Search Documents

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By Francis Breton, Daniel Larouche, Pierre Heugue, Rémi Martinez

"Nowadays, in order to fit environmental restrictions, automotive markets are demanding cast aluminum alloys working at high temperature (180–300°C). New generations of alloys are required for higher strength components in engine downsizing or start-stop systems which lead to higher loading and higher specific power and stretch current materials to their limits. Recently, transition metals, such as zirconium and vanadium, have been added as alloying elements into an AlSi7Cu3.5Mg0.1 alloy to improve physical, mechanical, thermodynamic properties with the aim of increasing service life of parts. In such alloys, the best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, including: solutionizing, quenching and artificial aging. This study is focused on the modified AlSi7Cu3.5Mg0.1 cast alloy with Mn, Zr and V additions for high temperature application. The characterization of the cast alloy in this study, firstly, helps to evaluate and understand its performance both chemically and structurally according to their physical state: as-cast or as-quenched. Comparison of precipitation kinetics between a binary Al-3.5%wt.Cu alloy and the AlSi7Cu3.5Mg0.1 (Mn, Zr, V) alloy has been characterized by differential scanning calorimetry, TEM observations and micro-hardness testing. The Kissinger analysis was applied to extract activation energies from non-isothermal DSC runs conducted at different stationary heating rates. The study focuses on the impact of the chemical composition such as Si content on the kinetics parameters.INTRODUCTION Pure metal Aluminum shows poor mechanical properties and its malleability is high, that is why alloying elements are added to the mixture before casting to improve physical, mechanical and thermodynamic properties (Javidani, 2015); such as Silicon (Si) for casting properties (castability, cold crack capability, wear resistance, shrinkage behavior), Magnesium (Mg) and Copper (Cu) to generate precipitation hardening systems. Aluminum hypoeutectic alloys (<12% Silicon) with Cu, Mg additions used in the automotive industry for manufacturing mechanical parts (Larouche & Javidani, 2014) are mostly subject, after casting, to precipitation hardening heat treatment (Mohamed & Samuel, 2012) according to specifications and associated standards. The best mechanical properties are associated with the formation of precipitates through an optimum heat treatment sequence, generally including: solutionizing, water quenching and artificial aging (Manente & Timelli, 2011). Hypoeutectic aluminum-copper alloy with amount of Cu around 1 to 4.5wt% is an elementary case for precipitation in heat treatable aluminum alloys. Researchers essentially focused their work on the full precipitation sequence of binary Al-Cu alloy during aging which is presented below."

Jan 1, 2018

By Seunghoon Lee

The increase in the number of higher and larger buildings is expected to require the buildings&apos; outer wall maintenance process, which includes cleaning, painting and monitoring, still depends on manpower. In this study, we proposed the robotic building maintenance system and aimed to reduce the jerk effect through the motion control of the system, improve the performance of the maintenance task, and ensure longer life and safety by improving the stability of the building structure and robot system. Through the results of the motion control and field-test with the proposed system, in specific, horizontal sliding module (HSM) showed that the jerk oriented by impact force was significantly reduced, feasibility of the proposed method was verified, and the robotic challenges were explored.

Aug 1, 2013

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By F. Nava-Alonso, E. Pérez-García, A. Uribe-Salas, J. C. Fuentes-Aceituno, A. A. González-Ibarra, E. N. Castillo-Ventureño

"Precious metals cannot easily be recovered from tellurides by the standard cyanidation process. This work assesses the cyanidation of synthetic samples of precious metals tellurides and explores some alternatives for the leaching of these species (i.e. cyanidation in presence of lead nitrate and thiosulfate leaching). For this purpose, three chemical systems were studied: (1) cyanidation of silver telluride and the effect of lead (II) nitrate addition, (2) cyanidation at high alkalinity and high cyanide concentration of a gold-gold telluride sample containing tellurium and tellurium dioxide, and (3) thiosulfate leaching of silver telluride employing cupric sulfate as oxidant and EDTA as complexing agent for copper. Results showed that standard cyanidation dissolves 10.5% of silver from silver telluride in six hours, while with the addition of 100 mg/L lead increased the silver dissolution up to 100% in the same time. The standard cyanidation of the gold-gold telluride sample dissolves only metallic gold in six hours, while when cyanide concentration and pH were increased, gold and gold telluride were simultaneously dissolved. Finally, thiosulfate leaching dissolves 43.1% of silver from silver telluride in six hours.INTRODUCTION Precious metals tellurides are classified as refractory ores due to the difficulties associated with processing them by the standard cyanidation method. The increasing presence of gold/silver tellurides in some deposits around the world, specifically in Sonora, Mexico, requires new approaches to the cyanidation process, or the development of new leaching techniques. Treatments have been proposed for the recovery of gold and silver from their tellurides, including roasting, preoxidation, cyanidation with lead nitrate, and the use of leaching agents other than cyanide (Zhang, et al., 2010; Ellis and Deschenes, 2016). This work presents preliminary results of three options to recover precious metals from pure tellurides: the cyanidation of gold telluride at high cyanide concentration and high alkalinity, the addition of lead nitrate to the standard cyanidation process, and the use of sodium thiosulfate as leaching reagent."

Jan 1, 2017

By Grant J. Goddard

"The Iron Ore Company of Canada (IOC) has been in operation for over 30 years. Today, and in the future, technology and its application will play an ever more critical role in the company’s business success.The Carol Mining and Concentrating (CMC) division of IOC is energetically applying technology today to enhance performance and results, and is aggressively exploring opportunities to apply technology to support improved business results in the future.A critical area of focus is the application of technology to maintenance management performance. CMC has taken a “back to basics” approach to the fundamentals of maintenance management in 1995 and 1996. In parallel, the mine is aggressively implementing its Vision 2000 maintenance integration plan. This plan is targeted at levering the energies applied to sound maintenance management fundamentals as the company moves to a fully condition based maintenance approach.This paper discusses some of the strategies, key technologies and objectives of theVision 2000 maintenance integration plan at the mining operations of IOC."

Jan 1, 1996

By P. F. Venus

In December 1977, a large pillar was removed by blasthole mining methods at lnco&apos;s Creighton No. 3 mine. Although the 2,363.000-ton blast was not a size record for a single underground blast at Inco, it did represent a significant departure from conventional blasthole mining. In terms of the application of nominal 6-inch-diameter boreholes underground, coupled with bulk slurry explosives, the magnitude of the blast is considered a first and very important development. The application of large-diameter boreholes in underground operations was first tried successfully in 1973. Since that time over 13/4 million feet have been drilled in this adaptation of an open-pit technique to underground operations. The blast, which required 708 holes, totalling 131,500 feet of drilling, was loaded in a six-week period, using special slurry handling techniques developed jointly by Inco and CIL. Inco operating and engineering personnel consider this application of large boreholes and slurry explosives for blasthole mining a very important milestone in modern mining technology.

Jan 1, 1978

By B. J. Morash

"The six mineable coal seams at Quintette Coal Limited (QCL) vary in thickness from 0.75 m to 9.5 m and include waste partings varying from 0.2 m to 4 m thick. They are highly faulted and folded in some areas and dip angles range from horizontal to 90 degrees. Due to this variation in thickness and orientation of the seams, several different mining methods are used to economically recover the coal. The key to QCL&apos;s success depends on the timely collection of detailed geology data and on mine planning which allows selection of the best method of mining to achieve maximum coal recovery with minimum dilution and cost. This paper will describe the various methods of mining employed and the criteria used to select them. IntroductionThe unique challenge in mining at Quintette Coal Limited (QCL) is to extract large quantities of coal and waste, from a complex orebody, with constricted areas for mining and waste disposal. This challenge dictates the mining of as many as four 10 m benches per year, through complicated coal structures, from three separate open pits with a total of 19coal seams. This total is made up of 5 seams at Mesa, 8 seams at Wolverine and 6 seams at Shikano (Fig. 1).Computer-aided mine planning and scheduling is carried out on a routine basis to ensure the prudent selection of methods of mining, to produce plans which ensure delivery of appropriately blended raw coals to the plant, and to coordinate disposal of large quantities of waste.Several methods of mining are applied simultaneously, and as a result coal and waste are released at different rates from twelve to fifteen mining faces. In order to ensure uninterrupted flow of material from excavators and to utilize the truck fleet effectively, a computerized dispatch system is employed.GeologyGenerally, geological conditions can be related to structural (faults and dip angle) and/or stratigraphic (coal seam and interseam waste thickness) sources"

Jan 1, 1988

By Sabine Noelte, Mikko Petteri Rantamäki, Christopher Robben, Anssi Takala, Karl-Erik Rånman

"Sensor-based ore sorting is on its way to establish as a standard option for physical separation. The increasing number of installations in coal, iron ore, industrial minerals and hard-rock metal mining segments underlines the technological and financial potential that is beginning to be untapped. The Ma’aden Phosphate installation with 1.650 t/h sensor-based ore sorter feed sets a new benchmark for the possible capacity of stationary installations. Besides stationary installations, including multiple sorters parallel in different size ranges and multiple stages, containerised semi-mobile plants are applied. These offer two advantages, first being the reduction of transport costs when applied close to the mining face. The second is that semi-mobile systems enable processing of tens of thousands of tonnes of ore in a piloting phase with an approximate duration of 0.5 to six months, verifying the results laboratory mini-bulk tests on 5–10 tonnes of sample. This is especially important for low-grade metal ores because of the inherent Fundamental Sampling Error, as well as the Grouping and Segregation Error. The paper elaborates the results achieved within the I2MINE project, treating polymetallic ore at the Boliden Concentrator in Sweden.INTRODUCTIONSensor-based ore sorting (SBS) is becoming a standard option for physical separation, applied in all segments of mineral production. The Umm Wu’al project sets the bar for stationary SBS installations with 1,650 t/h feed (TOMRA, 2015). TOMRA Sorting Solutions has finalised an agreement in cooperation with Outotec to supply Outotec-branded sorting solutions for the mining and metallurgical industry (TOMRA, 2014). Especially for low-grade hard rock metal ores, an interdisciplinary approach is necessary applying experts for all aspects of mineral production. Due to the impact on the whole process stream, it is important on the end user side to have high level managerial support and involve all disciplines to ensure that all stake holders are involved in the analysis."

Jan 1, 2016

By John E. Udd

The stability of a rock mass is influenced by the presence of discontinuities. In assessing stability, it is required that one should know the frictional and cohesive properties of these contained weaknesses. In the study performed by the authors, a number of samples of diamond drill core containing open discontinuities were tested in shear. The results obtained were compared with values which resulted from back analyses of instabilities in the field.

Jan 1, 1979

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By M. Piard

The scarcity of literature referring to mines in the Rockies has compelled the writer to co-ordinate information and advice taken at the very source. Help was gladly given by active inspectors and mine bosses. Although the field is unimportant at the present time, due to its distance from markets for raw coal, it is quite worthy of the attention it is receiving from two continents; for, with the commercial synthesis of liquid fuels, it would become the largest fuel laboratory in the world, provided, of course, that freight cost drops to a low comparative level. As explained below, there are no obstacles to economical and safe operation under anything like the typical outcrop shown in Figure 1. Although coal dust is probably more dangerous in the Rockies than anywhere else, the damp outcrops afford means of control. The abundant gas may be bled to the open air, and the rigid roof will settle gradually under a wide span of opened outcropping. The Panel Retreating Wall The Measures: Coal measures having an attitude similar to that shown in cross-section in Figure x are characteristic of the active coalfield on the Alberta side of the Rockies, and they are also found on large tracts of undeveloped land west of the divide. The small anticlines, not shown in the cross-section, do not affect the progress of a pillar line, provided their crests are connected to the atmosphere by drainage bore-holes.

Jan 1, 1928

By Edgar A. Manker

"Today&apos;s market for columbium has only developed in the last two decades, and in this sense it is ""newer"" than molybdenum, vanadium and most other steel alloying elements. In this short period, it has assumed a very important role in steel alloying and in superalloys. From a few hundred thousand pounds of columbium in 1960, consumption has grown to nearly 30 million pounds per year, with a market value approaching two hundred million dollars.To assess the outlook for columbium, we will first consider the historical development of consumption and supply, particularly noting that all of today&apos;s major mines were developed during the last two decades. From current production, we will attempt to reasonably project the future. This future may well include new producers, particularly some producing columbium as a co-product with tantalum.The growth of current applications, and emerging new applications, will be considered with regard to future consumption and in relation to future trends in pricing.IntroductionThe nineteenth century was a busy time for the discovery and naming of new elements. Among those discovered were columbium in 1801 and niobium in 1844. Although it was later shown that columbium and niobium are the same element, the two names are still used today. Niobium has been pronounced the ""official"" name by the International Union of Pure and Applied Chemistry, but columbium is still widely used in commercial practice, and we have chosen to use columbium in this paper."

Jan 1, 1981

By T. S. Golosinski

"This paper reviews the types of selective continuous miners (SCMs) available at present, and compares their main features. Furthermore, operating practices and mine planning aspects of the SCMs applications are reviewed and conditions for efficient application of this equipment are defined. Finally, the potential applications of the SCMs in surf ace mining of oil sands are discussed INTRODUCTIONIn the 1970s the United States Bureau of Mines (USBM) conducted a program of investigations, design and demonstration of various continuous surface mining concepts, This included continuous mining equipment which was an adaptation of several civil engineering and/or underground mining machinery concepts to surface mining. Upon termination of this program, the related development was continued by a number of equipment manufacturers, leading to development of several types of SCMs. This new type of surface mining equipment is able to mine selectively hard and thin multi-layered formations at high, sustained, and economically viable production rates.While used mostly in coal mining at present, the characteristic features of this equipment permit conclusion that it may prove to be an efficient tool for surface mining of oil sand, and/or related overburden stripping. Of particular interest here may be the ability to mine thin layers of hard material, without a need for its earlier fragmentation, and the ability of the SCMs to load a variety of haulage equipment, including belt conveyors."

Jan 1, 1989

By William E. Stanley

The paper examines the problems that arise in undertaking socio-economic impact studies to meet the requirements of environmental-impact legislation governing new mine development or expansion. An approach to undertaking socioeconomic impact studies is outlined, responses to specific problems are discussed and ways in which the mining company can use these studies to meet its general objectives are explored. The paper concludes by examining how a socio-economic study, as required by legislation, can be used to assist the mining company in achieving some general objectives it will have in developing a mine.

Jan 1, 1979

By Wenbin Zhang, George W. Poling

"Prior or simultaneous addition of ammonium sulphate can, not only enhance the activating effect of hydrosulphide ions on xanthate flotation of malachite but it can also eliminate possible detrimental or depressing effects of excess residual hydrosulphide . Use of relatively inexpensive ammonium sulphate appears to reduce the consumption of the much more expensive sulphidizing agent for optimal flotation recovery INTRODUCTIONOxidized copper minerals float poorly with conventional thiol-type collectors. This is believed to be due to the nonadherent character of the collector coating, which is readily re- moved by particle abrasion. Rosas and Polingr reported emulsion flotation seemed capable of resisting abrasion during the flotation of non-sulphide copper ores. It appears that the most common flotation technique for oxidized copper minerals comprises sulphidization with Na .S and subsequent treatment by sulphydryl collector. The principles of this method are available . Malghan recently reviewed the studies on the role of sodium sulphide in the flotation of oxidized copper, lead and zinc minerals.It is well known that in the sulphidized flotation of malachite, the activation process depends strongly on the concentration of the sulphidizing agent, i.e., insufficient sulphide gives poor recoveries because of inadequate sulphidization; excessive sulphide also causes poor recoveries due to the depressive effect of the residual hydro-sulphide ions in solution. A major difficulty in sulphidization, especially with a varying feed nature, is to establish and maintain the optimum sulphide concentration in solution. In plant practice, vigorous control of sodium sulphide is required and stepwise addition of the reagent is recommended to improve the efficiency of the process. Soto and Laskowskim have found that malachite, depressed by an excess of sulphide ions, can restore its floatability if air or oxygen is introduced to the pulp. They attributed this to the oxidation of the HS - ions on the surface of the mineral. Jones and Woodcockuvi showed that a sulphide ion selective electrode could be used to optimize the conditions (e.g . amount of hydrosulphide, sulphidization time, flotation time) more readily and precisely than existing methods in the flotation of oxidized copper ores."

Jan 1, 1989

By W. F. Moore

"In January 1981, Quintette Coal Limited (QCL) signed a 2a-year coking coal sales agreement with the Japanese Steel Industry which was followed by the commencement of mining operations in October 1982 and preparation plant operation in November 1983. During the mine &apos;s startup, the town of Tumbler Ridge, the Anzac rail spur line, coal port facilities at Ridley Island plus numerous related elements of infrastructure were completed to support QCL and the neighbouring Bullmose operation in northeastern British Columbia. QCL&apos;s annual product coking coal levels have accelerated from 2.9 to 5.2 Mt between 1984 and 1986 with related increases in total mined volume from 14.8 to 41.0 M BCM between 1983 and 1986. This paper presents an overview of QCL &apos;s current operation and related infrastructure. Development BackgroundDuring the 1970s, the Japanese Steel Industry (JSI) was forecasting a steady and significant growth in its steel production. By 1980 they were expecting crude steel production to increase from about 105 Mt in 1980 to 125 Mt by 1985 and almost 140 Mt by 1990.Discussions between Quintette Coal Limited (QCL) and the JSI for the development of the QCL project began in the 1970s and continued over a period of several years. During that time detailed and regular meetings took place, at which technical and commercial presentations were made to the JSI. The geology of the project area and the alternative mining methods and sequences were studied in detail. The new rail line which would connect the mine to tidewater was a critical factor and received particular attention. Alternate routes for the rail line from Tumbler Ridge to Prince George were the subject of much detailed study and discussions. The Anzac route was chosen in the best long-term interest of the northeast area development, after careful consideration and advice from the Japanese side.The new bulk coal terminal on Ridley Island at Prince Rupert was also a key factor and completed the development of an independent and new major coal field to supply the JSI. The QCL project and the development of the northeast area of British Columbia was a major strategical initiative of the JSI. It provided Japan with an important new coal field which was both self-sufficient and distinct from the traditional Japanese coal field resources in southern Canada, Australia, and the United States."

Jan 1, 1988

By Derek J. Barratt

This paper compares a number of operating conventional and semi-autogenous grinding circuits and analyzes them in regard to operating and capital costs, specifically as applied to porphyry copper ores.

Jan 1, 1979

By Simon Houlding

"Part 1 (CIM Bulletin, August 1991) of this article identified the limitations of the traditional modelling methods and demonstrated the approximations and errors introduced by their application to complex mining situations. The objective of Part 2 is to describe the evolution of new, proven technology which eliminates these deficiencies and provides precise and practical alternatives. These promote the use of realistic geological and mining shapes and eliminate altogether the rectangular approximations of traditional methods. Limitations of the Traditional MethodsThe limitations of the traditional modelling method s (viz. simple block modelling, gridded modelling and their more recent variations) were discussed in detail in Part I . These methods are all based on the use of rectangular discretization to represent the boundaries and volumes of ore deposits and mining excavations. As a result they are unsuited to the representation of nonrectangular geological complexities such as folding, faulting and irregular surfaces . They are equally unsuited to the representation of realistic excavation limits, particularly in the case of underground mining.Recently these methods, with limited variations in technique, have been applied to increasingly more complex geological and mining situations. The resulting potentials for error and conflict within the modelling pro cess were demon strated in Part I . The effects can be summarized as follows:• volume and boundary approximations introduced by therepresentation of irregular three-dimensional boundaries andvolumes by rectangular modelling elements ; • geostatistical errors and conflicts caused by neglect of the relationships between grade estimates and the geometric/ spatial aspects of irregular volumes and associated observations (samples), including an inability to produce precise estimates with meaningful confidence limits;• a compounding of these effects by using rectangular element sizes other than the geostatistical optimum, and by using differentelement sizes within a model; and• general inefficiencies introduced throughout the modelling pro cess by the requirement to represent geology, grade distribution and excavation limits with a singular modelling method and model."

Jan 1, 1991

By B. K. Mishra, Subrat Kumar Padhy, B. C. Tripathy, I. N. Bhattacharya

Manganese is a difficult metal to electrodeposit due to its high electronegativity and continues to possess unique process challenges. Manganese deposits of high quality are electrodeposited on 316 grade stainless steel from sulphate solutions in the presence of organic additives such as tetra ethyl ammonium bromide (TEABr), tetra propyl ammonium bromide (TPABr), and tetra butyl ammonium bromide (TBABr). The concentrations of these additives were examined over a relatively broad range to evaluate their effect on current efficiency, specific energy consumption and deposit morphology of the electrodeposited manganese metal. A maximum current efficiency of 68% was achieved in the presence of TEABr in the bath. X- ray diffraction studies revealed that (330) (411) planes were the most preferred planes of crystal growth during manganese electrowinning at a current density of 500 A/m2 resembling alpha-manganese irrespective of the nature of additive. Scanning electron micrographs showed smooth and uniform deposit morphologies when manganese was electrodeposited in the presence of TEABr.

Jan 1, 2014