Search Documents

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962

By T. Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With. Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. In 1990, Cyprus Amax began aggressively searching for such an opportunity. Early in 1997, production will commence at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1,750-tonne per day open-pit operation that will produce more than 300,000 ounces of gold per year. This paper discusses the challenges of locating such a prospect, doing business in Russia, developing supply lines, identifying work force capabilities, gaining government approvals, securing financing, arranging for gold sales and ultimately building a facility in this arctic region.

Jan 1, 1997

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems in developing urban areas. Uncertain knowledge of abandoned coal mines also imposes potential hazards in coal excavation operations since water inundation or the release of methane gas is a pricnipal hazard when mine excavation operations break into an abandoned mine. U.S. Army requirements for an effective method for detecting and mapping subversive man-made tunnels have resulted in a surface-operated automatic earth resistivity survey system with a digital computer data processing system. Field tests aimed at demonstrating the system performance resulted in successful detection of tunnels having depth-to-diameter ratios up to 15 to 1. Under the sponsorship of the Bureau of Mines, a similar system was designed and constructed for use in the detection of coal mine workings. This report discusses the hardware and software aspects of the system and the application of the high-resolution earth resistivity method to the survey and mapping of abandoned coal mine workings. In the field tests reported, the targets of interest were both air-filled and water-filled workings.

Jan 1, 1980

Watershed Jll in Jefferson County, Ohio we instrumented in 1977 as one of three watersheds established for the purpose of investigating surface mining and reclamation effects upon local hydrology, sediment discharge, and sediment and water quality. Each watershed was less than 50-acres in size, and was in a different geologic setting within southeastern Ohio. Surface runoff and ground¬water levels were monitored. Samples were taken for sediment determination and chemical analysis prior to mining. Monitoring and sampling continued through the period of watershed disturbance caused by mining and reclamation activities, which began in May 1980 at Watershed Jll. A psuedo-postreclamation period followed the initial cessation of man-machine activity on the watershed. A second reclamation effort occurred in the fall of 1981 and was to be followed by a third in 1982 after observations ceased. A true final postreclamation period was not monitored at this site, because the erosion control practice (terrace diversions) failed after each reclamation. Watershed Jll was a small pasture and wooded watershed with sandstone and shale above the mined coal seam prior to mining. A clay layer under the coal supported a perched saturated zone, termed the top aquifer for convenience. A lower underclay supported a second saturated zone called the middle aquifer. A lower perched aquifer had been dewatered by previous deep mining. After about three years of premine data and about two and one-half years of mining reclamation and psuedo-postreclamation data, the following general observations may be made: 1. The mining-reclamation phase was very short, and the postmining period was characterized by erosion failures and remedial disturbances that kept the watershed condition and size in a state of change. It was impossible to collect sufficient data to confidently characterize the hydrologic-sediment-chemical aspects of the mining period or of a postreclamation period and, most importantly, of the future watershed after its various properties and characteristics have ceased adjusting to its severe disturbance and reconstitution. 2. A seeding of wheat followed by grasses and legumes was not a particularly successful reclamation practice in terms of stabilizing the new soil. Numerous rills and small gullies developed in spite of installed diversions. 3. Storm runoff rates and yields at the watershed outlet increased from the premine, (phase 1) to the mining-reclamation (Phase 2) periods, and remained at or near the Phase 2 level through the postreclamation (Phase 3a) period. 4. The top aquifer changed in physical and chemical character as a result of mining and was becoming reestablished as the project drew to a close; but it is impossible to predict its final configuration or character. 5. Dewatering of the top aquifer resulted in a complete cessation of baseflow because the middle aquifer water table lay below the elevation of the watershed outlet. 6. The top and middle aquifers were merged in one area of the watershed where the upper coal underclay was disturbed. 7. Failure of the diversion terraces and their outlet obscured the effects of the reclamation practice upon sediment concentration and yields. There was little difference in sediment concentrations between Phases 2 and 3a. 8. Drinking water standards were met by surface waters throughout the period of observation except for two samples that exceeded the nitrate-N allowable level of 10 mg/l. 9. In all Phase 3 surface-water samples, iron concentrations were within the limits established by OSM, and manganese concentrations exceeded the regulation level only once. pH fell below the lower regulation level of 6.0 between 10% and 20% of the time. 10. The chemical quality of sediments was generally about the same after reclamation as before mining, with the exception of organic carbon, which decreased.

Jan 1, 1983

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore, and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement, and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risk, the effectiveness of caps and covers, and provide information to aid in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs), and lysimeters. Many of the monitoring devices can be linked to a datalogger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1997

By Frank Haehnig, Harald Krenn, Harm-Christoph Claassen

"The Wadi Dayqah Dam Water Supply Scheme represents one of the most important projects implemented by the Sultanate of Oman to ensure sustainability of water resources. The principal components of the project comprise two dams to impound the Wadi Dayqah, to store and supply drinking water to the local area and to Muscat, the capital city of the Sultanate.The Main Dam with a central spillway is a RCC Gravity Dam with a maximum height above foundations of 75m, crest length 400m; the Saddle Dam is a rockfill dam with central clay core, max height above foundations is 49m and crest length 360m. During construction of the Saddle Dam a key trench was excavated to 10m depth and filled with compacted clay connected to the central core of the embankment. Grouting utilizing cement grout was performed as a single line grout curtain prior to each filling operations. Both Dams are founded on soft Siltstone, Claystone, Sandstone and inter-bedded harder limestone.After construction of the Saddle Dam, once water was in the reservoir it became evident in early 2010 that some seepage was occurring apparently from the right abutment. This seepage became more marked when the reservoir first filled to discharge over the spillway in June 2010. In order to reduce the seepage, additional sealing works by drilling and grouting of a three row curtain up to 80 meter target depth were initiated to supplement the existing single row curtain. Part of this project for the sealing works has also been to drill additional investigation holes to provide more information and confirm extend of the additional sealing works and its limits.Züblin Ground Engineering was awarded the Additional Sealing Works Contract. Whilst Equipment was on Site, the opportunity was taken to carry out drilling and grouting on the Left Abutment of the Main Dam to reduce seepage through that abutment and to install additional standpipe piezometer for future monitoring of seepage patterns.Work on this Contract started on site in January 2013 and was substantially completed in January 2015.At the time of Tender Züblin Ground Engineering propose and Alternative Design in the form of a Secant PileCut-Off Wall, 85m long to a depth of 40m with additional drilling and grouting below the foot of the cut-off which was then included in the contractual scope."

Jan 1, 2016

By John P. Capp

The feasibility of simultaneously burning several paths through a coalbed to develop a multiple path underground gasification system was investigated by the Bureau of Mines during two experiments, Boreholes were drilled through the overburden and into the coal and arranged in a circle approximately 50 feet from a central borehole. In the first experiment, in an area which had previously been hydraulically fractured,5 air was injected at the center borehole. The coal was ignited at the other boreholes and the fire fronts traveled toward the center, counter to the flow of air, to backward burn paths through the coalbed. Two paths were linked during the first 5 days of operation. The outlets of these two paths were throttled and air pressure was increased to maintain the flow of air, but no other linkages were made. Fourteen days after the two linkages these two paths were opened and gasification was carried on for 10 days, but with only moderate success. In an effort to overcome operating difficulties air was injected at the peripheral boreholes, and the gases were drawn off at the center borehole. Reversed flow operations continued for 12 days and two more paths linked. The heating value of the gas generally was higher than 100 British thermal units per standard cubic foot (B.t.u. per std. c.f.). Because only four of seven paths linked, however, the entire system could not be evaluated with respect to product-gas output and recovery of energy.

Jan 1, 1961

By Swaminathan Srinivasan, Aaron J. Muck

"When an opportunity arises to combine state-of-the-art concepts with advanced modeling tools, engineers need to take what they know and apply forward thinking to geotechnical solutions to promote the state-ofpractice. Such an opportunity was seized during the design and construction of the Great American Tower in Cincinnati, Ohio. The forty-one story Great American Tower at Queen City Square – currently the tallest building in Cincinnati – has not only changed the downtown skyline, it is also contributing to the advancement of the state-of-the-art use of auger cast-in-place (ACIP) piles as settlement reducers. Predicted settlements of a traditional mat foundation were excessive, and the costs and construction time associated with traditional ACIP piles extending to bedrock were not preferred. A mat supported on a limited number of ACIP piles, with the piles primarily acting as settlement reducers, was evaluated as the preferred foundation type.Promoting the unique soil-structure interaction of the foundation system with confidence required the use of sophisticated numerical modeling tools. Traditional standard penetration test boring data (SPT) was initially used to develop a numerical analysis of the soil-structure interaction using FLAC 3D software. The model was further modified with cone penetration (CPT) and pressuremeter testing (PMT), along with actual load test results on several ACIP pile elements of varying lengths, but all tipping above bedrock. Through a combined design team effort, and detailed numerical modeling analysis, ACIP piles were recommended for reducing mat foundation settlement. Instrumentation during and post-construction confirmed design assumptions and predictions. Integrating sound geotechnical concepts, and using advanced geotechnical analysis and design methods, traditional mat and ACIP pile foundations were successfully integrated into a unique foundation support system.INTRODUCTIONThe Great American Tower at Queen City Square in Cincinnati, Ohio is located within a region dissected by historical geologic deviances associated with the meander of the Ohio River and glacial progression/recession. Combining a challenging geology, with the development of a high-rise office building afforded the design team an opportunity to combine state-of-the-art soil-structure interaction concepts and method with traditional geotechnical engineering concepts. Such a combination required a variety of field tests, collaboration with the design team and owner, and geotechnical-structural modeling during the design phase. During construction, in addition to materials testing and observation, a variety of instrumentation systems were employed. Together, the data was used to corroborate the design model and make adjustments during construction and further substantiate design assumptions following construction."

Jan 1, 2015

By Al Romphf

Managing blasting-induced air overpressure levels is a key compliance requirement for most blasting operations. Regression analysis, plotting overpressure amplitude vs cube root scaled distance, will often present a level of scatter which should be considered unacceptable. Relying solely on regression-based predictions can lead to overly conservative restrictions that may negatively impact other key performance indicators. Improved methods are needed for accurate overpressure prediction. The Heelan-Blair wavelet has been shown to closely resemble the overpressure waveshape produced when a single charge is fired under typical confinement conditions. The amplitude of a single-hole overpressure wave is influenced by factors such as proximity to the receiver, charge mass, orientation, and confinement both at the collar and face. Additional factors, including timing sequence, barrier effects, wind direction and velocity, must also be considered. The linear superposition method, commonly applied for ground vibration prediction, can be adapted for air overpressure modelling. In blast design software, this approach can consider all relevant parameters and environmental interactions. Given the uniform nature of air compared to rock, linear superposition using realistic elemental wavelets may replace the need to fire a signature hole. Data from 38 single-hole blasts conducted at quarries and mines throughout North America were used to develop and calibrate a linear superposition model. This model reasonably reproduces air overpressure results from full-scale production blasts, offering a practical approach to overpressure compliance and prediction.

Jan 26, 2026

By Robert L. Rough

The 1954 field tests consisted of six experimental shots in relatively deep holes in a sandstone similar to many oil-bearing sandstones. Water-injection measurements were made before and after each shot to establish the change in conductivity of the fluid caused by the shot. The pressure pulse produced by the shot was recorded in nearby holes to monitor the shot and to determine if any relation existed between the change in conductivity and the nature of the pressure pulse. The results of water-injection tests showed the range of conductivity of fluid before and after shooting with two different types of explosives. Because of the large spread in data for similar shots, not enough information was available to evaluate the differences in increased conductivity produced by the two explosives or any relation between the increased conductivity and the nature of the pressure pulse. However, these results, with the results of other tests involving explosive shots in rock, provide guidance for future research on the oil-well-shooting problem.

Jan 1, 1957

By B Murphy, J L. Heath

Installation of flotation equipment is a lengthy and intricate process involving conceptual design, detailed design and layout, equipment installation, equipment commissioning and handover prior to the plant commencing operation. During these steps, mistakes are often made that lead to increased costs and/or schedule delays in bringing the new equipment online.This paper presents a series of recommendations for the installation and commissioning of flotation equipment to minimise mistakes and ensure that plant production commences efficiently with a minimum of resources. The advice herein is based on lessons learnt from recent flotation equipment commissioning. It is intended as resource material for flotation plant designers, construction contractors, metallurgists and operators, and is applicable to both new and existing plants.CITATION:Heath, J L, Murphy, B and Bourke, P, 2014. Effectively installing and commissioning flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 399–404 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

By T. Banerjee, R. deS. Almeida, D. Gudgeon, F. C. F. Batista, L. deÁ. Silva

"Yamana Chapada’s mine is one of the larger copper-gold mines in Brazil. The mine is located in Goiás state, in the central part of Brazil. The mine has estimated Mineral Reserves of 4.1 million ounces of gold and 3.2 billion pounds of copper as of December 31, 2016. While gold and silver are significant, Chapada’s process flowsheet is configured closer to that of copper facilities. This includes a SAG/Ball configuration for grinding followed by flotation. In the case of Chapada, the mineralogy results in higher-than-normal complexity, notably a significant circulating load both in the grinding and flotation circuits. From an operating perspective, the complexities are controllable, but require careful attention to ensure that circulating loads are effectively managed and gold is not lost to tailings. Chapada created an automation roadmap in 2016 designed to increase plant performance (tonnage, recovery and efficiency). Based on strong potential, the project was fast tracked and within 4 months instruments were installed, control algorithms implemented, and training sessions took place to ensure sustainability at site. This paper will follow the Chapada journey from identifying the opportunities through to implementation and testing.IntroductionYamana Chapada mine is a Copper-Gold mine located in Goiás State, Brazil. Although the mine contains large quantities in Mineral Reserve of gold (4.1 million contained oz as of December 31, 2016), Chapada is primarily a copper mine with copper principally found as chalcopyrite. Accordingly, the processing flowsheet at Chapada is comparable to that of other copper mines with a SAG and Ball mill each partnered with a cyclopack, followed by a flotation circuit. While the overall design is conventional, the mineralogy at Chapada results in significant circulating loads both in the grinding and flotation circuits. This does introduce certain complexities for operating strategies and practices, but, importantly, favourable recoveries and elevated processing rates can be maintained, albeit they need to be closely managed. Plant automation helps in this regard."

Jan 1, 2018

By E Widzyk-Capehart

The mines of the future can be envisioned as complex, large-scale technological systems being operated remotely from few centrally located (major cities) operating centres and skeletal crew stationed at the site. These systems will require remotely located human operators to constantly adapt to new and unforeseen system and environmental demands. In addition, the remote operators will need to match system properties to the changing demands and operational conditions, ie must be able to handle the ‘non-design’ emergencies, because the system designers would not have been able to foresee all possible scenarios of failures and provide automatic safety devices for every contingency. Therefore, it is highly important that the operators’ job, which involves problem solving and decision making at the workstation level, is facilitated by the proper interface designs. This paper argues that decision support systems and thus human-system interfaces for the mines of the future should be developed based on the principles of human-system integration that take into account human information processing and cognitive abilities. The information presented to the operator must support the operator in taking appropriate action through a human-system interface designed according to scientific principles of User Centred Design. A case study is presented where an iterative design process was used by CSIRO researchers as an evaluation method involving users (control room operators) at several stages of the user interface design in order to correct any design inadequacies as they emerged. This process allowed the designers to identify any usability issues before the user interface was fully implemented, which subsequently enabled the control room operators to easily adapt to the new interface and carry out all designated tasks in a timely and effective manner.

Nov 22, 2011

By R Hoeppel, D Harimon, A Fisher

This paper examines the importance of examining the relationship between biology and geochemistry when designing a biopile to treat alkaline soils impacted by petroleum hydrocarbons. At a site in Nevada a large, unlined pit was constructed in a loamy sand soil and filled at regular intervals with a mixture of jet fuel, lubricating oils and waste solvents which were set on fire by the local fire department for training purposes. During its period of operation numerous chemicals were also dumped into the pit for disposal purposes, including dichlorobenzene and various chloroethylenes. As a result of these activities a large groundwater contaminant plume was formed. As a part of the site remediation process a decision was made to perform a limited source removal and excavate the top three to four metres of contaminated soil from the burn pit and place it in an engineered biopile. The location of the training pit is in a heavily mineralised basin where the background sulphate level in groundwater exceeds 5000 ppm. Due to naturally occurring biodegradation of the petroleum hydrocarbons a large portion of the sulphate was converted to sulphide which deposited in the soils as marcasite in the anaerobic soils. The initial attempt at soil remediation was to use a forced air treatment scheme that had worked well in small scale laboratory testing. Unfortunately, when attempted in the field on a large scale, marcasite reacted with atmospheric oxygen resulting in internal biopile temperatures exceeding 90¦C resulting in the virtual sterilisation of the soils without remediation occurring. In order to solve this vexing problem Pintail Systems, Inc developed an anaerobic culture that allowed the pile to be operated under anaerobic conditions. Within three months the biopile successfully demonstrated on a large scale significant biodegradation of the refractory petroleum hydrocarbons.

Jan 1, 2004

By Stephen R. Iverson, Jeffrey C. Johnson, Donovan J. Benton, Michael J. Raffaldi, Lewis A. Martin

"The NIOSH ground control safety research program at Spokane, Washington, is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First, photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application. Second, field photogrammetric data is compared to crackmeter data from a deep underground mine. Accuracies were found to average 8 mm, but have produced results within 0.2 mm of true displacement, as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation. Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use.INTRODUCTIONNIOSH Mine Safety ResearchPhotogrammetry systems have been implemented by the National Institute for Occupational Safety and Health (NIOSH) as part of its ground control research to improve mine safety. Conventional monitoring of ground movement has typically focused on movement of a few discrete points that are marked or anchored to instruments. Loss of a designated point or anchor, or the ability to identify a stable point in an unstable area, have often frustrated monitoring efforts. NIOSH researchers are using photogrammetry to conduct full-field measurements of rock surfaces underground. Periodic measurements of the entire surface of a ramp allow patterns of displacement to be observed. Full-field measurements provide much more insight into ground behavior than point measurements.BackgroundPrevious work by Benton, et al. (2014) discussed laboratory calibration and verification testing of two photogrammetry systems being used by NIOSH researchers. Both systems utilize stereoscopic image pairing techniques for photogrammetric reconstruction. This paper discusses how a laboratory system was used to conduct volumetric analyses of testing of shotcrete panels with varying types of reinforcement. The laboratory system was found to be accurate to within 2 mm. Additionally, a field photogrammetry system was found to produce linear measurements within 1 mm of known lengths in laboratory conditions. This system is currently being used at a deep underground mine to observe ground support conditions and deformations that have occurred. This paper discusses comparison of preliminary volumetric measurements of rib deformation to laboratory tests, as well as comparison of the field system against a crackmeter installed across a fault surface where it intersects the ramp."

Jan 1, 2015

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By Kevin R. Johnson, Matt Caskey, Bryan Plaskett

Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical design and construction. These challenges can include constrained sites with limited access and laydown area, vibration concerns for adjacent structures, and the need to complete work within limited schedules. When challenging geotechnical conditions like variable bedrock elevations are present, the need to balance performance requirements with logistical constraints become the driving factor when selecting deep foundation systems. This paper focuses on the deep foundations used for a new elevated pedestrian bridge at a major health care facility in Tampa, Florida. In addition to the technical design requirements, the owner required a deep foundation system that could offer low vibrations, rapid production, and clean installation to limit impacts on their properties and the public roadway that separated them. The paper describes the project specific geotechnical and design conditions, describes Ductile Iron Pile design, and focuses on how installation of the system addressed the unique logistical challenges. In addition, the implementation of a full-scale load testing program to assess compression, uplift, and lateral design capacities is presented. This paper represents one of the few published references for Ductile Iron Piles on projects in the United States.

Oct 1, 2022

By R. L. Miller

"Miners worldwide use a tremendous amount of energy in producing finished minerals for the end user market. In accomplishing this goal, they incur energy costs that can range from 20% to 30% of the total cost of production, so there is fertile ground for cost savings. To unlock this huge value in cost reduction, energy analysis is the key and is broken into several segments: 1. Fuel analysis for power generation 2. Energy supply & demand 3. Opportunity cost for lack of power 4. Backup power 5. Power contracts 6. Energy efficiency 7. Renewable energy 8. Continuous energy management FUEL ANALYSIS FOR POWER GENERATION What is the first thing we evaluate when looking at power supply alternatives for the mining industry’s large power requirements? Is it 1) site, 2) engineering, procurement, and construction companies, 3) independent power producers, 4) turbine vendors, 5) grid connections, or 6) fuel supply, logistics, and infrastructure? In evaluations of power supply alternatives for mining companies with special emphasis in developing countries, there is one over-riding conclusion: reliable fuel supply drives the energy generation economic engine. Evaluating several different fuels including liquefied natural gas (LNG), natural gas, diesel, heavy fuel oil, and liquefied petroleum gases (LPG) among others, the best project outcomes are those where fuel supply, pricing, logistics, and infrastructure are given an extensive amount of time during the analysis stage. In an assessment of the twenty-year costs of generating power from multiple fuels, each fuel’s costs were placed into three separate net present value (NPV) buckets of: 1) capital, 2) operating and maintenance, and 3) fuel. Within a range of 65% to 85% for all fuels, fuel cost was the largest component of the NPV of the life cycle power generation costs. So if 65% to 85% of your life cycle power generation cost is one item, shouldn’t miners spend a corresponding amount of time in the analysis stage fully understanding this key determinant for a successful power project? In developing countries where power generation infrastructure may not exist or does not exist at the same level as is found in North America and Europe, fuel analysis becomes even more important. One of the key questions for fuel importation in developing countries is the draft at existing ports to allow larger vessels to dock at the jetty. Can larger ocean-going tankers dock at the port for off-loading, or is the port’s draft too shallow, thus forcing a Single Point Mooring (SPM) system or Conventional Buoy Mooring (CBM) system to be constructed at substantial capital expense? Once fuel can be imported, sufficient onshore storage capacity should exist, or must be built to off-load the entire fuel cargo from the larger ships. Additionally, the throughput capacity of the pipeline from SPM/CBM must allow a rapid unloading of the fuel from ship to shore to eliminate steep demurrage costs for the project."

Jan 1, 2017