Search Documents

By G. T. Lapidus, R. M. Luna-Sánchez

In the present study, a series of cyanidation experiments were performed on a bulk sulfide concentrate which contained silver in four distinct phases, to determine its extraction rate, varying the oxygen concentration. The results showed that three of the four phases were refractory, aguilarite (Ag,iSeS) being the only leachable phase, and that the effect of the oxidant concentration is minimal. Mathematical simulations were performed, adjusting only the Damkohler number to adequately fit the experimental data. This model, and the mechanism implied, was compared with that found for acanthite (Ag2S) in a previous study, and the differences between the two discussed.

Jan 1, 2005

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By Donald G. Dahle

Project Payette is a conceptual nuclear experiment under the Vela Uniform program intended to further evaluate the mechanism of seismic decoupling. Vela Uniform is a Department of Defense program to improve this country's capability to detect, locate and identify underground nuclear detonations. This program evolved from recommendations of the Panel on Seismic Improve¬ment, (Berkner Panel), an officially appointed group of noted U. S. scientists. This Panel, taking note of difficulties in detecting the differences between some underground nuclear detonations and some earthquakes recommended a program of increased basic research in seismology. The theory of decoupling, Which involves possible reducing of seismic motion resulting from underground explosions by reducing the coupling or physical linkage between the explosion and the geologic environment, was investigated by Dr. Albert latter and his associates at RAND during the late 1950's. The concept has been further investigated theoretically by scientists of the Lawrence Radiation Laboratory and the Sandia Laboratory. The theory has been tested experimentally under Vela Uniform Projects Cowboy, Dribble and Sterling. The Salmon Event of Project Dribble was a tamped (with the explosive in firm contact with the geologic formation) nuclear detonation 2700 feet below ground in the Tatum Salt Dome. Project Payette, if found to be feasible and if authorized for actual execution, would become a decoupled experiment in the same environment.

Jan 1, 1968

By Dan Eyde

Low levels of thallium were detected in the mine water drainages, and process water discharges of western mining and smelting operations. This required remediation under state regulatory standards, which allow discharges of no more than .0017 ppm thallium in mine water discharges. Influent streams containing thallium can be mitigated to state discharge standards after a single pass through the series of fluidized upflow columns. Test work to determine the optimal flow rates used pilot scale systems at two separate locations treating 5 - 25 gpm of effluent. The test system at the gold mine mimics the full-scale system, which will be based on the existing upflow carbon tanks that have been converted to zeolite columns. The system installed at ASARCO's East Helena smelter has a far more complex influent stream with a high loading of competing cations. Nevertheless the columns filled with CABSORB® are successfully mitigating the thallium contamination. CABSORB® ZS500RW is a product based on the sodium analog of the zeolite mineral chabazite named herschelite.

Jan 1, 1998

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By W. W. Cummings

The Mineral King Mine, owned and operated by Sheep Creek Mines is located in the Purcell mountain range of southeastern British Columbia. Production of lead and zinc concentrates commenced in 1954 some 60 years after the initial discovery. Low cost mining methods have been employed to extract 16,0C'O tons of ore monthly from large ore bodies formed by replacement in limestone. Extensive areas in the limestone are yet to be explored and success in the search for new ore bodies is anticipated.

Jan 1, 1960

By Zhang. L.

Ordered intermetallic PtSb had been synthesized by arc-melted and then sintering treatment. The electro-oxidation of formic acid on PtSb was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results are compared to those at a polycrystalline platinum electrode surface. It was found that PtSb intermetallic was catalytically more active than pure platinum according to the onset potential and current density. XRD and XPS technologies had been used to investigate the crystal structure and electron effect. We think formic acid decomposition on PtSb favors the reactive intermediate route and is not very much affected by the CO intermediate as compared to Pt.

Jan 1, 2005

By Mike Lewis

"Descending several stories down a metal staircase into a shaft spanning a quarter city block -- soon to become Roosevelt Light Rail Station in Seattle, WA -- visitors are greeted with four perfectly round, precast concrete-lined horizontal holes leading deep into the earth. The sound of water trickling out from a small drainage trough can be heard over the faint echoes of construction within. Upon entering, the light is dim, but the air is clear with barely a dust particle flowing through the sunbeams. This type of air quality is only accomplished with diligent controls, and JCM Northlink, the company in charge of building the Northgate Link Extension Project, is taking those measures seriously.Commissioned by Sound Transit, JCM is a joint venture of three companies: Jay Dee Contractors, Frank Coluccio Construction Co. and Michels Corp. The tunnels JCM constructed are intended to provide fast, reliable underground rail service, as well as relieve one of the region’s most congested traffic areas. The $440 million project will connect the Northgate, Roosevelt and University District neighborhoods north of Seattle to the downtown corridor and SeaTac airport further south.The scope of this project includes excavation for two light rail stations, boring of two parallel 5 km- (3.3-mile) long light rail tunnels in six runs and the construction of 23 cross passages. Begun in 2014, Sound Transit estimates that crews excavated more than 382,000 m3 (500,000 cu yds) of soil and installed 7,352 precast concrete tunnel liner rings during the shaft construction and boring phase. Now that tunnel boring is complete, JCM is in the process of constructing the cross passages, which act as maintenance areas and escape routes for passengers. Throughout the entire process, the company has utilized atomized mist to control particle emissions.“Our dust control needs change at every phase of the project and don’t go away until the project is fully complete,” said a JCM safety representative. “We found that different dust suppression technologies were needed at different intervals, but atomized mist seemed to fulfill our needs at every step.”"

Jan 9, 2017

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

Although the mining of metals was well established by the time of the Roman Empire mining skills did not really advance greatly for many centuries. Miners did not have the scientific knowledge to distinguish minerals, to process them, and to obtain the best recovery. Each mine essentially developed its own methods in isolation, most of them dangerous. However, with the beginning of the industrial revolution in the early 18th century there was a rapid increase in mining activity in Central and Western Europe and an accompanying need to educate professionals in the developing fields of science and technology. There was also a need for specialised schools (for example, Schools of Mines) to accomplish this since the universities of the time, formed as early as the first half of the 12th century, were cloistered institutions, focused on the study of classics, theology and law. The earliest attempts at organised technical education were made in 1702 with the establishment of a School of Mines in Frieberg, Germany (Table 1) to service rich copper mines, and in 1747 with the establishment of a School of Mines in Paris. By this time, the industrial revolution was well under way and other Schools rapidly followed, at Clausthal in the Ruhr region of Germany in 1775; in 1777 at Almanden to service the mercury mines of Spain (later transferred to Madrid); in 1780 at St Petersburg, Russia and at Falun, Sweden in 1819. The academic staff for these new institutions were often trained in the original School at Frieberg.

Jan 1, 2002

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

By Gus Van Weert

The cost of oxygen is a major and common factor in the hydrometallurgical processes developed or proposed tor the oxidation of refractory pyrites. This cost involves charges for the generation and the transfer of the 02 to the mineral slurry. Bio-oxidation faces considerable design demands which require large scale equipment to be resolved. Nitric acid assisted oxidation offers low cost oxygen units; this method of pyrite oxidation deserves a closer look for large scale plants treating pyritic gold ores and concentrates.

Jan 1, 1990

By A. E. Nagel, J. E. Carpetta, M. G. Zabetakis, T. D. Moore

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

By G van Niekerk, M Wortley

Screening is a critical part of many mineral processing circuits and keeping the aperture of the screening media within specification is vital to ensure efficient performance of the processing plant. Typical ways of estimating and/or measuring the wear of the screening media vary from very subjective methods (for instance, using the human eye) to manually checking the width of a few of the more severely worn gaps with a measurement device. Subjective methods can be flawed by human error while manual checking can distort the polyurethane or rubber materials that are used in several types of screening media. All of these errors can cause either premature replacement of panels or, even worse, poor screening of the material.Metso Process Technology and Innovation (PTI) and Metso Screening Media Solutions (SMS) have developed an innovative method that measures screen aperture using advanced image processing techniques. Field trials of the device are presented in this paper, which shows the comparison between the different methods of measuring apertures. Case studies demonstrate how the system, when combined with ScreenTrack, MetsoÆs industry leading maintenance system, and screening media, is providing users with the best possible screening solutions.

Sep 26, 2011

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida&apos;s sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants&apos; and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique?s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay, and silt formations.

By David Guy, John Stanbury, Gilbert Tallard

"In 2009, storm surge from Hurricane Sandy inundated the Bay Park Sewage Treatment Plant located at El. +4 to +12 (+1.2 to +3.6 m) in East Rockaway, Long Island, NY. With all systems down, raw sewage water mixed in the floodwaters. A recurrence of such an event being unacceptable, and in view of rising future sea levels, a flood protection project was developed by Nassau County with funding coming in large part from the federally funded Sandy Rescue Fund. Designed by Arcadis/Hazen & Sawyer Engineers J.V., the protection took the form of a perimeter barrier capable of withstanding future storm surge. Due to limitations imposed by property lines and existing facilities, a levee design with three different types of cross section was developed to adapt to each location, adding construction complexity. The Long Island subsurface is characterized by beach sand extending to great depth. The clay required for the core and levee cover therefore had to be brought in from out of state. A thin silty clay layer at El. -23 to -25 (-7.0 to -7.6 m) served as an aquitard. The under-seepage was reduced by a hanging cut-off wall designed as a vibrated beam thin wall and filled with a salt water resistant, low permeability, self-hardening slurry.INTRODUCTIONOn October 29, 2009, Hurricane Sandy hit New York City, with a devastating effect on the region. The low lying Bay Park Sewage Treatment Plant (STP) (Fig. 1) serving Nassau County on Long Island was submerged (Fig. 2). All basements and underground mechanical facilities were flooded (Fig. 3) and millions gallons of effluent were released into the waters of the nearby Hewlett Bay which connects via other small waterways to the Atlantic Ocean."

Jan 1, 2016

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique’s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay,

Jan 1, 2017

By Olivier Martin

In busy and historic cities, traditional open box metro stations are becoming outrageously difficult, unacceptable for the citizen and uneconomical. Hybrid stations provide an interesting alternative. In-house experience of Gautrain (South Africa), West bay (Qatar), Cairo line 3A (Egypt), and Melbourne (Australia) all aim to reduce disturbance to the city and its inhabitants during construction. Constructed in rock or in deep soil under water table, they take advantages of the latest construction techniques from cement grouting to freezing, and from traditional excavation of cavern to large tunnels constructed by sophisticated tunnel boring machines (TBM). Today, they form the ultimate construction challenge.

Jun 13, 2021