Search Documents

By D. E. Munson, H. J. Sutherland

Empirical methods for describing the shape of the subsidence trough over coal mines in Europe are tested against field measurements of subsidence over longwall panels in the United States. The graphical methods developed by the National Coal Board in the United Kingdom do not correlate well with the U.S. measurements; however, the profile functions typically used on the Continent give quite acceptable fits to the data. In the case of two longwall panels mined at Old Ben No. 24 in Illinois, a trigonometric profile function appears the best choice; in the case of two longwall panels mined at York Canyon in New Mexico, an error integral function is somewhat superior. Analyses of subsidence development curves show that rate effects occur. A comparison of fitting parameters establish influence functions as an important methodology for future analysis. In conjunction with the evaluation of empirical methods, an analytic model based on material failure and bulking was developed. A key element of the model is the void-volume distribution function which establishes a mechanism for transfer of significant amounts of the mined volume to the surface. Preliminary calculations demonstrate the features of the model and illustrate close correlation to physical observations in the field. Moreover, centrifuge models simulating the subsidence process have been used successfully to demonstrate the dominant or key failure modes necessary to the analytic model. General features of the centrifuge simulations and model calculations correlate well.

Jan 1, 1982

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

By R. A. Jankowski, J. J. McClelland

Laboratory tests were conducted by the U.S. Bureau of Mines to determine the respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Exhausting face ventilation was varied from 3,000 to 9,000 cfm (1.42 to 4.25 m3/sec). Spray-water-flow was varied from 15 to 35 gpm (0.057 to 0.132 m3/min), while nozzle operating pressure was varied from 80 to 200 psi (5.62 to 14.06 kg/cm2). Results from gravimetric dust samples indicated that airflow had the greatest individual impact on reducing dust levels, with return and operator concentrations reduced by as much as 57% and 99%, respectively. Interactions between dust control parameters were found to be significant. Often, these interactions defined a level of application for a control parameter where further increases in that parameter failed to produce additional reductions in dust concentrations. In several cases, increases in a control parameter resulted in higher dust levels at the operator's location. These higher dust levels were attributed to additional rollback and/or airflow turbulence. Regression modeling indicated that increases in airflow to 8,400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.84 kg/cm2) typically were beneficial at the operator and return sampling locations.

Jan 1, 1991

By Steven H. Brown

Ore bodies which were once uneconomical to mine by conventional methods such as tunneling or open pits, have become attractive due to the development of nonconventional techniques, involving considerably less capital expenditure. Technologies such as uranium solution mining or in-situ leaching, have enabled commercial scale mining and milling of relatively small ore pockets of lower grade, and may make a significant contribution to overall U.S. uranium supplies during the next 20 years. Commercial size solution mining production facilities have operated since late 1975. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a processing plant. Processing involves ion exchange, precipitation, calcining, and packaging operations. This paper presents an overview of the solution mining process and the health physics monitoring programs developed over the last four years at several production facilities as a result of the radiological character of these processes. Although many radiological aspects of the process are similar to that of conventional mills, conventional-type tailings as such are not generated. Some special monitoring considerations are presented which are required due to the manner in which radon gas is evolved in the process and the unique aspects of controlling solution flow patterns underground. An overview of the major aspects of the health physics compliance and monitoring programs that have been developed are discussed.

Jan 1, 1981

By J. W. Langhans, B. D. Blake

The U. S. Bureau of Mines has been investigating the application of thiosulfate to recover gold directly from low grade refractory carbonaceous ores for the past four years. Statistical experimental methods were used to determine the effects of various leaching parameters on both gold extraction and thiosulfate consumption. Seven variables were investigated, including thiosulfate, copper, ammonia, sulfite, and sulfate concentrations, leaching time, and leaching atmosphere. This information was used in face-centered cubic (FCC) surface response experiments to define the optimum leaching conditions for a low grade ore. Two models were generated from the data to predict gold extraction and thiosulfate consumption as a function of the leaching parameters. The models predicted a gold extraction of 67 pct and reagent consumption of 2 kg [S2032/mt ore at 0.25 M S2032-, 0.0014 M Cu2+, 0.27 M NH,OH, 0.00625 M SO;-,] and leaching for 16 h. Actual tests resulted in 62 pct gold extraction with 0.93 kg S2032- consumed/mt ore. Subsequent column leaching tests have further demonstrated the viability of applying this technology to recover gold from carbonaceous ores without first pretreating the material. Gold extractions in the column tests ranged from 69 to 78 pct with thiosulfate consumption ranging from 0.4 to 5.4 kg/mt ore. These results compare to <5 pct gold extraction using standard cyanide leaching conditions.

Jan 1, 1996

By S. Grogan

Next year marks the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). As the U.S. coal industry scrambles to cope with serious economic difficulties, it is appropriate to examine some other difficulties that have their origin in certain provisions of that ten year old law, and that bear directly on the economic viability of surface coal mining in the west. This paper focuses briefly on three technical issues in the reclamation of surface coal mines in arid regions, and suggests that innovation can resolve these issues. The coal industry operates within a narrow legal context, defined in 1977. In enacting SMCRA, Congress listed among the purposes of the Act ?... to...strike a balance between protection of the environment, agricultural productivity and the Nation&apos;s need for coal as an essential source of energy." I maintain that such a balance has never been struck, particularly with regard to the reclamation of mines in the west. One reason is that when SMCRA was enacted its supporters were aware of uncertainties about the potential for successful reclamation of western surface mines. Over the intervening years, as a recent Congressional study report (OTA, 1986) points out, "...the risks these uncertainties may pose to the long term success of western reclamation have been reduced significantly." Unfortunately, SMCRA&apos;s enforcement agency, the Office of Surface Mining (OSM) has not yet recognized this fact, and the western coal industry is paying the price.

Jan 1, 1986

By Haydn H. Murray

Since the advent of machine coated paper in the mid 1930&apos;s, the kaolin industry has had a remarkable growth, In 1935 the domestic production of kaolin was 500, 000 tons and in 1970 the estimated production was in excess of 3. 5 million tons. The process industries which use kaolin most extensively are paper, rubber, paint, ceramics, plastics, catalyst manufacturers, ink, and pharmaceutical. The paper industry is by far the largest consumer of kaolin using approximately 70 per cent of the total tonnage mined and beneficiated. Up until 1970 the major kaolin producers were able to expand rapidly enough to supply the demand but for the first time in thirty years the demand is expected to be in excess of mining and beneficiation capacity through at least 1975. The major reason for this is the expansion of coated paper production in Europe and Japan. Two areas supply the lion&apos;s share of kaolin for the world markets. These are the Cornwall area in extreme southwestern England and a limited area of Georgia and South Carolina in the southeastern U. S. The English kaolins are primary - (found in decomposed granite) whereas the Georgia-South Carolina kaolins are secondary - (found in lenticular, continuous beds in the Tuscaloosa formation of Cretaceous age. ) The English kaolins are mined by hydraulic methods whereas the Georgia-South Carolina kaolins are mined by dragline or shovel and benefidated by using a wet process for the majority of the production and/or a dry

Jan 1, 1971

By John P. Albers

During the 1950&apos;s and 1960&apos;s a program of geologic mapping of counties has been underway in Nevada by geologists of the U. S. Geological Survey and the Nevada Bureau of Mines. The aping has been done principally at reconnaissance scales, with more detailed work in local areas. Geologic maps are either published or open-filed for about a dozen counties at scales of 1:200,000 or 1:250,000. One by-product of the geologic mapping has been the recognition of about 80 Tertiary volcanic centers from which large or very large volumes of volcanic material ranging from rhyolitic to andesitic in composition have been erupted. For purposes of this discussion these are regarded as the major centers; the tally does not include hundreds and perhaps thousands of small rhyolitic domes and plugs and basaltic vents. About 15 to 20 of the 80 major centers are believed to be calderas ranging in diameter from 3 to 25 miles. Some have been described in the literature by geologists of the Nevada Test Site and others. However, the vast majority of the 80 centers have not been described in print, and we are indebted to our colleagues for locating them for us in many of the counties. Briefly, we would like to express our appreciation to the following people all members of the USGS unless identified otherwise: Robert Coast, who has identified the centers in Elko County; Ron Willden, Robert Yates, and

Jan 1, 1968

By G. F. Friel, G. S. Morrow, J. C. Edwards

An experimental program in the U.S. Bureau of Mines&apos; Safety Research Coal Mine evaluated the effects of dead end crosscuts on the transport time of CO along a mine entry. The presence of carbon monoxide is a characteristic of a fire in its incipient stage, and is significant in the determination of a fire location in a mine from the analysis of arrival times of pre-set concentrations at CO monitors. In this investigation two entries, with a total of ten crosscuts, connected by a room were instrumented with CO sensors as part of a real-time monitoring and data acquisition system. Controlled release of 1% CO was monitored as the contaminant traveled the entries for several different configurations of CO sensors and exhaust fan settings. In addition to the normal longitudinal dispersion of CO due to turbulent mixing at the front of the CO wave, the induced rotation of air established within a crosscut by the entry flow diluted the CO concentration through entrainment. It was determined experimentally for the entry and crosscut configuration considered that the transport time for a specified CO concentration was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and total crosscut volume. The proper interpretation of the measured transport time of a specified contaminant concentration between sensors is important for mine safety in the isolation of a fire and plans for miner evacuation.

Jan 1, 1993

By Prof. Dr. T. R. Boulos

The Egyptian marine phosphorite of Sebaiya West, the Nile Valley, consisting of both non-oxidized hard siliceous and oxidized leached friable ore types, is subjected to a roughing-cleaning silica flotation circuit for production of wet-process phosphoric acid concentrate. Operating at its maximum capacity of 268 t/hr, the following were the main problems encountered during the early stages of running the plant: 1. The tremendous amount of slimes generated by scrubbing the crushed ore causing turbidity in the plant thickener after a short time of operation, regardless of the added flocculant. 2. Rod mill choking leading to inefficient performance of all other equipment and poor flotation results. 3. The drastic increase in imported oleic acid price. Pulp density and slurry flowrate measurements at different points of the plant as well as ore microscopy, size distribution analysis, chemical analysis and x-ray diffraction analysis of representative ore samples coupled with Work Index measurements of feed samples showed that the wide variation in the ore&apos;s hardness was responsible for such problems. Application of the locally produced non-edible rice bran oil as a substitute to imported oleic acid in flotation resulted in total saving of U.S.$2 million in 1990. The total unsaturated fatty acid content of the oil is high, ranging from 75.2 to 81.5 mole % of which the C18-unsaturated fatty acid content ranges from 72 to 79 mole %.

Jan 1, 1993

By Joel D. Hammond

Lightweight concretes date back to before the Roman Empire. The earlier concretes were made by combining a burnt lime for cementious material with pumice or volcanic rock for aggregate. Although structural value was limited due to its primitive nature, many structures were able to withstand the test of time. The rotary kiln expanded shale industry had a slow start that began around 1908. The industry was founded by Stephen J. Hayde of Kansas city, Missouri. Mr. Hayde noticed that the bloating effects of some aggregates were undesirable by the brick industry. Material of this type was considered waste and avoided in brick production, but he realized it had all the qualities and basic requirements for a concrete aggregate that would reduce weight and still retain structural value. It came into national attention by use in ocean-going vessels through a shipbuilding program undertaken by the united states Fleet Corporation. This research was brought about by the need to find a suitable material to replace high-grade plate steel due to a shortage created by World War I. The need prompted the government to supply the reserves that Stephen Hayde desired to continue and complete research into producing a uniform lightweight aggregate. His results pointed to the rotary kiln method for which he was granted a patent in 1918. One of the most famous and largest concrete ships built through this program was the U.S.S. Selma. Although the Selma

Jan 1, 1977

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a room-and-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the U.S National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90 percent. But the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining-industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing over-sprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99 percent and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber. 

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof&apos; control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to evaluate the effect of ventilation on the performance of automatic sprinkler systems in extinguishing wood crib fires. Experiments were conducted at airflows of 0, 0.76, 1.5, 2.5, and 4.1 m/s. Two experiments were conducted at each airflow, using 74° C fast response pendent sprinklers in one experiment and 74° C fast response horizontal sidewall sprinklers in the other experiment. In the experiments at airflows of 0 and 0.76 m/s, sprinklers were located directly above the fire and 2.4 m upstream and downstream of the fire. The sprinkler directly above the fire was the only sprinkler to operate with no discernible difference in the suppression capability of the pendent and horizontal sidewall sprinklers. In the experiments at airflows of 1.5 and 2.5 m/s, sprinklers were located directly above the fire and 2.4 and 4.8 m downstream of the fire. The sprinkler located 2.4 m downstream was the only sprinkler to operate with the horizontal sidewall sprinkler being more effective in extinguishing the wood crib fire. The average response times of the sprinklers at airflows of 0.76, 1.5, and 2.5 m/s were 3-1/2 times the average response time of the sprinklers at 0 m/s. The results of this study will help enhance the safety of the nation&apos;s miners.

Jan 1, 1993

By J. F. T. Agapito, C. E. Brechtel, C. J. Gilbert, T. R. Kelly, R. C. Karlson

A multi-lift benching cut-and-fill mining method was adopted at Asamera Minerals (U. S.), Inc.&apos;s Cannon Mine to balance the goals of high productivity and near 100 percent recovery with the need to minimize subsidence. High strength backfill was required to provide effective long-term overburden support and safe working conditions during the pillar recovery operations. Operational designs were evaluated using numerical modeling to predict global mine stability and backfill strength requirements. These models incorporated sequential mining of primary stopes, backfilling of primary stopes and recovery of pillars, and have been transferred to the mine operations group for use in evaluating different production sequences. The modeling has provided a better understanding of the structural response of the mine to excavation of the primary stopes and removal of the pillars. Predictions about the transfer of overburden weight to the abutments, pillars and cemented fill pillars have provided a criterion to evaluate mining plans and production sequence. Comparison of these predictions with actual mine structural performance has developed confidence in the design of the mining method and in the geomechanical design methods being employed. Primary mining of the B-North zone is nearly complete, and the stopes have been generally stable, as projected in the original design. Some exceptions have occurred where locally stope pillars have failed due to the presence of adversely oriented sheared beds. Recovery of the pillars between the

Jan 1, 1987

By John J. Peregoy, James E. Downes

INTRODUCTION The U.S. Department of Energy&apos;s Waste Isolation Pilot Plant (WIPP) is being constructed to provide permanent storage of radioactive TRU waste materials emanating from military weapons production. These wastes are contaminated with radioactive elements heavier than uranium, thus the name trans-(or beyond) uranic (Uranium wastes). The WIPP site, which is located 26 miles east of Carlsbad, New Mexico, was chosen thru a selection process after the National Academy of Sciences recommended salt deposits as a promising host strata for the storage of radioactive wastes. Throughout the United States numerous DOE facilities have produced and stored defense-generated TRU wastes. Once WIPP becomes operational in the fall of 1989, all sites may ship directly to this repository. A companion project has developed special shipping containers (TRUPACT) for safe transport of materials to WIPP. The WIPP facility is currently composed of surface buildings, three shafts, and underground storage and experimental rooms and tunnels. Frontier-Kemper Constructors, Inc. (FKCI) has nearly completed the construction of the fourth shaft, an intake shaft, to provide additional ventilation to the underground workings. PLANNED SHAFT EXCAVATION METHOD Full-face raise boring ( upreaming ) was the allowable method selected by Frontier-Kemper Constructors for the excavation of the shaft. After arrival of an oil-field type rotary drill rig in December 1987, a 9 inch diameter pilot hole was drilled from the surface to the mine level, a depth of approximately 2145 feet.

Jan 1, 1989

By Eugene L. Foster, Gilbert L. Butler

The successful demonstration of a precast segmented concrete liner in the Lexington Market Section of the Baltimore Regional Rapid Transit System (BRRTS) is an important step forward in our continuing efforts to control tunneling costs in the USA. In addition to its contribution to specific savings in future tunnels, this demonstration project has taught other lessons about the U.S. tunneling industry and about the process of "mainlining" new and improved technology into that industry. This paper will present an overview of the Lexington Market Demonstration Project from its beginnings to the present time. In addition, it will discuss other implications which have an important bearing on the extent to which tunnels will be used in future transportation systems in the USA. THE HISTORY Precast segmented concrete tunnel liners are not new. An unbolted version was reportedly used in New York City in the 1930&apos;s. The modern bolted configuration has been in use in foreign countries for more than 15 years. Indeed, consideration of the use of precast bolted segments below the water table in the USA dates back to the BART system in San Francisco in the 1960&apos;s. At that time, they were evaluated and it was concluded that the state of the art would not allow segments to be precast to the required tolerances. A secondary grinding operation would be required if water-tightness was to be assured, making them economically non-competitive with steel. Based

Jan 1, 1981

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By Robert S. Setren, Jeffrey L. Ambs

The disposable diesel exhaust filter (DDEF) system developed by the U.S. Bureau of Mines and Industry cooperators for heavy-duty permissible, diesel-powered haulage vehicles, effectively reduces in-mine diesel particulate matter concentrations up to 95%. However, there are concerns about the hazards that exist when the filter is used in situations for which it was not designed. This work investigates the exhaust gas temperature limits to which the filter elements can be exposed without posing a safety or health hazard, such as 6re or off-gassing toxic compounds. A filter approved by the Mine Safety and Health administration and after-market filters were evaluated under varying engine exhaust conditions to determine if after-market filters pose an unacceptable hazard when used in a DDEF system. Filters were laboratory tested at engine exhaust temperatures ranging from 77°C to 290°C. Of the seven filter types tested, six appeared suitable for use on water scrubber-based cooling systems and two appeared suitable for use on dry heat exchanger type exhaust cooling systems with exhaust temperatures up to 150°C. Any filter elements used as exhaust filters on permissible diesel machines must be approved by MSHA for that application. Mine operators who wish to use an after-market filter element should request an MSHA field modification. MSHA will work with the mine and filter manufacturer to ensure its use in this exhaust system application does not pose a health or safety hazard.

Jan 1, 1995