Search Documents

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

By Parker GJ

The financing of smaller resource projects has proven to be a difficult problem for promoters and financiers alike as very often such projects have not met the requirements of available financing methods and promoters have equally found it difficult to establish credibility, management and technical ability with potential financing sources. Solutions to the dilemma in which many of these projects find themselves are not readily apparent but will need to be found if the full potential of Australia's resources is to be realised. INTRODUCTION The growth of so called project financing in its present form is normally considered to be a phenomenon of very recent times, however, paradoxically there are references to what could be called financing in the old testament. To confuse the issue further financing small resource projects may not, and very often are not undertaken on a project financing basis. It is therefore quite apparent that one should be completely clear on:

Jan 1, 1982

A great part of the research on froth flotation of gold ores deals with ores containing gold associated mainly with sulphides, resulting in a largely accepted view that what takes place with sulphides (eg pyrite) in a flotation cell also happens to gold particles. This paper is concerned with the influence of some inorganics (CuSO4, CaO and NaCN) on gold particles flotation, using ethyl or amyl xanthates as collectors. The bench-scale tests were carried out with ground quartz and gold particles mixtures. Some findings stemmed from this study: flotation of the gold particles of size 0.16 mm was efficient adding only frother; larger gold grains were better recovered by the use of stronger collector CuSO4 did not seem to be an activator for gold; the addition of NaCN up to 200 g/t or CaO up to 2000 g/t did not depress the gold grains when amyl xanthate was used as collector although with ethyl xanthate the gold depression was verified.

Jan 1, 1993

By Moore R. F, Macias L. F

The Filbara region of northwestern Western Australia contains several known occurrences of mafic/ultramafic rock assemblages which may host platinum group element (POE) mineralisation. This paper deals with occurrences at Munni Munni and Andover. The Munni Munni complex is of particular interest because it is known to contain PGE mineralisation and is currently undergoing active exploration. The US/Australia Joint Scanner Project of October 1985 collected airborne scanner data for the BMR over Munni Munni. Such an ultramafic-mafic complex had not been previously researched with advanced remote sensing instrumentation. Extensive investigation of data from the NSOO1 (Thematic Mapper Simulator) scanner resulted in successful differentiation of gabbroic and ultramafic rocks, and also subdivision within the ultramafies. Similar differentiation could not be achieved using conventional Landsat MSS imagery and aerial photography. Encouraged by those results and in support of BMR field research into the mafic-ultramafic suites of the region, data from the Landsat Thematic Mapper (TM) instrument were investigated to attempt differentiation of the ultramafic and mafic rocks in the Andover complex some 50 km to the northeast of Munni Munni.

Jan 1, 1988

By Lawrence PR, Hoffman W

The dissolution of gold from various ore-bodies is discussed in terms of extraction rates and reagent consumptions during leaching. Gold dissolves slowly in cyanide but reagent consumptions are usually satisfactory. In almost all cases where excessive cyanide consumptions occur, similar high consumptions result with other lixiviants. Recovery of gold from cyanide solution is well established and comparatively simple technology.Gold dissolution in thiourea is faster than cyanide but significant consumptions of thiourea, due to both adsorption and oxidation, occur. Gold recovery from thiourea solutions is likely to be more difficult than from cyanide.Chlorination of gold is very fast in acidic conditions but excessive consumption of chlorine occurs for ores containing greater than 0.5% S. Reprecipitation of gold and handling of acidic chlorine solutions are both significant problems. The mechanism of gold reduction onto activated carbon creates difficulties in the carbon in pulp process for recovery of gold but means a simplification in the production of bullion from loaded carbon.

Jan 1, 1984

By R Espinosa-G=mez

Industrias Pe±oles, S A de C V (Pe±oles) in Mexico, is a major silver producer. The Pe±oles mining division has eight operations and the flotation process in seven of them to concentrate the metal and mineral values. Common metal and mineral values are: metallic gold and silver; gold-silver alloy (electrum); silver sulfide minerals (acanthite, pyrargyrite, freibergite, proustite); lead sulfide (galena); zinc sulfide (sphalerite); and copper sulfides (chalcopyrite and bornite). This paper aims to share Pe±olesÆs mineralogical and metallurgical information on the seven operations where the flotation process is used. Some basic conclusions are drawn from this analysis. Some of the information presented includes: types of orebodies, concentration processes, concentrator throughputs, head grades, concentrate grades and recoveries. Importantly, grind size and liberation values for the main mineral species are presented along with the relationships between sphalerite liberation and its recovery, and galena liberation and its recovery. Also included are three mineralogical case studies: maximisation of silver recovery at the Fresnillo mine producing a silver-zinc concentrate; options to improve gold recovery at the Tizapa mine; and sphalerite iron content for the different orebodies.

Jan 1, 2005

Having successfully applied computer techniques to open pit mining applications, many software developers are now using their skills to tackle the much harder areas of underground mine design, planning and production.Dramatic improvements in the performance to price ratio of hardware (including high resolution graphics screens), a better understanding of the techniques of surface and solids modelling (and their subsequent display), moves towards standard user interfaces and advanced concepts of representing grade distribution in the ore body have all contributed to the recent increase in underground mining software activity.This paper details the general requirements of a workable underground mining software system, providing a minimum checklist of desirable features and emphasises the importance of ease of use, flexibility and intuitive feel. Some relevant trends in hardware, software and application techniques are highlighted and comments made on areas which require further development or are only available in a small number of packages.Finally, a comment is made on the role of computer models to provide a unifying medium for tying together all aspects of underground design, planning and production.

Jan 1, 1992

By the 1990's Australia could be the largest coal exporter in the world and one of the few industrialised countries potentially able to supply the shortfall in its domestic oil requirements by utilizing its oil shale and coal resources to manufacture synthetic oil. The major challenge to both industry and government in implementing the new role for Australia will be to ensure that their actions and policies enable the timely mobilization of resources needed to meet the potential demand for energy, both domestic and overseas. Australia's potential for coal production and exports and for the production of oil from shale and coal are discussed and the potential constraints to development Examined.

Jan 1, 1981

By Chisholm J. M

Why go to the CIS? The vast mineral potential of the Commonwealth of Independent States (CIS) has long been recognised, but it has taken the lowering of the iron curtain to open up the region to serious mineral development consideration by the Western World. The advent of a free market economy and the emergence of the Independent States with pressing needs for foreign investment has led to a greatly improved investment climate. Coupled with the desire for some of the more entrepreneurial resources companies to head the wave of investment to the region, this sequence of events has promised a great deal, but delivered only modest progress to-date. Potential gold project development has provided the major focus, for three reasons: the region is highly prospective for gold, gold projects tend to have a relatively lower start-up capital cost compared to base metal and fossil fuel projects and finally bullion or refined gold is more readily transportable and easier to sell.

Jan 1, 1996

In order to fully understand why Amax Coal puts such extreme emphasis on the drilling and blasting programs at each of our mines, we must review the past. This paper will discuss the drilling and blasting techniques we used in the 1970s and their evolution to current practices. As time progressed, major changes influenced the surface mining of coal through new more restrictive governmental controls and local communities organising into groups with two goals in mind, one to shut down the mines and the second to try and get rich by making false and unjust damage suits against the mines. In virtually all of our midwest surface operations we have at one time or presently are facing litigation that has reached into the millions of dollars. Amax Coal has worked in co-operation with the United States Bureau of Mines in the areas of blast vibration, shot design, highwall safety, blast casting studies and many more. Today we are continuing to work with Dr David Siskind and his expert staff seeking answers to old and new problems addressing the blasting of overburden and parting seams.

Jan 1, 1995

By M N. Ingham

X-ray fluorescence (XRF) spectrometry has always been considered to be a comparative method of analysis. Reference materials are required to calibrate the analytical system. This paper describes the use of a set of æsyntheticÆ oxide standards, made from commercially available high purity compounds, to calibrate a spectrometer for 21 major and minor oxides. The spectrometer software uses simple methods of background correction, and a fundamental parameter method of matrix correction. Sample preparation is by fusion in 66 per cent lithium tetraborate, 34 per cent lithium metaborate. The use of synthetic standards, made from traceable compounds, brings XRF significantly closer to being a primary rather than a comparative method. Reference materials were used to validate the method described and examples of accuracy for major constituents are given using ores and other minerals. This method has successfully been used to analyse a wide variety of minerals and ores, as validation data shows. A titanium process example clearly shows the benefits of highest accuracy analysis.

Jan 1, 2008

By Oliveira JF

Thiourea is an alternative reagent for cyanide in gold leaching. The recovery of gold from acidic thiourea solutions by adsorption on activated carbon is based on methods similar to those applied for the extracting of gold from cyanide solutions, but the mechanism involved in the process is not completely understood. In the present work, studies were carried out to evaluate the adsorption of gold onto activated carbon. Experimental data showed good agreement with both the Freundlich and Langmuir isotherms. The adsorption of gold from acidic thiourea solutions proved to be an endothermic process, while the adsorption from cyanide is known to be exothermic. The isosteric heat of adsorption of -11.3 kcal/mol in the early stages of the adsorption is an indication of a process involving chemisorption. The effect of temperature was studied between 15¦C and 55¦C. An activation energy of 3.5 kcal/mol was determined by the Arrhenius plot, which indicates that the controlling step in the kinetics of adsorption is the diffusion onto the porous structure of the activated carbon.

Jan 1, 1993

By G T. Hefter, P Singh

Sulphur dioxide oxidation is an attractive alternative anodic reaction to the evolution of oxygen in copper electrowinning. Accordingly, the electrochemical oxidation of SO2 in aqueous 1.0 x 10-1 mol/L NaClO4 has been studied at pH 2.3 using platinum and glassy carbon electrodes. On the platinum electrode SO2 oxidation occurred on the forward scan at 0.96 V and on the reverse scan at 0.63 V. For GC, a single SO2 oxidation peak occurred at 1.40 V on the forward scan. SO2 oxidation on both electrode substrates was hampered by oxide layer formation. The electrode could be reactivated however, by oxide layer reduction. Although reactivation was most successful for platinum, SO2 oxidation on platinum is quite complex, with this evidenced by the reverse scan anodic peak. Glassy carbon shows simpler behaviour and thus, is the preferred substrate for SO2 oxidation.

Jan 1, 1998

By B J. Fallon

This study used structural equation modelling (SEM) to develop a series of models to explain the impact of work-life balance on employeesÆ perceptions of job performance, job satisfaction, turnover intentions and absenteeism. The sample comprised 257 participants (108 males and 149 females) from a range of occupations and levels of seniority. In sum, the results clearly demonstrated that successful work-life balance is associated with higher levels of job performance and worker satisfaction and with decreased levels of absenteeism and turnover intentions. The data also lent support to the impact of employeesÆ coping styles, schedule flexibility and supervisor support on employeesÆ abilities to balance work and life. It is concluded that tangible benefits to an employerÆs bottom-line can be anticipated from organisational initiatives to assist employees to better balance their work and personal lives.

Jan 1, 2005

Most mining projects will involve some level of financial markets price risk. This is because commodities are generally traded in $US. The project will also incur costs in $A and if based in Australia will seek to generate a return in Australian dollars. Therefore the project faces commodity, foreign exchange and interest rates risk. As a business you may wish to maintain these risks within your business. However if the project requires financing to be provided then the financiers will want to ensure that there is a level of certainty attached to the cash flows to support the debt repayments. This is achieved by hedging the financial market risks. Traditionally the hedging process has been based on underlying assumptions within project models, which incorporate views on the direction of the underlying price risk. These views can be formed in an ad hoc manner. Gathering information from a variety of sources including economic forecasting and modelling, technical analysis, seeking market expert views. However, given the historical accuracy of such forecasts locking into long-term fixed hedging arrangements can create an inflexible environment that can restrict the opportunity to benefit from the underlying volatility of financial markets.

Jan 1, 2003

By D Manhire, G Hogan, M Ryan, S Whiteley

Site restoration at the L&M Mining Limited alluvial gold mining project at Waikaka near Gore, Southland is described. In 2000 mining operations started to recover alluvial gold beneath historical dredge tailings over 244 hectares in the flood plain of the Waikaka Stream. The project had an eight to nine year mine life but was prematurely closed in 2002 because of economic considerations. Restoration of the site back to pastoral farming, with shelter-belt and amenity tree, shrub, and wetland plantings is described. Dealings with the landowners and regulating authorities are addressed in the paper.

Jan 1, 2003

Most Geologists have a well rounded knowledge of the exploration phase and those who have worked as mine geologists have an understanding of the production phase. Few have had exposure to the development and the construction phases. Even fewer have had the experience of closing a mine, disposing of the plant and equipment, carrying out the final cleanup and making the area safe and environmentally acceptable.During the various phases of exploration, the geoscientist gains a wealth of non-geological information which can be of considerable value to engineers and technicians in the feasibili-ty, development, operation phases and finally the closure of a project. Such basic controls as surveys, adopted assay sample lengths and the location of items of infrastructure during exploration, may continue to affect the project through its entire life. Thus the geologist's responsibilities extend well beyond the explo-ration phase of a project.

Jan 1, 1990

Today's emphasis on the enterprise bargaining process must be seen as an opportunity for organisations to further develop occupational health and safety standards at work. In particular, this shift from a centralised industrial relations system to employer, employee bargaining, presents organisations with an excellent opportunity to develop OH & S at the `shop floor' level. This is despite real difficulties in presenting hard data on the cost benefits. Unfortunately, examination of enterprise agreements ratified by the Australian Industrial Relations Commission (AIRC), show that less than 32 per cent contain provision for occupational health and safety. Those addressing the issues of occupational health and safety have included segments such as: ò rehabilitation activities; ò a new emphasis for workplace occupational health and safety committees; ò formalising procedures related to hazard identification and control; ò the use of personal protective clothing; and ò occupational hygiene and health monitoring issues. For example, an enterprise agreement reached between CIG-Gases and their unions, included clauses which commit employees to attending ten safety meetings and two work place inspections each year, in order for them to receive any further pay rises.

Jan 1, 1995

Exploration of a coal deposit provides the data on which a range of mine plans can be developed during project feasibility. The stages of exploration use methods and procedures which initially outline the deposit with more detailed data gathering and analysis of the specific site complexities. The in situ coal resource and reserves are calculated. The mine plan is a function of the mining method chosen and can have significant impact on the recoverable reserves. Other factors which can impact on the recovery of the reserves and the ability to maintain planned production levels are those which were either undetected during exploration or were misinterpreted. Exploration programs should be detailed enough to minimise to an acceptable standard the recognised and potential risks. Past programs which explored to achieve a minimum exploration density required to satisfy measured reserve status have generally proven to be inadequate, placing reserves and production at risk.

Jan 1, 1997

By Lindbeck K

The mining industry in Western Australia is a large sector of the WA economy providing $12 billion (1993) of the export income for the State. Historically, mining in WA developed from traditional prospecting in the late-1880s leading to major underground operations by the turn of the century. Large open pits were developed in WA following World War II and became increasingly common since the gold boom of the 1980s. With the development of the open pits has been concomitant evolution of mining legislation, principally the Mining Acts of 1904 and 1978, which has been also accompanied by a practical evolution of the administrative system within the Department of Minerals and Energy. The mining industry has recognised the need for sound environmental management at mine sites, taking up the challenge and becoming a world leader in rehabilitation techniques. Any environmental management program in the industry has three stages: approval by government; management by the industry; and return to the State in an environmentally acceptable condition. The WA environmental requirements, procedures and industry performance in these three stages are discussed.

Jan 1, 1994