Search Documents

By S. C. Sun

The grinding of coals for coal preparation has been studied extensively by previous investigators, but no similar work has been done on coal lithotypes (l-4). However, the different natural breakage characteristics of coal lithotypes have been recognized and utilized by the coal industry (5,6) to develop the Longway Burstlein process (7) for the concentration of macerals(8). The specific objective of this research was to determine the relative grindability of lithotypes, obtained from both anthracite and bituminous coals. An attempt was made to relate the findings, wherever possible, to the chemical and physical properties of the tested lithotypes. Another aspect of this research was to ascertain the size distribution and grindability of lithotypes ground at a various number of revolutions in a Hardgrove mill.

Jan 1, 1970

By Brian Fulcher, John Eastlund, J. B. Copeland

Following the completion of the 7,600 m primary access tunnel by Kiewit/Parsons Brinckerhoff (K/PB) in April 1997, an exploratory East-West Cross Drift Tunnel was constructed at the Yucca Mountain Project over the proposed future repository block for high level nuclear wastes. The 2,681 m (8,796 LF) East-West Cross Drift Tunnel was excavated through volcanic tuffs having zones of incompetent rock using a re-built Robbins 5.000 m (16’-5”) hardrock TBM with a special arrangement of supporting equipment. Details of the unusual site and contract conditions will be discussed as well as with the unique tunnel equipment specified by the Owner. This portion of the Yucca Mountain project required eight months to complete.

Jan 1, 1999

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

The Tolt Pipeline No. 2, West Snoqualmie Valley project, is part of a water supply project linking the Tolt reservoir in East King County to the City of Seattle through a nominal 2.13 m (7-ft) inside diameter conveyance. Receipt of the National, 2002Microtunnel Award provided recognition of the many challenges overcome by this project. Baseline conditions revealed in the Geotechnical Documentation included over-consolidated glacial deposits, landslide and alluvial deposits, artesian water, boulders up to 36-in in diameter, logs, heaving sands, and liquefiable soils beneath the river. Schedule constraints associated with setting the shafts in the floodplain of a salmon bearing river and the fickle performance of the river during those times it was not supposed to flood added to the challenge.

Jan 1, 2003

By Jörg Holzhäuser, Matthew Crow

An 18.5 km (12 mile) long tunnel is being driven by four Earth Pressure Balance Tunnel Boring Machines (EPB-TBMs) of 4.7 m (15.5 ft.) diameter through alluvial sand, gravel, silt and clay above and below the groundwater table in Los Angeles beneath buildings, railroads, freeways and the L.A. River. Continuous automatic data recording of TBM operation and field inspectors' records, accompanied by monitoring of 5,000 surface reference points and 268 borehole extensometers were used to obtain information. The paper explains the reason for selecting the method of EPB-tunneling to ensure stability of the tunnel and meeting of environmental requirements, and presents data collected to monitor and demonstrate the performance of the TBM sin the different ground conditions encountered.

Jan 1, 2003

By Thomas M. Lynberg

WIDCO is a surface coal mine located near Centralia, Washington. The WIDCO preparation plant processes over 7 million tons of run- of-mine coal each year with a product yield averaging 72%. In the jig type preparation plant the fine refuse amounts to approximately 130 dry tons per hour of 28mesh by 0. This fine refuse material is thickened in a 160ft. diameter static thickener with the use of lime as a coagulant and organic polymer as a flocculant. Once thickened the fine refuse, which is predominately bentonitic clays, has been dewatered and disposed of using several different methods. These methods will be discussed and include vacuum disc filters, ponds, solid bowl centrifuges, belt filter presses and experiments with electrokinetic dewatering.

Jan 1, 1981

By Courtney Black, Paul F. Ziemkiewicz, Eberhard Werner, Matthew Daly, Joseph J. Donovan, Jeff Frazier

Injection of alkaline waste-lime slurry was performed at a West Virginia surface coal mine site, to attempt neutralization of acid springs by an alkaline recharge method. Deep trenching (>5 m) using an excavator yielded the most effective injection into the aquifer. Water from two springs, 90 m from the deep trench, showed 70%-80% reduction in acidity in response to injection. Neutralization persisted >170 days after treatment, with pH between 5.1-5.7 and metal acidity from 25-60 mg/L. A minor fraction of lime introduced was consumed. The sustained neutralization is attributed to reaction of acid water with subsurface lime, entrained below the wafer table by macropore infiltration. Characteristics of groundwater transport are critical in determining recharge structure location.

Jan 1, 2000

By Eugene Honeycutt, David Gallagher, R. E. Melley, Nick Madison

Drummond Co. Inc.'s Shoal Creek Mine slope conveyor is the highest lift, highest horsepower, highest tension conveyor system in North America. The system has a capacity of 4950 t/h (5500 tph), a vertical lift of 360 m (1180 ft) and a total connected power of 6000 kw (8000 hp). The mine will include 2 longwall machines and 5 to 7 development sections. Annual raw production will approach 9 million tly (10 million tpy). This paper describes the early investigation of system capacity, haulage system options, and the final selection of a single flight belt conveyor. It will review the basic system de- sign and equipment selected. Also included will be some highlights of the installation of the conveyor system.

Jan 1, 1996

By David J. Dunn

Mill liner design is an important factor in grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, liner life, and liner wear rate At a time when mill avilability is at a premium, production costs are going up, and lead time for mill liner castings is a year or more, the mill liner that grinds best, lasts longest, and costs least is a necessity for economic mill operation. In testing four mill liner profiles for 13' x 12' overflow ball mills, Climax found that an improved design increased mill tonnage by 3 tons per hour while reducing finish grind by 1.7% + 100 mesh, reduced liner wear rate, and almost doubled liner life.

Jan 1, 1976

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The US Bureau of Mines (USBM) and Amax Coal Co. studied surface coal mine overburden blasting near four steel and one PVC pipeline of 15 to 51 cm-diam (6-20 in.-diam), monitoring vibration, strain and pressure. Unlike tests of small blasts simulating construction, these were up to 1 t (2200lbs) per delay in 31-cm (12-in.) blastholes. Worst-case comparisons showed that 12.7 cm/sec (5 in./s) blasting vibrations produced strains about one fourth that of pressurization and 10% to 18% of the ultimate tensile strength. No failures occurred from blasting as close as 15 m (50 ft), which produced vibrations over 60 cm/sec (24 in./s).

Jan 1, 1995

By E. Yuksel

Noted as one of the 20 major economies of the world, Turkey is a semi-arid plateau between the Eurasian and the African continents. With its surface area of 780 thousand sq km, it supports a population of 70 million people. While the mining history of Turkey can be traced back as far as 7 000 B.C., mining currently generates only 2% of Turkey’s gross national product. Turkey has 77 of the 90 principal minerals that are mined world-wide. Currently, some 5 000 mine occurrences including copper, lead, zinc, iron, gold-silver, chromite, sepiolite, mercury, and coal deposits, soda ash, marble, zeolite, feldspar, magnesite deposits, as well as the world’s largest known borate deposits, have been discovered and partially explored.

Jan 1, 2004

By Chris D. Breeds

Northwest Boring, Inc. (NWB) deployed a skinned up AVN 2000AB Microtunnel Boring Machine (MTBM) to install 7.5-foot long, 118-inch outer diameter reinforced concrete pipe (RCP) sections along an alignment between the Fremont (FRS) jacking shaft and the 3rd Avenue (3RS) receiving shaft for the Ship Canal Water Quality SCWQ Project. The alignment includes: a 67-foot long straight section, a 367-foot long curved section excavated along a 650-foot radius curve, followed by a 182-foot long straight section. This paper describes the project including planning and design, manufacturing, equipment installation in the 90-foot-deep FRS jacking shaft, egress through the secants and microtunnel operations required to complete the shaft and install the required casing pipes.

Dec 1, 2022

By J. W. Shuster

Test of trolley-diesel prime power is another step in the search to exploit the unused potential of electric wheel driven haulage trucks. The output of the present engine - a 700 horsepower diesel - is not adequate to exploit fully the 1200 horsepower potential of the two electric wheel drive motors. Power was supplied to a modified 100-ton haulage truck through a double wire trolley system. The vehicle was tested with various payloads on a 7% adverse grade haul road. More significant conclusions developed are: Power - Horsepower to propel the vehicle can he more than doubled to improve truck cycle time. Productivity - Trolley power up adverse grades can improve [producivity] rates from 18 to 36%, dependent upon haul road profile.

Jan 1, 1968

By J. W. Hawkins, K. B. C. Brady, M. W. Smith

The Pennsylvania Department of Environmental Protection (PaDEP) has been issuing surface mining permits since 1984 that authorize remining in areas that will affect preexisting pollutional discharges. These permits require the mine operator to employ best management practices to reduce pollution loading from abandoned mine discharges. A total of 110 completed mining operations with 233 discharges were evaluated to determine the impact to water quality. Overall, acid loading from these discharges was reduced by 7, 200 kg (15, 900 lbs) per day or 61%. Metal loadings were also reduced. For acidity, 49% of discharges improved or were eliminated, 52% showed no significant change and fewer than 1 % got worse. Loading reductions resulted from a combination of reduced concentrations and lower flows.

Jan 1, 2003

By Tetevi B. Wilson

Analysis of the distribution of ore-bodies in space can be useful generally in the estimation of mineral resources or the management of exploration. This study is di¬rected to analysis of the undiscovered potential of well known areas of mining district size, referred to as metallogenic units (MUs). The analysis employs an effort¬ adjusted and truncated probability model for number of occurrences within a subdivision (quadrat) of a MU and Monte Carlo sampling to generate an approximation to the probability distribution for number of occurrences and number of mines within an MU when it is totally explored. Exploration potential for Monitor, Bodie, Au¬rora and Camp Douglas MUs (Walker Lake quadrangle of Nevada and California) are estimated to be 9, 4, 7 and 4 mines, respectively.

Jan 1, 1992

By G. G. O. O. Uwadiale, M. A. Kollere, M. A. U. Nwoke

Birnin Gwari and Alawa graphite deposits were upgraded by flotation. Using 0.5 kg/t kerosene and 0.25 kg/t sodium silicate, flotation concentrates grading 90.7% and 88% Cg with recoveries of 86.2% and 84% were produced from Birnin Gwari and Alawa graphite samples, respectively. The combination of 0.5 kg/t kerosene, 0.2 kg/t pine oil and 0.25 kg/t sodium silicate yielded high-grade graphite (92.3% Cg) with a recovery of 83.9%. Flotation with refined rubber nut oil and kerosene, at a 1:1 ratio, produced a concentrate grade of 86.3% Cg with a recovery of 90.4%. With acid leaching of the flotation concentrate, a high-grade graphite concentrate containing 98% Cg was produced.

Jan 1, 1998

By Bruce A. McKinstry

For many major mining projects the time frame from initial planning to production can be measured in terms of decades. Hecla's Silver Shaft project, which is scheduled to go into production by the end of this year and includes a complete surface facility, shaft with an ultimate depth of 2,348 meters (7,700 feet), complete ore pass and loading pocket system, and 610 meters (2,000 feet) of development drifting and stope preparation, was initially concieved in the Fall of 1979. This duration of a mere four years from conceptual engineering to production is a testimonial to what can be accomplished when a progressive mining company and an innovative contractor work together as a team rather than developing into two warring camps as often happens.

Jan 1, 1983

By Tim Q. Haldane

The ability to efficiently process low grade gold ores has allowed the Gold Fields Mesquite Mine in Imperial County, California to expand from a 2.1 million tonne per year rate in 1986 to its present 7.3 million tonne per year processing rate. Increased tonnage demands led to the 1989 construction and start-up of a dump leach pad to supplement the existing heap leach operation, resulting in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. An overview of current operating practices at Mesquite is presented along with metallurgical and economic comparisons between the crushed and run-of-mine ore heaps.

Jan 1, 1990

By Stanley Lefond

The health of the industrial minerals industry appears to be improving year by year. In fact, preliminary information suggests that only three commodities (asbestos, bromine, and sulfur-other) failed to show a production gain in 1984 over 1983. In 1983, 10 commodities failed to post gains and six remained constant. The total value of industrial mineral production in 1984 was $16.7 billion, up $1.4 billion from 1983. Cement, clays, gypsum, and crushed stone production increased. Since these are used in housing and construction, this suggests these industries are moving out of their recent doldrums. Barite and clay production also improved in 1984. Local US barite production, however, still has a long way to go to attain the 1981 high of 2.6 Mt (2.9 million st). Barite imports remain high. But they are not as high as the 1982 importation of 2 Mt (2.3 million st). Bentonite production in 1984 increased 20% in volume and 25% in value over the previous year. This suggests improvement in the drilling industry and an increase in demand for iron ore pelletizing grades. All in all, the industrial mineral industry is alive and well. And it shows signs of great improvement in the next few years. Many thanks to those industrial mineral technical committee members for their assistance in assembling this industrial minerals review: M. F. Dibble, H. W. Allen, G. H. Gallup, S. G. Ampian, D. W. L. Spry, H. G. Fleshman, and L. J. Czel.

Jan 5, 1985

By William Hodder, Ehsan Alavi, Muhib Hussain

Disc Cutter Wear is influenced by several geological and technical factors and excessive wear can have a major impact on the excavation efficiency of Tunnel Boring Machines (TBM). Disc cutter replacement events cause a disruption to the construction schedule and costs, and should be minimized throughout the project to the extent possible. A well-executed cutterhead inspection and maintenance plan can help mitigate abrupt cutterhead interventions and reduce its effect on project schedule and cost. This paper examines cutterhead inspection and disc cutter replacement events as well as subsequent wear data recorded in the first 7km of the 10.3 km long, 6.3 m diameter Coxwell Sanitary Bypass Tunnel (CBT) project in Toronto, Ontario. The CBT alignment is mainly through Georgian Bay Formation shale.

Dec 1, 2022

By H. Vigil Fernandez, G. Peach

The Musaimeer pump station and outfall project located in Doha Qatar, was designed to collect and manage ground and stormwater and then discharge the treated waters offshore. The project constructed a long outfall tunnel using an EPB TBM with segmental lining, each tunnel ring being 1.35 m in length with an internal diameter of 3.7 m.. The diffuser structure was a 6-arm structure, measuring 294m by 40 m connected to a central manifold in turn connected to the TBM constructed tunnel via a riser shaft drilled from an off-shore barge. This technical paper will discuss the planning, methodology and construction practices employed to connect the TBM tunnel to the diffuser structure 10.2 km offshore.

Jun 13, 2023