3% Zn, 8 1 g/t (2.6 oz per ton) Ag, and 1.5 g/t (0.044 oz per ton) Au. Readers are referred to Frater (1978) and Harris et a). (1982) for a more detailed geological account of these deposits.

Jan 1, 1991

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

Minerals are fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels?mining, processing and manufacturing finished products. The estimated growth rate for the real GDP of the United States was 2.1 percent and the nominal GDP was about $13.8 trillion in 2007 (Table 1). The prime interest rate decreased to 7.25 percent in December from 8.25 percent at the beginning of 2007, reflecting actions taken by the Federal Reserve Board to counter financial difficulties surrounding subprime mort-gages. Delinquencies on subprime mortgages increased throughout the year, affecting not only the delinquent home owners but also financial instruments invested in mortgage-backed securities. The average contract mortgage rate for the purchase of previously occupied homes in the United States was 6.35 percent in November; a slight decrease from 6.37 percent in January but still greater than 5.34 percent reported in July 2003, the lowest rate in the past five years. With the tightening of credit, the seasonally adjusted annualized rate for new privately owned housing starts declined 27 percent from December 2006 to November 2007. The loss in the residential market was balanced by a 9-percent increase in nonresidential construction between January and August 2007, during which slight increases occurred in nearly all

Jan 1, 2008

By K. S. Liddell

Ultra fine grinding is becoming increasingly used in the mining industry over recent years. The development of large-scale units for high volume grinding of low value materials and concentrates has opened up new areas of economical metal extraction. The ability of stirred vertical mills to produce very fine particles with high surface areas, is providing mine operators with novel extraction possibilities within gold concentrate regrind for Biox or leach feed, Activox autoclave feed preparation and lime slaking operations. The paper will review design, operational and maintenance aspects of ANI-Metprotech stirred vertical mills, comparing these to tower mills, horizontal bead mills and attrition mills.

Jan 1, 2001

By S. Yerel

In a mineral processing plant, the determination of a preventive maintenance schedule is one of the most important maintenance policies. In this study, to determine the preventive maintenance schedule for the Emet Colemanite Mineral Processing Plant in Turkey, a mean quality control chart was constructed using the historical concentrate B2O3 grade data. The effect of preventive maintenance scheduling on B2O3 grades was monitored using the mean quality control chart. It was determined that recovery increased after each preventive maintenance scheduling. Close examination of the mean quality control charts indicated that there were three periods that showed different grade characteristics. These were identified as the period ?prior to preventive maintenance,? the period ?after preventive maintenance? and the period ?requiring preventive maintenance.? These periods were compared as two independent samples by using the Kolmogorov-Smirnov test. Application of this test for interpretation of the mean quality control chart enabled the authors to analyze the system effectively, and it showed that the preventive maintenance for this plant should be scheduled at four-month intervals.

Jan 1, 2007