Search Documents

By R. J. Miller

Mechanized Roof Supports (MRS) have dramatically improved safety and productivity of retreat pillar mining in coal. Due to low capital cost and greater flexibility, retreat panels have in some cases approached the productivity of a longwall. Because of improved safety and rapid set-up time when compared to conventional timbering, MRS are driving a return to retreat pillar mining in many situations. This paper describes how panel layout can be optimized for safety and operational efficiency when using MRS for retreat pillar mining of coal. The potential for significant unit cost reductions will also be addressed.

Jan 1, 1996

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By Daniel A. Thome, Robert C. Janke

"Installation of permanent soil nails through distressed mechanically stabilized earth retaining walls is a cost effective and aesthetically pleasing solution when using the appropriate equipment and drilling methods for installation. A forensic investigation was performed on an existing mechanically stabilized earth retaining wall to determine the possible causes for the excessive horizontal displacements and visual structural flaws found along a portion of the wall. Reports concluded that the visual shifting was due to a number of factors including improper drainage in the vicinity of the wall and unsuitable compaction of the backfill material. Conceptual designs were proposed to the owner and the installation of permanent soil nails through the existing precast panels was determined to be the most practical solution. A total of ninety-three permanent soil nails were installed to lengths of up to 40 feet (12 m) through sand backfill and silty day fill using a hydraulic rotary percussion drill attached to a tract mounted excavator.IntroductionThe Illinois State Toll Highway Authority awarded Contract RR-03-5144 in the summer of 2004. Construction work for the project consisted of the rehabilitation of two existing concrete culverts and approximately 100 linear feet (31 m) of mechanically stabilized earth (MSE) retaining wall. The retaining wall is located below the southbound lanes of the Tri-State Tollway near the intersection of Federal Highway 41 in Wadsworth, Illinois as shown in Figure 1.Reports were prepared by Applied Technologies in cooperation with Giles Engineering Associates to determine the condition of the MSE wall and recommended conceptual designs to extend the service life of the wall.Nicholson Construction Company (Nicholson) wasselected as the design-build geotechnical subcontractor to install the recommended permanent soil nails through the existing precast concrete panels of the MSE wall. Rehabilitation of the wall involved the installation of ninety-three permanent soil nails through the existing wall, along with soil nail verification tests and proof tests on production nails."

Jan 1, 2005

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By M. Yavuz

Due to workability difficulties, people have begun to use iron ore much later than gold, copper and bronze. In addition, iron and steel products are the most commonly used metals which are necessary for human life today. It is a fact that iron ore is raw material of the steel production process as known. Iron&Steel sector is plays an important role in the economic development of countries all over the world. Therefore, the amount of production and consumption of steel is one of the basic indicators of industrialization all over the world. The amount of steel consumed per capita of the country is considered as a measure of development. The world average per capita consumption of steel is around 210 kg in 2007 (Yildiz, 2009).

Jan 1, 2010

By P. R. Taylor

Diamond films have been successfully formed in an inductively coupled plasma (ICP) chemical vapor deposition (CVD) system from several gas mixtures: CH,-H,, C2112-112, and C2112-112-02' Our previous thermodynamic study indicated that the substrate temperature could be lowered by the presence of oxygen species at moderate system pressures (0.3-0.5 atm) and that higher volumetric growth rates required a high temperature source and a moderate pressure system in CVD processing. The principal experimental results were consistent with the thermodynamic predictions. The deposited films were characterized by laser Raman spectroscopy, scanning electron microscopy, and X-ray diffraction. The films were well faceted and uniform, with the growth rates over 10 pm/hr on molybdenum substrates. The crystal size ranged between 1 and 2 microns for a two hour experiment. It was possible to decrease the substrate temperature to below 800 °C in this system.

Jan 1, 1995

"Chairman: Dr N. G. W. Cook Rapporteur: Mr M. P. RobertsPapers:Planning open pit mining operations using simulation by A. Bauer and P. N. Calder Simulation for control of underground liquid flow by G. N. Pitts and P. B. CrawfordEvaluation of production strategies in a group of copper mines by linear programming by P. H. Williams, J. N. Brooke and D. M. PoulterAn equipment maintenance system by D. W. Dean and J. A. RyderTaken as a whole, the difference between the four papers in this session were perhaps more illuminating than their similarities. The titles of the first and second papers contained the word 'simulation', and in both papers random number generation was relied upon in the selection of inputs from empirical distributions, but the nature of the models to which these values were inputs were quite different. The third paper displayed another method of uniting the empirical and the theoretical in a linear programming formulation whose matrix coefficients were measured empirically, and here some apt remarks on computer implementation were included. This paved the way for the last paper which abandoned all theoretical pretensions in favour of a detailed description of computer implementation and perhaps as a result gave rise to the most feeling audience participation.The systems mentioned were developed for the iron, petrol, copper and gold producing industries in the US, Canada, Zambia and South Africa..As with all the parallel sessions, contributions from the floor may have been limited by the shorter time available to delegates to acquaint themselves with the papers before the session. In spite of this, and due largely to the active chairman¬ship of Dr Cook, the discussion during the session which is summarized here contributed much to the information contained in the papers themselves.In his presentation, Dr Calder summarized his paper. He expected that simulation would be used in future on an almost universal basis in open pit mining. It could contribute new knowledge more cheaply than experimentation in the flea For example, this study had shown what was previously thought to be a matter of more shovels and trucks was really a blasting problem, and improving blasting had increased production to the desired level. The simulation had shown that uniformity of truck performance was a desirable factor. It had also been used to study the advisability of a dispatching system.Dr Ramani contended that where equipment characteristics were available, deterministic standard simulation could adequately simulate systems in which interference occurred. Operator performance could be measured against perfor¬mance curves predicted by standard simulation and poor operators spotted and retrained. The present system did not take into account variability in truck loading, for instance. Dr Calder replied that if the number of variables was large, the standard approach became too complicated for operating personnel to follow. He admitted he had not tried it. The variability of truck loading could be coped with easily using the Monte Carlo approach. Operator variability was already incorporated because the time studies are actual."

Jan 1, 2014

By P. Thapliyal

The petroleum refining industry generates over a million tons of spent catalyst per year, containing valuable metals. Currently, these materials are recycled to smelting furnaces, but the fundamental mechanisms controlling the recovery processes are poorly understood. Furthermore, submerged injection of finely divided materials is potentially a means to obtain high recoveries of pay metals. In this study, a catalyst containing 10% Ni and 1% Co was injected into 45 kg heats of matte. A copper matte was chosen so that the nickel and cobalt recoveries were measurable. It was found that the recovery ranged from 40 to 700Al, increasing with catalyst feed rate, decreasing with catalyst particle size and decreasing with the oxygen content of the carrier gas. A mathematical model was developed to account for the results, and to permit extrapolation to nickel mattes. The industrial implications are discussed.

Jan 1, 1996

By H. Ban

Triboelectrostatic separation tests were performed on a bench-scale, analytical separator using coal, coal combustion fly ash and mineral samples. Fractions of separated samples were collected and analyzed to characterize the performance of the separation. Particle size distribution and morphological characteristics for these samples were analyzed by optical microscopy, and scanning electron microscopy (SEM). It was found that smaller size fractions of a fly ash sample had better separation than the full sized parent fly ash sample, indicating interference or particle-particle interactions during the separation process. It was also observed experimentally that small kaolin particles attach to the surface of large silica spheres, causing charge neutralization and subsequent low separation efficiency.

Jan 1, 1997

By B. Papilon

Dynamic pressures during blasting can affect performances of both electronic and non-electronic detonators. Boreholes can develop tremendous amount of pressures during blasting. The effect of such elevated pressure especially during electronic delay countdown is probably more acute in electronic detonators. Measuring the pressures during blasting can aid to understand the relationship between magnitude of the pressure developed and the multitude of blasting conditions.

Jan 1, 2013

By Charles Zimmerman

The Genesis gold mine, owned and operated by Newmont Gold Co., is located in section 31, T36N, R50E within Eureka County, Nevada along the Carlin Trend of sediment-hosted disseminated gold deposits. Mining commenced in 1986 with present mineable and stockpiled reserves listed at 17,711,000 tons of ore averaging 0.073 opt Au, totalling 1.292 million ounces of gold. Ore is primarily hosted within Devonian calcareous siltstones that have been subjected to intensive argillization and silicification episodes. Additional mineralogic and geochemical features of the Genesis ores include enrichment in iron-oxides, kaolinite, arsenic and antimony; the ore zone is relatively depleted in carbonates and sulfides as a result of supergene and hypogene oxidation. Two major structural zones enhanced the permeability of the siltstones and served as the main hydrothermal conduits within the deposit. Prior to the main ore stage, the host rocks were subjected to metasomatic effects caused by emplacement of the Juro-Cretaceous Goldstrike granodiorite pluton and associated dikes and sills. Micron-size gold occurs in clays, micro-crystalline quartz, and in arsenical complexes. Non-oxidized carbonaceous and sulfidic ores and silica-locked ores result in variable preg-robbing and refractory responses during cyanide recovery. Selective mining and milling has resulted in the successful treatment of the Genesis orebody.

Jan 1, 1988

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By C. Patrick

Annually, the U.S. coal industry generates and must dispose of over 200 million tons of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks, used for under-ground ventilation stoppings, with refuse blocks. Refuse was collected from three active preparation plants in Eastern Kentucky and used as the primary aggregate for concrete cylinders. The refuse fell within ranges normally observed for size consist, moisture, and ash. Stress-strain analyses yielded compressive strengths of the refuse cylinders from 59% to 77% of the control group strengths. Low variability within groups while significant differences between groups were found. On-going determination of effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1995

By Alexander Smith

"The three principal known mineral deposits of the Taku River area lie in the Tulsequah synclinorium. The axis of this north-south trending structure is along Tulsequah River valley; about 6 miles east of the eastern contact of the Coast Range batholith.The one proven mine of the area, the Polaris-Taku, is on the west side of the valley. It is a gold property, the gold occurring in fine needles of arsenopyrite disseminated in carbonatized volcanics. The mine was originally called the Whitewater, and the adjacent area the Whitewater gold belt. During the years 1937 to 1942 gold having a value of $3,284,000 was produced from 313,500 tons of ore milled."

Jan 1, 1954

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

By G. Brien, O&apos

Selective in-plant breakage was investigated at a Central Queensland, Australia mine. Component seams and size fractions from in-plant samples were characterized petrographically and probability analysis of vitrinite reflectance data used to track the distribution of seam proportions through the plant. Results show that the 2 seams reported differentially to coarse and fine circuits, mainly as a function of coal type rather than rank. Seams were also preferentially concentrated in different size fractions of the coarse circuit. Breakage in the coarse coal centrifuge generated approximately 4% of -0.5 mm fines, but was not seam specific.

Jan 1, 1996

By G. Q. Zhou, H. C. Liang, X. D. Zhao

"This study describes the strain behavior in vertical shaft lining (VSL) embedded in thick soil deposits and its application in assessment of concrete deterioration. The observed strain in VSL continuously decreased companied by a sinusoidal fluctuation due to the influences derived from negative skin friction (NSF) and temperature. The increase in strain increment between peak and trough at each year and compressive strain level as the servicing time continued and VSL depth increased implies that the concrete strength was attenuated, and this attenuation was significantly dependent on the existing compressive strain level in VSL. The reliability of the proposed approach was validated by Schmidt Hammer Technique (SHT) – based concrete strength, and is applicable in concrete assessment and then fracturing prediction of VLSs in thick soil deposits.Concrete strength, Field monitoring, Strain behavior, Vertical shaft liningINTRODUCTIONOver 100 VSLs in Southeastern China subjected to an unpredictable fracturing as shown in Figure1, and there are over 1,000 VSLs embedded in thick alluvium su?ering from challenges of damaging and potential fracturing (Cheng, Yang, Zhou, Li, & Hu, 1993; Zhou, Cui, Lv, Huang, & Chen, 1999; Li & Li,2005). Therefore, a reliable assessment of these VSLs is significant to the normal servicing of mine shafts and the recycle of underground space when these mine shafts were closed.The continuous increasing of NSF induced by the drainage of water–saturated deposits well interpreted such extensive fracturing phenomenon, and it is universally regarded as the governing indicator to determine the VSL stabilization (Cheng et al., 1993; Zhou et al., 1999). Based on this recognition, the fracturing prediction and VSL strengthening according to the field monitoring on hydrogeological characteristics, servicing environments, and mechanical behaviors of VSL were carried out (Zhao, Zhou, Zhong, Zhu, & Liang, 2009; Liang et al., 2009; Xie, Lv, & Wu, 2014). As known, the compressive strain level in VSL and the in–situ strength of VSL concrete were the main factors to perform such fracturing prediction. However, the existing studies in literatures were limited to the strain accumulating or releasing behaviors (Zhao, Zhou, Zhao, Kuang, & Hu, 2017), and lack of considering the VSL concrete strength and its attenuation. In this reported study, the in–situ monitoring data on the strain in typical VSLs and the VSL elevations between 2004 and 2014 were initially analyzed. Then, an observed strain behaviors–based approach was developed to quantitatively evaluate the VSL concrete deterioration."

Jan 1, 2019

By A. D. Paananen

With the demand for higher grade feed by the American steel industry and the depletion of the direct shipping ores from the Marquette Iron Range and elsewhere, there was a need to develop the low-grade orebodies. The large reserve of fine grained oxidized iron-formation at the Tilden Mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Preceding the present mining-concentration-pelletizing complex, about 6,500,000 long tons of direct shipping siliceous ore were shipped from the Tilden Mine. Following development of the concentrating and pelletizing flowsheets, engineering and construction was initiated to develop the mine and construct concentrating and pelletizing facilities to produce 4,000,000 LTPY of pellets from this low grade crude ore. Operations started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleveland-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling-Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Due to the non-magnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden orebody have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of des liming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions.

Jan 1, 1978

By A. Siegmund, Gerhard Martin

The recycling of metal containing scrap is a common practice in the industry and has a long tradition. . In rec~nt years, this philosophy has been transferred to organic materials, in particular to thermoplastic polymers. BSB . Recycling GmbH, a company with a long experience in the treatment and recovery of lead from battery scrap,· had recognized this exploitation at an early stage and challenged it by a consequent continuation of the idea to recycle materials other than metals without degradation and maintaining the quality. These efforts resulted in an economic and environmentally acceptable solution producing high quality polypropylene compounds at BSB beside lead and lead alloys from battery scrap. The raw material fair the production of polypropylene compounds is shredded plastics from the separated casings of spent lead-acid batteries. The production of polypropylene with specific physical and mechanical properties is carried out by the accurate dosing of organic as well as inorganic additives. The result of the procedure is a novel product group "Seculene PP", a registered trademark of BSB Recycling GrnbH.

Jan 1, 2000