Search Documents

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By S. Gomez, P. A. Bebswa, A. N. Mwale

"The research aimed at improving the way screen performance analysis is conducted using a model that accounts for most feed and design parameters in its formulation. Thus, the aim was to validate the fine screen model that was developed at the Centre for Minerals Research (CMR) unit at the University of Cape Town. Fine wet screening is increasingly becoming an important application in fine grinding operations. Minera Saucito, a lead-zinc Mexican mine has replaced hydrocyclones with eight stacks of five decker derrick screens to close the ball mill in their concentrator plant. The five decker stacks have improved the overall plant throughput by 20% and have had the ball mill circulating load reduced considerably. As a continuous plant optimization process, a number of surveys were carried out to assess the performance of the 75 µm panel aperture installed screens. The surveys were conducted at seven different feed rates to the entire nest of screens to collect performance data. Using the fine screen model to analyze the results, it is found that as the feed rate increase, the sharpness of separation reduces. The CMR fine screen model was fitted to these results. The model fits the plant data with good accuracy. Simulated results based on this model are also presented.INTRODUCTION The potential of high frequency vibrating screens has long been identified as an alternative to hydrocyclones in grinding applications (Rogers and Brame, 1985). However, high frequency vibrating screens have had two main disadvantages, low capacity and high wear rates (Kelley and Mckeon, 2005; Teknikk, 2009). Current vibrating screen technology overcomes these challenges by multiple deck screen design and use of wear resistant urethane materials for panel construction (Kelley, 2007; Valine and Wennen, 2002). For a example, the Derrick screen’s material of construction is a tensionable urethane that provide high open area ranging between 35 to 45% with considerably reduced blinding (Valine and Wennen, 2002). Thus, there has been an increased uptake by the mining industry in the use of wet fine vibrating screens closing the ball mill as the final classification stage in the comminution circuit (Barkhuysen et al., 2010; Frausto, Ballantyne et al. 2017; Pelevin and Lazebnaya, 2009; Teknikk, 2009). Even though there is a number of models in existence, none of these models adequately predict the performance of high frequency vibrating screens (Karra, 1979; Rogers, 1982; Subasinghe et al., 1990; Trumic and Magdalinovic, 2011). Recently Mwale et al., (2016) developed a model for predicting the performance of high frequency vibrating screens using the partition curve properties. The input parameters of the model include screen open area (??) in m2, tonnage feed rate (????) (tph) and the weight fraction of solids (??) in the feed for a given panel aperture size. The model was developed based on data collected from a single deck industrial size derrick screen, in a pilot setup. The work presented in this paper is an attempt to test this model using data collected from Minera Saucito concentrator, an industrial plant whose comminution circuit is shown in Figure."

Jan 1, 2018

By Reza M. Rahman, Seher Ata, Graeme J. Jameson

"This paper presents the results of a through investigation into the froth recovery measurements in a controlled plant environment using a device that allows direct collection of dropback particles from the froth phase. Test work was performed at the Northparkes concentrator (NSW, Australia), using a feed taken from the head of the cleaner scavenger bank. The feed slurry had a relatively higher copper grade varying from 5.2% to 6.8%. Experiments were performed to investigate the effect of important flotation parameters such as air flowrate on the froth recovery. The size of the particles in the relevant streams was also analysed to acquire in-depth knowledge about the froth dropback mechanism. The results suggested that the froth recovery could be as low as 70%, although it was relatively easy to achieve the values in the range 75% to 85% by the correct choice of operating variables. It was found that the air flowrate has a positive impact on both collection (pulp) and froth zone recoveries. However, the effect was more prominent in the froth zone. It appeared that the froth recovery is a strong function of particle size."

Jan 1, 2014

By D. B. Mazzinghy, L. C. de R. Machado, H. Delboni, M. G. Bergerman

"The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades, as a result of growing requirement for finer ore grinding. This equipment delivers higher energy efficiency in fine grinding operations when compared to conventional tubular mills. Methods for designing vertical stirred mills involve operational experience, pilot plants and bench tests. An important issue is that these tests require, at a laboratory scale, at least 10–20 kg of material, depending on its density, which is not available in many cases, particularly in the early stages of greenfield projects. For the regrind of flotation concentrates, several bench scale flotation cycles are required to generate such a sample. This paper describes the development of a laboratory jar mill test using a 6”x8” jar – smaller than that commonly used – based on the overall specific energy method, which requires significantly less mass compared with existing tests. The proposed test has proven to be more practical than tests normally used, requiring about a quarter of the mass, and also shows good adherence to industrial results for the studied iron ore processing plant. INTRODUCTION A significant demand for finer grinding has been noticed over the past few decades in several mining projects to achieve the mineral liberation required for the concentration of valuable minerals. However, the finer the product size, the greater the grinding energy consumption, resulting in an overall increase in operating costs, which may reach or even exceed 50% of the mineral processing cost (VIEIRA, PERES, 2013; DANIEL, LEWIS-GREY, 2011). Comminution technology can have a major impact on subsequent ore concentration stages (DANIEL, LEWIS-GREY, 2011; MARSDEN, 2009; NAPIER-MUNN, 2012; PEASE et al., 2010), which further strengthens the importance of proper technology and equipment selection. Adequate grinding circuit selection and design is thus a key aspect associated with mining projects."

Jan 1, 2018

By Vladimir G. Kochnev

An innovative AG and SAG technology aimed to be applied in grinding of ores and in the production of construction materials is described. A novel design of a cantilever-type mill capable to operate in autogenous, semi-autogenous and ball grinding mode ensures easy delivery and installation even in remote areas, and low capital and operating costs. Results of the tests of the new heel-shaped liners performed by TTD jointly with ALROSA, MINTEK and Anglo-American Corporation are reported. The approach includes also a novel discharge grid design and a technique of treating the material of critical size. These innovations make grinding in AG and SAG mills dramatically more effective, with an increase in the throughput rate and a reduction in power consumption ranging from 1.5 to 2 times.

Jan 1, 2003

Pure camsellite samples were prepared through crushing, sorting and grinding the high-grade iron-containing camsellite ores from Fengcheng, Liaoning, China. The flotation behaviour of camsellite was studied via a systematic investigation of camsellite flotation re-covery changes as a function of choices and dosages of collectors and depressants at different slurry pH. The results showed that at pH 8.5 to 9.5, the recovery of camsellite reached the maximum at 90%~93.5% using dodecylamine as the collector, while under the same condition a recovery of 84%~86% could be achieved with sodium oleate. The adsorption of dodecylamine was not affected by the addition of sodium hexametaphosphate, but the adsorption of sodium oleate could be significantly depressed. This implied that sodium metahexaphosphate could be used as an effective depressant for the other associated minerals during the dodecylamine flotation of camsellite. When starch was used as the depressant, the flotation of camsellite by sodium oleate was almost completely depressed in the alkaline conditions. Significant depressions were also observed when calcium chloride was added in the camsellite-sodium oleate system. The higher the slurry pH is, the stronger the depression. Zeta potential measurements indicated that the flotation was mainly initiated by the electrostatic adsorption of the collector on camsellite. X-ray photoelectron spectrometer (XPS) analysis showed that the adsorption was originated from the electrostatic attraction between the N atom in dode-cylamine and B atom in camsellite. Dodecylamine had a higher coverage on the camsellite surface than sodium oleate.

Jan 1, 2014

By Brian Hart, Stamen Dimov

"In refractory ores, a substantial part of the gold content may be present as a sub-microscopic component within the mineral matrix of the various carriers. This type of gold may be present as finely disseminated colloidal size gold particles (<0.5µm) or as a solid solution within the sulphide mineral matrix. Such ores are not amenable to gold recovery by direct cyanidation. In order to liberate the sub-microscopic gold, the ore has to be oxidized before being subjected to gold cyanidation and extraction. Autoclave pressure oxidation (AC POX) of the sulphide ore and subsequent cyanidation is a common technology used to liberate the gold in such refractory ores. The additional presence of active carbonaceous matter in such ores (double refractory ores) represents another major obstacle for efficient gold recovery during the process of pressure oxidation and cyanidation. This carbonaceous matter (c-matter) can adversely affect the gold recovery due to its ability to adsorb, or pre-grob gold from the cyanide solution. Advanced micro-beam analytical techniques such as Dynamic Secondary Ion Mass Spectrometry (D-SIMS) and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) have become powerful tools for characterization of different forms and carriers of gold for the needs of the mineral processing industry. Major advantages of these techniques are related to their ability to analyze individual mineral particles and provide quantitative analysis with detection limits in the low ppm/ppb concentration range. This paper describes various micro-beam techniques and procedures implemented at Surface Science Western (SSW) for quantification and characterization of the sub-microscopic gold and the preg-robbed surface gold as part of full gold deportment studies in feeds and process stream products."

Jan 1, 2014

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.One of the simplest separators is the sluice, in which separation takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in so-called hindered settling mode.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates.The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ‘law of the wall’ model.Particle concentration distributions were described using Hunt’s sediment transport model, assuming the particle eddy diffusion coefficient to be the same as that for the water. Settling velocities were calculated using either the Richardson and Zaki or Brauer and Thiele models. The latter takes into account particle size and density distributions and solids volumetric concentration.The resulting predictions of particle separation are remarkably good, even though the model does not model the local settling velocity in the slurry."

Jan 1, 2003

By P. S. Mukherjee

Mineral ilmenite is a major resource for titanium, whose major application is for production of Titanium dioxide (TiO2) for pigment application. The production of pigment grade TiO2 from ilmenite was earlier carried out by acid leaching, which has now been banned due to environmental regulations. Further acid leaching leads to loss of iron metal values as sulphate or chloride which are also treated as effluent. In thermal plasma processing the metal values are recovered as high value pig iron and Titanium dioxide is recovered as Titania rich slag containing 80 to 85 percent TiO2. The Titania rich slag has now been considered as a better input material than synthetic rutile for production of pigment grade Titanium dioxide. On the other hand, high value pig iron goes for automobile industry for specific application. An Inflight-flight Thermal Plasma Processing plant, used for the production of Titania Rich slag and high value Pig iron from ilmenite, with 20kg capacity was designed and fabricated. The reactor has the provision to utilize the flue gas generated for preheating the input of raw materials. Various aspects of designing the furnace operation include viz. Feeding the raw material at a fixed rate, designing the crucible used for melting ilmenite, proper cooling arrangements, an innovative method for tapping the melt, recovery of heat from the gases, various safety arrangements which are some of the important milestone of the present work. The various operations have been carried out through a controller panel. Experiments were carried out to optimize various processing parameters using statistical modeling. Large scale experiments have been carried out at 10 to15 kg scale. The material balance has been calculate, and it has been observed, that about 95 percent recovery could be obtained for both Iron and Titanium oxide from ilmenite. The detailed characterization on Titania rich slag and iron has been carried out. It has also been shown that using the above slag, it is possible to prepare nanosized Titanium dioxide powder containing about 98 percent Titanium dioxide by optimizing leaching conditions. Keywords: titania rich slag, ilmenite, thermal plasma

Sep 1, 2012

In this study, the effect of different regrinding conditions on the depression of fine pyrite at the cleaner stage was investigated. The regrinding condition was manipulated by different grinding media (stainless steel and mild steel). It was found that, after regrinding with mild steel grinding media, the flotation recovery of pyrite is much lower than with stainless steel grinding media, and it is more difficult to restore by adding more collector. This means, regrinding with mild steel grinding media may depress the pyrite flotation more strongly. The copper activation of pyrite during regrinding was also studied. It was found, that the mild steel grinding media is more beneficial to copper activation than stainless steel media. Additionally, the analysis of pyrite recovery based on the particle size indicated, that the fine particles are more susceptible to different grinding environments than intermediate and coarse particles and therefore are more easily depressed with a much lower flotation recovery.

Sep 1, 2012

By Brian Hart, Liuyin Xia, Staman Dimov

The recovery of rare earth elements (REE) is fast becoming of significant interest globally. Modern research and development programs (outside China) towards the optimization of REE mineral recovery by flotation have been lacking. Due to the mineralogical nature of many hosting deposits, the separation and recovery flotation flowsheets can be very complex. As part of a research project, a selected suite of hydroxamic acid collectors (Naphthoyl, Cyclohexyl, Benzoyl, Octyl, Terta-butyl benzoyl, Salicylic) were tested in order to examine their potential for recovery and selectivity. Micro flotation tests were conducted on a feed sample, recovery and grade of the products were used to evaluate their relative flotation efficiency and selectivity and these results (flotation with the hydroxamate collectors) were compared to a phosphoric acid/sulphonate collector mix(shorten as "mixed"). In the testing, the flotation response with the hydroxamate collectors was significantly better than the "mixed" collectors on freshly ground (no slimes removed) samples. Furthermore the tests revealed that for most of the hydroxamate reagents tested, their dosage requirements to achieve recoveries at the same levels was less than that for the "mixed" reagents. Product assays show that recovery of both La and Ce is significantly better for using the salicylic hydroxamate and that Nb, Y and Zr recovery are favored by using octyl hydroxamate. These results indicate mineral flotation selectivity could be achieved by using selective hydroxamtes. Spectral fingerprinting by TOF-SIMS surface analysis has allowed for the identification of reagent species. TOF-SIMS surface analyses of grains analysis confirmed that REE bearing grains reporting to the concentrates are doing so in response to collector attachment whereas grains reporting to the tails are doing so in response to a lack of collector. The TOF-SIMS surface data bas been used to examine the factors promoting flotation stream partitioning.

Jan 1, 2014

By Gus Van Weert, Samuel A. Bolorunduro, David B. Dreisingerm

"As deposits of high-grade base metal sulphides become depleted, attention must be focused on the treatment of complex sulphides, which contain significant fractions of precious metals such as gold and silver. Acid pressure oxidation is a promising process for these materials and the recovery of silver and gold will improve the economy of the process. Gold can be recovered from the oxidised residues, however, silver is incorporated into the jarosite specie and the cyanidation of the resulting residue yields very low recovery.Pressure oxidation of various complex sulphides was carried out at 110-150°C in sulphate media with additions of potassium iodide under conditions similar to industrial autoclaving. The resulting residues were subjected to cyanidation. High recovery of silver, up to 98%, was achieved because its incorporation into lead-hydronium jarosite during the pressure oxidation was minimised, while its deportment into the cyanide-soluble silver iodide was favoured. Silver recovery decreased slightly at high temperatures (140° and 150°C) because of the enhanced stability and kinetics of lead-hydronium jarosite, but this could be overcome by increasing acidity and iodide concentration of the autoclave slurry."

Jan 1, 2003

By Anuttam Patra, Romain Bordes, Andreas Fredriksson, Tommy Karlkvist, Krister Holmberg, Kota Hanumantha Rao

Almost all of the flotation reagents used today were discovered by continued application of empirical methods and/or trial and error experimentation. Moreover, with the metal-ion specific approach used so far, it is difficult to separate the minerals containing the same constituent metal ion. A critical assessment of molecular recognition processes involved in biomineralization suggested the possibility of using reagents which are surface specific. The concept that the molecules consisting of two or more functional groups having appropriate spacing between those so as to achieve structural/stereochemical compatibility during interaction with the mineral surface exhibit structure-specificity is thought to be extended to the design of specific collectors in flotation processes. In the present study, for the first time, a rational design of surface active molecules, and thereby the recognition of crystal faces (of minerals) by these molecules through structural and stereochemical matching is being utilized successfully to selectively float various minerals. For this purpose, carboxylate-based collectors (for mineral specific flotation of calcium minerals) as well as xanthate-based collectors (for mineral specific flotation of sulphide minerals) with a fixed alkyl chain length but having two functional groups with varying geometrical distances (separated by a spacer of one, two and three carbon atoms) between them have been synthesized. In this article, we have discussed the design, synthesis, purification of these novel mineral specific collectors as well as their important solution parameters in relation to flotation processes.

Jan 1, 2014

By Seungwoo Park, Gaurav Soni, Roe-Hoan Yoon, Hyunsun Do, Kaiwu Huang

In a flotation froth (and foam), air bubbles become larger due to coalescence, causing bubble size to increase, bubble surface area to decrease, and hence casing less hydrophobic particles to drop off to the pulp phase below. Thus, bubble coarsening provides an important mechanism by which product grades are increased. On the other hand, excessive bubble coarsening results in low recoveries. In the present work, a model describing the process of bubbles becoming coarser in a foam as they rise to the top by deriving a mathematical relation between the Plateau border area, which controls film drainage rate, and the lamella film thickness, which controls bubble-coalescence rate. The model has been derived by assuming that liquid drainage rate increases due to slip at the air/water interface, and that the critical rupture thickness is determined by the capillary waves created by thermal motion. The model developed in the present work can predict the bubble size ratio between the top and bottom of a foam as functions of aeration rate, foam height, and surface tension (frother dosage). The model predictions are in good agreement with the changes in bubble sizes measured using a high-speed camera.

Jan 1, 2014

By P. Chris Pistorius, Johannes Sono, Rossouw Sono, J. J. Kobus

Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. These differences were highlighted when a plant which processes titaniferous magnetite had to change to different coal types after decades of operation. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. Direct reduction was evaluated by isothermal experiments using a packed bed of ore and coal, measuring the off-gas composition to determine reaction rates and departure from equilibrium. These indicated reduction to be under mixed control, and quite sensitive to temperature (confirming that the coal reactivity is of importance). An aspect of electrical smelting was assessed by determining dissolution rates of the coal in molten iron at 1550°C. Dissolution rates did correlate with differences in coal structure, as determined by X-ray diffraction, with the more ordered ("more crystalline") coal dissolving faster. The conclusion is that the coal which is more reactive during direct reduction is less reactive during dissolution. However, it is concluded that controlling the temperature during direct reduction offers a feasible method to reconcile the two process steps.

Jan 1, 2003

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By M. Minagawa, G. Granata, C. Tokoro, T. Kato

"In this work, we studied the mechanochemical activation of chalcopyrite by vertically stirred ball milling (VSBM) to enhance the dissolution of copper. By using x-ray diffraction (XRD) and laser diffraction particle size analysis, we investigated the effect of milling and milling conditions on particle size and phase composition of the chalcopyrite concentrate. To elucidate the efficiency of VSBM towards the mechanochemical activation of chalcopyrite, we also conducted leaching experiments in sulfuric acid-ferric sulfate media. Under all investigated milling conditions, the VSBM determined a dramatic decrease of particle size from over 100 µm of P80% up to about 13 µm. Furthermore, the XRD of the ground chalcopyrite specimens highlighted a partial oxidation of the mineral. In leaching, upon grinding by VSBM, the increase of copper extraction ranged from a minimum of +10% to a maximum of +40%, depending on the grinding conditions. In order to elucidate whether the dissolution enhancement was a consequence of the decreased particle size or of an induced mechanochemical reaction, we performed leaching experiments on activated and non-activated chalcopyrite sample having the same particle size. In addition, we determined the activation energy of leaching before and after vertically stirred ball milling. The leaching results on samples with the same particle size highlighted a greater copper extraction and higher dissolution rates upon mechanochemical activation. Whether performing grinding by VSBM or not, the leaching kinetics was found to be controlled by the chemical reaction on the surface of the chalcopyrite particle. By grinding the chalcopyrite concentrate by VSBM, the activation energy of leaching slightly decreased from 66 to 58 kJ/mol. INTRODUCTION Due to the increasing demand of copper, low grade ores and refractory minerals like chalcopyrite are expected to become the main copper source in the next years (Klauber, 2008). As a low-grade sulfide, chalcopyrite shall be processed hydrometallurgically. However, due to the formation of a protective layer of elemental sulfur during the oxidizing leaching, the dissolution of copper is slow and/or incomplete (De Bernardi and Carlesi, 2013). Therefore, the development of new technologies to enhance the extraction of copper from chalcopyrite is highly required."

Jan 1, 2018

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change due to the complex interdependence of metals, both in production and recovery, and the strong path dependency of industry and infrastructure development. Therefore, models for dynamic simulation were constructed that allow the specification and evaluation of the metal process network and waste management infrastructure ‘products’ over a longer time span. The model has been constructed using a bottom-up approach, to enable assessment of the environmental aspects of metallurgy and to simulate changes in the system structure and technology, i.e. from reactor or individual process step up to integrated material cycles. The model comprises hierarchical mass balances and linear models of individual processes and sub-processes. Thus, at lower system aggregate levels an increasing level of technical detail is represented. Data reconciliation has been used literature data on process feed, products and residue composition to calculate representative and reliable split factors around each (sub-)process. World production figures on process capacity and recovery rates are be used to calculate the relative contribution of processes. The dynamic map is illustrated with a case on the introduction of lead-free solder.

Jan 1, 2003

By V. G. Prikhodko, G. I. Sukhinin, I. V. Yarygin, A. V. Fedoseev, S. A. Novopashin

"The first experiments on the vacuum drying of spherical clay sample are presented and the theoretical model of the process is considered. The model is based on the solution of the heat and the moisture transfer equations with the effective thermal conductivity and water diffusion coefficients for wet porous clay-like medium. The time and radial dependence of the temperature and the moisture were calculated for different initial conditions. The results obtained for the time dependence of the moisture content are in good agreement with the experimental results obtained in the initial period, when all the moisture in the sample did not freeze to form an ice crust. INTRODUCTION Capillary-porous materials very often occur in nature and in industry. A porous medium is a solid matrix with voids, or pores, which are continuously connected. These pores are usually filled with fluids or moisture, water vapor and air that can pass through the medium because the voids are interconnected. The void fraction in the solid matrix is referred to as the porosity. Porosity or void fraction is a measure of the void (i.e. ""empty"") spaces in a material, and is a fraction of the volume of voids over the total volume. The moisture content in porous media determines the properties of the porous body, its mechanical and thermo-physical properties, such as density, plasticity, viscoelasticity, swelling, cracking, and so on. Complex processes of heat and mass transfer occur in porous bodies when they are heated or cooled, during drying or freezing (Luikov,1966). The course of these processes depends essentially on the physical-chemical composition of the solid matrix of the porous body, on its fractal dimension, porosity and morphology. The clay and clay minerals are the most important porous materials in the history of the mankind (Mukherjee, 2013). Clay is a very fine grained, unconsolidated rock matter, which is plastic when wet, but becomes hard and stony when heated. It has its origin in natural processes, mostly complex weathering, transported and deposited by sedimentation within geological periods. Clay is composed of silica {SiO2), Alumina (Al2O3) and water (H2O) plus appreciable concentrations of oxides of iron, alkali and alkaline earth, and contains groups of crystalline substances such as quartz, feldspar, and mica. Building materials, bricks, and tiles, pottery, porcelain and faience are made from clay. Clay is used in the food and medical industry, and, not least, in the mining industry as a carrier containing aluminum, silicon and other valuable elements, as well as metals (copper, gold) as constituents, contained in the pores in the form of micro- and nano-particles or grains."

Jan 1, 2018

By Crasta Jeason, T. Sreenivas, M. Narasimha

The subtle nature of the flow inside the hydrocyclone has encouraged development of mathematical models for predicting its performance, which are widely used in simulation of comminution circuits. But most of the models available are based on single average feed density. But the feed to hydrocyclone classifier is generally mixture of particles of different densities. This effect of varying density of feed particles on performance of hydrocyclone has been reported in literature. Further investigation of the effect of multi component feed on the performance of hydrocyclone is the objective of this work. This work involves experimental work to study multicomponent behaviour in various size cyclones. The performance of hydrocyclone for feed mixture of magnetite and quartz has been studied. The effect of presence of magnetite, a high density material on efficiency of separation of quartz has been analysed. It was observed that the effect of component interaction increases with feed solids concentration leading to an increased cut-size for a given optimum cyclone conditions. Based on the multi-component exiperiments available in literature, a concept for modeling the performance of hydrocyclones is proposed. A set of semi-empirical model equations for cut-size, sharpness of separation are presented. An attempt to validate the new hydrocyclone model on multi-component behaviour is made.

Jan 1, 2014