Search Documents

By Gene Bryant, Wesley Schmutzler, Matteo Bertoni

The levees where the Mississippi River and the Lower Wood River meet near East Alton Illinois have been a problem area for years due to underseepage. The first phase of the deep cutoff wall was a 2,000-linear foot section that was completed in 2016 for the Illinois Flood Prevention District Council. This section was installed along the Wood River and the Mississippi river to depths of over 135’, The United States Army Corps of Engineers was tasked with continuing the cutoff wall along the Mississippi river. The wall was a continuation of phase I with depths up to 140’. The 1,000’ long cutoff wall was installed through fill, loose sands, cobbles, and sandy clay. The cutoff wall was terminated in either Glacial Till or sound rock. In order to provide wall permeability equal to or less than 1.0 X 10-6 cm/sec a self-hardening slurry (SHS) composed of ordinary Portland cement, slag cement, and water was utilized. The depths reached on this project using SHS is the deepest done to date in the United States. Along with the permeability requirements, a very narrow range for the unconfined compressive strength was specified at 50 – 180 PSI. In order to monitor the ground movement and water level fluctuations during the excavation of the panels with the Hydromill or Clamshell, 6 automated inclinometers were installed and monitored continuously during panel excavation in phase 1. Seven automated piezometers were monitored in phase 2. This paper will give an overview of the project with emphasis on the effect of the excavation on the instrumentation, specifically the reaction of the piezometers as the last panels were installed. INTRODUCTION The project is in Illinois, about 1000 feet downstream from where the Wood River Creek enters the Mississippi River between East Alton, IL and Wood River, IL adjacent to State Highway 143 (Fig. 1). The Wood River Lower Cutoff Wall Phase 2 Project (WR2) was awarded to TREVIICOS SOUTH (TIS) in September 2017. The Main Project features are: Construction of work platform, inclinometers installation and removal, cutoff wall construction by the Self-Hardening Slurry method (approx. 135,000 sf) up to 140' depth, clay cap installation, and site restoration. The levee system along this stretch of the Mississippi River has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed to ensure that Levee failure would not be an issue in the future.

Jan 1, 2019

By Glen R. Andersen

"Two of the greatest challenges we face in managing our aging infrastructure are to perform accurate condition assessments and to realistically predict the risk of non-action. The aim of this paper is to discuss common pitfalls we face in performing accurate condition assessments of our aging infrastructure using the case history of a recent near miss at the Lake Manatee Dam in Central Florida. The dam was placed into service in 1967 and was inspected every couple of years by dam safety engineers beginning in 1978. Although there was substantial and repeated evidence of a serious piping and internal erosion problem in each of these inspections, the problem was overlooked by most of the inspection teams. In 2012, the inspection team concluded that: “the Lake Manatee Reservoir Dam is well maintained and is in very good overall condition.” However, in 2013 a new team inspected the dam from an entirely different perspective, identified potentially serious conditions, performed an integration of the historical inspection data and concluded that: 1) the Lake Manatee Dam was in a severely distressed state; and, 2) without an immediate intervention there was a high risk of an uncontrolled release of the reservoir most likely following a large rainfall event and prolonged opening of the service spillway. This case history highlights human factors contributing to the near miss including group think and focusing on changes from prior inspections. The integration of historical inspection data is recommended for managing our aging infrastructure.INTRODUCTIONThe engineering analytical techniques most appropriate for assessing an aging infrastructure can be distinct from those used for the original design. To adequately manage our aging infrastructure it is necessary to change our perspective from anticipating failure mechanisms and designing to prevent them to assessing condition, detecting the presence of potential failure mechanisms, and assessing the potential risks. In many circumstances the failure mechanisms currently active may not have been anticipated by the original design team.We have developed a substantial body of experience in the design of our infrastructure. Full scale and laboratory testing coupled with the application of scientific principles to model behavior has led to many powerful design tools. The continued serviceability of our infrastructure as its elements reach their design lives stands as a legacy to our profession. However, under the sustained effect of limited resources for maintenance and rehabilitation parts of our infrastructure are in a highly deteriorated state. Unfortunately, the condition of some of these has not been properly assessed. This paper focuses on the Lake Manatee Dam in Central Florida and the process used to clearly identify its highly deteriorated state. While there are many factors that contributed to the lack of a proper assessment of its condition, the focus herein will be on human factors and in particular how “Group Think”, “Aversion to Bad News”, and “Condition Assessments Based on Changes to Prior Condition” may have contributed to not properly identifying the development of a serious failure mechanism."

Jan 1, 2017

By Dominic Ammon, Mark Rothbauer, Paul Landers P. E.

Across the Potomac River from the location of the DFI47 Annual Conference (October 2022), in Alexandria, VA, two large permanent anchored walls with a decorative shotcrete face were recently constructed for the North Hill project, a new multi-family and townhome development. The project was executed with a design-build approach for the Fairfax County Redevelopment and Housing Authority with review by the Fairfax County Geotechnical Review Board. The project was constructed in highly variable Potomac group sediments that include high plasticity clay/silt terrace deposits overlying coarser grained materials. The soils were over consolidated and exhibited potential for slickensides from relief of horizontal stresses from past erosion. The wall system was designed to include deep soldier piles and permanent long strand anchors considering past slope instability in the area. As the construction progressed, problematic soil conditions and water issues required modifications to drilling methods. The two permanent walls spanned 800 and 1,000 feet long with a maximum height reaching 40 feet.

Oct 1, 2022

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

Large diameter open-end pipe piles are increasingly used as deep foundations to support heavy onshore and offshore structures. During the driving process, several factors such as subsurface conditions, hammer type, hammer efficiency, pile type, plug conditions, temporarily increased base resistance, and loss of shaft resistance have direct impact on the driveability of large diameter open-end pipe piles. In a uniform subsurface condition, the unit shaft resistance increases with depth. Consequently, more resistance is accumulated as piles penetrate to greater depths which results in higher driving resistance. However, according to the friction fatigue analysis, the greater the number of shearing cycles occurring on a soil segment along the pile shaft, the greater the reduction of its shear resistance. As a consequence, since upper soil layers are subjected to a greater number of blows than those at greater depths, they have a relatively lower resistance compared to what would be calculated with standard geotechnical analysis methods. As a result of this progressive and nonuniform loss of shaft resistance with driving, blowcounts tend to increase at a lower rate than expected from traditional analyses. This paper discusses one of the approaches to the driveability analysis with the geotechnical friction fatigue consideration. It also shows comparisons between predicted driveability obtained from wave equation analysis and field driving records. All analyses were performed for a 2.134 m (7.0 ft) diameter open-end pipe pile installed at a total depth of 192.90 m (554 ft). Two separate static resistance and wave equation analyses were completed for the case study presented in this paper: 1) Friction Fatigue analysis based on the recommendations of Alm and Hamre (2001), subsequently referred to as the FF model, and 2) Standard Driveability analysis based on soil set- up factors, hereafter referred to as the SD model in this paper. Results from analyses included the shaft resistance distributions compared to the result of the signal matching analyses determined from the pile dynamic measurement. Furthermore, predicted blowcounts were compared to observed blowcounts during the pile driving. The comparison analyses indicated a 54.4 percent resistance loss of the Static Resistance during Driving (SRD) due to the geotechnical friction fatigue corresponding to a 46 percent reduction in total resistance. The analyses also showed that average predicted blowcounts using the friction fatigue were 6.4 percent lower than measured blowcounts, whereas, the standard driveability approach showed 42.1 percent higher blowcounts compared to the blowcounts shown in the driving log values.

Jan 1, 2019

By Michael Forrest, John Roadifer, Glen Gorski

"The Calaveras Dam Replacement Project (CDRP) requires large disposal sites to store excess excavated materials that could not be utilized for dam construction. Because of access restrictions during design, the disposal site rockfill toe dike area at the edge of the reservoir could not be explored to evaluate soil conditions. As such, the site had to be explored as part of the construction contract. Exploration revealed very soft clay and loose silty sand up to 40 feet thick that would not be able to support the rockfill dike at the toe of a large disposal site fill. Several alternatives were evaluated to stabilize these soils. Based on constructability, cost and risk considerations, cement deep soil mixing (CDSM) was selected as the preferred method of soil stabilization. The challenge was to design and construct the CDSM stabilization to minimize construction delays. A joint effort by the design engineer, construction manager and contractor achieved CDSM stabilization in about three months, from design through completion of construction. A rigorous quality control program included compression testing of both wet grab and cored soil cement samples to demonstrate that specified strength requirements were being achieved.INTRODUCTIONDisposal Site 3 (Figure 1) is one of the primary CDRP disposal sites having a height of 240 feet and a storage capacity of about 2,500,000 cubic yards. An approximately 40-foot-high rockfill dike at the base of the disposal site provides an erosion resistant toe for the disposal site. The rectangular foundation area shown in red was not able to be investigated during design because of access restrictions."

Jan 1, 2015

By Madan Kumar Annam, Hari Krishna Y, I. V. Anirudhan

"For completion of projects in time with positive results, improvements of productivity and effective project management procedures have become extremely important. This paper discusses a milestone project comprising 198 residential units of stilt plus 4 levels that highlighted the benefits of these key aspects. Success of ground modification procedure benefitting the entire cycle involving End Users, Suppliers, Bankers and Developer is discussed.Soil profile for a considerable depth comprises weak layers of silty clay and sandy clay with varying consistency. Deep foundations have been an automatic choice of foundation for major buildings constructed in similar environment. After serious geotechnical appraisal, reconsideration of the foundation system with an alternative solution of Ground Improvement was found to be optimal in terms of Cost and Time. Full raft foundation on the improved ground by installation of Vibro Stone Columns (dry bottom feed method) was considered as an alternative foundation system. The ground improvement works were completed within 6 weeks (as against 6 months to that of pile foundations) that was made possible through effective project management. Full size plate load tests were conducted to ascertain effectiveness of the ground improvement works. Success of the foundation system was proved by full scale monitoring of foundation settlement during and after completion of the project over a span of 2 years. This paper describes design considerations, quality control in the construction of Vibro Stone Columns (dry bottom feed method) and performance monitoring of the project thereafter.INTRODUCTIONGenerally in weak deposits, deep foundations like bored cast-in-situ piles and driven piles have historically been the foundation choice for major buildings and other structures. Construction of pile foundations is becoming a challenge due to their high cost, large construction time and due to severe environmental issues (noise pollution, ground vibrations and carbon footprint). Since the proposed building complex is located within the proximity of a well-developed residential locality, objections raised by neighborhoods to pile driving activities called for a rethinking on the foundation system.The top 6m to 8m of soil profile comprises of silty clay / sandy clay having highly varying consistency. GWT was encountered at 3.0m below the existing ground level. Under this situation, the reconsideration of the type of foundation system with respect to the geotechnical analysis gave a thought to assess feasibility of ground improvement system."

Jan 1, 2015

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022

By Michael Frawley, Deana Ruud, Jessica Turner

Technology is allowing for new ways to mitigate risk associated with subsurface exploration and unanticipated subsurface conditions during construction. Unanticipated subsurface conditions have the potential to force delays and cost overruns on even the best-managed and well-executed projects. For more than a century, geotechnical professionals have documented the location and conditions encountered in hundreds of thousands of subsurface borings. Utilizing processes for compiling and managing data, owners can streamline site selection and receive access to a conceptual geotechnical model before field exploration takes place. Digitizing historical subsurface information allows for creation of an interactive, web-based platform combining publicly available information and culminating with the opinion of a local, experienced geotechnical engineer. This connectivity aids in the reduction of risks associated with unknown conditions on prospective project sites. Through this conceptual project study, we demonstrate how a project owner would be able to use a comprehensive desktop study to review the expected conditions prior to making a purchasing decision. Following the purchase, the expected conditions would be confirmed through traditional methods, confirming potentially problematic site conditions and the associated risks. INTRODUCTION Preliminary project planning is often based on assumptions made by the design team with regards to site suitability. After due diligence, site development is traditionally initiated by the owner or the owner’s representative when engaging a geotechnical engineer to perform a thorough subsurface exploration at a site. The data generated by the geotechnical engineer’s analysis of the site is required to design foundations, pavements and earth retaining structures and move the project from concept into design. This necessary, subsurface exploration can be time consuming, intrusive, and require significant resources, often when resources during construction seasons when resources are most limited. By leveraging historical data generated from previous subsurface exploration, a more thorough analysis of project risk can be developed prior to mobilizing a drill rig. Ultimately, preliminary budgets and designs are more accurate and geotechnical field exploration is more strategic. The geotechnical engineer’s role transforms from raw exploration and analysis to confirmation of anticipated conditions.

Jan 1, 2019

By Negin Khalili-Motlagh-Kasmaei, Paul O'Leary, Christopher J. Rothsiedl, Dimitar Ninesvski, Alexander Zöhrer, Vincent Winter

This paper presents the implementation of a digital twin for the vibro-replacement ground improvement process, as part of a digital construction site. The goal is to implement an evidence-based quality assurance for each produced element (column or point). The system uses a combination of planning data and real-time machine data collected automatically from construction equipment. In addition to the quality assurance, feedback is provided in a number of areas, e.g., condition monitoring of the equipment. The digital twin builds upon the real-time sensor and machine data, fused with metadata, to implement a digital model for the process. A hierarchical data evaluation, using rule-based Key Performance Indicators (KPIs), permits viewing of the spatial variation of data over the construction site. This permits the modelling of systematic variations in subsurface properties across the site, enabling the detection of anomalous individual elements, the diagnosis of their cause and the prediction of properties as construction proceeds over the site. All time-series data and KPIs are represented by standard classes of objects, leading to a generic coding of the data analysis; this minimizes the effort required to add additional sites and/or new KPIs. Examples are presented for a number of sites, where the system was used to identify anomalous columns.

May 1, 2022

By Frank Rausche, Scott D. Webster, Rozbeh B. Moghaddam

"Pile foundation driveability is a function of several variables such as subsurface characteristics, hammer type, hammer efficiency, pile type, and plugging conditions. One important phenomenon occurring during pile driving, and yet not well documented and published, is the friction fatigue, where a reduction of shaft resistance is observed as the pile is driven to greater embedment. This paper introduces current soil models developed for the assessment of friction fatigue, and further presents a comparison between predicted driveability obtained from Wave Equation Analysis Program (GRLWEAP) and field driving records. From a literature survey, and review of technical articles, a widely-used soil model known as AH-01 has been selected to analyze the friction fatigue concept. Using a WEAP software, two driveability analysis were completed using the standard approach with setup factors, and adapting the AH-01 model into the WEAP input file. Driveability predictions were compared to the driving records corresponding to a 1676-mm x 44- mm open-ended pipe pile with a total and embedment lengths of 180-m and 119-m, respectively. Results from analyses and the comparison presented in this paper provide further information regarding existing methods for the incorporation of the friction fatigue concept to the driveability analyses, and contributes to a better prediction of driveability of open-ended pipe piles. IntroductionDynamic measurements during pile installation provide more dependable information as compared to results obtained from predictive models used for design. Despite uncertainties associated with a specific project site and foundation type, measured data provides a reliable understanding of the soil resistance and its distribution throughout the length of the pile. Back-calculations or back-analyses based on a series of measured data from a pile driving process could help to obtain reliable models to better predict events related to pile installation process in spite of all variability related to fitted models. One of the widely-used analysis regarding pile driving during the design phase is the “driveability analysis” where capacity, blowcounts, maximum stresses in the pile element, and transferred energy from the hammer to the pile element are predicted using mathematical models along with a software. Such analysis requires relevant information regarding soil, pile, and hammer properties combined with a deep understanding of the level of impact each one of these properties could have on the analysis."

Jan 1, 2017

By Rachael M. Fischer, Daniel J. Woeste, Terence P. Holman

"A new 50 MW biomass renewable energy power plant was planned for construction in southwestern Georgia. The original foundation design consisted of very conservatively designed H-pile groups with vertical and battered piles to carry the axial and lateral loads. The authors conducted a testing program to value-engineer the foundations with the goals of increasing the working axial pile resistance and reducing or eliminating battered piles. Seven test piles were installed and dynamically monitored with a Pile Driving Analyzer (PDA). Two lateral load tests and one tension load test were conducted. The results of our testing program allowed the project team to: (i) increase working pile resistances by factors of 1.5 to 2, reducing the total number of piles by more than 30%, (ii) eliminate the battered piles, and (iii) lessen overall project risk. Poor communication and documentation in a critical area of the site required some piles to be spliced and re-driven after additional PDA testing, establishment of new driving criteria, and consideration of longterm soil setup. This case study emphasizes the economic and risk reduction benefits of a design phase testing program, and the need for consistent communication between parties in the field.INTRODUCTIONA new 50 MW biomass renewable energy power plant (Plant) was planned and constructed in southwestern Georgia. The Plant converts clean wood-based and paper-based waste from existing forestry and pulp operations, waste timber, and maintenance operations into steam that is used by an adjacent manufacturing facility. The Plant also generates electric power with limited greenhouse or particulate emissions for use by a local utility provider.The project site (Site) is located in Dougherty County, in the Coastal Plain physiographic province of Georgia; an area of known karstic activity. Specifically, the Site is underlain at depths of 30 to 45 ft by the Ocala Formation, a light-colored fossiliferous limestone of the Eocene era. According to Watson (1981), the Ocala Formation is 125 to 200 ft thick in the vicinity of the Site and increases in thickness to the southeast. Due to differential weathering, this formation is characterized by an irregular upper surface that transitions from sandy clay/clayey sand into a dense to very dense silt and fine sand locally referred to as limestone. This subsurface stratum is most relevant to the foundation design of the Plant."

Jan 1, 2016

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By Karen Talbot, Noah Maier, Rob Jameson, Giuseppe Gaspari

A storage and drainage tunnel advancing below I-75 in Detroit, Michigan experienced sudden subsidence. The Tunnel Boring Machine (TBM) was damaged to the extent that its shield, cutting head and extensive interior components needed to be extracted and replaced along with several completed tunnel segments. The tunnel was 16 feet (4.9m) in diameter with crown over 79 feet (24m) deep at the time. The tunneling contractor immediately engaged their designers and specialty subcontractors to develop a scheme to access the machine and repair the tunnel. They required a shaft 99 feet (30m) deep, with unobstructed plan dimension of 50 feet (15m) to accommodate the large components that needed to be removed and replaced. This precluded the application of an internally braced excavation and instead earth support solutions focused on use of a compression ring. Since the completed tunnel section behind the TBM obstructed closure of the compression ring below its invert, this paper describes the innovative access shaft solution employed. A conventional compression ring was constructed using 5 feet (1.5m) diameter drilled shafts down to the tunnel crown. In front of, and to the sides of the tunnel heading, the secant shafts were extended to over 150 feet (46m) depth, creating a horseshoe of support extending 50 feet (15m) below the planned excavation invert. Larger diameter "King Pile" shafts were drilled immediately to either side of the tunnel, overlapped into each end of the secant "horseshoe". The king pile shafts, together with a heavily reinforced ring beam above the crown elevation, acted as a door frame to transfer hoop loads from the incomplete secant arc into reaction supports above and below the tunnel. These oversize king pile shafts were extended and socketed into rock over 70 feet (21m) below tunnel invert. Very tight installation tolerances were necessary to maintain secant shaft alignment to depths exceeding 150 feet (46m). The project operational, geotechnical, and quality data was managed and visualized using a custom GIS interface. This paper will present the design approach employed and review the construction and quality program selected to repair the tunnel.

Oct 1, 2022

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022