Search Documents

By Peter A. Rona

The recent discovery of the first black smoker-type hydrothermal venting and massive sulfide mineral deposits at a site in the rift valley of the slow-spreading Mid-Atlantic Ridge near latitude 26°N, longitude 45°W (Rona et al., 1986, Nature, 321: 33-37), demonstrates that a complete series of hydrothermal mineral deposit types exists at slow-spreading oceanic ridges (half-rate = 2 cm/y), similar to the series previously known at faster-spreading oceanic ridges (half-rate > 2 cm/y). The largest hydrothermal mineral deposit known at a seafloor spreading center is a stratiform massive sulfide body with bulk dry weight of about 100 x 106 metric tons in the Atlantis II Deep at the slow-spreading axis of the Red Sea. This observation invalidates the concept that size of a hydrothermal deposit is directly proportional to rate of seafloor spreading. Instead, the occurrence, grade and size of a hydrothermal deposit formed at a seafloor spreading center is controlled by anomalous chemical and physical conditions which may occur at extremely localized sites at the full range of spreading rates. The basic hydrothermal process involving subseafloor hydrothermal convection driven by magmatic heat sources appears to be similar at slow- and faster-spreading centers. However, differences exist in the periodicity of magmatic cycles that energize hydrothermal circulation (104 y at slow-spreading centers; 103 y at faster-spreading centers); in the distribution of hydrothermal sites along a spreading axis (estimated 100 km along slow-spreading centers; 10 km along faster-spreading centers); and in residence time

Jan 1, 1986

By S. Z. Pethö, H. Yilmaz

South Deep Mine is currently undertaking numerous voidfilling projects using low strength aerated cement products. Representative samples from one such site, were taken and tested for the load deformation behaviour under uniaxial loading conditions. The process of sample collection, laboratory preparation and testing are explained in detail. The results of testing were analyzed and the critical aspects pointed out as a design consideration to be implemented as part of the quality control and assurance program. Design aspects and underground application of the aerated cement product are discussed for the particular site on 58 level SV1. A simple instrumentation has been designed and installed to enable monitoring of any future movements in this area. A quality control and assurance process has been formulated enabling all aspects of the support installation in this excavation to be signed off.

Jan 1, 2003

By K Matsui, T Sasaoka, S Kubota, Y Yosh

A large amount of wastes from the preparation plant is produced. The properties of these wastes vary depending on the mineralogical contents of the mother rock in which the coal is embedded. The waste quality depends on the method of mining and cleaning. The waste mainly consists of clays, quartz, carbonaceous materials, mica, pyrites and so on. About 55 per cent of coal-ash is now utilised and the remains are disposed of at the disposal sites, however, the life of the disposal site is limited. Moreover, it is difficult to find new disposal sites. Therefore, it is requested that the percentage of the utilisation of the coal-ash be increased in every field in Japan. So, it is very much available if the injection material for natural/artificial openings can be applied on the cement that is added to flyash. Among the man-made pozzolans, a flyash is probably the most successful component used in grout injection. When flyash is added to Portland cement concrete, the same kinds of oxides as those of the cement are being added. As an injection component, flyash acts, in part, as a fine aggregate and, in part, as a binding component. However, there is not a substantial alteration of the properties of the original component. From these points of view, in order to clarify to what degree the flyash content affects the properties of the injected grout mixture; different combinations of flyash, Portland cement and water were considered by means of several experiments.

Jan 1, 2003

By R. M. Zimmerman

INTRODUCTION Tuff is being considered as a possible geologic median for the underground storage of commercial high level radioactive wastes by the Department of Energy (DOE). DOE has the responsibility for developing or improving the technology fir safely and permanently isolating these wastes. DOE programs must satisfy requirements established by the Nuclear Regulatory Commission (NRC) for the licensing and regulating of these storage facilities (NRC 1981). Pertinent draft NRC requirements are: 1) releases of radioactivity to the environment must be within prescribed limits and 2) emplaced canisters containing wastes must be retrievable up to 50 years following emplacement. High level radioactive wastes produce heat in storage and it is essential that the thermal/mechanical/hydrological response of the host rock will not significantly degrade either the structural performance o£ the repository or the ability of the natural or engineered barriers to retard radionuclide migration. The Nevada Nuclear Waste Storage Investigations (NNWSI) was established by DOE to evaluate the suitability of disposing of high level nuclear wastes on or near the Nevada Test Site (NTS) (NNWSI 1980). NNWSI has focused exploration and site evaluation on the tuffs of Yucca Mountain. Field testing is essential to support site characterization and repository design efforts. Preliminary studies have been conducted indicating that tuffs in G-tunnel on the NIS contain welded and nonwelded tuffs that have similar properties to those in Yucca Mountain. Thus, field testing can be accelerated. This paper discusses the issues supporting the planned field experiments in G-tunnel. Issues not related to rock mechanics are not included.

Jan 1, 1982

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

The beach and offshore gold resources demonstrated at Nome, Alaska are some of the richest found in Alaska. They contain potentially significant resources that may be exploited in the future. Several companies have contributed to the exploration and reserve estimation in Nome offshore gold deposits. More than 3,000 holes were drilled and over 10,000 offshore samples were analyzed in the Nome offshore areas of approximately 40 km2. Those 3,000 plus drill hole logs were converted into digital formats comparable with ArcGIS software. Considerable amounts of mineral resources data were processed and visualized using ArcGIS 8.3 and its geostatistic, 3D analysis, and spatial analysis components. In this study, based on the data processing and visualization results of ArcGIS, a user-friendly website for mineral resource management and utilization is developed using ArcIMS 4.0.1. ArcIMS is a GIS solution to build and deliver maps, data, and tools over the Internet. The Nome offshore mineral resources website presents the geostatistic and GIS analysis information. This site allows clients to access the information and perform ArcGIS analysis, such as interactive data query, and map layers display of the gold resource distribution, average grade, gold reserve, and relative mineral resource estimation via remote computers. With linkage to other related mining web sites, this web site allows users to search for related publications and more flexibly manage the information. A few other appropriate customized tools are also being developed to assist interactions between the server and clients for data analysis and management.

Jan 1, 2005

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

By G. Humphries, E. Wolmarans

The PPRust North project is an expansion of existing operations on the ?Platreef? orebody in the Limpopo Province of South Africa. Anglo Platinum has been mining and processing the Platreef since 1993 at the adjacent Sandsloot and Zwartfontein South open pits at a current rate of approximately 4.5 million tons per annum. This paper describes the origin of the proposed process flow sheet. A comprehensive test work programme has been conducted evaluating the best process flow sheet for the very hard and variable ore in the proposed mining area. The selection of the comminution circuit is discussed where conventional crushing and SABC options were analysed based on both extensive test work and analyses of current operational data at the existing concentrator. The application of the high pressure grinding roll technology has significant advantages?it replaces the 3rd and 4th stage crushing stages in a conventional circuit. This programme has been conducted over several years and has involved work done at site at pilot scale, internally at the company?s research facilities and externally at various sites. The on-site pilot work was completed over a 7-month period at the existing concentrator facility using a ThyssenKrupp-Polysius, ?Polycom?, 950 mm by 350 mm, high pressure grinding rolls (HPGR) machine. In excess of 185 000 tons of ore was processed through the unit during the trial period. This paper describes the test work programme and particularly the proposed application of high pressure grinding technology and its potential for further application in the platinum industry.

Jan 1, 2006

By K. L. Myers, R. Espell, C. Deringer

Construction of the AA Pad reclamation was completed in the fall of 2000. Seeding of the ET cover began in the late fall of 2000 and continued through May of 2001. On Saturday afternoon, June 1, 2002, a large, very localized thunderstorm struck the reclaimed AA Pad site. Eyewitnesses present at the time described a dark storm cloud parked above the site for less than half an hour. Average rainfall intensity was measured to be 122 mm (4.8 inches) per hour and peak rainfall intensity was estimated to be 213 mm (8.4 inches) to 259 mm(10.2 inches) per hour. At the time of the storm, the construction was less than two (2) years old and the vegetation had only a single season of growth. The entire period from the end of construction until the date of the storm was a drought period with below normal precipitation. Other than a few small snowmelt events, there was no precipitation event large enough to produce any significant flow in the channel network. Therefore, the very first significant runoff event was the extreme event of June 1, 2002. The storm essentially represents a large-scale field test of the design concepts used at the AA Pad site. Shortly after the storm, data was collected and analyzed with the intent of learning as much as possible about the performance of the cover system design with the expectation that the newly acquired knowledge might be utilized in future designs to further improve the performance of similar cover systems during extreme events.

Jan 1, 2003

By Quentin Rhoton

To benefit two endangered fish species, waterfowl and other wildlife, and water quality in the lake and downstream, the decision was made to remove levees that had been in place since the 1950s. Because the levee material was mainly dredged up lake bottom peat, it was decided to pare down the sites chosen for breaching with dozers and trackhoes. This material was spread out onsite instead of expensive removal by dumping elsewhere. Because of the instability of the final pared down levees and the lake level being at a ten-year low, it was decided to use explosives to breach four of the sites. After over five months of earthmoving and two weeks of loading holes, the levees were detonated the day before Halloween, 2007. Somehow pumpkins showed up to be part of the explosive activities.

Jan 1, 2009

By John F. Slonaker

This report is a review of current research being conducted in the United States which is intended to increase the utilization of coal ash. In order that this report be as timely as possible, the majority of information was obtained by direct comunication with the people listed in the references. Due to the magnitude of the flyash research program, some projects may be inadvertently omitted. Field research on flyash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University.1 This research is directed at determining the plant nutrients that are available in flyash as well as the quantities of flyash that can be applied to agricultural soil without adversely affecting plant growth, Coal mine spoil and refuse bank reclamation with power plant flyash is being demonstrated by United States Bureau of Mines, Morgantown, West Virginia.2 Numerous highly visible coal refuse piles and strip mine spoil banks contribute to air, water, and land environmental problems. Revegetation of several experimental sites with flyash from bituminous coal-fired power plants was undertaken in West Virginia and Pennsylvania. Conventional farm equipment was used at some of the sites while large earthmovers were required at others. The flyash served as a neutralizing agent, dilutent, and soil amendment to provide some nutrients which enhanced vegetation of the barren areas, Estimated cost of reclamation by this method is $300.00 per acre of previously leveled area. This figure can vary considerably depending upon the topography of the site, haul distance, quality of the soil and quality of flyash.

Jan 1, 1974

By Ben L. Seegmiller

The artificial stabilization of a pit slope at the Twin Buttes Mine near Tucson, Arizona has been completed as part of a practical rock mechanics program. The research program began in June 1971 as a result of the three million ton South Slope slide(1) which caused significant economic and operational problems. Hydrological studies, field and laboratory testing and investigation of various stabilization systems(2)occupied the first year of research. In July 1972 a design for an artificial stabilization test using post-tensioned cable bolts was completed and the selection of an outside contractor was made the following month. The project began in mid-September and was completed during the first week of January 1973. The test site is located adjacent to the South Slope slide in a zone of high potential failure. When the site was initially selected it was thought that it would remain stable at least until the test could be completed. However, heavy rains which fell in late October induced displacement in the half of the test site adjacent to the South Slope slide. Prior to this stabilization test it was thought both impractical as well as improbable that a moving slide could be stabilized with an artificial support system(3). Because the project was nearing the half-way point it was decided that an attempt should be made to complete the test as originally planned. This meant, in effect, that an attempt would be made to stabilize the moving section as well as the stable section.

Jan 1, 1973

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By D. M. Holloway

As a part of the 1-15 Reconstruction Project, static and dynamic (high-strain) testing methods formed the basis to estimate long-term axial capacities, and to assess the magnitudes of bearing capacity gains (setup) from the end of installation to the time of static/dynamic tests weeks later. This paper summarizes the results of nine full scale pile load tests to failure in compression, and how the designers used these data to finalize pile selection and penetration criteria bridge-by-bridge in the final design stages. Soil conditions along the project alignment ranged from deep, lightly over-consolidated Lake Bonneville clays interbedded with granular strata of varying consistency, to sites dominated by dense alluvial deposits of cohesionless soils well above the water table. The test sites were selected to bracket the conditions that are expected. Twelve-, 16-, and 24-inch-OD pipe piles are to be used to support the new bridges. The team plans to impact-drive all piles closed-end to final penetrations. The test piles varied from 35-ft-long pipes driven to refusal in the shallow dense sands at some sites, to 115-ft-long pipes stopping at 3 blows per foot in predominantly cohesive deposits. The capacities gained with time proved to be reasonably predictable, and significant setup was noted both in the cohesive and cohesionless strata. The test program objectives included providing the means to estimate long-term capacities from short-term (24- to 48-hour) restrikes following installation of foundation piles during production driving operations.

Jan 1, 1998

By James W. Cassie

The Snap Lake Diamond Project is located approximately 220 km northeast of Yellowknife, NT, Canada at an approximate latitude of 63?35?. The project location is within the zone of continuous permafrost; measured ground temperatures are about ?2?C at 10 to 20 m depth below surface. The site is located on a peninsula jutting into Snap Lake. The site is generally barren of vegetation, except for some isolated areas with low trees located in topographic lows and near the shoreline of Snap Lake. As part of phased evaluation process with regards to the mining project, an Advanced Exploration Program was undertaken in 2000 and 2001. This program included the underground extraction of a bulk sample of kimberlite, which was processed on site. A Processed Kimberlite Containment (PKC) area was required as part of this program. The area chosen as the PKC facility was a small inland lake, called Inland Lake #1, on the peninsula. Construction of the PKC area required the construction of two dams, one on either end of the lake. At the south end of the lake, Dam 1 was constructed partially on a talik and partially on continuous permafrost. Dam 2 was constructed entirely on permafrost. The effects of the remote location, selection of suitable construction materials and permafrost conditions on the designs of the dams are discussed. A description of the design elements and construction schedule are provided. A review of the performance of these two dams, in terms of settlement, deformations, pore pressures and thermal regime, over the last several years is provided.

May 1, 2003

By John D. Morton, J. H. LaVerne Palmer, Douglas J. Belshaw

An extensive programme of ground instrumentation and observation was carried out for the West Duff in Outfall Sewer tunnel project prior to and during construction, to establish the performance characteristics of the rock through which the tunnel and appurtenant openings were dug and to examine the nature of the lining-to-ground interaction. The existence of high horizontal residual ground stresses was confirmed, and values established by overcoring. Rock deformations and stress changes were monitored during tunnelling. Permanent stress and strain monitoring devices were set into the final lining and these are continuing to operate. INTRODUCTION The site is located on the north shore of Lake Ontario at Pickering, some 20 miles (32 kilometres) east of Toronto, Canada where a variable thickness of glacial or interglacial sediments overlies bituminous shale bedrock of. the Collingwood Formation which is lower Ordovician age. Approximately 50 feet (15 metres) of glacial cover exists at the shaft, though this thins abruptly at the regressing cliffed shoreline such that several small areas of exposed bedrock exist in the lakebed. The general location, overall geological section and detailed site plan and profile are illustrated in Figs.1,2 and 3 respectively. General properties of the rock as established during an extensive test drilling and site investigation programme are listed in Table 1, while stress determination by USER overcoring stress meter device are given in Table ll. These data formed the basis of analyses which were done to examine the intended outfall design, and to detail the construction procedure and the observational instrumentation programme.

Jan 1, 1979

By D Craw, J Pope

The Greenland Group, Westland, can be characterised with respect to environmental issues by the application of a GIS database (DAME), and specific sampling campaigns. Waters draining gold mineralised areas have a distinctive chemistry characterised by neutral pH and arsenic as a trace element. The acid neutralising capacity (ANC) from carbonates usually exceeds the maximum potential acidity (MPA) from sulphides resulting in circum-neutral pH. These waters are readily distinguishable from waters draining coal mine related areas, which commonly have low pH (~4) and low As concentrations (~0.1 ppm). In contrast, dissolved arsenic mobilised from Greenland Group historic gold mining areas is up to 2.4 ppm. This As mobilisation is controlled by the secondary As mineral, scorodite (FeAsO2+2H2O). Maximum dissolved As concentrations increase with increasing pH, corresponding to the increasing solubility of scorodite with increasing pH. Dissolved As is attenuated by dilution, precipitation of scorodite, and/or adsorption to iron oxyhydroxide (HFO). Adsorption to HFO is an important attenuation mechanism in and adjacent to many mine sites. HFO is abundant at mine sites where pyrite was abundant in fresh rock, such as where the mineralised zone is dominated by disseminated pyrite. Pyrite, and resulting HFO, are relatively rare where mineralisation occurred as well-defined quartz veins. Localised HFO occurs also where ankerite oxidises in host rocks. Arsenic output flux (ca. 25 g/day) from historic gold mine sites is commonly less than the natural background flux from mineralised rocks (&gt;5000 g/day).

Jan 1, 2006

By Hee-suk Yun, Dae-jin Hwang, Jeong-woo Seok, Myoung-mo Kim

"In this paper, the accuracy of the data measured by a newly developed displacement measuring system, DPRMs (Digital Pile Penetration and Rebound Monitoring system) and its applicability as a quality control tool were verified by field measurements of pile penetration and rebound for pile driving performed at 3 construction sites and 1 test site. The DPRMs data were found to be much better than handwork data. A new dynamic formula for pile capacities is proposed uses the results of a pilot dynamic load test and the final pile penetration. The ratios of pile capacities obtained by the new formula to those by the dynamic load test were 94%±7.4% in the contrast with 123±28.3% by the 5S formula and 68±24.0% by Hiley's formula. This result shows the superiority of the new formula. The ratios of the maximum compressive stresses calculated by using DPRMs to those calculated by using PDA (Pile Driving Analyzer) were about 90-110±10%. This result confirms the applicability of DPRMs as an overdriving monitoring tool. Two sets of DPRMs were used to measure the 3-D displacement behavior of a pile head at the test site. The more the pile head moves laterally, the less the final set values were expected because of the loss of driving energy, but this trend was not obvious within the limited data obtained at the test site.INTRODUCTIONPile construction monitoring consists of two parts. In the first part, enough capacity of the pile is secured to stand the design load. In the other part, pile damage during driving is prevented. Although several methods can be applied to achieve the first part, PDA is nearly the only tool for measuring pile stress.Several methods such as a static load test, a dynamic load test, an Osterberg cell, and numerous driving equations can determine the pile capacity. Among them, the static load test and the dynamic load test are most widely used. The static load test is advantageous because it has the highest reliability. The disadvantages are as follows: it is costly and time-consuming. Also, the capacity of the pile under construction cannot be evaluated. The dynamic load test has lower reliability than the static load test, but it is cheaper than the static load test, is reliable enough to determine the pile capacity, can evaluate the capacity of a pile during construction, and can offer information about construction conditions such as the pile integrity and the pi le stress during driving. The dynamic load test takes a relatively short time and is low cost compared with the static load test. However, it is still costly, time-consuming, and unnecessary to apply to all piles in the field as a construction measurement tool. Therefore, driving resistance (blowcounts) is commonly measured to confirm the pile capacity at construction sites."

Jan 1, 2005

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024