Search Documents

By F. M. Jardine

I1944 the cry was for higher production more tons, more metal. New plants were built, capacity of old plants was increased and millmen all over the country were treating tonnages far above normal, sacrificing recoveries to vet that extra metal from extra tons. The list of "critical minerals," at first long, has been scratched until there remains, not a list, but only an item or two. Stocks of all metals and minerals, with possibly one or two exceptions, are now entirely adequate and numerous plants have curtailed or suspended operation.

Jan 1, 1945

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By Kenyon E. Richard, James H. Courtright

SILVER Bell is situated 35 airline miles northwest of Tucson, Ariz., in a small, rugged range rising above the extensive alluvial plains of this desert region. Its geographical relation to other porphyry copper deposits of the Southwest is shown on the inset map in the lower left corner of Fig. 1. The climate is semi-arid. Altitudes range within 2000 and 4000 ft. Opening of the Boot mine, later known as the Mammoth, in 1865 was the first event of note in the district&apos;s history. Oxidized copper ores containing minor silver-lead values were mined from replacement deposits in garnetized limestone and treated in local smelters. Copper production had approached 45 million pounds by 1909 when the disseminated copper possibilities in igneous rocks were recognized. Extensive churn drill exploration carried out during the next three years resulted in partial de- lineation of two copper sulphide deposits, the Oxide and El Tiro. Although the then submarginal tenor discouraged exploitation of these disseminated deposits, selective mining of orebodies in the sedimentary rocks continued intermittently until 1930, providing a production total of about 100 million pounds of copper.

Jan 11, 1954

By J. Visman

FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, in- formation that ultimately can be secured only from actual tests made in the laboratory or in the washery.

Jan 10, 1954

By J. W. JESSUH

TO certain people the name of Northern Rhodesia brings only a vague recollection of a distant country somewhere in Africa; to others, it means a big game territory and the opportunity for excellent shooting; to some, a land of sunshine and peace; but to mining men the name signifies the land where the latest discoveries of copper ore are astonishing the mining world and bid fair, in a few years, to make Northern Rhodesia one of the largest copper- producing countries. There is a fascination about this part of the globe that is somewhat similar to southern California, and at the same time there is that feeling of mystery peculiar to a tropical climate. Perhaps it is the isolation, the fear of wild animals, or the influence of an undefinable something which cannot be expressed.

Jan 1, 1931

By Galen H. Clevenger

THE real and permanent advances which take place in any industry are for the most part slow evolutions which frequently develop and grow almost imperceptibly from clay to clay. A meritorious idea may and generally does require long and patient development and commercial application under a variety of conditions and in a number of localities before it emerges as standard and generally accepted practice. There must be not only technical perfection but also economic advantage. Thus a cross-section taken at any particular time of an industry may reveal little that is distinctly new and yet there may have been considerable progress. During the past year there has been little that is new in milling and yet there has been real progress; some problems have been solved and some of what we may term the newer developments have become more firmly, established.

Jan 1, 1930

By A. M. Gaudin

CHANGES in industrial practice, in plant design, and in research methods which are so clearly to be seen on every hand, have affected the mineral industry as well as others. In particular, ore dressing has passed through a revolution in practice brought about by the introduction of flotation and other quasi-chemical methods, until it has ceased to be solely the mechanical preparation of ores. In fact, the term "ore dressing" itself is obsolescent, and "mineral dressing" has been growing in popularity. This assures adequate recognition of the fact that mineral substances other than ores, e.g. coals, clays, and cement rock, are treated by the same general methods. As a result of these industrial changes it was felt that a complete rearrangement of the curriculum and laboratories at the Massachusetts Institute of Technology would be ad-vantageous. Such a rearrangement would allow instruction and research to proceed in wider accord with industrial evolution and the needs of our times.

Jan 1, 1942

By Donald W. Gentry, John F. Abel

This paper presents some of the results of a rock mechanics instrumentation program designed for, and implemented at. longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam, and immediately below the coal seam. Longwall test panel 4N had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft), [Fig. 1]. The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) although it ranges from 73-134 m (240-440 ft). Roof support at the face was provided by 116 Hemscheidt 320 HSL shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1979

By R. W. Brauchli

During the last few years the compila-tion of formation logs from rotary well cuttings has become common practice among petroleum geologists. This meth-od has undoubtedly furnished a great amount of information valuable for both scientific and commercial purposes. How-ever, in spite of its great usefulness it has certain drawbacks, principally in the contamination of cuttings by cavings. In extreme cases this contamination can reach such proportions that it is next to impossible to draw conclusions with any degree of certainty as to the nature of the formations penetrated by the drill. This difficulty was frequently encoun-tered during the development of the Okla-homa City Field. In many cases where Wilcox sand-the most prolific sand of this field-was drilled, the samples con-sisted almost entirely of shale cavings with only traces of sand. In order to obtain more reliable knowl-edge of the formations encountered while drilling it is therefore necessary to resort to more coring, and above all to improve our present methods of coring. With this in mind a study has been made of the results of coring in the Oklahoma City Field, and the present article is mainly confined to a statistical analysis of the relation between recovery, diameter of cores and drill pipe, length of cores and a few other factors. Most of the coring in the Oklahoma City Field was done during the early part of, the development. A total of around 18,000 feet or 0.3 per cent of the total footage drilled before February, 1932, has been cored, and about 80 per bent of the cores were taken in the Simpson formation at a depth below 6,000 feet.

Jan 1, 1933

By C. L. Dake

Iron is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and. the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.&apos; Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil,4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble and partly insoluble.5 Their iron salts readily change from the ferrous to the ferric form, and their solubility is greatly modified by the presence of ammonia.

Jan 1, 1916

By PAUL H. SHAEFF

THIS paper is presented with the idea of discussing only the basic open-hearth charge. The importance of the charging operation in producing steel is more clearly understood by dividing the principal components into four groups and discussing each separately, thereby becoming acquainted with what constitutes a charge. The significance of these components in the charge itself will then be taken up. Classification of the charge components is as follows: steel scrap; pig iron ; limestone ; refractories and coke. Steel Scarp The first component, steel scrap, according to size, analysis and cleanliness, may be classified as heavy, medium and light. Heavy melting scrap includes crop ends such as are produced in blooming ingots or the heavy crops from bar mills abovely in. in diameter; railroad scrap, which comprises rails, side-plates, car-frames, draw- bars, etc.; and such automobile forgings as axles, crank- shafts, gears, etc. This class of scrap should give a four-box charging-car (box dimension 24 by 18 by 72 in.) an average load of 10,000 to 20,000 lb.

Jan 1, 1926

By AIME AIME

T HE Executive Board of the American Engineering Council held its fourth meeting at St. Louis on the first anniversary of the organizing conference which met in Washington on June 3,1920. Representatives of a number of the leading engineering organizations in the vicinity of St. Louis were present by invitation. The members of the Executive Board were guests of the Associated Engineering Societies of St. Louis. They were given a delightful ride about the city and were entertained at the Glen Echo Country Club at dinner. The special committee that had been appointed to draft resolutions to Mr. Hoover submitted the following, which were adopted : WHEREAS, our President, Herbert Hoover, has been appointed Secretary of Commerce in the Cabinet of the President of the United States, and WHEREAS, in consequence of his acceptance of this high public office, he has deemed it necessary to tender his resignation as President of The Federated American Engineering Societies.

Jan 1, 1921

By Gene D. Clayton, Robert R. Dimock

A time-consuming and expensive preshearing program to minimize the adverse effects of blasting on slope stability at Kennecott Copper Corp.&apos;s Ruth Pit in east-central Nevada has been eliminated in favor of down-the-hole, nonelectric delayed blasting which can produce a smooth wall effect and improve blast fragmentation. The new blasting approach resulted from a Kennecott engineering investigation aimed at improving the stability of the extremely variable rock conditions found throughout the pit by reducing the vibrational energy imparted to the walls with conventional bench blasts.

Jan 4, 1977

By Arthur F. Wendt

Within the last few years the production of iron, and of the metals generally, by a given furnace-plant, has been largely increased, in many instances trebled. Iron-furnaces exceeding one hundred tons&apos; capacity per diem are now the rule in new constructions. Copper and lead-furnaces smelting from 60 to 100 tons of ore per day are common. With this greatly augmented product, the life of furnace-linings has been diminished, and recourse has been had to various cooling devices for prolonging the life of such liuings. The object of this paper is to call the attention of the profession to an arrangement recently patented by the writer. The common course of projecting water against the exterior of the brickwork of a furnace has been in a large measure abandoned by our most progressive managers. All have recognized the danger of this proceeding, especially when applied to the crucible of a furnace below the line of the tuyeres. Cast-iron water-jackets, with wroughtiron pipes for circulating the cooling-water, have replaced the cruder methods. In iron-smelting the use of such jackets has been confined to the crucible and the space around the tuyeres; and it has been the custom to support the jackets on the brickwork of the furnace. But the erosion of the brickwork below tuyere-jackets allows them to sag, and often displaces the alignment of the tuyeres and leads to other annoyances. The principle of construction adopted by the writer to remedy this and other evils, is to use a thin fire-brick lining (not over nine inches) from the tuyeres up to the bosh, to back this lining with wrought-iron or steel water-jackets, hung from the mantel-ring, and thus to carry the whole weight of the furnace and its filling upon the supporting pillars. The crucible proper is lined with three or four thicknesses of fire-brick on the sides, and not less than forty-eight inches in the bottom. It is supported on independent pillars, and is practically an independent structure. It could even be placed on wheels and made removable, were there any adequate advantage to be gained by such an arrangement.

Jan 1, 1885

By W. N. Lacey, R. H. Olds, B. H. Sage

The volumetric behavior of five mixtures of black oil and natural gas and of two mixtures of condensate and natural gas from a field in the San Joaquin Valley was experimentally established. This work was carried out at roo°, I9o° and 250°F in the pressure interval between 400 and 5000 psi. The viscosity of the liquid phase of four mixtures of black oil and natural gas was experimentally measured in the above-indicated temperature and pressure intervals. The effect of methane upon the precipitation of bitumen from the black oil was studied at 230°F. Introduction The solution of a number of the economical and technological problems which arise in connection with petroleum production is dependent upon the availability of the necessary quantitative information covering the materials involved. This requires data concerning physical properties of naturally occurring hydrocarbon mixtures at the pressures and temperatures characteristic of underground petroleum reservoirs. The experimental determination of the desired data for each situation encountered is relatively time-consuming. However, it is considered to yield results sufficiently more reliable than those obtained from correlations to justify the effort. For these reasons there was undertaken a laboratory investigation of the viscosity of the liquid phase and the volu- metric and phase behavior of mixtures of oil and gas samples obtained from wells in a field located in the San Joaquin Valley. Terminology The nomenclature of petroleum engineering is not at present entirely standardized. Many commonly used technical terms are not everywhere given the same meanings. For the purposes of this paper the following definitions will be adopted: Black oil refers to the dark-colored, hydrocarbon liquid obtained when the producing horizon of the well lies partly in the condensed hydrocarbon phase of the reservoir. Condensate is the term applied to the relatively volatile, pale yellow or amber-colored hydrocarbon liquid that is often obtained from the surface separator system when the producing horizon of the well lies in the gas cap of the reservoir. The gas obtained from the surface separator system is called natural gas regardless of whether the well is producing black oil or condensate. As might be expected from the multi-component character of naturally occurring hydrocarbon materials, the compositions of black oil, condensate and natural gas are subject to considerable variation depending upon the temperatures and pressures prevailing in the surface separator system as well as upon the overall composition of the material produced from the reservoir. In order to obtain samples capable of reproducing the total hydrocarbon material produced by the well, all oil and gas mixtures used in this investigation were com-

Jan 1, 1949

By A. C. Fieldner

DURING 1939, 286 by-product coke ovens were completed and put into operation. These included 140 Witputte ovens for the Carnegie-Illinois Steel Corp., at Gary, Ind.; 61 Koppers-Becker ovens for the Ford Motor Co., at River Rouge, Mich.; 65 Semet-Sotvay ovens for the Great Lakes Steel Corp., Zug Island, River Rouge, Mich.; and 20 Curran-Knowtes ovens for the Midwest-Radiant Corp. plant at Mitlstadt, Ill. The Millstadt plant is unique in carbonizing a washed coat containing 3.50 per cent sulphur. The gas contains approximately 2500 grains sulphur per 100 cu. ft.; this is successfully removed with sodium carbonate solution by the Seaboard liquid purification process. The coke is intended primarily for use as a smokeless domestic fuel in the city of St. Louis.

Jan 1, 1941

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

By Robert E. Tally

A recorded in the account of the Annual Meeting, on another page, the report of the tellers showed that all men nominated by the committee, which included Messrs. Wilber Judson, E. DeGolyer, W. A. Weldin, J. A. Norden, J. D. MacKenzie, Wilfred Sykes and S. Skowronski, were duly elected to the offices for which they were nominated. Robert Tally, who was elected to the presidency for 1931-2, is well known to all our members not only because he has served on the Board of Directors since 1928, but through a brief outline of his great achieve¬ments in his chosen profession pub¬lished in our issue of December last. The vice-presidents, Howard N. Eavenson and H. A. Guess, are also well known to our members. Mr. Eavenson has not only been chairman of the Coal Division since its organization, but was also a Director during 1917, 1918 and 1919., Mr. Guess was Director in 1926, was elected a vice-president by the Board last year to fill the vacancy created by the election of Mr. Bassett to the presidency, and is now elected to the usual three-year term.

Jan 1, 1931

By W. S. Ayres

I. INTRODUCTION. THIS cavern was discovered Oct. 22, 1904, by Mr. Charles H. Deutschman, in company with whom I made, May 29 to June 3, 1905, at the request of Mr. Howard Douglas, Superintendent of the Canadian National Parks, the first exploration of it for the Canadian government. The results were stated in a paper, orally presented, with lantern-views from my photographs, at the British Columbia Meeting of the Institute, Victoria,, B. C., July 5, 1905.* The present paper embodies also the results of a second examination, made Oct. 25 to 29, 1905. The accompanying map, Fig. 1, will serve as a guide to the following description. II. LOCATION. The cavern is situated at snow-line, at the head-waters of Cougar creek, on the west slopes of the Selkirks, about 2 miles north from Ross Peak water-tank, and 5.5 miles west from Glacier House, on the main line of the Canadian Pacific Railway. It was then reached by an arduous climb from the water-tank, up the ravine of Cougar creek, for 8,000 ft. (2,000 ft. of altitude) over rock- and snow-slides, and through a thick tangle of alders. But an easy and very picturesque trail has, during the past summer, been opened by the government from Glacier House. Figs. 2, 3 and 4 represent views, not heretofore published, of the grand scenery of this region, so rapidly becoming the-object of attraction to thousands of tourists from all parts of the world. These views, as well as those shown in. Figs. 5, 6, 7, 8

Jan 1, 1907

By H. Stigzelius

FINLAND&apos;S recent mining history is both dramatic and pitiful in its shifting fortunes, dominated as it has been, by the country&apos;s proximity to the border zone of opposing dictatorships and social traditions; Fascism to the south, Communism to the east, and Democracy to the west. After 108 years under Russia&apos;s more or less harsh rule, Finland gained its democratic independence during the 1917 revolutionary strife in Russia with the official help of Germany and spontaneous help of other neighbors. The young nation was attacked by Russia in 1939 and again in 1941. It is common knowledge how the Finns fought with everything they had and everything they could get against their overwhelming adversary, and how by force of circumstances they landed in the Axis camp in 1941. Finland has never been known as a mining country in the same way as near-by Sweden, whose abundant iron and copper smelters during long periods so greatly contributed to the nation&apos;s welfare. Its largely barren, Archaean-granite geology long seemed forbidding. Some mining was done, to be sure; copper and tin at Pitkaranta near the Russian border, and lead and copper at Orijarvi. But towards the end of the last century the absence of a single producing mine cast a pessimistic shadow of truth over the Finnish poet Runeberg&apos;s words, that

Jan 1, 1946