Search Documents

By T J. Sullivan, H Pinkster, G Swarbrick

From 2002 to 2006, longwall mining was undertaken directly beneath the Cataract Tunnel, which is a 100-year-old, heritage-listed tunnel in Hawkesbury Sandstone responsible for delivering 20 per cent of Sydney’s annual water supply. At one location, undermining resulted in movement of at least 350 mm along a known fault that transects the tunnel. During this movement, the continued operation of the tunnel was ensured through a careful system of planning, monitoring and management.Of key importance to the success of the operation was the use of advanced numerical modelling to guide operations at all levels, including feasibility assessment, pre-mine mitigation works, monitoring design, operation performance and post-mining condition. This allowed many aspects of the potential impacts to be explored, including joint movements, rock mass deformations and changes in permeability. A key challenge was to successfully model near-field influences on adverse geological structure due to very far-field effects. This paper explains the model’s conceptual development, calibration, performance and limitations.Modelling provided the confidence to manage the impacts of large mining-induced movement on key infrastructure and ultimately predicted fault movement accurately. The fault movement remains one of the highest ever recorded due to mine subsidence.CITATION:Swarbrick, G, Sullivan, T J and Pinkster, H, 2014. Longwall mining beneath critical infrastructure – prediction versus performance of the Cataract Tunnel, New South Wales, Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 157–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J. L. Jambor

Sulfide-rich tailings accumulated in a 4l-hectare impoundment at the Waite Amulet minesite near Noranda, Quebec, have undergone partial oxidation and destruction of the principal sulfides (pyrite and pyrrhotite) in the vadose zone. Mineralogical studies and whole-rock chemical analyses of 18 samples from 3 boreholes along a cross-section of the tailings pile indicate that the principal chemical manifestations of the alteration are a pronounced depletion in sulfide-sulfur, and an enrichment in total Fe as Fe203' Other elements such as Al, Mn, Mg, Ca, Na, and K in the solids show erratic or inconsistent variations, but a trend to Si enrichment in the oxidation zone is clear. The trend is interpreted to be a relative enrichment whereby the proportion of the stable silicate minerals has increased as a consequence of the consumption of pyrite and pyrrhotite in the oxide zone.

Jan 1, 1989

By P J. Marsh, P J. Bartsch, N J. Semler

Iron Road Limited is currently studying the feasibility of producing 20 Mt/a of high-grade (67 per cent Fe) magnetite concentrate from a 2.6 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate has been tested at a relatively coarse grind size of -106 ¦m. The preliminary flow sheet has been confirmed based on initial mine plans and comprehensive metallurgical testing across the range of mineralisation. Extensive Davis tube testing to predict magnetite recoveries has been conducted over the resource, however this was completed at settings different to the optimised settings developed in the metallurgical test work program.This paper outlines the development of an ore treatment simulation in SysCAD which utilises the mine production plan, the Davis tube test data from the resource, data from metallurgical test work and process design criteria to predict magnetite concentrate deliveries. Mineralogical data, including QEMScan results and metallurgical assessments, were a fundamental basis of the process models which enable predictions of concentrate yield and quality. Power and water requirements are also calculated within the model. SysCAD dynamic simulation has been used to assist with the design of the process plant and downstream infrastructure. The simulation has been set-up to allow iterative integration and optimisation of the mine plan when it becomes available.CITATION:Semler, N J, Marsh, P J and Bartsch, P J, 2013. Iron RoadÆs prediction of magnetite concentrate production from the Central Eyre Iron Project, in Proceedings Iron Ore 2013 , pp 539-546 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By A M. Ebbels, D Pratt

The current commodities super-cycle has seen an explosion in the number of mining projects demanding human resources throughout the world. The demand for key personnel currently far outweighs the international talent pool and will take several years to subside. A highly effective project team can be the difference between a successful project and a bad public relations exercise. Building an effective team and retaining the team members has become one of the major influencing factors for successful project development in the mining industry in the last decade.Increasingly, international teams are being established combining skill sets, subject matter experts, unique previous experiences and diverse cultures to deliver mining projects all around the world.This paper explores the characteristics of a highly effective team, the communication and geographic challenges and some potential pitfalls which influence the ability to form effective teams within the mining industry.CITATION:Ebbels, A M and Pratt, D, 2012. A great project team - Bringing together location and culture, in Proceedings Project Evaluation 2012 , pp 197-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By H. Sevim

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated technically and economically. The objective was to transport, handle, and inject the residues into the old workings of the mine at a minimum cost. This objective was accomplished in two steps: I) Simulation models were developed and utilized in identifying technically feasible designs in each alternative, 2) Technically feasible designs were economically evaluated to obtain the cost-per-ton of material transported. The designs that provided the minimum cost-per-ton were declared optimal An analysis was conducted for varying distances and tonnages to reveal favorable operating ranges of each alternative.

Jan 1, 1996

By B P. Wrench, M J. Gowan, P J. Chapman

Embankment dams constructed mainly of sand or non-plastic fine soils are susceptible to liquefaction, particularly in high-rainfall, high-seismicity environments where there is sufficient water to saturate the materials and sufficient energy from an earthquake to cause liquefaction. This paper shows the process adopted to review the stability of an existing cross-valley, centreline-raised cyclone tailings sand embankment dam.The study showed that two-dimensional stability analyses did not sufficiently capture the potential for instability, overestimating the depth of the critical failure surface. Instead, three-dimensional modelling was required to provide a reasonable representation. Post-liquefaction stability analyses carried out using the three-dimensional model indicated an adequate factor of safety (FoS). The FoS under seismic conditions was still considered to be a concern based on pseudostatic analyses (but noting the limitations of the analysis method).Earthquake-induced settlements were estimated using an empirical approach based on case history records (Swaisgood, 2003). The post-earthquake event settlement was estimated to be in the order of 600 mm, which is considered to be acceptable for the embankment, taking account of the proposed long-term freeboard of more than 8 m under operating conditions and 2 m under the probable maximum flood condition.CITATION:Chapman, P J, Wrench, B P and Gowan, M J, 2015. Review of static and seismic stability of a cross-valley sand tailings embankment in a high-rainfall, high-seismicity setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 163–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

By Stephen Mansfield

Analysing how accurately a blast design is implemented is one of the cornerstones of a successful operation, and critical for mine optimisation. This paper presents a concept that involves the collection and analysis of data for the five stages through which a blast transitions, from budget through to implementation.

Feb 1, 2020

By J Seppelt

The Kanmantoo Copper Project is owned and operated by Hillgrove Resources Limited and is situated in the Adelaide Hills region in South Australia. Mining in the area has taken place off and on over the last 140 years to recover metal from both copper and lead-zinc ores. This paper focuses on the commissioning, ramp up and future outlook for the copper concentrator at the Kanmantoo Copper Project with major focus on issues encountered and operating performance achieved to date.CITATION:Seppelt, J, 2012. Commissioning of the Kanmantoo Copper Concentrator, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 127-136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

By J Jones

A common problem in the mining industry is that company exploration groups operate in relative isolation to the rest of the company; resulting in poor knowledge transfer (Qureshi and Briggs, 2006) and often priority conflicts with mine geology, operations and project departments. In recognition of this problem, Newcrest created a Minerals Division responsible for stewardship and governance of mineral assets across the value chain from reconnaissance to rehabilitation. It was recognised at an early stage that effective collaboration both internally and externally would be required to improve decision making, deliver faster cycle times and improve governance.Collaboration in companies is generally associated with the introduction of new IT functions. However, modern IT-based collaboration systems and practices are relatively simplistic compared to the long-standing practices associated with collaboration and knowledge management in science and engineering disciplines such as geology and mining.The authors of this paper have started a trial of a 12-point plan for effective collaboration, which recognises that significant efficiencies can be gained and barriers to future success removed if more effective collaboration can be achieved between science and engineering divisions in a company along with external professionals and with the collective intelligence (Tapscott and Williams, 2006) of the outside world. To meet growth aspirations some companies, like Newcrest Mining Ltd, are adopting this comprehensive, step change approach by moving from a closed model the isolates mine geologists to an open and collaborative model that uses IT visualisation systems strategically. The paper describes how an open model provides people with the right work environment and the right information at the right time, which will help individuals and workgroups to work more collaboratively day-to-day. The aim is to achieve speed, focus and mitigate risk through an environment where everyone and anyone can contribute effectively (Cisco, 2008).

Aug 22, 2011

By Hamid Maleki

Rock mechanics models are “data-limited,” i.e., one seldom knows enough about a rock mass to use computational models unambiguously. Statistical methods, however, are capable of being applied where there are good data but a limited understanding of certain natural phenomena, such as the creep of rock salt or elevated risk domains associated with violent failure of strata commonly referred to as coal bumps and coal bursts. Important to these evaluations are (1) having statistically valid data collected consistently and (2) incorporation of analytical calculations for quantifying geologic, mining and particularly geotechnical variables. By combining the strength of the statistical and analytical models, an improved “hybrid” model is created and utilized. To demonstrate the use of hybrid statistical-analytical techniques in rock mechanics problems, three case studies are used. The first case study involves a historic examination of a nuclear waste repository in rock salt, where mathematical models are built using excavation con- vergence data to identify significant variables and estimate future deformation and stability. This case study uses the convergence rate at up to 121 locations of different ages and geometries using monitoring data over the facilities' footprint excavated through 1998. The second case study focuses on ongoing analysis of coal burst mechanics and associated factors. Within the last three decades, a hybrid statistical-analytical methodology has been applied for identifying significant factors affecting coal bursts. This final hybrid model utilizes data from 30 case studies from Utah, Colorado, Kentucky, and other Eastern U.S. mines providing predictive capability for the entire United States coal fields. The last case study is the assessment of Castlegate Sandstone escarpment stability using historic data collected over 17,000-ft of sandstone escarpment exposure in the vicinity of longwall operations in Utah. Results from all three case studies are used for demonstrating the utility of the method in solving ground control problems.

Jun 25, 2024

Research 84 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1984

By J. Kulas, J. Weaver, K. Hagley

An assessment of potential groundwater movement beneath the tailing impoundment at the Red Dog Mine was performed, and has indicated a unique aquifer situation within sub-permafrost groundwater at the site. The aquifer was shown to be isolated from both vertical recharge and a real discharge, and is characterized as a virtually no-flow system. The permafrost resulted in a deep aquifer with high tidal efficiency, meaning that variable surface loads are easily transmitted to the fluid. The tidal efficiency has been characterized through analysis of water level fluctuations that respond to earth tides, barometric pressure loads, and loading from the pond.

Jan 1, 2002

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015

By D. Wenstrup, K. Perry, J. Hatfield, P. Sainato, B. Lusk

Concrete-infused cloth is used in several civil and mining surface applications whose circumstances are similar to some of those in underground mining. A feature of this material is that it cannot be overhydrated. In underground conditions, however, the excess supply of water to the cloth for hydration could lead to muddy and potentially unsafe working conditions, as well as resource wastage by supplying more water to the construction site than is needed. The objective of this study is to verify the water-to-cloth ratio and study the effect of hydration level on the strength of the Concrete Cloth product. We found that the strength increases with increased hydration up to a 1:2 water-to-cloth ratio by weight, after which the strength holds steady regardless of additional hydration. This confirms the 1:2 water-tocloth ratio by weight for hydration and confirms that strength is retained even if the cloth is excessively hydrated.

Jan 1, 2014

By Paul A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County constructs twin Tunnel Boring Machine (TBM) tunnels through cohesive soils and rock beneath the Allegheny River and a narrow city street in Pittsburgh, PA. The tunnel alignment includes an historic building on shallow foundations, modern buildings on deep foundations, and an office building constructed directly over the alignment during the design of the tunnel sections. This paper provides an overview and update of the general site conditions, TBM tunnel design, and support of excavation for the TBM launching pit. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed.

Jan 1, 2008

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as derived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems.

Jan 1, 1974