Search Documents

By François Charette

High stress conditions in underground mines push the performance envelope of support systems to their limit. In weak rock masses these conditions lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock and support failure. In typical support systems, a combination of different reinforcement and support mechanisms provide the required convergence control and retainment. These systems usually involve a multi-pass support installation. The advantages of a single pass support system are investigated and several bolting combinations are compared. Criteria for design are reviewed and new criteria are proposed to include cost and effectiveness in commonly used engineering approaches. Field observation and testing is used to illustrate the difference between the proposed approach and more conventional systems.

Nov 1, 2011

By Robert Walker

Agenda ? Investment thesis ? Engagement ? Competitive advantages Corporate engagement ?The ESG Services team carries out engagement activity with the companies in the Ethical Funds portfolio on behalf of investors ?Each year about 50 companies (20% of our assets) are placed on our Focus List based on assessment of significance and severity of ESG risks and the extent of our portfolio exposure ?We engage in direct discussions on material ESG issues ranging from climate change to human rights to executive compensation ?This enables the team to gain insight into how management is addressing various risks to the business and encourage positive change where gaps exist

Aug 1, 2013

By W. Yang, R. Rajasingam, B. Tadesse, K. Mohanarangam

Copper electrowinning is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. Acid mist is produced by these oxygen bubbles bursting at the electrolyte free surface. It is an undesired by-product of the Electrowinning process which unchecked could result in mist generation higher than the recommended time-weight-average exposure limit. Various approaches to alleviate the problem have been adopted by companies, all with varying degrees of success. All of these have been attempts to treat the symptom acid mist rather than the inherent problem, often proving expensive and, in some cases, ineffectual. In this paper, a new method was developed for acid mist quantification based on ‘total acid mist’ capture above the EW cell under well controlled conditions. With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables including current density, flow rate, temperature, etc. independently and their effect on bubble size, bubble velocity, gas hold-up as well as acid mist generation and its droplet size. Results show that total acid mist capture increases with an increase in current density but remains more or less constant between 300–500 A m-2. Total acid mist also shows an increase with increasing electrolyte temperature. These findings are substantiated with the aid of bubble size and gas hold-up measurements with the transparent EW cell.

Jan 1, 2019

By M. Takebayashi, M. Shingu, H. Nagai, T. Nakai, S. Asano

The Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. (SMM) is located in the coastal zone of Saijo City and Niihama City, Ehime Prefecture, Japan. The refinery has been producing copper, sulfuric acid, and precious metals such as gold, silver, and PGMs. Previously, the process of precious metals recovery was a combination of pyrometallurgy and an electro-refining process with the conventional cupellation for around 400 years. However, this process had some major problems such as non-efficient recovery of valuable metals, high environmental risk by pyrometallurgy, high cost for maintenance of equipment and so on. In order to solve these problems, a thorough hydrometallurgical process for precious metals refining using chlorine leaching technology was originated and developed by Sumitomo and thereafter commercialized in 2004 at Toyo Copper Smelter and Refinery. This new process enabled shorter-term recovery of gold and manpower saving, and occupational safety and working conditions have also been improved. Superiority over the existing hydrometallurgical processes was also confirmed, for example by the achievement of 99.99% pure silver production without an electro-refining process. This paper summarizes the hydrometallurgical technologies for precious metals recovery such as chlorine leaching of copper anode slime for silver recovery, solvent extraction (SX) for gold recovery, and ion exchange (IX) for PGMs recovery. It also presents a unique silver purification process. INTRODUCTION Sumitomo Metal Mining Co., Ltd. (SMM) produces copper, precious metals and rare metals as by-products at the Toyo Copper Smelter and Refinery, and nickel and cobalt at the Niihama Nickel Refinery. Precious metals contained in nickel ore are also separated and refined at the Toyo Refinery after concentration. SMM has been refining precious metals using the pyrometallurgical method. In recent years, we have revamped the separation and refining process of precious metals dramatically by making use of advanced hydrometallurgical and engineering technology developed in the company. In this paper, we introduce the history of development and techniques of this process, and also introduce in detail the technologies of gold refining, PGMs recovery, selenium recovery, and silver refining which have been particularly difficult to achieve.

Jan 1, 2019

By D. J. MacKinnon

Zinc metal was first produced in India around 1100 A.O. and a zinc industry based on retorting gradually developed in both India and China(1) . The vertical retort method for smelting zinc ores was developed in England in the 1730s; this was followed by the more fuel efficient horizontal retort process developed by the Belgians in the 19th century(2) . The horizontal retort process was the standard method of zinc manufacture until the 1950s when it became obvious that it could not compete with electrolytic zinc technology(2). The present day extractive metallurgy of zinc is dominated by the electrolytic process which now accounts for almost 80% of the world's primary zinc production. In recent years the electrolytic zinc process has seen significant improvements: the fluid-bed roasting of zinc concentrates, improved leaching and residue treatment techniques such as the jarosite and goethite processes, improved solution purification procedures, mechanization of the zinc electrolysis step and of the zinc melting and casting operation. In addition, new leaching processes have been implemented for the treatment of oxidized ores, particularly silicates, and the pressure leaching of zinc sulphide concentrates is now a commercial reality. Although the electrolytic zinc process was first used on a commercial scale in 1916, its history can be traced back to the 1860s. The purpose of the present paper is to outline the early history of the electrolytic zinc process and to trace the significant developments which led to the first successful commercial electrolytic zinc plants.

Jan 1, 1999

By G. Beckstead, L. Gormely, R. Zimmer, K. Hanneman, B. Nethery

As part of the EIS and permitting activities for the Pogo Mine in Alaska, a risk assessment study for the water management plan was carried out. The basis for the study was a site water volume and contaminant balance model. Probabilistic modeling was carried out using the @Risk Monte Carlo simulation package to investigate the frequency, quantity, and quality of discharges under varying assumptions. The results were used in discussions with regulatory officials as part of the permitting process for the project. The simulation allows probabilistic modeling of key environmental parameters based on input frequency distributions involving both quality and quantity of flow. When combined with predictions of water treatment plant capacities and removal efficiency, this was very useful for defining the likelihood of important regulatory outcomes. Based on the model, certain project modifications were made. Using the simulation as a basis, ongoing dialog with regulators led to consensus that all potential risks have been considered and mitigated for the Pogo Mine according to their likelihood and severity, and that regulatory requirements would be achieved. The paper describes the model and some of the applications for which it was used.

Jan 1, 2005

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By I. Silin, M. Stapelmann, H. Wotruba, K. M. Hahn, C. Gerold, J. Katzmarzyk

New deposits are often characterized as low-grade and complex ore bodies. To date, processing of fine grained ore deposits implies complex processing routes with high energy consumption. For that reason, the investigation of dry grinding, e.g. with vertical roller mills (VRM), is an approach to save energy reserves. It is already proven that dry grinding can influence subsequent processing steps. In terms of flotation, the surface characteristics of the minerals are crucial for a successful flotation process, e.g. the sufficient adhesion of mineral particles and air bubbles. Wet grinding results in different surface properties of the product entering the conditioning stage than dry grinding, which has direct influences on the subsequent flotation process. To investigate the consequences for flotation, processing of a copper sulfide ore containing chalcopyrite and bornite was investigated, including grinding and rougher flotation. The effects of wet tumbling mill and dry VRM grinding on the degree of liberation of valuable minerals are characterized using mineral liberation analysis by scanning electron microscopy. The obtained flotation results, as well as the recorded flotation parameters such as dissolved oxygen, oxidation reduction potential and conductivity are presented and discussed. INTRODUCTION Copper production is mainly connected to porphyry copper deposits as main source for copper sulfides such as chalcopyrite and bornite. State-of-the-art processing of these deposits is already established worldwide for decades, combining crushing, fine grinding and subsequent flotation with rougher, cleaner and scavenger stages (del Villar, Desbiens, & Maldonado, Bouchard, 2010). While the demand for copper is increasing, copper grades of the deposits are decreasing and the remaining ore bodies have more complex mineralogy and finer particle size distribution. This implies processing routes with high water and – due to the liberation of fine grained valuable minerals – high energy consumption by fine grinding. One of the main energy consumers in processing plants is the grinding section, which accounts for more than 50% of the energy consumption in processing plants and even 4% of the worldwide energy consumption (Jeswiet, & Szekeres, 2016). Therefore, dry fine grinding alternatives are applied to enhance the overall energy consumption of mineral processing plants: high pressure grinding rolls (HPGR) and vertical roller mills (VRM).

Jan 1, 2019

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By David J. Forrester

Light metals, most commonly aluminum, magnesium and titanium, and alloys containing them, are used in many industrial applications where lightness, hardness, ductility and resistance to corrosion are needed. However, these metals and their alloys can be potential ignition sources in underground coal mines. There have been documented cases in the past where coal mine explosions have been attributed to firedamp/coal dust ignitions involving light metals or their alloys. When light metals and their alloys are brought into contact with oxygen bearing material, such as iron oxide (rust) in the presence of heat, then a "thermite" reaction can occur. This source of heat can be generated from frictional contact or from merely a glancing blow. This paper outlines the hazards associated with light alloys, how to address the hazard and regulatory aspects.

May 1, 2001

By S. Balideh

A good understanding of the behavior of broken rock helps to make more informed decisions regarding slope stability and waste dump issues in mines. The cohesion coefficient of rock has little influence on the strength of broken rock; therefore, a criterion based on friction and cohesion of intact materials does not provide an accurate analysis for the strength of broken rock. This paper illustrates the effective strength of broken rock through a brief literature review about failure of intact rock and rock masses. The complete stress- strain curve and some important points of residual strength of rock are summarized in this paper.

Jun 1, 2012

By Robert D. Irvine

"Enhanced concern for protection of the environment and attendant actions by environ-mental regulatory authorities in support of this concern are influencing, to varying degrees, the demand and supply of a range of industrial minerals in a number of jurisdictions. These influences take a variety of forms.In this paper, the author seeks to delineate certain broad trends which are occurring relative to industrial minerals and the environment and then, through a series of examples, to outline opportunities, developments, and impacts respecting a number of industrial minerals produced and consumed in Canada and the United States."

Jan 1, 1996

By P. A. Christopher, R. H. Pinsent

"The Adanac molybdenum porphyry deposit near Atlin, in northwestern British Columbia, was discovered in 1905. It was explored extensively between 1967 and 1980.The deposit is within a complex, multi-phase, quartz monzonite stock that is a satellite of the post-accretionary, Surprise Lake Batholith. Biotite K-Ar dates range from 703 ± 2.4 Ma to 71.6 ± 2.1 Ma, indicating a Late Cretaceous age of emplacement.The deposit comprises an irregular-shaped ring or halo peripheral to a quartz monzonite porphyry dome, or ""cupola': The shape of the ring, and of a smal~ fine-grained quartz monzonite intrusion, and the presence of higher-grade mineralimtion on the eastern flank of the cupola, suggest partial control by a preminera/ structure. The deposit is truncated by a steep, northwesterly dipping, normal fault (Adera Fault) that down-dropped the northern half of the deposit by a minimum of 100 mThe deposit lacks strong zonal alteration but there are narrow envelopes of potassic alteration around some veins and local zones of intense wall-rock silicification. There is considerable retrograde alteration along postminera/ faults and fractures.Molybdenite occurs in veins and fractures, many of which are relatively flat-lying. They occur in all phases of quartz monzonite. Molybdenum is the only element of economic significance. There are vein and skarn occurrences with tungsten, tin, lead, zinc and precious metals peripheral to the deposit.In 1981, Placer Development Limited reported an ""undiluted mineable mineral reserve"" of 151 971 000 tonnes grading 0.063% Mo at a cutoff grade of 0.04% Mo and a strip ratio of 1.5:1."

Jan 1, 1995

By Jaana Romppanen, Satu Jyrkönen, Tiina Ranki, Peter Björklund, Markku Lahtinen, Kaj Eklund, Päivi Suikkanen

Outotec is continuously developing our existing process equipment and new equipment solutions to enhance the Flash Smelting process. Thanks to the long operating history of the Outotec Flash Smelting process feedback from the numerous operating references are available and is utilized. The general goals for development work are to improve equipment performance, thus realizing savings in Smelter plant operation costs by increasing the process efficiency and online availability. Digitalization also opens new possibilities for the feeding equipment and furnace operation monitoring. These solutions will improve the safety and performance of the smelter, and provide process and equipment related information which has not been available earlier. INTRODUCTION The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. The Flash Smelting technology, is now owned and developed by Outotec Oyj and the first plant, is now owned by Boliden Harjavalta Oy. The two companies have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a hot theme/topic during the first days of Flash Smelting, it has nevertheless been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. Along with the process technology development, also development of the equipment has taken place over time. Outotec is continuously working on developing our equipment to better suit the changing need of our customers in the continuously changing operational environment. Orebodies are getting more challenging with lower ore grades and more impurities. Achieving high recoveries for all valuable elements becomes more difficult with high slag quantities and with the need to tackle the high impurity concentrations. There is a need for higher capacities in greenfield and brownfield smelters. The role of the Loss-in-Weight Feeder, the Air Slide and Concentrate Burner is to ensure even feed into the reaction shaft of the Flash Smelting Furnace, and to enable controlling the process well, thereby enabling the best performance for the customers smelter. The design of the Flash Smelting Furnace aims for high availability, long campaign and safe operation.

Jan 1, 2019

By R. G. Achter, E. Wilson

"This paper describes the work undertaken to renovate the Pipe Open Pit drainage system, incorporating measures to improve effluent quality. It describes the technical feat of drilling an l l-inch-diameter hole from the bottom of the open pit for a distance of 1100feet to intersect an underground drift. An innovative method of checking the inclination of this hole is also described. The paper outlines the construction required on the 1500-foot level of the underground mine to facilitate water impoundment and slime settling, as well as the instrumentation for control of water flows. IntroductionThe Manitoba Division of Inco Metals Company operates two mines-an underground mine at Thompson and an open pit at Pipe. The Pipe Open Pit is located 20 miles southwest of the City of Thompson, approximately 400 miles due north of Win nipeg(Fig. 1).Surface diamond drilling of the Pipe ore body was sta rted in 1959. In 1961, a shaft was sunk to a depth o f 1,570 feet to carry out further exploration work and obtain bulk ore samples for metallurgical testing. Site preparation to mine the upper portion of the orebody as an open pit was initiated in 1966 and by late 1967, the removal of silt and clay overburden was in progress. The contractor completed the dredging in the fall of 1969. Over 12 million cubic yards of muskeg, clay and silt was removed, which in some places was 150 feet deep over the orebody. Production began in early 1971, by which time the top three benches of rock had been excavated and the orebody exposed.The Pipe No. 2 Mine main shaft was started in 1970 and completed in 1973 at a depth of 3,160 feet. Development for exploration purposes was carried out on the 1500 and 2460 levels, and permanent pumping facilities were installed.The surface dimensions of the open pit are 2,200 by 1,600 feet, with the long axis striking northeast. The walls are designed with a 45- to 50-degree slope and the ultimate design depth is 720 feet. The present depth of the pit is 520 feet and production capacity is 6,800 tons of ore per mine day."

Jan 1, 1980

By C. Ayora

The Iberian Pyrite Belt (SW Spain and Portugal) contains one of the largest reserves of pyrite in the world with mining activities dating back to prehistoric times. About one hundred abandoned mine wastes and galleries release a huge acidity and metal load to the Tinto and Odiel rivers. Once the mining activity is over, polluting discharges can persists for decades or even centuries with no specific responsible entity. In-situ passive remediation technologies are especially suitable for these orphan sites. The concept is to insert a reactive porous material in the natural flow path of contaminated surface and ground waters, and it is implemented through infiltration ponds and reactive barriers, respectively. Calcium carbonate pea-size gravel is the common alkalinity supplier to neutralize acidity and precipitate metals. These remediation systems have been traditionally implemented in coal mines. However, the acid drainages from the Iberian Pyrite Belt contain metal concentrations one to two orders of magnitude higher than those from coal mines and require special designs to avoid quick clogging or passivation (coating) of the grains of reactive material. To overcome these problems, a Dispersed Alkaline Substrate (DAS) mixed from fine-grained limestone sand and a coarse inert matrix (e.g. wood chips) was developed. The small grains provide a large reactive surface and dissolve almost completely before the growing layer of precipitates passivates the substrate. The high porosity and the dispersion of nuclei for precipitation on the inert surfaces retard clogging. However, limestone dissolution only raises pH to values around 6.5, which is sufficient to precipitate the hydroxides of trivalent metals (Al, Fe), but it is not alkaline enough to remove divalent metals. Magnesium oxide, which hydrates to Mg hydroxide upon contact with water, buffers the solution pH between 8.5 and 10. A DAS system replacing limestone with caustic magnesium oxide has been tested to be very efficient to remove divalent metals (Zn, Cd, Mn, Cu, Co, Ni, Pb) from drainage previously treated with limestone.

Aug 1, 2013

By Moatassem Abdallah

Buildings in the United States account for 72% of electricity consumption, 40% of energy consumption, 13% of water consumption, 39% of carbon footprint, and 30% of waste output. In order to minimize these negative environmental impacts, many public and private owners are requesting that their buildings be more sustainable and certified under the widely known programs such as leadership in energy and environmental design for existing buildings (LEED-EB). To accomplish this, buildings are increasingly integrating green building measures including energy efficient lighting, motion sensors, thermal pane glass, geothermal heat pumps, EnergyStar rated HVAC systems, photovoltaic systems, and wind turbines. This research paper presents the development of an automated decision support system (DSS) that is designed to optimize the selection of green building measures which can be used to upgrade existing buildings. The developed DSS incorporates two optimization models that are capable of (i) minimizing the total upgrade costs required to accomplish a specified LEED-EB certification level such as silver or gold; and (ii) maximizing the number of accredited LEED-EB points within a specified budget of upgrade costs. The DSS is designed to identify a set of optimal upgrade decisions that accomplishes these two optimization objectives. An application example is used to illustrate the capabilities of the DSS and to validate its result.

Aug 1, 2013

By K. Ohto, B. B. Acihikari, H. Kawakita, M. Gurung, S. Alam

Two kinds of adsorbents were prepared from persimmon tannin extract to investigate their adsorption behavior of metal ions from hydrochloric acid solution; one was prepared by treating with concentrated sulfuric acid while another was prepared by immobilizing functional groups of quaternary amine. The former adsorbed only gold(III) and its maximum adsorption capacities was evaluated as high as 1510 g/kg while the latter adsorbed not only gold(III) but also palladium(II) and platinum(IV), the maximum adsorption capacities of which were evaluated as 820, 89 and 101 g/kg, respectively. For both adsorbents, practical adsorption of base metals was not observed.

Jan 1, 2011

By P. E. Walker, M. E. Reed, R. C. Sims, B. Snowdon, D. E. Fallas

An advanced Flash Furnace feed system is the key to improving furnace performance. Clyde-WorleyParsons has developed a revolutionary pulseless pneumatic injection feed system technology, capable of delivering a range of benefits to operators of Flash Furnaces. The solution was created by combining the pneumatic conveying and injection knowledge, expertise and technology of Clyde Materials Handling with WorleyParsons' flash furnace process and operating experience. Optimal furnace burner performance requires the feed material to be presented to the burner as a stable, pulseless and accurately controlled flow, distributed evenly around the burner tip circumference. These simple requirements appear obvious, but are extremely difficult to satisfy in industrial environments and are not achieved by conventional feed systems. Our analysis of existing operating furnaces has identified the link between pulses in concentrate feed rate caused by conventional drag chain conveyors and rapid fluctuations measured in the furnace pressure. These fluctuations occur at a timescale close to the reaction shaft residence time and lead to unwanted instability in the primary furnace reaction zone - the flame. Through the use of the solution created by Clyde-WorleyParsons, it is predicted that the much more accurate control of feed rates achieved can lead to substantial improvements in furnace output, increased oxygen efficiency and better control of the composition of furnace liquids, such as matte, blister or slag. All these improvements lead to significant increases in smelter output and efficiency, and deliver high economic value compared to the cost of the feed system. Clyde-WorleyParsons' solutions can be deployed on greenfield sites or retrofitted, and therefore, have the capability to improve feed control at both new and existing smelters. This paper will discuss the field test work undertaken to date, the impact of findings and the ongoing analysis of linkages between instabilities in the various components of conventional feed systems and furnace pressure stability.

Jan 1, 2007

By D. J. Reddish

The paper describes a case study where numerical modelling has been applied to predict potential risks associated with inflows of water in active mine workings from an overlying sandstone aquifer. The objective of the modelling was to predict the development of strata fractures and strains as the longwall panels were extracted and investigate their relationship to an sandstone aquifer. The numerical modelling study also included the investigation of the effect of mining on a fault that existed close to the start position of one of the panels. The potential effects of mining on the fault were undertaken by parametric studies adjusting properties for the fault and the relative position of extractions, which allowed the mine planner to position the panel layout accordingly.

May 1, 2003