Search Documents

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By L Zhang

The Chinese coal industry is the largest coal producer in the world. The total production in I995 was 1.28 bnt. On the way towards introducing a market economic system, this mature industry is facing major challenges. The main problems are a large surplus of manpower, shortage of current assets and capital, low productivity, high casualties and a huge deficit. This paper discusses the present situation and the future developments in the Chinese coal industry. The current policy can be stated as ‘rapidly developing the state collieries and improving the village and private mines; integrated development to achieve an economic operating scale and encouraging a diversified economy; rapidly exploiting and developing in the North west and South west; promoting productivity and efficiency; welcoming multi-sources and types of investment; setting up coal exchange markets; and the careful control of resources and the environment'.

Jan 11, 1996

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

Jan 1, 1947

By T. Piirainen, T. Alapieti

"The Koillismaa layered igneous complex is the result of igneous activity that occurred 2436±5 m.y. ago. Its crystallization took place in three separate but connected magma chambers, the total volume of which is estimated at more than 2000 km'. These chambers were located partly in a feeder system within Archaean granitoids and partly in an unconformity between these grani­ toids and Early Proterozoic supracrustal rocks. The composition of the parental magma that initially filled the chambers is thought to have been that of a relatively MgO-rich tholeiite. Sulphides and platinum-group minerals are mainly concentrated in the marginal series of the western part, where they are encountered over a distance of 25 km. This marginal series is an originally nearly horizontal series of rock types that displays a reversed differentiation trend, grading inwards from gabbroic to ultramafic rocks, followed bv rocks of the layered series. The chilled margin is not encountered anywhere in its original position at the contact, probably as a consequence of magmatic erosion, but remnants are to be found in the form of elongated xenoliths. Partly melted siliceous fragments from gneissic country rock typical of the lower part of the marginal series indicate pronounced contamination.Chalcopyrite, pentlandite and pyrrhotite±pyrite are the predominant sulphides. The accessory sulphide minerals include covellite, violarite, marcasite, mackinawite, sphalerite and argentian pentlandite. Platinum-group minerals are represented by froodite, michenerite, merenskyite and sperrylite. Other accessories that have been identified are electrum and native copper and gold. The mean of the Cu/(Cu+Ni) ratio in the mineralizations is 0.67 and Pt/(Pt+Pd) 0.31.It is suggested that the sulphide phase was formed in the marginal series as the solubility of sulphur in the basic magma was lowered by contamination, possibly assisted by some other factors. The sulphur isotope data support the juvenile origin of the sulphur."

Jan 1, 1984

The Council of the Institution of Mining and Metallurgy submitted the report of the affairs of the Institution for the session 1970-71, and the Statement of Accounts for the year ended 31 December, 1970. The statistics given in the report refer to the calendar year 1970. Details are included of membership, officers, representation on other bodies, honours and distinctions, awards, meetings, publications, library, overseas activities, fellowships and grants, the revenue and expenditure account, the balance sheet, trust fund balances, contributing companies, and schedule of investments

Dec 1, 1971

By Winmill T. F.

The previous papers have been concerned only with the atmospheric oxidation of coals from the Barnsley Seam, for which it has been shown that an adequate explanation of the origin and nature of gob-fires can be based on the reaction between the coal itself and the oxygen of the air without the intervention of any other substance. It becomes of importance, therefore, to ascertain how far a similar explanation will hold good for spontaneous heating in other seams, and with this object in view samples including anthracite and lignite have been taken from a considerable number of pits in different parts of the UK (south Wales, Northumberland and Durham, north Staffordshire, Portrush and Ayrshire), some liable to fire, others not. There is abundant evidence to support the commonly-accepted view that spontaneous heating is due to the heat evolved during the absorption of oxygen from the air by coal or pyrites. The quantity of heat produced by the reaction has been measured and it has been shown that the observed rate of heating of a sample of coal agrees with the rate calculated from the heat of reaction and the rate of absorption of oxygen

Dec 1, 1916

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Bareley, E. Rothery, S. H. White

B.P.J. Stevens contributes a further response to the authors' earlier lengthy reply regarding their paper published in Trans.IMM B, vol.104, 1995, p.B1-B17, contending that despite the positive contribution clarifying their interpretations they perpetrate some misquotations, attempt to rewrite history and fail to understand the New South Wales Geological Survey's stratigraphic interpretation of the Broken Hill area. The paper's authors, in their further response, robustly defend their views, insisting that Stevens tends to misquote or take out of context what they have written and reiterating their findings that Zn is tectonically stacked above Pb at the north end of the orebody, that the written development of the stratigraphic interpretation is as they have stated, that shearing has attenuated or removed fold limbs in the Broken Hill block and that the 1:100 000 stratigraphic map reveals that magnetic anomalies are oblique to and truncated by the Geological Survey's interpreted stratigraphic boundaries

Jun 19, 1905

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By C. C. Harris

The two best known graphical methods for presenting and comparing comminution data are obtained by linearising the Gates-Gaudin-Schuhmann and the Rosin-Rammler size distribution equations. It is shown that the Gates-Gaudin-Schuhmann equation can cause excessive congestion in the 50 per cent oversize range and that, overall, the Rosin-Rammler is a better procedure. Examples are given

Dec 1, 1971

By R. J. Pine

Procedures are described for the application of risk analysis or probabilistic methods to mining geomechanics. The methods are widely applicable to existing mine design models. Detailed examples are given of plane slope failure and of pillar design based on displacement-discontinuity stress modelling and empirical strength assessment. The modelling techniques assessed are the Latin hypercube sampling method, incorporated in a spreadsheet environment, and the general point estimate method (GPEM), programmed in TurboBasic. An example GPEM program listing is included. Both methods are very convenient to use. Probabilistic acceptance criteria for slope stability after Priest and Brown are examined and alternatives are proposed where output distributions of factor of safety are approximately normal or lognormal and output distributions of safety margin are normal. The reliability index is included as a useful measure of variability with proposed acceptance criteria.

Jan 12, 1992

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By A. F. Neil, A. S. Bahaj, P. Watkins, P. M. Hyslop, C. E. Kirby, P. A. B. James

The results of initial work indicate that for 3 of the 5 quarry sands bioleaching reduces the iron oxide content to a commercially acceptable 0.035 wt% Fe20 3, although the time taken to achieve this is 14-22 days against a target leach time of 7 day. Subsequent work has identified strains of Aspergillus niger that are more efficient at producing the array of complexing agents for iron and is yielding excellent and rapid reductions in Fe levels. Potentially, bioleaching offers a more environmentally friendly and energy-efficient process for the removal of Fe from glass-making sands than conventional routes but the production of organic acids by fermentation must be achievable with low-cost substrates such as sugar-beet molasses and lactose permeates for bioleaching to offer a commercially viable alternative to treatment with hot mineral acids. Silica sands usually contain three groups of Fe minerals: iron oxyhydroxides, which comprise crystalline types such as goethite and limonite tending to occur as thin, discontinuous coatings and in cracks and crevices on the surface of the quartz; the assemblage of heavy trace minerals, which include ilmenite, rutile, leucoxene, chromite and haematite, commonly present at levels of 0.1 wt% or less as discrete grains or sometimes cemented to the quartz; and clay minerals cemented in pits on the surface of the quartz and in association with weathered, discrete feldspars. The response of the assemblage of iron minerals to short periods of exposure to hot inorganic acids is broadly related to which group they belong to, those that form coatings being accessible to acid and tending to react rapidly whereas the trace minerals are usually resistant and react very slowly, if at all, and the clays are probably digested. The note reports on a preliminary study of the use of microorganisms to develop an alternative clean technology that will give results comparable to those achievable with hot inorganic mineral acids but with more environmentally acceptable procedures. Various fungi and bacteria produce organic acids when grown in certain media. When these acids come into contact with Fe-stained sand grains the iron is removed as soluble complexes. Several strains of Aspergillus niger have been found to produce organic acids from sugar, predominantly citric, gluconic and oxalic acids, their relative yields depending on cultivation medium and conditions. Sand samples were prepared from five quarries in the UK: Levenseat, Lothian; Redhill, Surrey; King's Lynn, Norfolk; Chelford, Cheshire; and Oakamoor, Staffordshire; ranging in iron oxide content from 0.035 to 0.153 wt% Fe203

Jun 18, 1905

By Fergusson E.

An account is given of the history and operation of the Straits Tin market and the Penang price. The procedure by which the official ruling tin price is determined is presented and the way in which bids are treated is outlined: the price declared in Penang is the result of a joint operation by the two Malaysian smelters and is arrived at by finding the highest price at which the whole of the day's offerings for sale can be sold, thus reflecting the marriage of the offerings of the individual mine producers with the demand for Straits Tin from the consuming countries of the world. A system of accurate weighing, sampling and assaying of concentrates delivered to the smelters' premises enables the various ore-buying agencies of the two smelters to notify their central offices promptly of the estimated tin content of the concentrates their customers wish to price that day, so that by 11.00 a.m. both smelters will have exchanged with each other figures giving the total quantity of metal they have for inclusion in the day's market, at the same time exchanging particulars of the bids they have received. Miners are encouraged to sell regularly for cash and an evenness is thus achieved which avoids large daily fluctuations in overall quantity.

Dec 30, 1971

By A. D. Fowler, M. T. Anderson

A phenomenological model is presented that relates Pb-Zn mineralisation to proximal geopressure zones. Typically, geopressure zones (GPZ) consist of masses of undercompacted sediment encapsulated within impermeable shales and are characterised by high formation fluid pressures. Heat flow is perturbed in some GPZ on account of their insulating properties. Geothermal gradients as high as 150 degrees C/km have been observed over short distances in the sediments of the US coast of the Gulf of Mexico. Some modern geopressure zones are known to reach temperatures of 120-150 degrees C at depths of 2.5-3.5 km. It is demonstrated that the zones may act as proximal sources of hydrothermal fluids, thus explaining the high temperatures of mineralisation observed in the deposits, which are hosted in basins characterised by thick, rapidly deposited, shale-rich clastic sequences

Jan 1, 1991

By Simons W.

The object of the paper is to describe the standards of quality that should be specified in ordering material ordinarily required for colliery use, and also the qualities most suitable for particular purposes. Tables are presented of British Standard tests for wrought iron grades A, B and C, Admiralty tests for iron in chain, the quality of material for wheels and axles, and the composition and mechanical properties of wrought iron, Armco (ingot) iron and drawbar-gear steel. (Paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, Mr. John Gregory, President, in the chair)

Dec 1, 1916

By D. J. Reddish, B. N. Whittaker, G. X. Sun

An image analysis technique has been used in the assessment of subsurface fracture levels in the context of water inflow into longwall mine workings. The technique was used to analyse results from physical modelling which are represented by black and white photographs taken directly from the model tests. Binary images of fracture patterns are obtained by scanning the photographs with an image analyser coupled to a video camera. The images are manipulated by a C program which allows them to be processed in vertical and horizontal directions and filtered to differentiate quantitatively between vertical and horizontal fracture intensities. The fracture density distributions provide a valuable database for further numerical and statistical analysis. This allows assessment in terms of water inflow into the excavation. A comprehensive image analysis was undertaken on several extraction models. Results indicate that extraction thickness has a significant effect on the fracture pattern and the fracture density distributions. The results can be used to adapt model findings to situations with a range of extraction thicknesses. The technique has allowed improvement in image enhancement and in the interpretation of model results. In particular, a qualitative comparison between different models is possible.

Jan 12, 1992

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916