Search Documents

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d'Or, Québec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By S. J. Dillingham

One of the primary goals of every blaster is to achieve the optimum blast design. Too much focus on efficient design, however, can cloud certain issues and exposures that must be addressed if the entire project is to be considered .successful.. Due to the known human response to blast effects and inherent dangers present in the use of explosives, the potential for the project being delayed or shutdown, or the blaster and associated company being named as a defendant in a lawsuit, is always a possibility. Therefore, the blast design and associated project bid must incorporate sound safety contingences and procedures that address those .what-if. Scenarios that may arise as a result of vibration, flyrock, public relations, and job-site personal safety.

Jan 1, 2002

By Keith Orgeron, Tibor Rozgonyi, Graham Mustoe, Vilem Petr

This paper presents the results of an experimental and numerical investigation of the shock wave energy transmission and reflection through boundary layers (joints, fractures) or between inhomogeneous geomedium with different physical properties. The conclusions drawn significantly clarify the dynamic failure mechanics because of shock wave energy transmission and reflection through different rock materials and their jointed interfaces. Thorough studies were performed to document the transient, two dimensional deformation characteristics, the normal and shear stress fields for inhomogeneous geomedium focusing on the influence of the internal geometrical shapes, relative density variations and packing of the grain boundaries.

Jan 1, 2002

By Geoff Baldwin, Alastair C. Torrance

The use of monitors to assess equipment performance is carried out on a routine basis in many industries. The benefits gained through process control in knowing exactly how the equipment is working far outweigh the initial capital costs of the monitor. In the mining industry several dragline monitors have been developed and installed on equipment through out the world, but to date none has been fully accepted by the industry. This paper describes the use of a sophisticated monitoring system which incorporates an onboard processor to assess both dragline and blast performance. The use of a radio telemetry link for data transfer has removed the need for manual data collection and transfer, leading to a more efficient and powerful system. Significant effort has been put into the development and verification of a dig index to allow blast performance to be objectively assessed.

Jan 1, 1990

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By Henry P. Van Ormer

This paper is written to outline the capabilities and flexibility of the electric motor driven oil cooled rotary screw air compressor in construction and mining applications. With the changing economics between fuel and electric power all over the world, the viability of the electric motor is a choice all construction and mining people should be aware of. The advent of large efficient electric motor driven rotary screw compressors have given a great deal of flexibility to the use of these units on many applications not considered before. Examples are given for rotary and percussion drilling, fennels, and underground, sandblasting and "uniting, general uses - shows wheel mounted and skid mounted units.

Jan 1, 1976

By Roger L. McCarthy, Ali Reza

The use of an ammonium nitrate-fuel oil (ANFO) explosive in the Oklahoma City Federal Building bombing has led to a renewed interest in using additives during the manufacturing process of ammonium nitrate to render it non-detonable. Suggested additives include calcium carbonate, which is already used in some European countries, and mono-ammonium phosphate (MAP) or di-ammonium phosphate (DAP), which are the primary desensitizing agents claimed in US patent 3,366,468, Method for desensitizing fertilizer grade ammonium nitrate and the product obtained, issued Jan. 30, 1968 (Porter, 1965).

Jan 1, 1999

By P. Katsabanis

Numerical modelling was used to examine damage in wall control operations. Decoupled charges appear to create larger damage zones than fully coupled low density charges with similar charge distributions: Air was shown to be a very efficient coupling medium, while water coupling resulted in significant damage. However, Mach stems are formed when air is used as a decoupling medium, leading to compression of the charge ahead of the detonation wave. Air decked charges generate two damage zones, one close to the charge and another close to the air-deck/stemming interface, where pressure pulses are reflected. The extent of the latter depends on the length of the air-deck.

Jan 1, 2001

By Jim Daley

SEE is a dynamic organization composed of people from all facets of the explosives industry who are truly interested in the advancement of that industry. I had been a miner at the Homestake Gold Mine in Lead, SD for 12 years when I decided to obtain a mining engineering degree. The mental and economic consequences of that decision were more severe than we had imagined. The joint scholarship program of the Northern Plains and Black Hills Chapters of SEE provides assistance to several college students each year. I was fortunate enough to receive scholarships from this program twice and this assistance helped me and my family with both monetary and psychological support during times of need so that we could stay focused on the goal of obtaining a degree.

Jan 1, 1995

By M-C. Lee, Shomaker, R. Turcotte, B. Short

This research program was undertaken to better understand the factors causing abnormal NOx fumes generation from blasting operations in surface coal mining. More specifically, unusual quantities of nitrogen dioxide and nitric oxide have been observed at several surface coal mines in the Powder River Basin, Wyoming. All these mining operations have several points in common: (i) Blasting is performed using gravity loaded emulsions or emulsion/ANFO blends (ii) Unusual NOx (Oxides of Nitrogen) emissions are observed mostly when blasting is conducted in the overburden as opposed to the coal seam itself (iii) The overburden consists of very weakly consolidated ground strata, providing relatively weak confinement conditions for the explosives, and (iv) Significant ground water is observed.

Jan 1, 2002

By Kis M

The purpose of seismic control of blasting is to indicate the vibration magnitude or to eliminate the occurrence of vibration damage caused by blasting. At the Mining Research Institute in Hungary, a new method has been developed to determine the method of delay. Near the blasting site (within 100-200 meters), the peak value of the particle velocity is determined by calculation and also by measurement. In the calculations, the time error of the electric detonators is taken into consideration. During the test program, the results of the experimental blasts and the calculated data have shown good correlation. The method of calculation helps the operator eliminate vibration damage, while the greatest quantity of charge can be detonated.

Jan 1, 1979

By Robert Lee, Jay Rodgers, Kirk Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000

By Steven V. Crum, Willard E. Pierce

Concern has been raised about the adequacy of current regulatory guidelines designed to protect homes from unwanted blast damage due to low frequency ground vibrations; in particular those with predominant frequencies below 6 Hz. This report summarizes and updates the preliminary results of a continuing Bureau of Mines investigation which will be completed later in 1995. Four structures at four different surface coal mines have been studied by examining their response to ground vibrations created from overburden blasting. House response to ground vibrations with dominant frequencies down to about 3 Hz were recorded. Many of the blasts produced ground vibrations with peak amplitudes above expected crack-producing thresholds. Response motions were compared to those predicted by theoretical single degree of-freedom response models.

Jan 1, 1995

By Walt Meglasson

"Developing technologies in demolition equipment and processes have produced a newsophistication within the demolition industry. Yet, with increasing frequency, owners,architects, engineers, and contractors reject out of hand one of the safest and most effectivetools in the demolition industry today, specifically the use of explosives and blastingtechniques in man_made structure removal. The use of explosives in any application mustbe considered as a tool, no more or less dangerous than any other type of tool, when usedproperly. Accordingly, importance must be attached to recognizing the skill, integrity, andcare of those who use it. Massive amounts of information and help are available to assistthe rock blaster, ranging from the practical to the highly theoretical, but very littleinformation exists to guide anyone considering unleashing the power of explosives instructural demolition blasting. The planning and work required to execute such projects iscomplex, and the recognition of the different applications explosives can be applied to isthe first step."

Jan 1, 1993

By Clive-Workman Davies, K K. Kabongo, Mensah Frimpong

Given the capital intensity of the dragline operation coupled with rising cost of explosives, the onus is on mine operators to make maximum use of explosives in blasting to assist dragline diggability. At a surface coal mine in South Africa large boulders necessitating secondary breakage and in some cases completely unfragmented sections of a blast resulting in low dragline diggability were encountered in the interburden blast. Twelve blasts were therefore closely monitored and dragline productivity evaluated. The ultimate aim was to improve the overall blasting performance and hence increase dragline productivity. Three areas were in focus; fragmentation assessment, dragline productivity assessment and cost analysis. The studies indicated unsatisfactory explosive and initiation performance, problematic blast design and questionable operators performance. It is established that dragline cost account for 60% of the total mining cost whereas the drilling and blasting cost account for the remaining 40% and that improvement in dragline productivity results in automatic cost saving.

Jan 1, 1996

By R W. Bellenie, P N. Blakey

The phenomena of post detonation gases in muckpiles is reasonably well known. It causes the 'rumbling' noises occasionally heard after a blast in open pits or quarries and is thought to occur due to initiation of carbon monoxide, hydrogen, etc. by 'hot' spots within the muckpile. The problem usually occurs with highly aluminized products, but can occur with any oxygen deficient product. This phenomenon was never a problem underground due to restriction on access to blast areas, ventilation criteria, etc. until the advent of large diameter blastholes and particularly their use for specialized applications such as drilling for blasting down 'hang-ups' in ore passes.

Jan 1, 1980

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By Chantale Doucet, Mario Paventi, Malcolm Scoble, Yves Lizotte

Laboratory studies in homogeneous material indicate that the area of new surfaces created by blasting is proportional to the energy imparted to the material. Field studies, however, show that fragmentation is also related to the rockmass structure. This paper reviews ongoing compilation of a comprehensive and integrated blasting database which is based upon field monitoring and laboratory testing. A priority application of the database is to support attempts to more fully understand structural control over fragmentation. Database construction and the relative importance of rockmass physical and mechanical properties are considered in the paper. A methodology for data collection prior to, during and after blasting is reviewed. Data summaries from three case studies of blast performance in surface and underground mines are presented. These illustrate various aspects of the methodology, which included image analysis to quantify the fragment shape and remnant geology evident in the muckpile as part of the evaluation of structural control over fragmentation.

Jan 1, 1994

By Dale S. Preece, Lee M. Taylor

Computer simulation of the physics involved in conventional rock blasting can be split into two phases; transient stress wave propagation and rock motion. Because the two phases involve totally different mechanisms and time scales, they must be numerically modeled with two different computer programs. The first phase is usually modeled with a finite element or finite difference code which treats the rock ss a continuum and simulates the transient stress wave and subsequent fragmentation of the rock. The second phase is usually modeled with a distinct element technique where the rock mass after fragmentation is no longer treated as a continuum but as a finite number of distinct particles that interact with each other through collision mechanics.

Jan 1, 1989