Search Documents

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

By Leslie Taylor, Kevin Genson

This paper reports on an experimental study of the effect that bottom shaping might have on the impulse delivered to a light armored vehicle due to a buried mine detonating beneath the center of it. The study was restricted to explosives buried in saturated sand and three parameters were varied within the study: bottom angle (0 degrees to 21 degrees), depth of burial of the explosive (1.02 mm to 12.7 mm), and stand off distance (0 mm to 38.1 mm). Six hundred and thirty six milligrams of explosive was used as the explosive load. It has been shown in previously published work [1,2] that Hopkinson scaling works well for the determination of impulse loading on a semi-rigid target plates. Therefore in terms of a full scale test using 4.54 Kilograms of explosive the parameters investigated would cover a DOB of from 19.56 mm to 243.84 mm and a Stand off distance from 0 to 734.06 millimeters. These values nicely cover those of interest to the Marines with regard to the AAV (amphibious assault vehicle). Four angles were investigated at all DOB’s and Stand off distances – 0 degrees, 7 degrees, 13 degrees, and 20 degrees. The results show that reduction in impulse delivered to the target is achieved with an angled bottom on the target plate with a major reduction occurring before the 13 degree angle is reached. Hence vehicles with quite modest bottom angles could help greatly in load reduction with very little loss in utility.

Jan 1, 2008

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"An Event Tree Analysis (ETA) is an established approach for logically deconstructing and assessing scenarios for probabilistic risk assessment. This deconstruction into a series of understandable eventsfacilitates probability estimation for explicitly defined explosive terrorism scenarios with consideration of modes of possible failure during execution (a scenario is defined through selection of a target, selection of an explosive material, and interdiction prior to arriving at general target location, etc.). Further, each event is decomposed into a range of possible outcomes. The physical action or reality ofthe outcome is statistically represented by “branches” of the event tree (e.g., the terrorist may choose totarget a stadium, hotel, or subway; terrorists may be successful or unsuccessful in acquiring the material)."

Jan 1, 2017

By Andrew Drake, Mark Burchard, Peter Bellairs

The Astec Bluerock Quarry is excavating an extremely difficult to blast rock type due to its highly variable jointing density that leads to excessive oversize. A drill and blast benchmarking exercise led to eight recommendations to minimise this problem. Quarry personnel instigated a continuous improvement blasting program, that has implemented six out of eight recommendations, resulting in a large reduction in the oversize and increased crusher throughputs for a marginal 7% increase in drill and blast costs. Unit costs have reduced by an estimated 10%.

Jan 1, 1998

By Emmett J. Ientilucci, Martin Held, Xuesong Liu

Mining is crucial for advancing technology and science by providing essential resources and materials. Quarry blasting, a necessary process in mining, releases these resources and chemicals, driving research and engineering improvements. However, NOx (nitrogen oxides) is an undesired contaminant produced during quarry blasts, posing a significant negative impact on mining activities. Therefore, detecting and quantifying NOx emissions is essential for designing effective blasts, analyzing their dynamics, and reducing contaminant production. Image processing and machine learning, including deep learning methods, have been applied to solve smoke plume detection and segmentation tasks. Most research has focused on smoke from campfires or forest fires, which are important for early fire and smoke detection. However, there is limited research on quarry blast smoke using machine learning methods, which presents challenges for recognizing the smoke plume from complex background scenarios and objects, including collapsed rocks, scattered soil dust and dirt, and the dynamic movement of the scene due to blast vibrations. Detecting NOx within the smoke plumes is further challenging because NOx must be distinguished from the overall smoke plume, as they share many common spatial features. To resolve this issue, we propose an ensemble method for NOx detection that combines smoke plume segmentation with NOx fume detection. First, we apply a smoke plume segmentation model to identify the smoke plume regions. Then, we use these masked-out smoke plume regions to detect NOx based on its unique color features. The first stage of the ensemble method helps block out complicated confusers in the background, such as reddish and brownish dirt. Next, we specifically design a color classifier for NOx to further improve its sensitivity. We evaluate the overall video-wise performance using accuracy, false alarm, and miss rates based on sampled image frames from videos. Additionally, we assess the mean Intersection over Union (mIoU) for smoke plume segmentation and the mean Average Precision (mAP) for image-wise performance from an algorithmic perspective. In summary, this paper represents the first attempt to apply machine learning approaches to NOx detection in a memory-efficient and time-efficient manner.

Jan 21, 2025

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By Ambrose Buchanan, Rob Farnfield, Charles Adcock

Beginning on 7th September 1940 the City of London was subjected to 57 consecutive days of bombing in what became known as the ‘London Blitz’. To commemorate the 70th anniversary of this event a television series was commissioned that required the open detonation of World War 2 equivalent bombs close to purpose built structures constructed using period design and materials. The structures were built on a remote test facility in the North of England that is able to fire large quantities of explosive in the air.

Jan 1, 2011

By David Leidel, Beth Shimer, James Stuart

Periodically, the Institute of Makers of Explosives Safety Library Publications are reviewed, edited and updated to reflect recent technical developments, new commercial explosive products and new regulatory requirements. The rapid proliferation of electronic devices, particularly portable communication systems, inventory management devices, navigational aids, etc., required the revision of the IME Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators”. The new edition of SLP-20 has been updated to correct alterations to U.S. frequency allocations and maximum transmitted power permitted and a discussion of communications and tracking systems required in underground mining by the Miner Act. Also, an entire section was added dedicated to safe distances from RF sources to the special type of resistorized electric detonators used in the upstream oil and gas industry on wellsites and an enlarged section describing the particular types of RF sources that the blaster may encounter, perhaps in construction blasting operations.

Jan 1, 2012

By P. E. Hoffman, Joshua Ph. D.

The Institute of Makers of Explosives (IME) led a post-detonation debris collection project in conjunction with a large AN railcar detonation conducted by the Department of Homeland SecurityTransportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in the IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk) Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about AN detonation characteristics when it is driven to detonation. The test took place at the Utah Dugway Proving Grounds (DPG) on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. This paper details the collection efforts, challenges, and lessons learned. It also presents some of the initial findings relating to the debris distribution.

Jan 1, 2019

By Derek Morris, Vito Saccheri

In the monitoring of seismic exploration (whether by explosive or vibratory energy sources), the intensity of shaking at neighboring structures can now be measured quite accurately and comprehensively with portable equipment. However, the interpretation of the results is open to considerable debate and mis-interpretation. One conventional approach is simply to compare the maximum measured peak particle velocity (PPV) with a permissible standard – usually 0.5 inches/sec (1.3 cm/sec) because this is the value generally referred to in the U.S. Bureau of Mines standard. This can be very conservative, both for surface structures, and especially for buried structures like pipes, for which absolute reliance on PPV obscures the true complexity of field problems. Quite apart from the fact that the full Bureau of Mines standard is actually a reasonably complex function of frequency (for the simple reason that in differing parts of the frequency spectrum, damage may be displacement or acceleration controlled), the effects of spatial direction and orientation are often ignored.

Jan 1, 2009

By Jack Eloranta

Transmission of sound through the atmosphere is affected by local conditions. Anecdotal accounts of the sound of cannon fire traveling great distances go back to the Civil War. The Royal Society published a paper near the turn of the century concerning the reports from the cannons fired in London at the funeral of Queen Victoria. Early computers were used by the U.S. Army at Aberdeen in Maryland in the 1950’s to model airblast problems during munitions demolition. Today’s blaster has to have access to weather information beyond a simple local forecast. Surface winds, winds aloft and temperature profiles have a dominant role in neighbors reaction to blasting. Many ground vibration complaints are really airblast complaints. Blasters who maintain ground velocities under . 1 inches/ second are often perplexed by complaints from distant neighbors, even when local monitoring shows airblast to be under 110 dB. This paper will help the blaster identify warning signs of high airblast conditions.

Jan 1, 2000

By Guo Ziqing, Tang Qiuming, Liu Yuanyuan

The channel-type non-mechanical stirring production process is a new developed technology for emulsion explosives in recent years. It removes traditional equipment such as mechanical-mixing emulsification, mechanical-mixing sensitization, matrix pumping, and explosive pumping, and has been applied in China. This technique achieves a fusion of higher intrinsic safety and lower cost, as well as the excellent quality of products and high efficiency of production. The emulsion particle diameter is about 0.5μm. The storage period of emulsion explosive produced with span-80 emulsifier is more than 7 months.

Jan 21, 2025

By D Linn Coursen

Detonation propagates in the subject blasting agent at about 2.7 km/sec when it is heavily primed but explosion propagates in it at only about 0.43 km/sec when it is lightly primed. When propagating at 0.43 km/sec, it produces a borehole pressure that is slightly less than 1 kb, but no yellow fumes or other sign of incomplete reaction. It is a pumped AN/emulsion blend to which additional water is added by circumferential injection at the inlet of the hose through which it is pumped.

Jan 1, 1994

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

By Emily Johnson, Catherine Johnson, Ben Sonpon, Kelly Williams

The effect of length to diameter of the detonator is compared using Ansys/Autodyn 2-D simulations, the results of which are validated experimentally. It was found that higher pressure comes with a larger diameter, because it will result in more explosive energy being allocated out the end of the detonator.

Feb 1, 2020

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By Deane Tunaley, Paul Tidman, Qian Liu, John Mullay

Laboratory studies have indicated that the crystallization and desensitization of microballoon sensitized emulsion explosives start immediately after shocking or pre-compression. However, the question of whether or not the shocked emulsion could be worsened by the growth of crystallization or recovered by rebounding back to lower densities has been rarely examined under actual rock blasting conditions. This study was primarily intended to investigate the desensitization characteristics of two commonly used emulsion products in terms of blasthole spacing and delay duration. In the experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1995