Search Documents

By R. Winand, P. Harlet

he cathodes produced are of electrorefined grade; metallographic structure and surface roughness are controlled to a depth of 1.3 cm (single-side deposits); silver levels in the cathode are regulated by the presence in solution of Cl- and Br- ions; organics must be used at very low concentrations (around 0.1 mg/l with a consumption of about 0.01 mg/l/hr). The required concentrations of additives were established according to a well-defined strategy based on the consumption of organics at the cathode by a mass transfer limited-process.

Jan 4, 1992

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

By J. H. E. Jeffes, K. T. Jacob

Solid oxide galvanic cells, of the type: Pt,Ni-NiO | Solid electrolyte | O(metal),Cermet,Pt, were used to measure the activity coefficient of oxygen in liquid Cu at 1 100 and 1 300°C and in Pb at 1 100°C. Similar cells were used to study the activity coefficient of oxygen in the whole range of Cu + Pb alloys at 1 100°C and in Pb-rich alloys at 900 and 750°C. The results obtained are discussed in terms of proposed solution models. An equation based on the formation of 'species' of the form M(2)O in solutions of oxygen in binary alloys is shown to fit the experimental data

Dec 1, 1971

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993

By L. R. Chimimba

"The Trojan nickel deposit occurs within a pile of ultramafic lavas subjected to a lower amphibolite grade of metamorphism. The lavas form part of the Upper Greenstones (Bulawayan Group) of the Mazoe greenstone belt. The nickel mineralization occurs as disseminated, massive and near-massive sulphides. The massive and near-massive ore occurs along the basal contact of the serpentinite units and is overlain by the more abundant disseminated ore, which occurs within the serpentinite. The main sulphide minerals are pyrrhotite. pentlandite and chalcopvrite. Minor amounts of millerite and pvrite are present. The Ni : Cu ratio in all three types of ore averages 15:1.The intercumulus nature of sulphides in the near-massive ore and similar textures occasionally seen in the disseminated ore indicates a magmatic origin of the mineralization. The basal position of the near-massive and massive ore suggests that the sul­ phides settled out under gravity during the emplacement and crystallization of a peridotitic magma. The deposit has been deformed and some of the primary massive ore has been remobilized into veins and breccias. The disseminated mineralization now occurs mainly as blebs of sulphides intergrown with silicate minerals or as stringers of sulphides between foliation planes in the serpentinite."

Jan 1, 1984

By D. V. Venugopal, W. W. Gardiner

Spessartine-quartz rocks are manganiferous sedimentary rocks rich in spessartine and quartz which occur in north-central New Brunswick. They represent a recrystallised manganiferous siltstone/chert that is contained in or associated with red manganiferous siltstone (RMS) units. The spessartine-quartz rocks and RMS form part of an Ordovician volcanic and sedimentary succession within the Appalachian-Caledonian orogen which hosts numerous massive sulphides and polymetallic vein deposits. The New Brunswick spessartine-quartz rocks are spatially and temporally associated with stratiform base-metal, precious metal and hydrothermal tin-tungsten deposits. This suggests that spessartine-bearing lithologies and zones can be useful in predictive metallogeny and for the understanding of the stratigraphy and palaeographic setting of the early Palaeozoic rocks of the Appalachian-Caledonian orogen.

Jan 12, 1992

By Li Shibo, C. Halls

The compositions of olivine, pyroxene and chromite from the Proterozoic ultramafic complex are analagous to those of cumulate ultramafic rocks of tholeiitic origin, suggesting that the parent magma may have been tholeiitic rather than komatiitic. The complex contains economically significant Ni-Cu sulphide mineralisation. The high sulphide/silicate ratio is best explained in terms of the segregation of sulphides from a large volume of magma, of which all but the ultramafic cumulate fraction has since been eroded. Platinum-group minerals that have been identified include sperrylite, moncheite, native platinum, froodite, merenskyite, michenerite and Pd-rich pentlandite lamellae exsolved from pyrrhotite. They are characteristically found in close association with chalcopyrite, either along the contacts between hydrosilicate and sulphide grains or in cracks within pentlandite and chalcopyrite, which may also be intergrown with galena. Crystallisation from a Cu-rich residual magmatic liquid also enriched in Pt, Pd, As, Sb, Bi, Te, Zn and Pb is postulated.

Jan 12, 1993

By M. Rahman, P. C. Kapur

The fixed-time locked-cycle grinding test is employed to simulate the industrial closed grinding circuit on the laboratory scale. A mathematical algorithm for 'cyclewise' computer simulation of the locked-cycle test has been derived and used to study an idealised laboratory-scale model of a closed ball-mill circuit. The agreement between simulated and experimental results is reasonably good, except when the grinding times are relatively long

Dec 1, 1971

By J R. Leeming

The paper describes a technique that has been developed by the Health and Safety Executive (USE) to make an assessment of the effectiveness of Health and Safety (H and S) management at complex sites. The paper then describes how the technique was adapted and used for the first time at a large coal mine. The results highlighted certain deficiencies in the safety management system, allowing directed advice to he given to management.

Jan 4, 1997

By T. Guyaguler

An analytical technique using computer-based multiple-regression methods was employed to determine the relation between the dust-producing index and inherent rock properties of typical samples from a coal-producing area, one of the aims being to provide a preliminary predictive tool for practical use. The investigation demonstrated that factors varied in their influence under different conditions, the brittleness:toughness ratio and the hardness being the most significant inherent properties with hardness showing the highest positive correlation coefficient

Jun 13, 1905

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Barclay, E. Rothery, S. H. White

Discussion by B.P.J. Stevens of the paper, published in Trans. IMMA, vol.104, 1995, p.B1-B17, is presented together with the authors' response. Stevens questions the authors' radically different interpretation of the structural geology of the Broken Hill Block, considering that the descriptive part of the paper is a useful addition but that the conclusions are unwarranted on the basis of the data presented. A number of major points of disagreement are outlined and half a dozen additional minor points listed. In response, the authors admire Stevens's contribution to unravelling the geology of the area but defend their attempts to take the regional studies a step further, pointing out that he has misquoted what they wrote and arguing that because of the assumptions underpinning the derivation of the present stratigraphy it cannot be used to constrain structural models. With regard to shear zones, they cite the extensive earlier literature and refer to horizontal displacements shown on maps produced by Stevens et al. Detailed discussion follows of the stratigraphy and of the stratigraphic correlation problems resulting from failure to recognise the presence and significance of shears, particularly those parallel to stratigraphy. The remobilised position of the Pb mineralisation in the North Mine open cut is reiterated. It is concluded that there is an urgent need for systematic isotopic dating in the area to constrain the stratigraphy

Apr 1, 1996

By S. Vardy

The paper notes that the extraction of 22% of the remaining workable reserves in the north western area involves a risk of spontaneous combustion higher than is normal in Britain. Mining systems have been tailor made in order to minimize the risk of spontaneous heatings, and these systems are described. Well-proved methods of combating spontaneous combustion are referred to, as well as the limitations which now apply to them as the result of the introduction of modern mining techniques. A substantial part of the paper is devoted to the circumstances in which spontaneous combustion occurs underground in the north western area. Several actual incidents which have occurred in the last few years, along with the practical application of the lessons learned, are described. Of particular note are: a) the procedure adopted in the north western area to equalize pressure differences across stoppings using pressure chambers, and b) a retreat mining system, primarily designed to deal with high methane emission and steep gradients, which also affords some protection against spontaneous combustion.

May 23, 1905

By Z. Sawlowicz

Finely dispersed, primary sulphide mineralisation in the Cu-Fe sulphide zones of copper-bearing shale of the Polish part of the Permian Kupferschiefer is mainly present in the form of framboids and spherules. This type of mineralisation is especially well preserved in organic-rich shale, where it often dominates over a later diagenetic mineralisation that consists of large grains and veins. In microscopic observations special attention was paid to composite grains of copper and iron sulphides. The results suggest that the Cu-Fe and Cu sulphides precipitated in the Kupferschiefer sediment before pyritisation of the framboids had ceased and that they replaced metastable precursors of pyrite. The precipitation of copper sulphides could have been delayed owing to the formation of Cu-organic complexes.

Jan 4, 1992

The report of the Annual General Meeting of the Institution of Mining and Metallurgy held on Thursday, 20 May, 1971, in the rooms of the Geological Society of London, Burlington House, Piccadilly, London, W.1, at 4 p.m. (Chairman : M. J. Cahalan, President) includes details of awards and prizes presented to William Justin Kroll, Sir Gordon Colvin Lindesay Clark, John Convey, Evert Hoek, Peter Reginald Dawson and Christopher Michael St. John

Dec 1, 1971

By John Craw

This paper has formulated the methods, both medical and engineering, for the control of pneumokoniosis in the haematite-mining industry in West Cumberland, but this is only part of a general service to improve the lot of the worker in these mines, to make him a better and happier workman, and to permit him to enjoy his work and leisure in comfort and good health. This organization has now been functioning for more than ten years and the results are indeed heartening, but it is only as a result of constant vigilance from the mining and medical point of view that such a plan can operate efficiently. The human element and its full understanding is by no means the least of the problems.

Jan 1, 1947

By L. T. Matthews, C. E. Loo

During sintering, porous ore particles are easily assimilated by liquid melt. Two simple models of the process are considered: the dissolution of a solid by a liquid and the penetration of a liquid into a porous solid. Laboratory sintering studies covering a range of experimental conditions were undertaken to characterise the assimilation of large particles of ore and flux by melts formed from different mixes of fines. For ores, the process appeared to be complicated by the detachment of fines from the ore surface prior to melt formation, according to the mass of adhering fines and surface roughness of the particle. This delayed the onset of assimilation and sometimes reduced it, although melt penetration was fast and effective. Studies using different temperature profiles suggested that the assimilation of haematite was controlled by the transport of Fe2O3 away from the surface of ore particles. The assimilation of limestone depended more on thermal conditions than on the three magnesia-bearing minerals considered. Changing the composition of the initial melt significantly altered the extent of assimilation of ores and limestone, but again had a less marked effect on the magnesia-bearing fluxes.

Jan 8, 1992

By R. W. Ruddle

The advent of new methods of roasting, “flash roasting and fluidisation”, which are now under development, combined with the use of oxygen-enriched air, may markedly increase the SO2 content of roaster smokes. Skogmo suggests that the production of smokes containing as much as 50 per cent SO2 should be feasible. The use of flash smelting processes may well enable a similar increase in the SO2 content of smelter smokes to be made. In this event the recovery of sulphur would be greatly cheapened and the process might well be much more economic, even if allowance is made for the cost of generating the oxygen

Jan 1, 1953

By A. G. Waters, N. J. Bristow

A comparative study was made of an untreated and a heated haematite ore and a sinter produced from a feed consisting of 100% ore, to study the influence on reduction behaviour of sinter bonding phases such as SFCA (silico-ferrite of calcium and alumina). Under low-temperature reduction conditions the order of increasing reducibility followed that of increasing porosity and surface area but under similar conditions at 900 degrees C the sinter exhibited higher reducibility than the ores even though the total porosity and chemical reducibility of the individual phases were lower. This behaviour can be explained in terms of the higher total porosity of the natural ore at low temperatures and the higher level of fine pores in the sinter at high temperatures due to the presence of SFCA, which acts to support the fine (c.0.1 micrometre) pores created by the reduction process. This leads to the conclusion that the main role of SFCA in sinter during high-temperature reduction is to maintain a high level of fine porosity. Some implications of this work for granule design and sintering practice are discussed

Apr 1, 1991

By J. H. E. Jeffes, C. Diaz

The heat balance and chemical equilibria involved in the production of blister copper from a chalcopyrite concentrate in a single operation are examined. It appears that two stages—one oxidising and one reducing—will be required. The analysis indicates that on thermal grounds the process is possible with a dry, high-grade chalcopyrite concentrate, if oxygen enrichment to about 30 per cent is used, but that copper losses in the slag will be serious and will require a secondary recovery operation. More extensive data on the activities of copper oxide in slags are required to elucidate this point more effectively

Dec 1, 1971