Search Documents

By Joseph Blake Smith

Coal resource data from published sources and company files were used by the Bureau of Mines to determine the location and extent of strippable coal reserves in Wyoming. Total strippable reserves of 23 billion tons were estimated in seven major coal areas. Seven large strip mining operations were active in 1969, and their production totaled 45 million tons of coal. Cutoffs used to define strippable reserves were (1) minimum coalbed thicknesses of 5 feet; (2) overburden-to-coal ratios of less than 10 cubic yards of over- burden per ton of coal; and (3) total overburden thicknesses of less than 120 feet, except where reserves occur in multiple beds or a single thick bed. Tertiary rocks along margins of the Powder River basin contain most of the strippable coal reserves in Wyoming. The Wyodak beds, ranging in combined thickness from 30 to 1.30 feet, crop out on the east flank of the basin and contain an estimated 19 billion tons of strippable subbituminous C-rank coals under less than 200 feet of overburden. Partings between these beds total less than 60 feet. The 100- to 200-foot-thick. Healy bed on the western flank of the basin and the 35-foot-thick School and 20-foot-thick Badger beds on the south also contain large strippable reserves. Elsewhere in Wyoming, strippable reserves. Elsewhere in Wyoming, strippable deposits are subbituminous coal of Late Cretaceous and Tertiary ages, mostly in the Hanna and Great Divide basins in the south-central portion of the State and in the Kemmerer-Hamms Fork region in the southwestern corner.

Jan 1, 1972

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By T. L. McCall

AUTHENTIC records show that coal mining in Cape Breton dates from the year 1720, when the French military authorities obtained coal from what is now known as the Blockhouse seam, in the Morien district, for use at Louisburg, where the fortress, now of such historic interest, was being built. Thereafter, coal was mined more or less continuously, and although, for many years, in a very haphazard way, there was, on the whole, a steady growth towards a better regulation of the industry, culminating in the year 1825 with the arrival of the General Mining Association in Nova Scotia. This Company, more generally known as the G.M.A., had acquired extensive tracts in Brazil and Colombia and had also purchased the mining rights for the whole of Nova Scotia-excepting such areas as had been previously leased-the attraction being the rich veins of copper currently reported as occurring in the Province. These fabulous copper veins, upon examination, failed to materialize, but the engineer sent out to report on them returned with such good accounts of the coalfields he had seen that steps were taken immediately to investigate them. From that rime onward, the history of coal mining in Nova Scotia is one of progress and achievement. One of the first acts of the G.M.A. was to acquire the areas already leased to other concerns and develop these in a masterly fashion, employing the best machinery and talent available at that time. Such dominant control over the minerals of the Province, although it led to orderly development in the several coalfields, also, later on, resulted in restricting operations in the various coal centres to such an extent that a determined effort was put forward by the people of Nova Scotia to end such a state of affairs. Consequently, in 1857, the original lease of the G.M.A. was abrogated, the Company, however, being allowed to retain certain areas in the districts it had already developed. This opened the way for the formation of other coal-mining companies, and numbers of these immediately sprang into existence in the various coal-mining centres. In 1893, the Dominion Coal Company, Limited, was formed by the amalgamation of seven companies operating in the neighbourhood of Glace Bay, in Cape Breton. Later, in 1910, the Dominion Iron & Steel Company, Limited, obtained control of the Cumberland Railway & Coal Company, which had been formed in 1884 to acquire the rights of the two companies working in the Cumberland County coalfield.

Jan 1, 1936

By R. S. Dean

This report, the third of a series of annual reports of the Metallurgical Division to be released in this form, covers the fiscal year July 1, 1936, to June 30, 1937. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By John W. Frey

Although there are certain general uniform provisions in the laws ... of the several Provinces of Canada the differences are so great that it is considered advisable to present digests of separate mining laws rather than a digest of Canadian mining law as an entity . This analysis , accordingly , has been divided as follows : Nova Scotia , New Brunswick , Quebec , Ontario , British Columbia , and a group of Provinces under Dominion Law .

Sep 1, 1930

By Arman Hazrathosseini, Ali Moradi Afrapoli

Fleet management systems (FMSs) as the pivotal part of any surface mining operation find it essential to evolve from conventional into intelligent systems because of both Mining 4.0 requirements and some shortcomings inherent in conventional methods. However, this novel transformation needs to be investigated technically and strategically. To this end, the previously published research works on intelligent FMSs are explored to track the latest status of these third generation frameworks within the surface mining context. Following that, their underlying models are compared in terms of five categories of allocation and dispatching features to pinpoint the technical gaps ignored. Having drawn the future lines of research, the present article then leverages the popular SWOT analysis method to outline the strengths, weaknesses, opportunities, and threats associated with the advent of these intelligent FMSs in mines of future. By and large, the analysis indicates that advantages outweigh disadvantages. Solutions are offered to address the existing weaknesses and threats.

Nov 10, 2023

By M. Pearson, J. Irvine, L. Mercer, P. Lauzon

Severe service ball valve performance has a direct impact on the mechanical availability of high pressure oxidation and leach plants. The primary function of these valves is to isolate the autoclave for maintenance. Valve failure has historically contributed significantly to the maintenance downtime of these process plants. An understanding of the root causes of valve failures is the first step in increasing the reliability of the severe service ball valves. A rigorous failure analysis practice has been developed by Hatch for investigating refractory failures in furnaces and kilns based on Kepner-Tregoe methodology. The method has also been modified for valve failure analysis. From a root-cause failure tree analysis of each of the valve components, a list of all potential valve failure mechanisms was developed for ranking and evaluation, along with recommendations for further valve development. The purpose of this paper is to present the reader with the modified Kepner-Tregoe method and examples of this analysis.

Jan 1, 2004

By G. E. Rouse

Anomalies of sulfur dioxide and other gases have been defined, by direct measurement, around various sulfide bodies. These readings were made (1) in soil gas and (2) in the atmosphere, from both ground vehicles and, to a limited extent, from helicopters. Test areas included porphyry copper and molybdenum deposits, sulfide bearing vein systems, pyrite zones associated with sandstone uranium accumulations, and pyrite-bearing mine dumps. Some of the deposits are covered by as much as several hundred feet of overburden or barren rock, while others outcrop, or have been exposed by mining operations. Depending on local conditions, background values of sulfur dioxide in soil gas and the atmosphere range from 1 to 15 parts per billion. Using present techniques, anomalous readings are recognized at approximately two times background. Apparent "depth penetration? on known deposits has ranged to several hundred feet. Readings have been made over known deposits from a helicopter and ground vehicle moving at up to 40 mph. The rate at which the survey may be carried out depends largely on the size and extent of the anomaly. The existence and magnitude of sulfur dioxide anomalies around sulfide-bearing deposits is a function of geology, target size, soil moisture, and climatic conditions such as temperature and temperature changes, barometric pressure, wind velocity, and precipitation. Industrial S02 pollution can effectively mask the presence of the anomalies sought.

Jan 1, 1971

By G. B. Harris

Much has been written over the past decade concerning the disposal of arsenic from metallurgical processes. In Canada, there are proposed regulations which would classify arsenic in the Primary Group of twenty one persistent, toxic pollutants to be banned or phased out. Since many nickel and cobalt ores, not to mention those of copper, gold and uranium, contain significant amounts of arsenic, it is pertinent to assess the current state-of-the-art of its disposal. The literature is reviewed, and it is demonstrated that from a purely chemical point of view, the family of ferric arsenates largely immobilize arsenic. There is clear evidence from laboratory studies that both crystalline ferric arsenate (scorodite) and amorphous ferric arsenates in which the molar Fe/As ratio is at least three (Fe/As = 3) have very low arsenic solubility; plant data are given to support this. The debate over the long term stability of these compounds continues however; the evidence presented for long term stability and for compound breakdown is critically reviewed in the light? of the recent structural studies, and the role of base metals in these compounds evaluated. Finally, conclusions are drawn as to the viability of a purely chemical process for the long term disposal of arsenic from metallurgical processes.

Jan 1, 1993

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By H Ishikawa, R Halomoan, S Palaniandy

The Karara iron ore project is a magnetite operation consist of open pit mining and concentrator to produce high-grade magnetite concentrate. The concentrator has adopted three stages of comminution, ie fine crushing in the high pressure grinding rolls (HPGR), primary ball milling and fine grinding in the TowerMill plus magnetic separation in between these comminution devices. Since 2014, the concentrator has increased the plant feed rate by 18 per cent. Meanwhile, the ore hardness has increased by 13 per cent to a Bond work index value of 15 kWh/t that led to a coarser flotation feed. Karara Mine has decided to shift the comminution workload from the primary ball mill to the TowerMill circuit by bypassing the 100 µm fine screen in between the ball mill and TowerMill circuits. This action has increased the circuit feed particle size distribution with a top size close to 1 mm. The specific energy consumption of the TowerMill circuit was approximately 3.4 kWh/t, and the circuit product sizes (P80) were ranged between 38 and 45 µm. A joint process improvement exercise was carried out to reduce the circuit product size closer to the magnetite liberation size, ie 35 µm. Among the activities were circuit audit, recommendation for improvement, modelling and simulation, multicomponent analysis, implementation of recommendations and quantification of the improvement. One of the key findings was the density effect of multicomponent minerals in the hydrocyclone. The analysis revealed that the low density coarser gangue minerals were bypassed to the hydrocyclone overflow stream that has resulted in a coarser particle size distribution. Meanwhile, more than 20 per cent of fine (-35 µm) high-density magnetite particles were recycled back to the mill through the hydrocyclone underflow stream and increased the circulating load. Based on these outcomes, several recommendations such as conversion to bottom feed configuration, use of smaller grinding media, high operating hydrocyclone pressure and additional grinding power to the TowerMill circuit were made to improve the overall circuit performances. Karara Mine has prioritised to implement those recommendations that have a minimal financial implication. Full-scale plant trials with bottom feed configuration and 17 mm grinding media were conducted to evaluate its performances. These trials have indicated that the grinding efficiency in the TowerMill was enhanced by 10 – 30 per cent. In May 2017, all the five TowerMills were converted to the bottom feed configuration. This paper discusses the impact of shifting the comminution workload load from the primary ball mills to TowerMill circuit and the performances enhancement of the TowerMill circuit. CITATION:Palaniandy, S, Halomoan, R and Ishikawa, H, 2018. Shifting the comminution workload from the primary ball mill to TowerMill circuit, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 163–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By David L. Veith

This report summarizes a Bureau of Mines review of selected literature on the effects of subsidence due to high-extraction underground coal mining on farmland areas. The data are presented for consideration in evaluating the subsidence effects due to similar mining techniques on the prime farmland areas of Illinois. In Illinois the ground water level in the glacial drift is only 2 to 15 ft below the nearly flat to gently rolling ground surface. The main subsidence concern is flooding, as caused by the lowering of the ground surface, and the subsequent effects on crop production. Positive drainage must be maintained in the farmlands, and the need exists for extensive regional planning by the mining and agricultural industries to maximize short- and long-term production from both efforts. The Bureau is cooperating with the State of Illinois to develop basic information necessary for such planning.

Jan 1, 1987

By P W. Wypych, D Curry, A P. Grima

The market has become highly competitive for engineering and equipment vendors, who are challenged to reduce costs while improving efficiency and productivity of mine operations through plant improvements and expansions. Although conveyor transfer systems account for a small percentage of the infrastructure cost of a mine, they form an integral part of the process supply chain. Malfunctions or suboptimal performance can result in substantial financial cost from delayed start-up, unscheduled downtime, reduced throughput and increased maintenance costs.Discrete element modelling (DEM) is a powerful simulation method used to virtually prototype and test the performance of transfer equipment throughout a design cycle. When developed and applied correctly, DEM can provide insight into performance that exceeds the traditional analytical methods, especially when dealing with complex ore properties, behaviour and/or situations.Using case studies sourced from the authors’ recent research and industrial project work, this paper will address the industry goal to increase efficiency and productivity as well as the methods available to the engineers responsible for delivering designs that meet the aims of this strategic approach.The main focus of the paper will be the new calibration technology, which has been developed by the authors to generate DEM material models that are linked to real-world properties and flow behaviours via unique dynamic testing and innovative parameter calibration methods. These calibrated DEM material models can be deployed by engineers into their existing workflows, whether it be for feasibility studies, concept or final design, plant troubleshooting or optimisation.This new technology allows engineers to gain greater insight than that provided by traditional approaches to the design of transfer chutes and other process equipment and also allows informed design decisions to be made that meet industry efficiency and productivity requirements.CITATION:Grima, A P, Curry, D and Wypych, P W, 2015. New discrete element modelling calibration technology to facilitate the increased efficiency of ore handling and processing operations, in Proceedings Iron Ore 2015, pp 449–464 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By Harry W. Campbell

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied parts of the 19,747-acre Lower John Day (OR-005-006) and 7,538-acre Thirtymile (OR-005-001) Wilderness Study Areas in order to evaluate their identified mineral resources. The study areas are located in Gilliam and Sherman Counties, OR, about 13 mi west of Condon. The area is underlain by the Miocene-age Columbia River Basalt Group. The Thirtymile study area is inferred to have 790,000 yd3 of subeconomic gold resources averaging 93.8 mg/yd3 gold ($1.21 yd3 at a gold price of $400 per oz) in two river bars. The Lower John Day study area has five river bars with gold occurrences totaling 1.0 million yd3 and averaging 13.5 mg/yd3 ($0.17 yd3) gold. A preliminary mining feasibility estimate suggests gold could be profitably mined in the study areas from placer deposits containing at least $3.83 yd3 in gold content. Stone, sand, and gravel occur in the study areas, but more accessible deposits are closer to regional markets. No mines or prospects are in or near the study areas; however, one lode mining claim, now abandoned, was located in the Thirtymile study area. Oil and gas leases cover both study areas.

Jan 1, 1987

By E. R. Rodriguez

Improved practice resulting from recent changes in the method of supplying compressed air and in pneumatic drilling equipment used in secondary drilling and in development work at the Morenci mine of the Phelps Dodge Corp., has resulted in improved safety conditions, as well as in a reduced cost per foot of drilling. A large stationary compressor installed outside the mining area and the compressed-air pipelines in the mine were replaced by portable compressor units. A self-propelled, self-contained drilling unit was obtained for drilling large footages where short moves were involved. Large wagon-drill units were replaced by faster and lighter drill machines and conventional bits by carbide insert bits. The safe practices employed in air drilling and in the related blasting and scaling operations have contributed to an excellent safety record at this mine. The complete sets of instructions listed in the company codes of safe practice aid materially in training employees.

Jan 1, 1956

By M. Y. Levesque

The Australian Government?s Energy Efficiency Opportunities (EEO) program launched in 2006 obliges companies that use more than 0.5 PJ (petajoule) or roughly 139 GWh (gigawatt hour) per year to conduct an energy assessment in order to identify measures to improve energy efficiency. The opportunities identified by the mining sector were assembled in the Mining Significant Opportunities Register that permitted companies not yet embracing and adopting an energy management program to see what those who are, were doing and how much energy was saved, and helps disseminate best practice. The measures can be filtered by company, year, category or equipment type. The creation of a central repository of energy efficiency initiatives is valuable but this existing database could be improved; fields identifying the energy and carbon emission savings associated with a given initiative are a surprising omission. Consequently it does not permit the relative effectiveness of different measures for energy and carbon reductions to be readily assessed. A review of energy management efforts implemented in the mining industry, published in peer reviewed journals, corporate sustainability reports or industry publications during the last 40 years has revealed many examples of best practice. However, the lack of a standardized reporting framework in any of these sources has made it difficult to assess the effectiveness and compare the adopted energy management measures ? just as is the case with the Australian register. In an attempt to address these issues, an improved database structure has been created for energy management measures from the mining industry which identifies energy and financial savings arising from energy management initiatives, classifies applications to specific processes or equipment, and recognizes leaders in the mining industry with respect to energy management. The structure of the register includes the key data relevant to energy management in mining that is absent in the Australian version. The mining industry energy management database has been made available in the public domain where stakeholders can examine the best practice examples. Mining energy champions may also contribute to the register by providing case studies; a standardized entry template affords a quality assurance dimension that is absent in other reporting initiatives. Adoption of this database with its standardized reporting mechanism will enhance transparency of the mining industry in energy matters and help it maintain its social license to operate.

Aug 1, 2013

By Charles T. Steuart

The Arkansas Novaculite of Devonian and Mississippian age is the most distinctive formation in the central Ouachita Mountains of Arkansas from the standpoint of both topography and lithology. The formation typically forms precipitous, narrow ridges (hogbacks) which reflect the steepness of dip and the resistance and thickness of the rock units. The Arkansas Novaculite varies from less than 200 feet thick in the north to locally over 800 feet thick in the south and outcrops over an east-west distance of 360 km (200 miles) in the Ouachita Mountains of Arkansas and Oklahoma. Most of the rocks of the formation are highly siliceous with novaculite predominating, and lesser quantities of chert, siliceous shale, conglomerate and rarely sandstone. Novaculite is commonly defined as a homogeneous mostly white rock, translucent on thin edges with a dull to waxy luster and composed almost entirely of microcrystalline quartz. The word novaculite comes from the Latin word novacula, meaning razor hone. This term was first used by Richard Kirwan in his mineralogy text of 1784. The origin of novaculite remains controversial but we believe it was a primary silica derived mostly from the alteration of submarine volcanic-rich materials, with numerous fine biogenic components and some minor clastics (derived mostly from foreland facies via turbidity currents) and deposited as an amorphous siliceous ooze in the deep Ouachita trough. It was subsequently converted to microcrystalline quartz during diagenesis by the compaction of the overlying rocks and the intense Late Paleozoic Ouachita Mountain tectonism. In the central and southern portions of the region three divisions of the formation have been defined: a Lower Division predominantly of light-colored novaculite; a Middle Division of interbedded dark chert and shale; and an Upper Division of massive often calcareous novaculite. In the northern exposures the formation is thinner and contains more black chert and shale, chert-shale conglom¬erate, sandstone and less novaculite. The massive novaculite of the Upper and Lower Divisions is a source of high purity silica (99+%). Indians were the first to use novaculite. They made their various tools and hunting implements from the weathered broken rock until they learned the quarrying techniques. The first white men in the area recognized the use of novaculite for sharpening their tools and knives: previously whetstones were obtained in small quantities from Europe. To this day whetstone is quarried mostly in areas which the Indians and possibly the Spanish previously worked. Some of the current mining practices have changed very little from those of the early quarryman. In areas where the novaculite of the Upper Division is poorly cemented, this friable tripolitic material has found applications in such uses as an abrasive, as a filler or extender in paints, plastics and other purposes. Some of the dense novaculite is suitable as a filler in fire bricks and also in plastics. Because some of it has the tendency to decrepitate when heated not all novaculite can be used for these applications. Several quarry operators are crushing novaculite for road, concrete, and other aggregate. This use was formerly rather limited due to the abrasiveness of the novaculite on crushing and screening equipment. Further potential uses of novaculite are speculative but include application of high purity silica in the production of silicon metal for solar cells, seed or "growing", and fusing quartz for electronics.

Jan 1, 1985

The 3.5 million tones per annum Enterprise mine is the newest underground copper mine at Mount Isa in northern Australia. At a depth of up to 2000 metres, it is the hottest and deepest mine in Australia. In situ rock temperatures sometimes exceed 60¦C requiring the installation of substantial amount of refrigeration to provide safe working conditions for mine workers. The latest refrigeration project at the mine, R67, required the design and installation of the worldÆs largest bulk air cooler and AustraliaÆs largest chilled water plant. The plant is mounted on the surface of the mine and provides 25 MW of refrigeration to cool some 580 kg/sec of ambient air to 11.4¦C. This is equivalent to the production of 6300 tonnes of ice per day. The plant was designed for high availability, as any downtime would result in substantial production losses to MIM, and also had the potential to quickly result in unsafe levels of heat stress within the underground workplaces. The bulk air cooler has been designed for a capacity of 34 MW(R), the expected ultimate carrying capacity of the 7 m vertical intake shaft. Being located well inside the tropics, technical issues such as control of thermal pulldown required special consideration. Also, the bulk air cooler had to be designed to handle whatever demand for fresh air was imposed by the mine below, with over 100 per cent variations in airflow expected, and without loss of thermal efficiency. A substantial program of risk assessment and HAZOP studies was used to protect underground miners from leaks of ammonia into the air or water circuits. Fully automatic control systems result in a totally unmanned plant that is supervised remotely. To improve efficiency, the plant is controlled by the outlet air temperature from the bulk air cooler û the first in the world to be controlled in this fashion. Engineering solutions to address environmental considerations were incorporated at the design stage through features such as the use of ammonia (a greenhouse-friendly gas) as the refrigerant, zero atmospheric discharge and a wastewater collection and re-use system.

Jan 1, 2002

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009