Search Documents

By Frank J. Wiebelt

The Mohawk lead-zinc mining in San Bernardino County, Calif., was examined by D. W. Butnor, an engineer or the Bureau of Mines, at the request of Dunton, Ray, and Greenwood, leaseholders. Current operations were on a marginal economic basis, and government aid was sought in an endeavor to outline ore reserves so that production might be maintained.

Jan 1, 1949

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By George F. Dana

Oil yields, lithology, and stratigraphy have been evaluated for 15 cored wells and two sampled wells representing 10 square miles of the Tipton Member of the Green River Formation near Green River, Wyo. The area evaluated is being used by the Bureau of Mines for experimental production of oil from the oil shales in place. Lithology and oil yields were correlated to produce a stratigraphy diagram for the in situ study area, permitting precise designation of comparable sections. Because of lateral uniformity of oil shale, oil yields from eight cores and two sets of drill-cutting samples within a quarter section show the range of variation in average oil yield arising from experimental error. Variation in average oil yields from the seven cores representing the 10-square-mile study area lies within the expected experimental error. No difference in oil-shale richness across the study area is indicated. Average oil yields for three Tipton sections in the study area were deter-mined as follows: (1) The entire Tipton Member oil shale (about 145 feet thick), 13.3 gallons per ton; (2) the 40-foot upper rich zone, 21.0 gallons per ton; and (3) the 21-foot zone in which the Laramie Energy Research Center is conducting in situ experiments, 22.4 gallons per ton. One acre of the 21-foot experimental section represents 34,300 barrels of oil in place, and 1 acre of the Tipton's 40-foot rich upper layer represents 62,000 barrels.

Jan 1, 1972

By John B. Gayle

The probable inadequacy of physical tests of coke for the purposes for which they are made has been a subject for discussion for many years. However, little has been published in this connection, even though most workers in the field believe that the physical properties of coke are of major importance in its utilization in the steel and allied industries. In fact, the reproducibility of the recognized tests is largely unknown or can only be approximated. This situation occasions many difficulties when attempts are made to judge the coke-production qualities of various coals or coal blends. During World War II the Coke Production Committee, composed of representatives from industry and the Solid Fuels Administration, concluded that study of existing testing methods and possible improvements would be of material assistance in answering questions relating to coke quality. Since that time the Bureau of Mines has taken samples of coke produced in industrial slot-type coke ovens in connection with studies aimed at extending coking-coal reserves by adding to the list of sources known to be suitable for this purpose. Testing procedures on these cokes were arranged so that the data obtained would yield information on (1) the degree of precision of tests commonly used in the industry, (2) the causes of the known poor reproducibility in several of the physical tests, and (3) possible improvements or modifications of existing physical testing procedures.

Jan 1, 1953

The U.S. Bureau of Mines (USBM) has developed a test procedure to compare the initiating strength of detonators by using adjustable-sensitivity liquid explosives. Various tests of detonator strength are currently used by the industry, but many of them do not quantify the ability of detonators to initiate detonation reactions in an explosive charge. The USBM used mixtures of nitromethane and ethylene diamine, the sensitivity being "fine-tuned" by 2-nitropropane. Military standard J-2, commercial No.6, and commercial No.8 detonators were evaluated using three test configurations: (1) axially immersed in the test explosive, (2) tip just touching surface of the explosive, and (3) immersed transversely in the explosive. Markedly different results were obtained for these three configurations, indicating that the directional effects are important. This explains why different detonator strength tests do not correlate well with each other. Some tests, such as the sand bomb and underwater, measure the total energy out-put, while other tests, such as the plate dent, test measure the energy in the axial direction. The USBM's test data indicate the importance of conducting the experimentation in the manner in which the detonator is actually intended to function.

Jan 1, 2010

By E. J. Schneider

In view of the growing commercial interest In the higher boiling fractions of low-temperature tar, a study of the literature has been undertaken to obtain as many data as possible regarding the properties of possible pure constituents. The following substances have been studied: THREE-ORTHO-XYLENOL (1, 2-DIMETHYL-3-HYDROXYBENZENE) Detection By the isolation of the silver salt of 1, 2-dimethyl-3-phenoxyacetic acid.

Jan 1, 1930

More gold is being produced now than ever before in recorded history. All over the world huge quantities of ore are being mined and processed, thanks to historically high prices for gold and the use of processing techniques demonstrated as cost efficient in the last 20 years. Over the past 10-15 years prices for many other metals have been depressed, and gold has accounted for a significant proportion of worldwide exploration and development expenditures(l)1. The revenues generated from gold mining are providing greater return on investment, more jobs, and more tax revenues to national governments than ever before. Emerging nations are using the gold industry as a springboard for development; developed nations are continuing to fuel their economies with gold industry revenues; and China and countries of the former Soviet Union are using the gold industry to generate foreign exchange, modernize their mining industries, and take the first tentative steps toward private sector participation in their economies.

Jan 1, 1994

To design an apparatus that advances the state of the art in gas content testing equipment. The goal of the design is to incorporate improvements in testing sensitivity/accuracy, durability, and ease of operation over existing equipment. It is also desirable for the new design to successfully perform gas content determinations of multiple chemical species from a rock sample.

Jan 1, 1999

By Joseph J. Wallace

1. The Pittsburgh is the most important bed in Washington County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 4,181 million short tons as of January 1, 1954. Of this total, 4,132 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By Irving Hartmann

The record of safety in the use of permissible explosives in United States coal mines has been excellent, due in great measure to the persistence with which research has been carried on in the Bureau of Mines, to the development of permissible explosives, and to the cooperation of mine operators and workers in using permissibles in a recommended manner and in the effective though gradual replacement of black powder and other nonpermissibles. The demand for increased rate of coal production, changes in mining conditions and minim methods, and introduction of new mining machinery have resulted in modified or new blasting practices. To keep abreast of these developments the Bureau of Mines conducts investigations under actual mining conditions at the Experimental coal mine near Pittsburgh, Pa. Several years ago an extensive study was complete to determine conditions under which the allowable charge limit for permissible explosives per shot hole might be raised from 1.5 to 3 pounds without undue risk of gas or coal-dust ignitions. As a result of the study, this increase in the charge limit was authorized under certain specified conditions in 1948,5/ greatly facilitating production schedules.

Jan 1, 1954

By Charles B. Kenahan

The effects of ultrasonic radiation on the electrodeposition of copper-zinc, copper-cadmium, and copper-tin alloys from cyanide baths were investigated by the Bureau of Mines at frequencies of 18.5 and 38 kilocycles per second, and at acoustic intensities up to 0.5 watt per cm3. Significant changes occurred in the composition of the deposited alloys; some of these deposits were brighter, harder, more adherent, or of finer grain size than nonirradiated deposits. The irradiated deposits were also smoother and less porous, and they afforded better corrosion protection for the substrate metal in sodium chloride solution. The limiting current densities of the cyanide baths were increased by the application of ultrasonics. Anode and cathode current efficiencies also were increased, and cell voltages were lowered; the relationship of these effects to current density is discussed. Electrode potential measurements showed significant depolarization effects at both electrodes during ultrasonic irradiation. The resulting decrease in cell voltage was due chiefly to depolarization at the anode, and the anode became less passive.

Jan 1, 1967

By Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2007

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960

By L. J. Froisland

Water classification and heavy-media sink-float methods were investigated for concentrating metallic junk automobile shredder rejects initially upgraded to about 75-percent metal content in an air elutriation system. An 8-inch-diameter water elutriation column with a feed capacity of 2.7 tons per hour was constructed and operated. The results obtained were compared with those produced by sink-float methods. Tests made on duplicate samples of an intermediate-grade metal product were successful in upgrading the metal con-tent from 75 percent to 98.7 and 99.1 percent with respective recoveries of 95.5 and 98.9 percent for the water classification and sink-float procedures. Tentative flowsheets for treating junk auto shredder rejects are outlined.

Jan 1, 1972

By George H. Holmes

This paper , which describes mining methods and milling and manufacturing operations at the gypsum property of the Blue Diamond Corp. , is one of a series on mining methods and practices being prepared by the Mining Division of the Bureau of Mines . The property comprises about 4,000 acres and is in secs . 30 , 31 , 32 , and 33 , T. 21 S. , R. 59 E. , and secs . 5 , 6, 7 , 8 , and 9 , T. 22 S. , R. 59 E. , M. D. B. and M. , Clark County , Nev . , approximately 23 miles by paved highway southwest of Las Vegas , Nev . ( fig . 1 ) . This circular summarizes the history of company operations , describes physical features , labor and living conditions , and the geology . The method of exploration is outlined , and the section on mining methods contains descriptions of open - pit and underground systems , including loading and transportation methods . The crushing plant and tramway are described , as well as plaster-mill and board -plant practices . The boiler plant and organization are described , and wage scales are contained in the concluding section of the circular .

Mar 1, 1950

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By John Paul Gries

During World. War II, when the curtailment of imports led to an unprecedented demand for domestic mica, beryl, spodumene, and other pegmatite minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite mining of these minerals from the Black Hills area of South Dakota. The program involved napping, sampling, and drilling of many pegmatite dikes in the southern portion of the Black Hills and beneficiation conducted in the field and in the Bureau of Mines laboratories at Rapid City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This report describes the occurrence and sampling of the Beecher No. 2 pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Beecher No. 2 pegmatite was started on November 20, 1943, and terminated in the spring of 1944. During this period, the Bureau of Mines took a series of trench samples across the pegmatite at the surface for grain-count studies and chemical analyses. The Geological Survey mapped the geology of the deposit after it was exposed by trenching and stripping.

Jan 1, 1950

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By Lester J. Crow

A preliminary survey was performed to investigate the impregnation of relatively weak, porous volcanic tuff and a relatively strong, dense sandstone with five different monomers. Increases in compressive strengths by factors of 2 to 5, and elastic moduli by factors of 2 to 3.5, are reported for natural rocks (tuff., sandstone, dacite), which were impregnated with five monomers (methyl methacrylate; chlorostyrene; 40 percent TMPTMA-60 percent styrene; 40 percent TMPTMA-60 percent chlorostyrene; 60 percent polyester-40 percent styrene); polymerization took place after monomers were forced into the rock. Impregnation was performed (1) by pressurizing rock specimens from one end, or (2) by a vacuum-soak operation. Polymerization was accomplished by either radiation or chemical initiation techniques. Strength improvement is dependent on (1) the type of monomer used, (2) the amount of polymer incorporated into the rock, and (3) the degree of water saturation of the rock. Water saturation strongly reduced the effectiveness of the method for the polymer systems tested. The more viscous monomers (for example, 60 percent polyester-40 percent styrene) were more effective in displacing the water from the rock, and compressive strengths of wet rock were doubled with these systems. Water saturations ranging from 25 to 100 percent of maximum saturation gave essentially identical results. Further tests on other types of mine rock; including shale and coal, are planned. Water-compatible polymer systems should be developed, or present systems should be suitably modified. For application to tunnel stabilization, design studies evaluating the improvement in rock strength and its influence on the support system are also recommended.

Jan 1, 1971